Search Documents

By Paul Laframboise, Nigel MacDonald, Mike Hallewell, Robert Thorpe

"Galmoy Mine, owned by Arcon Mines Limited, has operated since 1997, and is one of three operating lead/zinc mines in Ireland. Changes in ore type starting in mid 2002 created challenges to metallurgical operations at Galmoy. This resulted in unacceptable lead and zinc flotation performance, which prompted initiation of a formal plant review and a subsequent stabilization programme. This involved a structured review of operational practices, development of a new Standard Operating Procedure (SOP) which in turn led to significant changes in process control equipment needs in conjunction with extension of zinc flotation cell residence time.This paper will describe the metallurgy of the Galmoy operation. Reasons for the poor metallurgy experienced in 2002 will be described, as well as the solutions identified to overcome these problems. By the second quarter of 2003, these solutions had been implemented and recoveries had risen to record levels.INTRODUCTIONGeneralGalmoy Concentrator is located in County Kilkenny (Refer to Figure 1 below) and was constructed during 1996 and commissioned in 1997.The concentrator at Galmoy had been designed initially to treat 650,000 tonnes per annum of primarily CW ore type. The main mineral of economic significance was sphalerite (Typically 10 to 11% Zn) with some minor galena (0.7%Pb) in a dolomite (Magnesium Carbonate) host rock.The only other competing sulphide mineral was pyrite (Circa 3 to 5% Fe in Mill Feed. This CW ore type predominated the first 6 years of production, but in August 2002, the ore mineralogy changed due to significantly higher levels of pyrite rich G ore body being blended in with CW ore."

Jan 1, 2005

By Thomas T. Read

I. INTRODUCTION. WHEN so much has been written upon a subject on which so little definite information is available as upon this, some reason must needs be assigned for adding to the volume of literature. A sufficient reason is found in the probable great future importance of China as a producer of mineral wealth. The present undeveloped state of mining in the Empire is due to many causes, among which the most important are the relatively simple needs of the population, the lack of transportation-facilities, the inelastic regulations governing the industry, and the superstitious reluctance of the people to make excavations which might disturb the spirits of the earth and air, or of ancestors. Iron is the metal most in demand, yet the needs of the population, until recently, only made necessary a production of approximately 0.5 lb. of iron per capita per year. The present annual production of iron for domestic consumption, in the United States, is nearly 600 lb. per capita. The curious state of development of transportation in this interesting country has been a greater handicap upon the mining industry than upon any other. The point upon which it hinges is the absence of a road-system. Except for a few military roads, now almost impassable, there are no roads in China; that is to say, there is no land which is set aside as a right of way, belonging to the commonwealth. Throughout the agricultural districts, generally speaking, the entire area is in private ownership, and the lines of travel are between fields. There is a constant struggle for existence between the owners of the land and the traveling public, with the natural result that the so-called roads usually

Mar 1, 1912

By S. R. Borrowman

This investigation by the Bureau of Mines was undertaken to develop information on the extractive metallurgy of thorite ores because potential ore bodies of this mineral have been found recently in Colorado, Idaho, and Montana. Basic information on thorite ore treatment that would be useful in appraising the potential of these and other domestic thorium resources was developed. The work was done mainly on thorite ore containing 3.87 percent ThO2 from the Powderhorn district, Colo., and on a composite sample containing 0.52 percent ThO2 from the Wet Mountains district, Colo. Limited tests of d corroborative nature subsequently were made on a sample containing 2.30 percent ThO2 from the Lemhi Pass area on the Idaho-Montana border.

Jan 1, 1962

By Wallace Ernesto Sant Anna Ramos

O Buckman Onsite® é um novo portal web para clientes com interface para um painel de dados, que propicia ao cliente e representante de serviços da Buckman, o acesso a informações essenciais sobre as operações neste cliente. O presente trabalho visa mostrar as vantagens e benefícios de se utilizar esta nova ferramenta manipulando os dados de controladores automatizados, dados de controle manual, ficha de segurança de produtos químicos e outras informações importantes para o processo.

Aug 17, 2017

By J. Pei

The studies of dynamic measurements using stress wave theory has commenced in China. This paper introduces some practical experiences using "CASE method" in Shanghai showing applications of dynamic measurement to determine ultimate bearing capacity of pile, the change of capacity due to set up, determining the optimum bearing layer during pile driving, the efficiency of hammer system and integrity of pile and discussions of method concered.

Jan 1, 2010

By Forrest T. Moyer

Injury experience at coal mines and mechanical-cleaning plants (excluding officeworkers ) in 1967 was 222 fatal and 10,115 nonfatal disabling work injuries during an exposure time of 241.8 million man-hours. These injuries occurred at a frequency rate of 42-75 per million man-hours worked; the severity rate was 7,699 days lost or charged per million man-hours. Each of these general measures of injury experience was lower than similar data recorded for 1966. Employment at 6,885 coal mines and 569 mechanical-cleaning plants, excluding officeworkers, averaged 139,312 men in 1967. The average number of days worked was 220. Coal production totaled 560.8 million short tons, at rates of 2.32 tons per man-hour and 18.32 tons per man-day. A total of 2,779 onsite officeworkers at coal mines and mechanical- cleaning plants worked 5.2 million man-hours in 1967 without a disabling work injury.

Jan 1, 1972

By Eldon C. Pattee

Reconnaisance samples of reported beryllium occurrences in Idaho, Washington, Montana, and Oregon were chemically and spectroscopically tested in a mobile laboratory. The two predominant types of occurrences were green beryl associated with Cretaceous intrusions and disseminated aquamarine associated with Tertiary intrusions. Although the beryllium content of known deposits in the Northwest is too low for economic development at present, total submarginal-grade beryllium resources in pegmatites are estimated to be 570,000 to 1,870,000 tons containing 0.024 to 0.167 BeO. A potential source of 500,000 to 700,000 tons of beryllium-bearing tactite in Idaho and Montana averages 0.033 to 0.080 percent BeO.

Jan 1, 1968

By Fabio Tavares Chamonge

A Decapagem 3 da Usina de Cubatão, instalada em 2013, possibilita a oferta de novos produtos ao mercado consumidor e a agregação de especiais valores àqueles já oferecidos pela Usiminas, incluindo a ampliação do portfólio de produtos. Desde a partida, os resultados da Decapagem 3 evoluíram significativamente, com base nos indicadores de segurança, qualidade, produtividade. Obteve-se consistente redução das dispersões de processo o que resultou, entre outros, em produtos com qualidade superficial superior. Para que isto fosse possível, um abrangente conjunto série de ações foi planejado e executado. Este trabalho apresenta os principais resultados obtidos e as ações implantadas no período inicial de funcionamento da Nova Decapagem.

Aug 16, 2017

By W. Hurst

The authors of this paper, in substituting values in a material balance equation associated with a gas reserve and a water drive, cannot find sustainment of what the gas in place should be; therefore, their conclusion is that this type of problem dealing with gas reservoirs is insoluble. They have introduced the word, "cybernetics," based on the work of Norbert Wiener, that further extends this line of reasoning, namely, to the effect that the system is a "black box", and that the gas reservoir and aquifer can take on infinite aspects 'based upon their past performance, to quote the authors. The inference is that this black box is an unknown. which permits in computer programming to subscribe as many variables as possible to observe by adjustment of one to another those combinations of conditions that fit field behavior. This may satisfy those in this discipline whose dedication is to programming, but to the others this is a comparison to the rationalization of the combinational results of the throwing of dice—a probability procedure. In reservoir engineering we are more direct. We learn from the examination of individual we'll and field data exactly what is in this black box. I now come to the impasse that has confronted these authors in their machine calculations. In this I have reproduced from their own production data (Tables 1 and 2 of their paper) pressure vs cumulative gas produced. shown as Figs. D-1 through D-5. A perusal of any of these five plots, for the corresponding fields in the Po Valley, shows the straight-line relation of pressure vs gas produced, evidencing pressure depletion. The point I make is that in their fundamental production data, there is no variance from a straight line that can support a water drive.

By G. Lyman

The cross-belt sampler is a device that is very widely used even though it has not been ratified by the Standards associations. This paper is concerned with the bias testing of two cross-belt sampler designs against stopped belt samples and a cross-stream cutter at the belt end. The bias analysis is carried out using size distribution as the analyte and conventional t-testing and the Hotelling T squared test, which are compared for their effectiveness. The paper considers the issue of detectable bias and the statistical planning of bias tests.

Jan 1, 2010

By KEITH BARRONI

In the proposed criterion for coal a distinction is made between brittle and "psuedo-ductile" failure. This criterion is the basis for the development of new equations for coal pillar strength, including a transition from brittle fracture to pseudo-ductile yielding. In addition the equations obtained allow the critical minimum pillar dimensions to be calculated to avoid "catastrophic" and "ultimate failure".The validity of these formulae can be tested by comparing their results with pillar case histories derived from the literature.

Jan 1, 1988

By J. Wickens

This paper discusses how Bald Mountain Mine dramatically reduced mercury production by treating process solutions with a liquid reagent called UNR 811A. The reagent is marketed by Cherokee Chemical Co., Inc. A summary of the bench tests comparing several different reagents is given. The ensuing plant trial is discussed and results are presented. The plant trial treatment costs are discussed. Finally, potential cost savings are discussed.

Jan 1, 2001

By D. D. Blue

To insure domestic production of aluminium for, essential civilian and defense uses, the Government, under authority of the Defense Production Act of 1950, programed and promoted an aluminum-expansion program that will more than double the primary production capacity that existed in 1949. In view of this vastly increased production, the raw materials, with respect to both quantity and sources, are reviewed. The raw-material consumption pattern, the requirements during an expansion period when excess quantities of materials for starting up new facilities are consumed, and the probable requirements for production of 1.7 million tons per year of primary aluminum are discussed. The raw materials that presented the most difficult supply problems were bauxite, electrical power, and fluoride salts, and the supply pattern for these materials probably will undergo changes. A major part of the electrical energy for the increased capacity was to come from thermal generation, Jamaica-was to become a major source of bauxite, and synthetic fluoride salts were replacing natural cryolite in increasing quantities. Other raw-material requirements discussed are: Soda ash; lime, and limestone; starch; filter cloth; fuel; alumina; the carbonaceous materials, green and calcined petroleum coke, high-and low-temperature pitch and coke or anthracite; cryolite; aluminum fluoride; the materials going into production of synthetic fluorides, acid-grade fluorspar, and sulfuric acid; and labor. INTRODUCTION The raw materials for the aluminum industry that have received the most publicity are bauxite, the ore that supplies elemental aluminum, and electrical energy, the means by which aluminum oxide is reduced to metal. A number of other important materials are, however, required in large quantities in the production of primary aluminum metal.

Jan 1, 1954

By G. G. le Roux

The purpose of the investigation was to assess various options for increasing the efficiency of the conveyor belt transporting system used at 4 Belt Shaft at Lonmin?s Marikana operations. The reason for the investigation was to prevent the occurrence of a ?bottleneck? at the main ore passes delivering ore to the conveyor belt system, thus creating more fluent operational conditions. The options assessed for increasing the efficiency of the conveyor belt transporting system were: ?Variation of the conveyor speed ?Concurrent tipping from two ore passes on the belt ?Increase the available drive unit power ?Increasing the feed rate from vibratory feeders ?Change in belt width/belt specifications The report shows that the most preferable option to the current situation at 4 Belt, Lonmin, would be the option of concurrent tipping from two ore passes to the belt.

Jan 1, 2008

By B. J. Barfield

Standard erosion plots (4.6 m by 22.1 m on 9 percent slope) were constructed on the Alston Surface Mine of Peabody Coal Company in Western Kentucky to evaluate the effects of placement technique and density on the erodibility and eroded size distribution from mine spoil and reconstructed topsoil. PLots were constructed with a dozer and scraper pan from shale spoil material, topsoil (A horizon) and subsoil (B and C horizon mixture) using soils stockpiled at the Alston Surface Mine. Plots were evaluated under fallow conditions with a tilled plot surface and two compacted conditions. One compacted condition was generated by tracking the surface with a dozer and rolling with a loaded scraper pan. The second was generated by rolling the surface with a solid wheel compactor. Rainfall was supplied with the Kentucky Rainfall Simulator at a rate of 63.5 mm h-l with the plots in three different soil moisture conditions; dry, field capacity, and very wet. Runoff was evaluated for flow rates, sediment concentrations, and aggregate and primary particle size distributions. Sediment yields and the Universal Soil Loss Equation E130 indexes were calculated from the data for each plot. The erodibility was calculated from the tilled plot data using a weighted soil loss and E130 value from the dry, field capacity and wet runs, and a cover management factor calculated for every other condition. For the topsoil and subsoil plots, sediment yield was greatest for the dozer scraper pan plots and lowest for the tilled plots. For the shale plots, erosion rates from the wheeled compacter plots were the highest and tilled plots the lowest. Average erodibilities were 0.14, 0.38, and 0.41 tons ac h ft-1 tonf-1 in-1 hundred ac-1 for the shale, subsoil, and top-soil plots. Cover management factors for each plot were 1.29, 1.42, and 1.17 for shale, topsoil and subsoil plots compacted with the solid wheeled compacter and 1.29, 3.79, and 2.51 for shale, subsoil, and topsoil plots compacted with the dozer scraper pan conbination. The accuracy of the Wischmeier erodibility nomograph was evaluated on the data collected. Erodibilities were accurately predicted for the topsoil plot and poorly predicted for the sub-soil plot. The accuracy of the CREAMS procedures for predicting the composition (size distribution) of eroded particles was also evaluated. The composition was well predicted for the topsoil plots, moderately well predicted for the shale plots and poorly predicted for the subsoil plots.

Jan 1, 1983

By J. Drzymala

Particle beneficiation tests are often conducted to determine how the recovery of a key component of a particle mixture varies with overall product yield, i.e., the separation curve. The results can be misleading when an attempt is made to determine the effect of feed grade by comparing separation curves representing different feed grades or key component concentrations. This is a shortcoming of the conventional recovery versus yield diagram, which may not appear to be affected by feed concentration. To overcome this shortcoming, a method is presented for transforming and normalizing the recovery and yield coordinates so that the separation curves representing dif-ferent feed concentrations are directly comparable.

Jan 1, 2007

By Fumito Tanaka

The Mitsubishi Process is the sole pyrometallurgical process for the continuous production of blister copper from copper concentrates. Continuous converting originates from the application of the proven technology of a lime-ferrite slag (CaO-FeOX-Cu2O) on the Converting Furnace (C-furnace). Recent improvements on the C-furnace operation have included increasing the processing of recycled materials and the investigation of alternative fluxing agents. However, some minor oxides adversely affect C-furnace operation, with respect to magnetite behavior of the slag, with the most significant impact having been observed with the silica content of the slag. This paper will quantify the impact of silica on the lime-based slag, and discusses the controls that have been identified to sustain continuous converting operation.

Jan 1, 2005

By Agnes Ágata Fróes Martins

O ensaio de impacto determina a resistência e sensibilidade dos materiais quando submetidos a uma certa carga de impacto, por isto, a importância deste ensaio. Através dele conhecemos as características que um material necessita ao ser projetado de tal maneira que possa suportar a uma força de impacto. Neste trabalho, o objetivo é comparar os resultados de energia absorvida no ensaio de Charpy analógico com o ensaio de Charpy instrumentado e verificar se há uma diferença significativa entre os resultados. Para isto, ensaios são realizados baseados em normas técnicas, neste caso a norma ASTM E23 [4]. Após os ensaios observou-se que os resultados do Charpy analógico e do Charpy instrumentado não obtiveram diferença significativa para todas as amostras ensaiadas. Em critério de avaliação dos resultados utilizamos a norma ASTM E2298 [8].

Aug 16, 2017

By Edmund Newton

This paper is one of a series comprising the Mineral Industries Survey of the United States, which was begun in 1935. It describes the simple methods of mining and beneficiating manganese ore, in eastern Tennessee and compares these methods with those used elsewhere in the Appalachian region. The report contains general information on manganese to give a clearer understanding of the methods and costs of mining and. beneficiating manganese ore foam a widespread deposit, an in addition presents zone difficulties normally fond in these operations. The marketing, uses, and value of manganese ore are discussed as well as the amount of capital necessary for effective operation on given scale of production, and requirements are outlines for successful operation of manganese, property in this region.

Jan 1, 1941

Innovative and Resource-Preserving Washing Processes for Primary and Secondary Raw Materials

Sep 13, 2010