Search Documents

By Robert A. Pond

Heavy (exceeding 35 tons) roadheaders have not seen much use in the United States, but are used extensively in Europe to excavate many types of underground openings in civil and mining applications. Early models of roadheaders were light and suitable only for utility excavation such as drift enlargement or chamber excavation, unless the ground was very soft and easily cuttable. Frontier-Kemper Constructors, Inc. is now using a 45-ton roadheader to excavate two mine slopes in Kentucky and a 70-ton roadheader to excavate a long decline at a new mine in Utah. Results to date indicate that heavy roadhead machines are an effective alternative to both conventional excavation and full-face boring machines in many cases; and where circumstances are favorable are a superior choice. This paper concentrates on applications in the mine development construction industry, but the conclusions are no less valid for civil construction.

Jan 1, 1983

By Dennis R. Dolinar, Jeff Dubbert, Hamid Maleki

The advance-and-relieve method benefits from lateral destressing associated with mining in laminated rocks and a high horizontal stress regime. This stress control method is based on measurements showing that occurrence of rock failure in the roof and floor of an entry (or caving of roof strata in a panel gob) results in redistribution of stresses in adjacent entries. By locating other entries within the shadow zone of the first entry (or gob), improvements in stability can be achieved. Numerical modeling proved useful in studying the basic mechanics of lateral relief while investigating the sensitivity of results to different geologic and mining parameters using controlled experiments. It was shown that failure of rocks near an entry results in redistribution of horizontal stress and shifting of the stress to higher horizons. Measurements from two mines are consistent in showing significant horizontal stress reductions in comparison with the far-field stress regime within the destressed zone. Although the far-field stress regime is very anisotropic, these measurements show near-equal secondary principal horizontal stresses, or perhaps a switch in orientation, as a result of destressing. Stress relief is achieved through lateral movement and relaxation of rocks along weak bedding planes toward adjacent caved zones (or softened zone). Because of cave geometry in the advancing panel, horizontal stress concentrations occur near the cave line both in front of the face and to the sides. The horizontal stress concentration reaches 1.7 times the far-field stress ahead of the face. This stress increase is significant and may cause structural damage in this zone benefiting from additional support. In the next advancing panel located within the shadow zone of the gob, horizontal stresses are significantly reduced in the roof (by 50%). Thus, the stability of future advancing panel can be improved through prudent layout designs and sequencing. The width of the relief zone is significantly influenced by the height of the softened (or cave zone) and rock mass properties.

By L. du Preez, J. D. Steenkamp

This paper introduces the concept of clean steel production from a pyrometallurgist’s perspective to the broader metallurgical community. A simplistic overview of the steelmaking process from iron ore to car body manufacturing is followed by an introduction to the South African steel industry and the technologies that it utilizes. The process is illustrated by an overview of the flow sheet and technologies for the production of clean steel at Saldanha Steel, South Africa.

Jan 1, 2015

An investigation into the causes of variable sulphur content in blast furnace metal produced at No. 4 blast furnace at the Port Kembla works of Australian Iron and Steel Pty. Ltd. was carried out. Theprogramme included an extended and detailed experimental study of a great number of the operating variables of the furnace, on a cast-bycast or four-hourly basis, over fourteen days.Possible causes of the variation were found in irregular operation due to sinter variability, and it was also clearly shown that slag conditions were most important in controlling sulphur contents of pigiron. Some decrease in sulphur variability was achieved, arising partly from this investigation, and it is hoped to try magnesia additions to modify slag conditions for better desulphurizing.INTRODUCTIONSulphur in pig iron is a problem common to many blast furnace operators throughout the world, but the direct causes and means of overcoming them are functions of the available raw materials, and are hence more particular to each plant and its operating practice. Sulphur in hot metal influences the steel-making operations, the rolling operations and the quality of the finished steel. The main problem associated with high sulphur in steel is "hot shortness", which leads to cracking of ingots and billets in rolling, to poor surface finish and to poor welding properties in the finished steel. On the other hand, sulphur is sometimes a desired additive to steel in order to promote free machining properties.Normal means of controlling sulphur A small degree of control of sulphur in steel is available to open hearth operators by alteration of slag volumes and basicity, but any large degree' of sulphur elimination is...

Jan 1, 1961

By G. L. Smith

This paper introduces and defines the concept of a linkage between long-term planning parameters (?global assumptions?) and possible future world views as conceived in scenario planning. Scenario planning, the tool that is used to arrive at plausible future worldviews, is described in the context of the platinum industry. The interpretation of the scenarios into long-term planning parameters is made, followed by an illustration of how the long-term planning process has been adapted at Anglo Platinum to include the notion of uncertainty.

Jan 1, 2008

By F. B. Samani, B. Stabel

The 1,000 MW Hydro Power Station Masjed-e-Soleiman (formerly called Godar-e-Landar) in Iran is under construction since 1992. The rock engineering aspects of the major underground structure, i.e. the powerhouse cavern shall be reported on in detail. The geotechnical investigations are described and results given. The results of several geotechnical analyses are presented. The designed and executed rock support is given. A description of the monitoring systems and typical measurement results obtained during and after excavation are presented. The lessons learnt during construction of the Stage-I powerhouse cavern were applied on the extension of the powerhouse cavern, which is to house an additional 1000 MW. Details regarding the unexpected behaviour of the Mudstones are given. Die 1000 MW Wasserkraftanlage Masjed-e-Soleiman (vormals Godar-e-Landar genannt) befindet sich seit 1992 in Bau. Dieser Artikel berichtet im Detail über die felsbaulichen Aspekte der Untertagebauwerke, insb. der Maschinenkaverne. Die geotechnischen Untersuchungen werden beschrieben und deren Ergebnisse wie die Ergebnisse verschiedener Berechnungen werden präsentiert. Die geplante und die ausgeführte Felssicherung wird angegeben. Die eingebauten Überwachungseinrichtungen werden beschrieben und typische Ergebnisse während des Aushubs und danach werden dargestellt. Die Erfahrungen beim Aushub der Kaverne der Stufe I wurden beim Entwurf der Kaverne der Erweiterungsstufe II, die weitere 1000 MW beherbergen wird, berücksichtigt. Details zum unerwarteten Verhalten des Schluff-/Tonsteins werden angegeben. La centrale hydroélectrique de Masjed-e-Soleiman (dénommée anciennement Godar-e-Landar), d’une puissance de 1.000 MW, est en construction depuis 1992. Un rapport détaillé sera présenté sur les aspects relatifs à la construction en enrochements de l’aménagement souterrain principal, à savoir la caverne abritant la salle des machines. Une description des investigations géotechniques réalisées y est fournie ainsi que les résultats correspondants. En outre sont présentés les résultats de plusieurs analyses géotechniques. L’ancrage dans la roche tel que projeté et réalisé est présenté. Une description des systèmes de contrôle ainsi que les résultats de mesures typiques obtenus au cours des travaux d’excavation sont donnés. Les leçons tirées lors de la construction de la Phase 1 de la caverne de la salle des machines furent appliquées à l’extension de la caverne de la salle des machines, qui doit abriter une unité supplémentaire d’une puissance de 1.000 MW. Par ailleurs, des détails sont donnés sur le comportement inattendu des argilites.

Jan 1, 2003

By Francisco Geraldo Toledo Junior

Os aços inoxidáveis possuem características essenciais para um bom acabamento quando o que se busca é estética e boa resistência à oxidação. Quando se específica um aço inoxidável, o acabamento é um dos aspectos relevantes que devem ser considerados. O acabamento possui uma importante influência em algumas características do material como, por exemplo, na facilidade da limpeza e na resistência à oxidação / corrosão. Há uma grande variedade de acabamentos. Através de ensaios de oxidação a quente, medição de potencial eletroquímico, medição de dureza a baixa carga (microdureza) e medição da tensão residual via difração de raios x foi possível perceber uma diferença entre os acabamentos 2D, 2B, RO, BB, Nº4 e Nº6. A medição de tensão residual mostrou qualitativamente que o aumento de dureza e o forte amarelamento ocorrido no material com determinados acabamentos é função de uma deformação elástica na superfície imposta durante alguns dos processos de fabricação desses aços. Esse mecanismo é relevante e interfere na resistência a oxidação e corrosão nos casos estudados.

Aug 17, 2017

By Jürg Schlumpf

Concrete is one of the decisive construction materials, also for the AlpTransit Gotthard Tunnel. The client has many requirements, and many are the solution possibilities that concrete systems can offer. Cement producers and concrete admixture manufacturers have been challenged to design and test jointly concrete systems for cast and sprayed concrete. The testing operation followed the scenario laid out by the Gotthard AlpTransit Project management?s instructions ?Testing system for concrete mixes.? Various supplier teams have applied for the concrete systems for sections Amsteg/Erstfeld, section Sedrun and/or sections Bodio/Faido and have also followed through with the tests. As was to be expected, the rate of failed mixes matched the level of the requirements. Thanks to this system, it was nevertheless possible to test complete concrete systems for all sections and to get them approved. The joint ventures tendering for the contracts were allowed to include only approved mix designs in their bids. Workability and durability are of paramount importance for cast and sprayed concrete mixes. Durability is influenced by the chosen mix design where binder concept and well-defined water content, i.e., impermeability, are determinant. Aggregates for AlpTransit are to be considered as given. The concrete mix design also determines workability. Because ambient conditions and also requirements with respect to workability are subjected to change, it is necessary that the mix designs include control measures. The choice and number of components for the concrete systems (cement, additives and admixtures) allow adaptation to changing conditions. For AlpTransit such adaptive measures must meet very strict requirements.

Jan 1, 2008

By W. Lin, M. J. McPherson

When a large area of open gob collapses suddenly, a windblast is produced that can cause considerable damage throughout the infrastructure of a mine. In a few cases, the windblast has been accompanied by ignitions of methane and/or coal dust. This paper describes the conduct and results of laboratory tests involving the compression of mixtures of air, methane and coal dust under a falling weight and while allowing controlled escape of the mixture. The transient responses on pressure and temperature sensors were recorded. In addition to an analysis of those records, the paper highlights those conditions in which ignitions occurred.

Feb 24, 1997

By Rodrigo Galves De Lucca

As tendências do mercado são de utilizar tubos com maior resistência e tenacidade para a temperatura de projeto. Resultados obtidos em testes de laboratório para diferentes ordens de produção e graus, a partir de testes de tração de chapas e tubos, juntamente com a quantificação microestrutural, proporcionam uma oportunidade para melhor compreender e quantificar a influência de cada fase sobre o comportamento das propriedades mecânicas do material. A presença de maiores quantidades de ferrita acicular/ferrita poligonal, em vez de ferrita poligonal/perlita, geram um aumento das propriedades mecânicas durante a formação do tubo, bem como uma forma bem definida do comportamento de tensão-deformação, o que é benéfico em aplicações de strain based design.

Aug 8, 2018

By A D. Campbell, G R. Power

The objective of the draw strategy in a caving mine is to maximise economic return by minimising waste dilution3 and maximising ore recovery4. The draw strategy must also include suitable controls for air blast and mud rush hazards and is highly constrained until continuous cave propagation has been achieved. This paper details a three-year project at the Ernest Henry Mine (EHM), which used cave flow simulation software to develop a draw strategy that increased the mine value by 32 per cent.Dilution and ore loss can be significant in sublevel cave (SLC) operations and result in poor recovery and considerable economic losses. To minimise dilution and ore loss, cellular automata software was used to simulate cave flow over the mine life. The optimisation project required mining footprints for various cut-off grades to be developed. Draw strategies for each mine footprint were then generated using a range of shut-off grades. Economic assessment of each scenario was then conducted to determine the mine footprint and corresponding draw strategy that generated the highest NPV (net present value). The iterative simulation process was improved by developing automated software functions in the flow modelling software to reduce time taken to generate and assess life-of-mine (LOM) draw strategy scenarios.In addition to improving the NPV of the mine, the optimisation project also enabled a decrease in the mine cut-off grade which increased the ore reserve and extended the mine life. Overall, an iterative process of mine planning, cave simulation, economic evaluation and geotechnical analysis was used to significantly increase the economic return of the SLC whilst ensuring caving risks were controlled to an acceptable level.CITATION:Campbell, A D and Power, G R, 2016. Increasing net present value by a third at an operating sublevel cave mine using draw strategy optimisation, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 167–174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By David Smith, Bernie Martin

The Queens Bored Tunnels consist of 11,000 feet of 19'-6" inside diameter tunnels mined through rock, mixed face and dense glacial till, constructed with bolted gasketed one pass reinforced concrete liner. The tunnels are to be excavated with a pressurized face TBM, either EPB or slurry. The construction of the tunnels will require ground stabilization in the mixed face area, instrumentation and monitoring of railway infrastructure, underpinning of bridges, relocation and protection of utilities, demolition of some industrial buildings, construction of open-cut approach tunnels and emergency exits and vent plants. The purpose of this paper is to describe the scope of work, the suggested methodology and the proposed construction schedule.

Jan 1, 2005

The Purification of Low-Grade Quartz Ore by Flotation and its Mechanism

Sep 13, 2010

By K A. Bunker, A D. Campbell, E Ah Mu, A R. Penney

The Ernest Henry mine is a transverse sublevel cave (SLC), which is relatively unique due to the 45 degree inclination of the orebody. To economically recover ore, each sublevel is horizontally offset from the previous level by around 25 m, depending on the orebody geometry. Mine development, slotting and initial production within this zone occurs in a high stress abutment that increases in magnitude at depth. These areas are seismically active and close to the hanging wall where cave propagation is yet to initiate. High stress conditions and the close proximity to the cave seismogenic zone results in challenging geotechnical conditions in the step out zone of each level and requires management of hazards including stress driven rockfalls, rock bursts and pillar failure.This paper outlines how these hazards were forecast using numerical modelling and geotechnical monitoring. Risk management techniques included dynamic ground support design, development of a new mine layout and extraction sequence as well as delayed re-entry into seismically active areas. Ongoing monitoring, instrumentation measurements and field observations were used to track the effectiveness of the controls.Future production levels are forecast to experience increasing stress and seismicity, which will increase demand on excavations and installed ground support. Ensuring the techniques and controls for monitoring, measuring and mitigating stress and seismic hazards are enforced is essential for continued safe production.CITATION:Campbell, A D, Bunker, K A, Ah Mu, E and Penney, A R, 2016. Managing stress and seismicity in an inclined sublevel cave, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 319–328 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By W. Sondermann

"AbstractWith the increasing demand in reuse of inner city areas and the urgent need for deeper foundation pits under cramped circumstances, adjacent structures close to and high ground water level, the well-known established technologies especially with small to mid-sized dimensions are often too time consuming and occasionally not economic to install lateral support systems. The alternatives for these specific cases could be the usage of the deep mixing technology to create lateral support systems in reinforcing the deep mixing elements additionally to transfer the horizontal loads from earth – and water-pressure.With increasing demand in depth and water tightness, verticality and overlapping of single column solutions are becoming the key in execution. In addition, for some applications subsoil-conditions were not ideal for wet deep mixing technologies. The tubular soil mixing system (TSM) as a combination of mechanical mixing and support of hydraulic cutting by jet grouting can provide solutions toovercome these challenges.1. Current market conditions and trendsThe present financial crisis and the efforts not only to consolidate national budgets, but also to rescue certain banks, have not left the building industry unaffected either. Some drastic cutbacks to public budgets, along with the increasingly restrictive granting of credit for the financing of construction projects, have led to enormous over-capacities in the building sector, with purely negative impact. As a consequence of these negative developments, many companies are experiencing the pressure to restructure more quickly and to reduce costs but at the same time to keep the consequences of all activities, both externally and internally, within limits acceptable to employees, owners and finance institutions and last but not least consumers."

Jan 1, 2014

By Pedro Henrique Moura Costa

Com o estudo realizado em artigos técnicos e acadêmicos e vivência no ramo industrial, ficou evidente uma deficiência no desempenho dos sistemas de controle regulatório das plantas industriais. Parte dessa deficiência é proveniente da falta de engenheiros de controle para auditar as malhas de controle regulatório. Foi realizado em um forno de tratamento térmico, um trabalho de auditoria das malhas de controle regulatório, baseando-se em uma metodologia já existente na literatura. Levantou-se informações do processo do forno como, os controladores automáticos, o sistema de aquisição de dados e a infraestrutura de rede de automação e por seguinte, as implementações dos PID's no CLP. Após essa contextualização, métricas para avaliar o desempenho inicial das malhas foram utilizadas e então, o funcionamento dos elementos de controle utilizados no forno foram diagnosticados através de ferramental estatístico e análise dos sinais na ferramenta PIMS. Adquirido o conhecimento necessário sobre o processo e o diagnosticado de maneira concisa, ações corretivas e de otimização foram realizadas e propostas com o intuito de otimizar o desempenho das malhas de controle. Por fim, os índices de desempenho do sistema são recalculados e os valores comparados com os valores pré auditoria, concluindo que pode ser possível melhorar alguns dos principais termos adotados no negócio como redução de custos, aumento de produtividade e sustentabilidade.

Jul 30, 2018

By Tony Moore, Peter Riccio

"MMG (Minerals and Metals Group) operates the LXML Sepon’s mineral processing facility located 40 kilometers north of the town of Sepon, in the Savannakhet Province, Lao PDR. The Sepon copper plant produces 70,000 tons/year of LME grade A copper cathode using leachautoclave- SX/EW-flotation technology (Baxter et al., 2003). Pyrite recovery in the flotation circuit is critical to the operation, as it is used to generate acid and soluble ferric ion for the leach circuit. Low pyrite recovery has been an on-going challenge in the flotation circuit. Final tailings characterization work done by Ian Wark Research Institute (Bassell et al., 2006) showed that the pyrite losses to the tailings are made up of a combination of coarse liberated particles and finer particles that have been coated by clay fines.In December of 2005, a joint Cytec-MMG technical program was initiated to address the pyrite recovery issue. A series of diagnostic tests were performed in the Cytec Stamford Research Facility using synthetic plant water showing that the collector was precipitating as a metal salt and was unavailable for mineral attachment. The tests also identified several collector chemistries that would likely be robust in the low pH (< 1), high dissolved metal ion environment and will not complex with metal ions in solution. With the support of the Sepon on-site engineers, an extensive, successful laboratory program was completed, which was subsequently followed by on-plant testing that showed a step wise improvement in pyrite recovery.INTRODUCTIONLow pyrite recovery has been an ongoing problem in the flotation circuit at Sepon. Sulfur recovery (indirect measure of pyrite) was improved from 40% to 65%-75% in mid-2005 when on site laboratory work confirmed that AERO® 8045 Promoter was a more effective collector then AERO® 407 Promoter. However, sulfur recoveries above 65% could never be achieved. Sepon requested the Ian Wark Research Institute to complete a surface analysis study using Scanning Electron Microscopy, X-ray Photoelectron Spectroscopy, and Time-of-Flight Secondary Ion Mass Spectroscopy to determine if clay coated pyrite played a role. It was concluded that the pyrite losses to the tailings are made up of a combination of coarse (+ 100µm) liberated particles and finer (-74µm) particles that have been coated by clay fines. The majority of the losses appear to be due to the former. In December of 2005, a series of diagnostic tests were performed in Stamford using synthetic plant water in order to identify what chemistries would likely be robust in the slimy low pH and high dissolved metal ion solution environment. Results showed that several chemistries would not complex with ferric, ferrous or copper in solution and therefore should perform well in the Sepon flotation. The incumbent collector, AERO® 8045 Promoter was complexing with metal ions in solution. This resulted in the collector not being available for adsorption onto pyrite."

Jan 1, 2011

On April 5, the potlines at Consolidated Aluminum Corp.&apos;s 35,000 ton-per-year primary aluminum smelter at Lake Charles, La., were frozen when natural gas lines were accidently cut by a dredge. Full production is expected to resume in 3 to 4 months. Three primary aluminum producers announced plans to restore much of the idled capacity in the Pacific Northwest as a result of a special power allocation by the Bonneville Power Administration. Reynolds Metals Co. planned to bring a total of 40,800 tons per year of capacity back onstream at Troutdale, Oreg., and Longview, Wash. The Aluminum Company of America (Alcoa) will restart half of a 23,500 ton-per-year potline at Vancouver, Wash. Kaiser Aluminum & Chemical Corp. planned to restart a 27,500 ton-per-year potline at Mead, Wash., and to bring an additional 10,000 to 20,000 tons per year back onstream at Mead and Tacoma, Wash.

Jan 1, 1980

By Haiping Sun, Samir Ganguly, Oleg Ostrovski, M. Yaser Lone

Wettability of graphite by synthetic SiO2-Al2O3-CaO-MnO slags with varied MnO content and by industrial slags was studied at 1350-1600 °C using sessile drop method under argon atmosphere. Initial contact angle was the lowest (110-115o) for the MnO-free slag. For slags with 10-40 wt% MnO, the initial contact angle was in the range 125-135o. The contact angle decreased with the contact time. The change in the contact angle with slag mass was found insignificant. The surface tension of slags obtained from the drop shape analyses was 500-800 mN/m and varied in a narrow range with temperature and MnO concentration. The reduction rate increased with increasing MnO content in the synthetic slag from 20 wt% to 40wt% and temperature. Increasing temperature also increased the rate of reduction. No correlation was observed between the reduction rate and MnO content in the synthetic slags in the range 0-20 wt% and in the industrial slags. The rate of SiO2 reduction from the molten slag was close to the rate of MnO reduction. The MnO-free slag had the largest contact area with graphite substrate. Keywords: reduction, wettability, graphite, slag, manganese, surface tension.

Jan 1, 2007

By M. N. Rubin

This report summarizes the work performed under USBM contract J0100018. The purpose of this work was to document the currently available noise control techniques that can be incorporated into new coal preparation plants during the design stage. This was accomplished by reviewing the related experience of the contractor and subcontractor (Bolt Beranek and Newman Inc.), conducting an extensive literature search, visiting operating coal preparation plants, and contacting various equipment manufacturers. The treatments addressed include equipment substitution, changes in plant layout, and retrofit treatments for existing equipment.

Jan 1, 1982