Search Documents

By Shigeru Tsutsumi

The rapid development of transportation facilities in Japan focused the attention of this country on the possibility of converting the existing coal resources (of which there was an abundance) into liquid fuels, for which there was a constantly increasing demand. Previous work had indicated that this could be accomplished by utilizing one of two processes - the Bergius process, in which high temperatures and high pressures were employed to effect direct liquefaction of the coal, and the Fischer-Tropsch process, in which an indirect liquefaction of coal was accomplished by the production of liquid hydro-carbons from hydrogen-carbon monoxide mixtures. This report describes some investigations into the latter process, which was first developed by Fischer and his colleagues in the Coal Laboratory in Muhlheim, Germany, in 1923. By 1932, these investigators had achieved a 60-percent theoretical yield (152 ml. of liquid hydrocarbons per cubic meter of 2H2:ICO synthesis gas) by using a precipitated Co-Th02 catalyst.3/ At the same time (1932), Dr. Kita of Kyoto Imperial University and Messrs. Fujimura and Tsuneoka obtained 145 ml. of gasoline (C5+) per cubic meter of synthetic gas by using a Co-Cu-Th-U catalyst. 4/ This report is a description of the experimental results subsequently obtained at the Fuel Research Institute, Kawaguchi City, Saitama, up to 1935.

Jan 1, 1951

By Jack Parker

Critical width Before we go further into pillar design, we should look into the matter of "critical width," because of its effect on pillar behavior. Critical width refers to the greatest width that the rocks above the mine can span before failure or, if there are pillars, the width to which we must mine before the pillars accept the full weight of the overlying materials. There are theories to help calculate that probable width, and they usually boil down to one-quarter or one-third of the depth of cover; but they don't always fit, and it would be better for us to understand the factors that control local conditions. Critical width may be controlled by the thickness or strength of one or more of the strata above the mining horizon. In a gold mine, we might have a thick granite or basalt above us, perhaps capable of bridging across most or even all of a small ore body. In that case, pillars might have to support nothing, or perhaps just the weaker or damaged rock below the strong main roof. Obviously it would be wrong to design for tributary load on pillars based on some lab-determined rock strength. In some coal mining districts in Utah, huge steps can be seen in the mountain sides, with slopes on weathered shales and vertical cliffs 100 or 200 ft high in thick, hard sandstones. The sandstones are capable of bridging across hundreds of feet, often making mining deceptively easy at first, but it becomes more difficult as greater areas are opened. Sometimes such a mining sequence leads to violent bumps and bursts as the wide spans of sandstone sag and bear down on the working faces, like giant nutcrackers, or as bridges eventually fail, releasing much pent-up energy.

Jan 1, 1993

By M. J. Beus, B. Stewart, S. Iverson

Synopsis U.S. Mine Safety and Health Administration (MSHA) accidents statistics have identified ore-pass hazards as a significant safety problem in U.S. underground metal mines. The statistics show that nearly 75% of injuries are directly or indirectly related to pulling or freeing of ore-pass chutes, the use of hand tools in ore passes, fails of broken rock in ore passes and structural failures of chutes or gates and ore-pass walls. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) are investigating hazards in and around ore passes in hard rock mines. Risk assessment methods, such as fault-tree analysis, have been employed to identify the most probable causes of orepass failures, define research priorities and analyse the factors that result in malfunctioning and unsafe ore passes. Static and dynamic loads are being measured in a laboratory setting with the use of a reduced-scale orepass mock-up. Field tests are being initiated in mine ore passes to determine static and dynamic loads. Data from the test ore passes are being compared with data from the mine to characterize true system behaviour. Computer modelling with the use of closed-form solutions, finite-element analyses and a newly developed particle flow code predicts static and dynamic leads from the flow and the impact of ore and waste in the ore pass. Preliminary results indicate that dynamic impacts from ore and waste rock might be considerably greater than expected. The total static load is substantially less than is typically used fur the structural design of chute and gate support members. It is suggested that damping factors, normal and shear stiffness and mass frictional characteristics have a significant effect on particle flow and resulting impact loads. This is being verified with the use of results from laboratory tests, field tests and particle flow analyses. Ore passes are vertical or steeply inclined openings in a rock mass through which ore and waste are transported and where they mar also be stored. A typical underground mining system is shown in Fig. 1. The arrows indicate the locations of ore passes and loading pockets and their relative configurations. The control of material flow is potentially one of the most hazardous operations in underground mining. According to MSHA data. most of the ore pass-related accidents in the U.S.A. are associated with the loading-unloading cycle and removal of blockages from ore passes. In particular, attempts to free ore hang-ups have resulted in multiple fatalities. The hazards are obvious; there is uncertainty as to when the ore will break loose and miners are unable to escape falling rock to a safe location. Although ore passes and chutes and gate systems for underground metal and non-metal mines roust meet the requirements specified in the U.S. Code of Federal Regulations (CFR). Parts 57 and 75, recent structural failures of ore-pass linings and gates have underlined the lack of adequate ore-pass design standards available to both MSHA enforcement staff and mine engineers. Because of the importance of an ore pass to the safe operation of a mine design criteria need to be assessed and new guidelines developed. Researchers at the Spokane Research Laboratory of the Nationals Institute for Occupational Safety and Health (NIOSH) are investigating hazards in and around ore passes in hard rock mines and studying design criteria for ore passes. The near-term goal is to conduct laboratory and field experiments and computer modelling to evaluate the ore-pass design criteria currently used. Literature searches, field site

By F. D. DeVaney

Metallurgists and coal-washing engineers have used heavy liquids for years in studying the characteristics of ores and coal. By such means true separations can be made between the various specific-gravity increments in the materials examined. To use of heavy liquids has permitted determination of the possible grades of tailings and concentrates by specific-gravity methods on any particular size, and therefore the size to which the ore must be crushed to free the valuable material. The simplicity of float-and-sink separation and the high degree of efficiency attained in the laboratory are factors that commend the method for commercial concentrations.

Jan 1, 1940

By Henry G. Granger

I. INTRODUCTION. REPEATED failures in attempts to work gold-bearing gravels by means of suction-dredges have created the impression that this method is impracticable. The suction-dredges have failed from three special causes excessive wear and frequent breakage of pump-shell, runners and liners; inability to dredge compact gravel which would ,not. readily move towards the intake; and, most important of all, closing. of the suction-pipe by stones too large to enter it. In my opinion, all three causes of trouble may be remedied: the first, by making stronger the parts most liable to wear and breakage; the second, by means for loosening the gravel at the intake; and the third, by sufficiently... Increasing.. the diameter of the suction-pipe. In suction gold-dredges, this diameter has not usually exceeded 10 or 12 in.; whereas there are few profitable gold-fields which can bee considered dredgeable, in which stones more than' 12 in. in diameter, are-.not frequently encountered. II. AN EFFECTIVE SUCTION-DREDGE. In harbor-operations, much larger stones are handled by suction-dredges.., The large dredge of the Henry Steers Contracting Co. worked for nearly four years at League Island, Philadelphia, where it sucked up, passed through the pump, and forced through 3,700 ft. of discharge-pipe; gravel containing boulders up to 200 lb. in weight. This was done with no bad breaks and few shut-downs. The cutter; and liners were the only parts liable to damage, and these were easily replaced with brief interruption of work. The chrome-steel liners are said to have lasted from six to nine months. I am informed that this dredge worked continously for nine

Apr 1, 1909

By Joseph T. Coe, Siavash Mahvelati, Alireza Kordjazi

This paper introduces recent advances in stress-wave NDT systems for use in assessments of in-service foundation integrity and drilled shaft construction. The primary results of the laboratory experiments are very promising, as the acquired image was capable of differentiating changes in pile cross section as low as 0.3 cm. The preliminary results with the same hardware components on a relatively large scale cemented sand model were also promising. A brief overview is provided of both systems including hardware, survey methods, and data processing techniques, followed by a discussion on application of the results to QA/QC of deep foundations. INTRODUCTION There are two main applications in which current QA/QC NDT technology fails to provide sufficient information regarding deep foundation conditions: (1) detection of flaws in outside cover concrete of drilled shafts and corrosion in steel piling; and (2) evaluation of anomalies beneath the bottom of drilled shaft excavations. Previous studies have demonstrated the capabilities of high frequency stress waves for geotechnical and foundation evaluation purposes (Lee and Santamarina 2005; Coe and Brandenberg 2010; Coe and Brandenberg 2012; Coe and Kermani 2016). Higher frequency waves can visualize smaller anomalous features at the expense of higher attenuation and smaller propagation distance. Therefore, the goal of this study was to advance the state of NDT practice by development of a prototype high resolution stress-wave imaging system as proof-of-concept. The equipment and hardware were modular, which allowed simultaneous development of two system configurations for application to in- service foundations as well as drilled shaft excavations during construction. Results are presented based on two large scale soil models. The first laboratory model simulated section loss in an in-service steel pipe pile and drilled shaft foundation (Fig. 1a). The second model simulated anomalous conditions beneath drilled shafts excavations as might be encountered in areas with significant karst (Fig. 1b). For both models, evaluation of foundation conditions relied on the propagation of small amplitude seismic stress waves using hardware similar to those described in Coe and Brandenberg (2010) and Coe and Brandenberg (2012).

Jan 1, 2018

By Hargraves A. J

With increasing depth, stresses and stress phenomena are becoming more important considerations in Australian coal mining.A large number of compressive and tensile strength tests was made on coal and rock cubes cut from samples taken in various Australian collieries. In addition, an empirical impact strength test was carriedout on fragments of the same samples, to obtain a correlation with compressive strength.In one colliery, flat-jack measurements were taken to assess stresses in coal ribs and in the roof.INTRODUCTIONBy world standards, some of the New South Wales collieries are approaching depths of cover considered a maximum for bord and pillar the normal Australian coal mining method. Several South Coast collieries are winning coal at depths of about 1500 ft., and future operations are being planned at deeper cover. Some areas of these deep workings produce considerable quantities of seam gas.Phenomena associated with high stress and copious gas under pressure in the seam violent phenoma presenting a danger and a nuisance in mine working - have occasionally occurred, and the phenomena are being investigated as a whole (Hargraves, 1958), and separately as a gas problem (Bolt and Innes, 1959; Hargraves, 1962) and as a stress problem. This paper relates to the latter - to investigations into the strengths of coals and coal measure rocks, and into the stresses in and about coal seams...

Jan 1, 1962

By Michelle Lostra, Red Blanchette, Jan Babendererde, Greg Colzani

The City of Portland’s Westside CSO Project is constructing a deep tunnel system to reduce combined sewer overflows (CSO) from entering the Willamette River. Several kilometers of microtunneled pipelines connect the existing system to the new tunnel. The alignments encountered a variety of ground conditions, including fill, manmade obstructions (wood, steel piles, debris), fine-grained to dense coarse-grained materials, cobbles and boulders, all below groundwater. A slurry MTBM convertible to varying diameters, equipped with mix shield capabilities, was selected to cope with the conditions. This paper will discuss access shaft construction,

Jan 1, 2005

A commercial Philips X-ray Fluorescence (X.R.F.) analyser was converted to an experimental instrument suitable for determination of the accuracy to be expected of X.R.F. on line analyses of concentrator slurries. Problems with stability of slurry sample presentation were eliminated by a number of minor modifications.By the use of multiple linear regression techniques instrument calibration equations including error terms were determined for copper flotation feed slurries. Results indicated that the accuracy of copper and iron analyses of flowing slurry samples could approach that of static pressed powder samples.Possible means of reducing the error terms to a level of at least that of pressed powdel' samples involve alternative methods of compensating for the per cent solids in the slurry, Design is under way for installation of a plant unit.

Jan 1, 1968

By Annie G. Smelley

The Bureau of Mines is testing a dewatering technique for phosphatic clay waste that will recover a portion of the water lost using conventional waste disposal methods and produce solids suitable for land reclamation. The technique utilizes a flocculant, polyethylene oxide (PEO), that forms strong, stable flocs that can be dewatered on a static screen followed by further dewatering on a rotary screen. In field tests conducted in northern Florida, clay wastes containing a nominal 2.5 pct solids have been consolidated to greater than 20 pct solids. The rate at which PEO-treated material continues to dewater in a mine cut also was monitored. Preliminary results indicate that PEO--treated material will dewater to 30 pct solids in 140 days. Pretreatment of phosphatic clay waste with lime and H202 was shown to improve the dewatering technique for problem clay wastes.

Jan 1, 1985

By Raymond C. Voige

"The use of current electronic technology in the design of new underground mine communications equipment is providing improved and expanded voice communications which can, in turn, contribute to improved productivity and safety. A review of equipment that is now available or under development Includes the following categories:WIRED SYSTEMSI.Pager phones with selective calling, audible and visual alerting and message indicator.2. Mufti-conversation pager phones that use multiwire cable ormultiplexing techniques.WIRELESS SYSTEMSLow-and medium-frequency inductive systems utilizing ""near"" magnetic fields for both vehicular and personal communications.Wired SystemsCommunication systems in underground mines have evolved slowly in many parts of the world. For many years, magnetotype telephones were the only means of communication from one mine level to another and to the surface. These units were located near the shaft and communications to the working areas were limited."

Jan 1, 1981

By A Tawadrous, P D. Katsabanis, S Kim

A series of small scale tests, have been performed to establish the effect of powder factor and initiation timing on the grindability of rocks. The blasts were performed in high quality granite blocks, which were cut from stone prepared by dimensional stone quarry operations. Three different types of granite, Barre, Stanstead and Laurentian, were tested. The charge consisted of detonating cord placed in five holes with water as a coupling medium, or concentrated charges of equal mass of high exolosive, fully stemmed or air decked. Powder factor was varied from 0.39 to 1.17 kg/m3. Charges were detonated simultaneously or with a small delay and in some experiments, detonation waves collided in the middle of each borehole. All fragments were collected and screened, and drop weight impact tests were performed on selected size fractions, using different levels of impact energy, to calculate the resistance of the rock to impact breakage. The work index of some of the blasted samples was measured using standard Bond mill grindability tests. The experiments generally showed increased softening of the rock with powder factor, manifested by the increasing initial slope of the relationship between t10 and impact energy. The rate of change of the initial slope decreased with increasing powder factor. Changes in the work index were small and consistent in trend with the results of the single fragment impact characterization tests. Charge configuration, timing as well as in-hole collisions of detonation waves affected the initial fragmentation but had little effect on the impact breakage of the samples.

Jan 1, 2009

By W. H. Somerton

Many oil-producing formations contain significant amounts of clay. Because of the large surface area and reactivity of such surfaces, the response of the formations to various recovery processes may be dominated by the reactions of fine-grained minerals, including clay minerals, in the formations. Thus, the success or failure of enhanced oil recovery (EOR) methods may be controlled to a large extent by the amount and nature of these minerals in the formations to which the methods are being applied. One of the deterrents to the successful application of chemical EOR methods is the loss of chemicals injected into the formation, to non-oil recovery processes. These chemical loss processes include adsorption onto mineral surfaces, chemical reactions with rock and fluids in the formations, possibly leading to precipitation and plugging of the formation, and trapping of chemicals in parts of the rock structure so that they become unavailable for displacing oil. Chemicals that may be injected include surfactants, polymers and caustic solutions which react with organic acids in the crude oil to produce surfactants in-situ. These losses are most pronounced in fine-grained reservoir rocks containing substantial amounts of clays.

Jan 1, 1984

By T. J. Goff

Keywords: accurate control, matte level, smelting operations, process control, tapping, sounding bar, electromagnetic measurement [ ] Accurate control of matte levels during primary matte smelting operations is desirable in order to improve process decision-making. High matte levels in the vessel could have to disastrous consequences, particularly in the new generation of intensive smelting furnace with deep-cooled copper coolers. Knowing when to commence tapping and a better understanding of melt times can only be improved if the furnace levels are monitored correctly. At Lonmin Marikana Smelter Division it has long been understood that the matte level information being provided by the manual sounding bar is only as good as the operators? following of measurement procedure, their skill in assessing what the sounding bar is displaying, and their individual interpretation of what they are looking at. This paper sets out to show how this problem was identified as an area of major concern to the plant, how a solution was sought and how an electromagnetic measurement system was installed as an alternative measurement to the matte sounding bar system. Other areas discussed in the paper are the difficulties to be overcome when first installing new equipment and how these teething problems were solved by close co-operation between Lonmin and equipment suppliers, which led to some design modifications to the delivery system. In conclusion the paper discusses the results between the electromagnetic measurement and the manual sounding measurement and how best to integrate the generated data into the plant?s process control system for improved decision making.

Jan 1, 2011

By J Samosir, L Snyman

Northparkes was the first mine in Australia to use block cave mining method which relies on gravity and natural rock stresses to fragment and recover the ore. It was also the first hard rock mine to use hydraulic fracturing, in conjunction with CSIRO, to promote caving of E26 Lift 1. The technique was later used on E26 Lift 2 wedge and E48 prior to undercutting.Northparkes production is currently sourced from the E48 Lift 1 block cave mine and E26SLC. The E48 block cave contains economic ore to the north and south of the current cave footprint. To recover this ore the footprint has been extended on the north and south with two extraction drives and one extraction drive, respectively. Modelling of cavability above the additional drives indicated that the cave would not readily propagate to a sufficient height of draw to mobilise the ore and tended to arch over into the existing cave. To address the modelling results and to reduce the risk of the project, rock mass preconditioning was adopted.This fracturing campaign was performed from surface drill holes adjacent the subsidence zone angled to intersect the higher grade and higher elevation ore zones.Optical televiewer surveys, run prior to fracturing, picked intervals and fault zones to be avoided. Holes were resurveyed post-fracturing to detect newly created fractures and as a measure of success of the program.During fracturing operations water and gel fractures were run at varying depths and pumping pressure was logged for each fracture. The mine seismic system monitored significant events and dye in the fluids utilised for tracking water inflow locations during underground inspections.Towards the end of the project, guar fibres from gel were detected within the mill circuit and required treatment to resume optimum processing.CITATION:Webster, S, Snyman, L and Samosir, J, 2016. Preconditioning E48 cave extension adjacent to an active cave, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 471–478 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Géssica Seara Faria

Na produção de bobinas laminadas a quente, além da força aplicada pelos cilindros de laminação sobre a tira para promover a redução de espessura, o material é também submetido a tensões avante e a ré, durante o seu bobinamento e desbobinamento, que devem ser inferiores ao limite de escoamento do material conforme sua temperatura de trabalho. Este estudo trata da caracterização das tensões de escoamento do aço elétrico de grão orientado com 3,2 % de silício em altas temperaturas. A necessidade do estudo surgiu devido a ocorrência do defeito estiramento durante processo de laminação a quente de acabamento em laminadores reversíveis tipo Steckel, defeito este que consiste no estreitamento da largura da tira em regiões localizadas. Isto acontece em função do desconhecimento do limite de escoamento real do material nas temperaturas de trabalho. Os ensaios foram realizados em máquina de tração a quente, em temperaturas previamente determinadas. Através dos resultados dos ensaios, foram determinadas as curvas tensão x deformação do aço e valores limitantes de tensão conforme variação da temperatura, para que o processo não exceda o limite de escoamento do material.

Aug 16, 2017

By M. Veiga

"Mining is an energy and water intensive activity. Increasing energy efficiency and reducing water consumption are two of the key requirements in moving toward a more sustainable mining industry. Water reduction, reuse and recycle options are reviewed, identifying cases where these options have been implemented. Then a novel mine water network design method is described, which analyzes a mine/mill water system in order to identify areas where water requirements and water system energy requirements can be reduced. First, a site water balance is determined and major water consumers and sources are specified. Next, multiple possible combinations of supplying water to mine and mill consumers are compared. Finally, low energy and water combinations are identified.INTRODUCTIONMining consumes vast quantities of energy: The whole mining and metals sector consumes over 12% of the world’s energy (DOE, 2009). Mining also requires large quantities of water, although mining water consumption is a relatively small portion of the overall world water use. Even in relatively dry, mining-intensive countries like Australia and South Africa, mine water consumption is only 2-3% of national water demand (Brown, 2003). However, at the local level, when mining takes place in areas where water is scarce, mine water consumption can severely impact local supplies. In addition, acid rock drainage, leaks from waste impoundments, or direct disposal of tailing into waterways can contaminate surface and groundwater (MMSD, 2002). Mine water systems can be large energy consumers, but better mine water systems can reduce both water and energy consumption. Improving water system design and practice are key strategic requirements in moving toward a more sustainable mining industry.This paper addresses conventional base-metal or precious-metal mine sites, which consist of an underground or open pit mine and a mineral processing plant, or mill. Ore is extracted and processed through the plant to produce a saleable product. Tailing, or waste material, is then deposited in a tailing storage facility (TSF). Any rock removed from the mine with no economic value, or waste rock, is stored without being processed."

Jan 1, 2010

By Gualberto Salas

Dado que la voladura es una de las operaciones unitarias de mayor extracción del mineral -en tanto logra una adecuada fragmentación de la roca con un costo reducido, es necesario lograr una interrelación entre los resultados de la voladura y el de las operaciones unitarias como herramientas que evalúan y optimizan los diseños de los disparos. En ese sentido, el presente trabajo describe las técnicas para el diseño de las mallas de perforación, los programas para la simulación de la voladura y también para medir los resultados, que permitirán realizar los ajustes necesarios para mejorar los resultados de fragmentación y reducir el costo de operación de minado.

Sep 13, 2001

By John Trefny

Although mining is currently one of the smallest academic units on the Colorado School of Mines(CSM) campus, it is alive and well, with nearly 100 undergraduate and graduate students. For many years, Mines has had undergraduate and graduate programs in hard-rock mining. The school has recently transferred its physical mineral processing activities to the Mining Department. The program has also expanded to include tunneling, underground construction and industrial minerals. There are current discussions about increased research activities on cement and other construction materials. The Mining Department also teaches its share of what is called the “distributed core” courses with curricular requirements common to related programs, as well as mining safety and health, in conjunction with our continuing education department.

Jan 1, 2002

By M. Dattilo

The U.S. Bureau of Mines has been conducting research on the use of waste-derived zinc as a partial replacement for pure zinc in the electrogalvanizing process. The end product of this process is automotive sheet, which has enhanced cosmetic protection over previously used cold-rolled (CR) steel. In this study, primer-coated specimens of CR and electrogalvanized (EG) steel were subjected to the on-vehicle environment and monitored periodically by electrochemical impedance spectroscopy (EIS) during immersion in 1M NaCI solution. The results of these tests were compared with immersion-only conditions. Scanning electron microscope (SEM) and energy-dispersive X-ray (EDX) techniques were also used to evaluate the corrosion processes and compare them with atmospheric exposure specimens. EIS was found to measure the corrosion associated with on-vehicle exposure, thus providing an excellent screening technique for evaluation of the performance of EG automotive sheet steel.

Jan 1, 1990