Search Documents

By J. He

The separation performance of a raw coal sample from South Africa based on the dense gas-solid fluidized bed beneficiation technique was investigated. Analysis showed that the raw coal sample distributes mainly in the -50+6 mm size range with the -1.6 g/cm3 density fraction accounting for 78.20% of the cumulative mass distribution. A flow sheet of the sequential coal beneficiation technique was introduced. The experimental and simulation results of the hydromechanical and density distribution stability indicate that the dense gas-solid fluidized bed could provide a stable separation environment with uniform density fluctuations under suitable operating conditions. With the application of this technique on the raw coal sample, the separation results show that three products, consisting of 73.25% clean coal with an ash content of 9.59%, 11.31% middlings, and 15.44% gangue were effectively separated at two different densities of 1.82 g/cm3 and 1.57 g/cm3. This study provides an effective flow sheet for achieving the high-efficiency separation performance on raw coal from arid areas. Keywords dense gas-solid fluidized bed, dry coal beneficiation, density distribution, separation efficiency.

Jul 1, 2013

By K. Morin

"Silver and gold leaching by cyanidation is a well-known process used around the world. This reaction is often accompanied by the leaching of other species throughtout the cyanidation circuit that causes the diversion of cyanide towards non valuable by-products (SCN-, Cu(CN)x, Fe(CN)x, etc.). One of the detrimental impacts of the formation of these by-products is the precipitation of silver-cyanide complexes that occurs when cyanide concentration is too low. Without any extra-addition of free cyanide, the precipitated silver is lost and cannot be recovered causing an important economic loss. To overcome silver precipitation, cyanidation circuits are often operated at higher cyanide concentrations. Recently, COREM’s research team has been working on a technology to measure and control silver precipitation during the cyanidation process. Moreover, a methodology has been elaborated in order to evaluate threshold cyanide level which corresponds to the cyanide concentration at which silver starts to precipitate. This technology has been tested on site on a real cyanidation circuit at Agnico Eagle’s LaRonde mine."

Jan 1, 2014

1. Domestic Production and Use: In 1984, 12 companies operated 27 primary aluminum reduction plants, with 3 firms accounting for 57% of production. Washington, Oregon, and Montana accounted for 35% of the production; Indiana, Kentucky, Missouri, and Tennessee 25%; Alabama, Arkansas, Texas, South Carolina, and North Carolina 20%; other States 20%. Based on published producer prices, output of primary metal in 1984 was valued at $7.2 billion. Aluminum consumption by 25,000 firms was centered in the east-central United States. Packaging accounted for an estimated 35% of domestic consumption in 1984, transportation, 20%; building, 18%; electrical, 9%; consumer durables, 8%; and other uses, 10%.

Jan 1, 1985

By ALEXANDRE CALDELLAS BARBOSA

O objetivo desse trabalho é planejar e controlar a chegada de veículos para carregamento nas plantas ArcelorMittal Tubarao e ArcelorMittal Vega, apresentando uma agenda com os horários disponíveis para o transportador escolher. Esse processo de escolha de um horário disponível é suportado por uma agenda gerada pela usina, considerando as restrições operacionais e de capacidade de expedição por ponto de carregamento. Programar a chegada de veículos aumenta a previsibilidade da necessidade de recursos adicionais para realizar o carregamento e assim não gerar filas, não perdendo produtividade no processo de transporte com veículos parados. A ausência da programação tem uma abrangência muito maior que apenas perda de produtividade e atrasos, ela também eleva o custo total de transporte da cadeia de suprimentos. Visando aumentar a competitividade e melhorar a previsibilidade do processo de expedição, foi implementada a solução para regular o fluxo de chegada dos veículos, sistematizando o processo de agendamento do veículo para carregamento.

Oct 30, 2017

By Luiz Henrique Dias Alves

O trabalho consiste na avaliação das Tensões Residuais através da técnica dos Furos-Cegos. O componente em estudo consiste em chapas de Aço A36 aplicadas para compor a estrutura de prensas hidraulicas. Com auxílio do software Solid Works versão 2013, foi realizado a simulação do estado de tensões sofridos pelas chapas quando a prensa hidraulica encontra-se em trabalho, determinando assim o seu fator de segurança. Em seguida, pelo método da aproximação sucessiva, foi adicionado furos-cegos ou furos passantes com diâmetros variados ao longo da geometria das chapas a fim de verificar o comportamento dos estados de tensões. Portanto, através da aplicação de furos-cegos nas chapas, foi possível identificar o diâmetro e posição ideal que permitiu um ganho significativo no fator de segurança das chapas, permitindo assim, reduzir o número de chapas no processo impactando diretamente nos custos e no tempo de fabricação do equipamento.

Oct 30, 2017

By R. Venugopal, Saxena. V. K., U. Sankrityayan

"There is a dire need of a technology which can break the mineral interfaces to enhance liberation with minimum energy consumption in mineral beneficiation processes. Understanding of mineral crystal system and interfaces is essential to develop such methodology. So, this study is carried out to find out the role of mineral crystallography in milling and liberation. Data related of mineral crystallography, Vickers Hardness Number, Bond Work Index and beneficiation processes were collected from literature and detailed statistical analysis has been carried out to establish a correlation among these parameters. It was found that atomic weight and cell parameters shown statistically significant relationship with Vickers Hardness Number of minerals, which controls the milling characteristics of ores. Liberation characteristics of five different kinds of ores were analyzed considering the types of interfaces between valuable and gangue minerals. It was found that phase interfaces play vita role in liberation and coarser liberation can be achieved in the minerals of incoherent crystal systems like manganese and zinc ores. Study of this subject can help us to understand the effect of stress wave propagation in solids and its effect on crystal interfaces. It can also help us to design a technology of future to break the mineral interfaces.INTRODUCTIONCommunition is energy intensive mineral processing operation and consumes up to 2% of the total electric power generated in the world. Energy consumption due to comminution is increasing every year as there is growing needs to exploit lower grade ore bodies and process rejects (Blazy et al., 1994; DOE, 2005). Low grade ores require crushing and grinding to liberate the valuable minerals which are further separated from gangues by various beneficiation methods like gravity separation, floatation, leaching etc. Currently, comminution methods are selected based on the reduction ratio and energy consumption but effect of grinding methods on subsequent processing methods specially on liberation also need to be studied to optimize the entire beneficiation process. Most of the attempts made in past to minimize the energy consumption in milling to enhance the mineral liberation were focused on compression mechanism, chemical additives, thermal treatment, microwave treatment and electric disintegration (Kilpelm and Austin, 1982; Norgate and Weller et al, 1994; Bearman et al., 1997; Kumar et al., 2010; Wang el al., 2011; Singh et al., 2012). But the role of mineral crystallography on milling and liberation behavior of minerals not fully explored yet."

Jan 1, 2013

By Gordon E. Agar, Brian Lyons, Gregory H. Styles, William B. Kipkie

"Rock rejection during the flotation of a copper-nickel ore was improved by adding carboxymethyl cellulose to both a rougher and cleaner flotation stage. The selection of the rock depressant was based on laboratory rates studies. Plant operating results are presented which confirm the laboratory selection of two particular brands of carboxymethyl cellulose.The rock assay of the concentrate was reduced from more than 40% to less than 15%.IntroductionThe traditional method of selecting flotation reagents relied upon batch bench scale tests, conducted under arbitrary conditions, to identify the effect of the reagent under examination. Too often these were ""one-off"" tests with little or no regard paid to the reproducibility of the results. Sophisticated researchers used statistical methods to design and evaluate the experiments but they were still obliged to rely on the arbitrary and often unreliable batch tests to generate the numbers that were analyzed statistically. An interesting side-effect of the enhanced sophistication of the statistical analysis was often that no significant effects would be uncovered in a series of experiments that would have generated many positive conclusions and much further experimentation if the same results had been evaluated by the traditional method.In the recent past, at least two groups of researchers a have directed their attention to the reliability of the batch experiments with a view toward improving the reproducibility of the test data. In this work the best of the improvements advocated by both of these groups have been adopted in order to generate kinetic data from batch tests that are as reproducible as possible.The objective of the work was to reduce the rock content of a bulk sulphide concentrate produced at Inco's Shebandowan mill. During 1982 the Shebandowan concentrate analyzed 3.5% Cu, 7.4010 Ni, 25% pyrrhotite and more than 40% rock, which resulted in an MgO content of 10.4%. Besides the expense of shipping all of this rock to Sudbury, the rock also contributed to the poor filterability of the concentrate. On favourable occasions the moisture content of the filter cake was slightly over 20% by weight. The magnesia content of the concentrate was deleterious to the reverberatory furnaces used by Inco for smelting nickel concentrate because the slag viscosity increased as the magnesia content increased, and the nickel lost in the slag went up."

Jan 1, 1987

By Pablo Espinoza

En esta investigación, con criterio de circularidad se identificó la oportunidad de aplicar una variante del proceso SART, ya que en el flujo proveniente de la precipitación de plata y oro denominada solución pobre o barren la concentración de cianuro Wad es superior a 2000 mg/L. Por otro lado, en los depósitos de mineral piritoso expuesto a la intemperie se generan flujos de drenaje ácido de diferentes características, destacando dos de pH menor a 0.5 unidades y altos contenidos de metales solubles que son tratados actualmente en una planta de neutralización y precipitación de metales.

Sep 29, 2023

By Héctor Ugarte y Chamorro

El presento trabajo revisa las diversas medidas preventivas de seguridad minera que se dieron en el periodo colonial peruano. Durante la colonia, la deplorable situación económica y social del indio, conlleva una reacción de defensa humanitaria por parte de los frailes a través de leyes en favor de los indios. Posteriormente en 1551, el virrey La Gasca elaboró una serie de medidas como "Las leyes de indias", "Las ordenanzas de nuevos descubrimientos y poblaciones",entre otros, que protegian a los indios. En 1783 se dictaron "Las Ordenanzas de minería" para la nueva España y fue el virrey Francisco de Toledo, el primero en dictaminar la construcción de pozos y puentes en lugares convenientes, castigando a los infractores. En su Ordenanza II, refiere el caso de las minas de Potosí y ordena no desbaratar puentes ni pilares para evitar riesgos inútiles, mientras que su Ordenanza III dispone la regulación de las escaleras seguras de scrinejas. Asimismo prohibió el trabajo de menores de edad y el "pallaqueo" de mujeres en la mina. En cuanto a la salud ocupacional refiere, el virrrey Toledo dispuso la distancia entre el humo generado por el plomo y zinc, y los trabajadores, asi como su indemnización durante tres meses. Don Juan Solórzano fue otro de los partidarios que ordenó la eliminación del régimen de "obrajes"puesto que era excesivo para la salud de los indios. Las "Ordenanzas de la minería" rescatan también la valía de los operadores mineros, así como las "Declaraciones de Escobedo", donde se estableció la ventilación en el lugar a explotar y la supervisión adecuada de parte de un guardaminas calificado por algú facultativo de la minería. Tanto estas ordenanzas como otras disposiciones tuvieron su base en el Derecho romano. Finalmente, en los inicios de la República, el químico y primer director general de minería, Mariano Eduardo de Rivero y Ustaríz inspeccionó los centros mineros de Puno y Huancavelica, y dictaminó un decreto como medidas de protección para los obreros expuestos a enfermedades y accidentes ocasionados por el mercurio. Dicho decreto está compuesto por 8 considerandos y 4 artículos y apela a los conciudadanos a cumplir las normas en beneficio, salud y seguridad de los trabajadores mineros.

Jul 20, 1959

The National Institute for Occupational Safety and Health (NIOSH) conducted a monitoring field study to optimize the rib control plan in a room-and-pillar coal mine. The study mine is located in the Central Appalachia coal basin. Two monitoring sites were selected at different sections in the study mine. The selected sites have different overburden depths and geologies. The instrumentation plans at study sites include borehole pressure cells installed at various depths in studied pillars, rib and roof extensometers and load cells mounted on number of the rib bolts. The instrumentation results and observed geology for one of the study sites showed great potential for optimizing the rib bolt plan at that section of the mine. Therefore, a rib support optimization study was followed using numerical modeling technique. A calibrated threedimensional model was developed using the instrumentation results of the optimization section. The calibrated model was used to determine the optimum rib support for expected overburden depths and rib heights. Baseline rib bolt patterns were assumed for the optimization study. Additional rib bolts, above and beyond the baseline bolting parameters, were outlined and identified as solutions to contain the rib fracturing identified by the modeling results.

Jul 28, 2020

By E. A. Metz

It has been approximately four years since IARC reclassified crystalline silica as a “Group One” substance. Since that time, crystalline silica has been considered a human carcinogen. Silicosis is a preventable disease and several aggressive campaigns have been developed to increase awareness of silica dust related problems in the industrial environment. New analytical techniques are being developed to determine quantitatively the amount of crystalline silica in materials. Yet, still much is to be learned about the surface properties of silica and the way in which the disease progresses into full-blown silicosis. This paper will discuss the interaction of free radicals generated by the mineral particles and lung tissue. It is the cell injury and DNA damage that progresses to fibrogenesis. Freshly fractured surfaces of silica contain free radicals. These free radicals play an important role in the stimulation of the alveolar macrophage and the development of the inflammatory reactions leading to the fibrotic response caused by silica. Engineers, scientists, and physicians need to discuss the mineralogy of silica and the technical issues concerning the development of silicosis.

Jan 1, 2000

By D. H. Desy

The Bureau of Mines has conducted research on the ignition of methane-air mixtures by sparks caused by frictional impact of aluminum alloys on rusted steel at typical coal mine fan speeds. The objectives were to establish the incendivity of aluminum alloys under these conditions, to investigate differences between aluminum alloys, and to evaluate substitute materials for the aluminum-steel combination. With a specially designed apparatus, three commercial aluminum casting alloys and a number of experimental aluminum alloys were tested for incendivity of the frictional impact against rusted steel in flammable methane-air mixtures. All aluminum alloys tested produced some ignitions. Of the experimental alloys, the harder alloys and those containing silicon tended to be more incendive than the others. With the normal experimental conditions, constructional steel, stainless steel, brass, and plastic did not cause ignition of methane-air mixtures in frictional impact against rusted steel. Some ignitions occurred with constructional steel at high speed in more flammable gas mixtures enriched with oxygen. From these findings, it is suggested that constructional material combinations other than the aluminum-steel combustion would minimize this inc endive hazard. A detailed description is given of previous research, and comparison is made with present results where appropriate.

Jan 1, 1975

By Ch. Schroeder, F. Collin, R. Charlier, Y. J. Cui

The paper proposes two numerical models ot the mechanical behaviour of chalk. First, an elasto-plastic constitutive law reproduces the different plastic mechanisms of the chalk and the influence of pore fluids by introducing the concept of suction. Secondly, a model able to reproduce time dependence behaviour. Eventually, the paper gives a simulation of an academic reservoir during depletion and waterflooding phase. Der Artikel stellt zwei numerische Modelle des mechanischen Verhaltens der Kreide vor. Das erste ist ein elasto-plastisches Modell, das verschiedene plastische Mechanismen der Kreide und den Einfluss von Porenflüssigkeit, unter dem Begriff der Suktion, reproduziert. Das zweite Modell berücksichtigt darüberhinaus das zeitabhängige Verhalten. Schliesslich zeigt die Veröffentlichung eine Simulation einer theoretischen Lagerstätte während der Entleerung und der Wasserinjektion. L'article propose deux modèles numériques du comportement mécanique de la craie. Le premier est une loi élasto-plastique qui reproduit les différents mécanismes plastiques de la craie et l'influence du fluide interstitiel par l'introduction de la notion de succion. Le second est un modèle prenant en compte les effets différés. Enfin, l'article présente une simulation d'un réservoir académique durant les phases de déplétion et d'injection d'eau.

Jan 1, 2003

Paper written on project work carried out in partial fulfilment of B.Sc. Eng. (Extractive Metallurgy)degree The concepts behind support vector machines are very interesting both in theory and in practice, as they are based on a universal constructive learning procedure derived from the statistical learning theory developed by Vapnik. In this paper, their application to time series modelling is considered by means of simulated data from an autocatalytic reactor. In particular, reconstruction methods from non-linear dynamics are used to define a state space model for the process. Multivariate embedding techniques are compared to scalar embedding with respect to modelling. Keywords: System identification, Support vector machines, Multilayer perceptrons, Non-linear dynamics

Jan 1, 2003

By Yves-Laurent Turcotte

Notre conférencier, Monsieur Yves L. Turcotte, Vice-président et Directeur général chez Promaintech Novaxa est diplômé en génie industriel de l?Université du Québec à Trois-Rivières et détient une maîtrise en gestion de projets de l?Université du Québec à Montréal. Il est une véritable sommité canadienne dans le domaine de l?amélioration de la performance des organisations. Provenant d'entreprises manufacturières et de services, il possède plus de 20 ans d?expérience en tant que développeur de technologies, conseiller et formateur auprès d?entreprises. Il a à son actif la réalisation de mandats dans plus de 400 entreprises. Il est reconnu pour sa grande capacité d?analyse et pour trouver des solutions novatrices et profitables aux problèmes des organisations les plus complexes. Aujourd'hui, il dirige Promaintech Novaxa, une division de DMR, qui a célébré son dixième anniversaire en 2006. Cette organisation ayant des places d?affaires dans la région de Montréal, Québec et Vancouver compte plus de 50 professionnels et a une carte de visite dans 16 pays. Les axes d?intervention sont le Management, la Productivité, la Fiabilité, l?Innovation et l?Amélioration Continue.

Feb 1, 2008

By L. K. Weaver

The Bureau of Mines has started an engineering study of oil recovery by miscible-phase displacement. As a preliminary part of the investigation a literature and patent study was made to prevent duplication of work already done, to become acquainted with those actively engaged in research of this type, and to learn where the recovery method has been attempted. This bibliography gives results of this study. The bibliography includes 254 references to U.S. and foreign patents and published literature relating to miscible-phase displacement processes of oil recovery. It is divided into the following sections: (1) U.S. patents, (2) foreign patents, (3) literature references, (4) author index, and (5) publication and source reference. The patents and literature references are listed alphabetically by author by intervals of years. References to February 1963 are included.

Jan 1, 1963

By Késsius Bortolan Menezes

O complexo Minas-Rio da Anglo American iniciou suas operações em agosto de 2014. A usina de tratamento produziu, em 2016, cerca de 15,5 milhões de toneladas de concentrado. O minério, explorado em Conceição do Mato Dentro (MG), passa pelas etapas de cominuição, classificação, concentração e separação sólido-líquido antes de ser bombeado por 529 km até São João da Barra (RJ), onde é filtrado, estocado e embarcado para exportação. Durante a fase de projeto, a utilização de equipamentos pilotos com capacidade de centenas de quilos por hora foi de fundamental importância para verificação da viabilidade técnica do tratamento do minério. Contudo, a realização de um teste exigia um esforço muito grande, devido aos grandes volumes de minério necessários. Por isso, com o início das operações, os testes em escala de bancada começaram a ser mais explorados. Além deles, testes em mini planta piloto com capacidade de dezenas de quilos por hora são muito utilizados, pois permitem simular de forma simples diferentes circuitos. O trabalho tem por objetivo mostrar essa evolução histórica na utilização de ferramentas para avaliação do desempenho da flotação, com exemplos de resultados práticos obtidos, e como os mesmos influenciaram a tomada de ações que culminaram em melhorias industriais.

Oct 30, 2017

By Clarence R. Zink

A problem has always existed in deep and fast drilling situations such as coal overburden drilling, or when drilling with a tight annulus, such as 9 7/8" bits and 8 5/8" pipe. This problem is the difficulty experienced by blasthole bit and blasthole drill rig manufacturers to attain large jumps in bit and drill rig productivity through bit and rig design, when drilling in these specific situations. In other drilling situations, these large jumps in productivity have been easily attained.

Jan 1, 1998

By Ron J. Elliott, Dylan Wedgewood

A series of five signature holes were blasted at the Highvale Mine and the resultant seismic data was analyzed to make recommendations on how best to address neighbour complaints regarding blast vibrations. From an analysis of peak vibration levels measured at the closest neighbour for blasting during 2016, it was determined that the blast vibration intensity varied between 1.4 to 4.3 mm/sec (0.06-0.17 ins./sec.), well below the level of concern for the onset of minor damage to residential structures, however, the frequency of the blast vibrations was between 2.2 and 9.7 Hz, which is within the range of the natural resonant frequency for a single story home. This was determined to be the cause of the neighbour complaints, as the home would be responding to the blast vibrations.

Jan 1, 2018

By Aline Silva Magalhães

Os aços com médio teor manganês são uma classe da terceira geração de aços avançados de alta resistência (AHSS), combinam propriedades mecânicas como ductilidade e resistência mecânica e são assistidos pelo efeito TRIP, características determinantes para sua aplicação na indústria automobilística. Convencionalmente, tais ligas são produzidas por meio de laminação a quente e a frio, seguidas de recozimento intercrítico. No entanto, o trabalho a morno têm ganhado interesse com o intuito de reduzir custos e tempo operacionais. O objetivo deste trabalho foi comparar a influência da laminação a quente e a morno por meio de análises de microscopia óptica, eletrônica de varredura, difração de raios x, microdureza Vickers e técnicas de EBSD em um aço 8Mn- 0,08C. Observou-se uma microestrutura mais refinada e deformada no material laminado a morno com um maior percentual de austenita retida, o que derivou uma menor dureza. Na amostra laminada a quente, o valor médio de dureza evidenciou uma microestrutura martensítica de baixo teor de carbono. Em relação à textura verificou-se uma maior intensidade de componentes da fibra a na amostra laminada a morno devido a um maior grau de encruamento neste processamento termomecânico.

Aug 17, 2017