Search Documents

By Byron S. Kutscher

This report summarizes the program to develop and construct an improved light-scattering dust monitor (ILSDM). This improved light-scattering dust monitor, which operates on the forward light scattering principle, provides instantaneous measurements of airborne dust concentrations in units of mg/m. The program was divided into two phases. Phase I involved the design of the ILSDM which was reviewed by the Bureau of Mines. Phase II included the fabrication of a prototype ILSDM based upon the design developed during Phase I. After completion, the ILSDM was delivered and demonstrated at the Bureau of Mines. A description of the final ILSDM design, operating instructions, maintenance instructions and recommendations for additional work are also included in this report.

Jan 1, 1980

By Dany Pelletier, Yeves Breau, Ahmed Bouajila, Claude Gagnon

"In flotation circuits, direct measurement of the volumetric flow rate delivered by electromagnetic flowmeters is often difficult to obtain particularly due to piping and flow constraints. However, on-line material balance calculation could offer a reliable alternative to flow rate sensing. This paper describes an on-line material balance software package as applied to a copper flotation circuit for mass flow rate estimation mainly based on the output of an x-ray fluorescence onstream analyser. Rule-based procedures for the management of the main calculation modules are designed and integrated to a Comdale expert system. Attempts to diagnose the flotation process from mass flow rate data are also discussed.INTRODUCTIONThe need for improved process diagnosis, control and optimisation has become more evident for the mineral processing industry in the last decade. Therefore, new process variables need to be inferred or measured particularly in highly multivariable processes such as flotation. This process is subject to a wide variety of disturbances mainly generated by frequent and sometimes abrupt changes in physical and chemical characteristics of the ore and due to some irregularities in manual process operating procedures.A flotation circuit scheme is always a complex network counting more than two dozens of slurry streams. Information about those streams (%solids, metal content analysis, and flow rates) are important for process diagnosis, performance evaluation control and optimization (1,3).On-line sensing instruments such as x-ray fluorescence (XRF) on-stream analysers (OSA), gamma density gauges and electromagnetic flowmeters have been developed for the measurement of those variables. Unlike the other variables, stream flow rates could be determined by different ways:"

Jan 1, 2000

By Joe Shoemaker

Automated Spot Generation ? No Operators below the Highwall ? No Operator Wear and Tear ? Reduced Swing Time ? Single and Double Sided Loading ? Minimized Bench Width

Aug 1, 2013

By Lashley Harvey

Dado que la colonización de América Latina presentaba problemas en la adquisición y población de valles norteamericanos del Missouri y el Mississippi, el desarrollo de las cuencas del Amazonas, el Orinoco y el Plata tuvo que esperar hasta el siglo XX, puesto que entonces los conocimientos de ingeniería más avanzados hicieron posible utilizar al máximo esos tres sistemas fluviales. En esta perspectiva, el texto plantea la administración de cuencas como una forma de aprovechamiento de los ríos para múltiples objetivos y de conservación del agua.

May 1, 1976

By R. M. Goldhoff, J. W. Spretnak, R. Speiser

IT has been observed by Grange and Garvey' that the homogenization of boron-treated steels could lead to complete elimination of the hardenability effect caused by boron. The experimental conditions leading to this conclusion involved the heating of steel specimens with and without boron at 2350°F for 24 hr. To prevent oxidation and decarburization, the specimens were encapsulated under vacuum in silica tubes. This observation of permanent deterioration of boron effect was noted in both a 0.63 pct plain carbon steel and a 0.25 pct C low alloy steel, both of which had been treated with ferroboron and homogenized at 2350°F for 24 hr. In another series of boron-treated steels which had been homogenized for shorter times, the effect was to reduce, but not completely eliminate, the boron effect. Under these circumstances, it was presumed that longer heating times would cause permanent deterioration of the boron effect in this series of steels also. Since the characteristic grain boundary constituent could not be formed in any of these steels after homogenization, it was concluded that possibly boron was being converted into an ineffective form through chemical combination resulting from prolonged heating at high temperatures. Assuming the validity of this observation, a series of experiments to establish the relationship between temperature of homogenization and kinetics of deterioration was contemplated. Initially an attempt was made to reproduce the results just described. For this purpose commercial lots of AISI 8640 and AISI 86B40 steels were used. The analyses of these steels appear in Table I. Hardenability evaluation was on the basis of the hardness of normalized sections. Grange and Garvey' pointed out that these steels are air hardening to some extent and such a technique can be used. For these tests the specimens were held for 20 min in a salt bath at 1600°F and then cooled in still air. Several evacuated silica capsules containing pairs of the test steels were made up and heated for 24 hr at 2350°F. A number of failures occurred among these capsules, but evaluation of the specimens successfully treated indicated a complete deterioration of the boron effect. However, examination of the surface of the treated specimens showed that some reaction, probably with the silica tube, had taken place, since none of the specimens was bright. One further test was made at 2350°F for 12 hr, using a pair of specimens wrapped in tantalum foil prior to encapsulation. These specimens appeared bright after treatment, and their hardenability evaluation showed that no deterioration had taken place. Since these steels are extremely sensitive to de-boronization at high temperatures and particularly at long times of holding, the experimental observations raised some doubt as to the real occurrence of the permanent deterioration effect. To resolve this question an experiment was undertaken in which the high temperature portion of the treatment was completed in vacuum. For this purpose a molybdenum wound resistance furnace capable of maintaining good vacuum was used. All the pertinent accessories to this furnace were machined from molybdenum stock in order to withstand the high temperature involved in the experiment. With this equipment a temperature of 2400 °F was obtained and held under a pressure of 5x10-" mm Hg for 24 hr. A specimen of each of the two test steels was suspended in the furnace and both were heated simultaneously. Temperature was measured with a standardized Pt—Pt-13 pct Rh thermocouple, whose millivoltage at 2400°F was extrapolated from the standardization equation, good up to 2200°F. The complete evaluation of these specimens is shown in Table 11. The hardness values attained by each steel after normalizing, both before and after the prolonged high temperature treatment, remain the same. A microscopic study of the decomposition products present in the microstructures of specimens at various points in the heat treatment correlated with the hardness values observed. It seems that no permanent loss of boron hardenability effect occurs, at least in these Grainal-treated steels, when deboronization is circumvented. Acknowledgments This work was conducted under the sponsorship of the Aeronautical Research Laboratory, Wright Air Development Center, under Contract No. AF 18(600)-94, and their support and permission to publish is gratefully acknowledged. A note of thanks is also extended to the Republic Steel Corp. for supplying the materials used in the work. References ' R. A. Grange and T. M. Garvey: Factors Affecting the Harden-ability of Boron Treated Steels. Tro.ns. ASM, 1946, vol. 37, p. 136.

Jan 1, 1957

By Wouter Hartman

Xuandong Coal Mine is mining coal in one of the most challenging underground environments in the world. This work has found that it is not only challenging but it also has the composition for some interesting rock mechanics and ground control conditions. The paper highlights the extreme mining and rock mass behavior conditions encountered when mining coal at 900 m below surface. It was found that the ground control environment associated with geological weakness, low coal material strength and stiffness, was reasonably well controlled; however, the chain pillar geometry and design did not take these geological weaknesses into consideration. Some of the chain pillars employed were quite large, which resulted in floor punching and secondary floor heave, which causes extreme difficulty for production. No barrier pillar has been employed except for the center 164-m-wide main headings pillar with a w/h ratio in excess of 40. After assessing the location and geometry of a 200-m-thick dolerite sill overlaying the coal measures, we found the probability of it breaking up into to smaller fragments and producing a larger goaf to be low. Therefore, the influence of the dolerite sill on chain pillar loading is considered small compared to the low coal, immediate floor and roof rockmass strength. It is further recognized that horizontal stresses could be locked up within the dolerite sill, which would likely result in regional bending that would be distributed through the chain pillars. This has, to some extent, already occurred, and the effects have been seen and felt through excessive floor heave, pillar punching, and coal bumps (seismicity). We?ve also found that there was a need to employ basic rock mechanics principals in assessing the stability of future multiple seam mining layouts.

Jan 1, 2012

By Thomas G. Murdock

The possible contribution of an improved mineral economy to the further advancement of the lesser developed regions of the world is a vital consideration today. Many of the newly independent countries recognize the problems and the challenge involved in orderly development of mineral resources. Some countries are inventorying resources, planning development, and encouraging local and foreign participation. The Malagasy Republic, composed of the island of Madagascar and the immediately adjacent islands, formerly the French Overseas Territory of Madagascar, is one of the members of the French Community which achieved independence in 1960. It is making real progress towards improving its mineral economy, an effort particularly remarkable considering the generally unfavorable geographic location of the area with respect to world markets and what is, after all, a comparatively sparse economic mineralization in the light of discoveries to date. Most of the development of the Malagasy econorny before independence was fostered by French private enterprise, although the State participated in some ventures. Since independence, the Government has encouraged private investment from a variety of sources through favorable legislation and has indicated that legitimate investment projects that will further advance social and economic programs will be welcome.

Jan 1, 1963

By Robert V. Berryhill

Reconnaissance studies of beach deposits along approximately 220 miles of the shoreline of Bristol Bay, Alaska, were made to determine if more detailed investigations were warranted. In addition to preliminary mapping of the deposits, samples were obtained from auger borings spaced at 1-mile intervals in key areas; shovel samples were collected to supplement the borings. Most samples were roughly concentrated in the field; magnetic separation tests, petrographic analyses, and determinations for radiometric equivalent uranium, gold, platinum, iron, and titanium were made in the Bureau of Mines laboratory at Juneau, Alaska. Spot samples from some beaches along the shores of the Alaska Peninsula indicate small deposits containing up to 10 percent recoverable titaniferous magnetite; some larger deposits were indicated to contain from 1 to 2 percent total heavy metal, principally as titaniferous magnetite. Significant amounts of other commercial minerals were not detected.

Jan 1, 1963

By James T. McCartney, Joseph D. Davis

For more than 10 years coke-oven technologists have been investigating the expanding properties of coal on a scale larger than that afforded by laboratory test tubes. Koppers 4/ was among the first to realize that coals can not be differentiated satisfactorily with respect to expansion in coke ovens by the simpler test-tube methods; in his first method 80 grains of fine coal were coked in a cylinder heated from the bottom, so that the zone of fusion (plastic layer) advanced from the bottom to the top. The scale of test was too small; it has been modified by other investigators, but without significant improvement in practical application of the results. Somewhat later Koppers and Jendne 5/ experimented with a small-scale coke even, one wall of which was movable, in which the layer-coking in a coke oven could be simulated closely. This oven was heated from both sides. Their results with this oven showed a peak in the time-pressure curves near the end of the coking, period when the two plastic layers, advancing from opposite walls, meet. They also found that although the smaller oven was heated from one side only and did not show the Pressure peak characteristic of two-sided heating, it still gave results entirely too high. Russell built an oven similar to the movable-wall oven of Koppers and Jenkner and compared results obtained in it on Beckley expanding coal with these obtained on the some coal in the Altieri 7/ small-scale apparatus. Both tests were conducted at the same constant pressure, but heating was from two sides in Russell's oven and from one side in the Altieri tester. Russell found that the two types of test gave comparable results under constant pressure conditions even though the heating procedures were quite different. He showed later, however, that a "borderline" coal 8/ that contracted in the Altieri tester at constant pressure developed a peak pressure of 4 pounds per square inch in the movable-wall oven heated from both sides at constant volume. He concluded from this that testing at constant volume gave results more accurately indicative of dangerous expansion tendencies than those at constant pressure. He also found that heating from both sides in this oven gave higher pressure than heating from one side only.

May 1, 1942

By Aldo Henrique de Almeida Barbosa

Os modelos de tratamento de galvannealing, com encharque isotérmico após o aquecimento indutivo, permitem otimizar o aporte térmico para a formação de compostos intermetálicos Fe-Zn, o que contribui significativamente para a obtenção de revestimentos galvannealed-GA de elevada qualidade. Nesse estudo foi avaliado o efeito das condições de galvannealing na formação do revestimento GA sobre aços bake hardenable-BH. Foram realizadas, em escala de laboratório, simulações variandose o modelo de galvannealing, com ciclos isotérmicos e resfriamento imediatamente após o aquecimento indutivo, a temperatura de aquecimento, entre 525°C e 570°C, e o tempo de encharque, até 20 segundos. Em todas as simulações, além dos ciclos completos foram realizadas, também, interrupções do tratamento ao longo da etapa de encharque, através de resfriamento brusco das amostras, com o objetivo de se avaliar a microestrutura do revestimento ao longo de todo o tratamento. Para a caracterização dos revestimentos foram realizadas análises de composição química, microestrutura, perfil de composição ao longo da camada e de aderência. Os resultados permitiram determinar as características da formação do revestimento GA sobre os aços BH e estabelecer condições de galvannealing para o processamento desses aços, de forma a obter microestruturas otimizadas para as aplicações mais exigentes.

Aug 16, 2017

By Thomas G. Murdock

The possible contribution of an improved mineral economy to the further advancement of the lesser developed regions of the world is a vital consideration today. Many of the newly independent countries recognize the problems and the challenge involved in orderly development of mineral resources. Some countries are inventorying resources, planning development, and encouraging local and foreign participation. The Malagasy Republic, composed of the island of Madagascar and the immediately adjacent islands, formerly the French Overseas Territory of Madagascar, is one of the members of the French Community which achieved independence in 1960. It is making real progress towards improving its mineral economy, an effort particularly remarkable considering the generally unfavorable geographic location of the area with respect to world markets and what is, after all, a comparatively sparse-economic mineralization in the light of discoveries to date. Most of the development of the Malagasy economy before independence was fostered by French private enterprise, although the State participated in some ventures. Since independence, the Government has encouraged private investment from a variety of sources through favorable legislation and has indicated that legitimate investment projects that will further advance social and economic programs will be welcome.

Jan 1, 1963

By D. Grabowski, Z. Pokryszka

A study carried out in the iron basin of Lorraine (North-East of France) highlighted the existence of under-oxygenated and noxious gas emissions (carbon dioxide, radon…) in vast built-up areas related to former mine workings. Site investigations showed that the gas flow was mainly due to natural thermal air circulation between old mines and external atmosphere. The main hazards associated with this flow of gas and its potential accumulation in confined volumes in buildings are asphyxiation and intoxication. A further study is in progress in order to better understand the origin of the gas generation within the old iron mine workings. Following the first hypothesis, the carbon dioxide emission is mainly due to the specific hydro-geo-chemical process associating the pyrite oxidation with the acid dissolution of carbonates. KEY-WORDS : gas, emission, iron mine, pyrite.

Jan 1, 2003

By D. Bessinger, J. Nell

The electrical conductivity of rutile was optimised as a function of time, temperature and gas composition. These optimised conditions were used to treat rutile/zircon feed prep concentrate samples from a South African heavy minerals producer, prior to electrostatic separation. Enhanced separation between rutile and zircon was obtained when compared to untreated samples. Samples treated in a hydrogen atmosphere and cooled in nitrogen showed the best separation when passed through a high tension electrostatic separator using conditions of high sample temperature and high relative humidity.

Jan 1, 2005

By Thomas Gregor, Brian Garrod

As the popularity of precast concrete segmental linings for tunnels is growing in North America, some problems related to grouting of, and near, these linings are starting to appear. The installation of a segmental lining behind a TBM requires that the annular space around the lining be quickly filled with grout to prevent collapse of the ground. In practice, the filling of the annulus is frequently delayed and takes place a distance behind the machine typically via grout ports centrally located in the segments. If partial collapse of the annulus has occurred, it may become necessary to use higher grouting pressures in an attempt to distribute the grout. There have been several occasions where these increased pressures have caused damage to the tunnel linings. Similarly, compaction grouting adjacent to a tunnel lining can cause damage. This paper quantifies the effects of such grouting on a typical precast lining.

Jan 1, 2005

The epithermal Au-Ag deposits of the Hauraki Goldfield have formed in the convergent plate margin setting of the Coromandel Volcanic Zone (CVZ). The deposits form as siliceous lodes in the upper parts of geothermal systems associated with andesitic and rhyolitic volcanism. Two types of low sulphidation epithermal mineralisation are recognised in these volcanic terranes. Vein deposits within the rhyolitic terrane in the east and south of the CVZ (Whitianga Province) are typified by Chalcedonic Silica-Adularia-Illite type mineralisation. The veins are hosted by both rhyolite-dacite volcanic rocks and the underlying andesitic basement. The mineralisation formed by episodic violent decompressional boiling of deeply circulating meteoric water, with some magmatic fluid contribution; this boiling was associated with hydraulic fracturing and hydrothermal eruptions in geothermal systems where the piezometric surface of the deep geothermal reservoir lay near-surface. Such episodic boiling provides chalcedonic veining, banding and brecciation textures, adularia stability, bladed calcite, and extreme loss of H2S gas from the fluid to cause major gold deposition.   Crystalline Quartz-Illite-(Adularia-Kaolinite) type mineralisation is widespread in the andesitic terrane forming the northern and western portions of the CVZ (Kuaotunu Province). There is a spatial association with weak mineralisation of the high sulphidation (Vuggy Silica-Alunite-Kaolinite-Illite) epithermal type and porphyry eu-Au type. Crystalline Quartz mineralisation is probably formed by the mixing of shallow acidic groundwaters with the ascending deep geothermal fluid in geothermal systems beneath andesitic stratovolcanoes. The piezometric surface to the deep geothermal reservoir in these systems is likely to lie at considerable depth, with acidic gases rising from the geothermal reservoir condensing within the overlying vadose zone. The cooling effect, oxidation and pH decrease accompanying mixing apparently overcomes the dilution effect, and results in quartz deposition, illite (and locally kaolinite) alteration, and precipitation of gold. A high level of base-metal sulphide precipitation also enhances gold deposition. Violent boiling of the mixing fluids may occur at local structural dilation sites, producing high grade "bonanza" gold mineralisation.

Jan 1, 1991

By J. T. Popp

This Bureau of Mines study reviews the geological factors that affect methane in the Beckley coalbed in southern West Virginia, including overburden, coalbed structure, type of and changes in lithology above and below the Beckley coalbed, and presence of fractures in the coal and rock adjacent to the Beckley. Depending on the depth, the Beckley coalbed emits from 216 to 520 ft3 of methane per ton of coal mined, and the Bureau estimates that methane emission in a deep, extensively developed mine in this area may exceed 3,000 ft3 per day per ton of coal mined. Average face cleat and butt cleat trends in the Beckley coalbed measured underground are N 33° W and N 53° E, respectively. Close cleat spacing con¬tributes to the friable nature of the Beckley and provides easy movement for methane and water. Because rider coals, splits, and carbonaceous shales may contribute methane to mine emissions, predictions of methane emission based on gas content of the Beckley coalbed alone may be conservative. Beckley coalbed reserves in the study area are 234 million tons. The gas content of the Beckley coalbed averages 407 ft3/ton, and the coalbed gas reserves are 108 billion ft3.

Jan 1, 1976

By Adam Wright

"Les Mines Selbaie have been producing copper and zinc concentrates from the A-1 ore zone since 1986. This paper reviews major developments in flotation practice over that period. Firstly, ore blending strategies for Selbaie's non-homogeneous polymetallic ore are discussed. The evolution of reagent use is then reviewed, focussing on copper collector trials. A description of Selbaie's flotation columns follows. Finally, past and future developments for process control are outlined.Depuis 1986, Les Mines Selbaie produisent du concentré de cuivre et de zinc provenant de la zone A-1. Cette conférence présente !es développements majeurs en flottation qui ont eu lieu depuis ce temps. Premièrement, la stratégie du mélange de minerai non homogène polymétallique est présentée. L'évolution des réactifs utilises est démontrée, particulièrement !es collecteurs de cuivre. Par la suite !es colonnes de flottation sont presénteés et finalement !es développements futurs ainsi que ceux qui ont eu lieu dans le contrille de procédé sont expliqués.1.0 INTRODUCTIONLes Mines Selbaie, wholly owned by Billiton Metals Canada Inc., is currently mining and processing ore from a polymetallic surface deposit located 288 km northwest of Val D'or, Quebec (fig. 1). The mine produces copper concentrates containing gold and silver as well as zinc concentrates containing silver. 8000 dmt/day of ore is crushed and ground to 80% passing 49 µm, prior to processing by conventional copper/zinc differential flotation. The flotation circuits consist of both conventional and column cells (fig. 2). Detailed descriptions of the mill are available elsewhere in the literature (8,9)."

Jan 1, 1995

GOLD has played a part in the development of Australia. The total yield exceeds SIX hundred million pounds sterling, while the glamour of gold-mining and the unfailing demand for the product have enhanced its influence. The production is still considerable, but the yield is less than one-quarter of that twenty years previously, while the number of men employed has dropped from 70,000 to 11,000. Not only has there been a marked decline in production, but it is anticipated that thisdecline will continue, and continue more markedly. It is therefore desirable to ascertain the causes of the decline and inquire into means for diminishing or preventing it.The problem under discussion is far from being only local. Finlay states: The grand feature of the history of the business has been the progress of an economic cycle unfavourable to gold milling. The USA yield fell from $101,000,000 to $44,000,000.South Afriea has for some time produced one-half of the world's gold; yet in the Mining and Scientific Press of 11th February, IH22, General Smuts is quoted as saying that if the premium disappeared entirely 24 out of 34 mines would shut down. The solution, however, might be either general eg, a great advance in the metallurgy of gold; or local eg, a bonus; but before discussing any of the proposed solutions it will be advantageous to review the situation.STATISTICS OF THE PAST AND PRESENT PRODUCTION OF THE WORLD AND OF AUSTRALIAThe inquirer soon finds that there is a good deal of uncertainty, and that much care is needed in collating figures. In some cases a considerable part of the output is not officially reported, and returns...

Jan 1, 1924

By Soner Top

In this study, a process to separate manganese and iron from manganiferous iron ores by reductive acid leaching followed by magnetic separation was conceived and experimentally tested. In the leaching process, sulfuric acid was used as lixiviant and oxalic acid was used as reductant. The experimental results showed that the manganese and iron separation was optimum when the concentration of the sulfuric acid and oxalic acid were 0.75 M and 30 g/L, respectively, at a temperature of 80 °C, a solid/ liquid ratio of 67 g/L, stirring speed of 400 rpm, and leaching duration of 60 min. Under this condition, 90.49% and 6.78% of Mn and Fe were dissolved, respectively, from the ore sample with a size fraction of − 106 μm. It was determined that the leaching of manganese from the ores was a second-order reaction with an activation energy (Ea) of 53.38 kJ/mol. The leaching residues obtained under the optimum condition were subjected to high-intensity wet magnetic separation tests to recover the remaining iron content. This separation process produced a concentrate containing 56.20% Fe and 1.79% Mn with iron and manganese recoveries of 56.83% and 66.73%, respectively. A magnetic separation test from an unleached ore sample was also carried out as a benchmark. To the best of our knowledge, this is the first time that a magnetic separation process was used to a residue obtained from reductive acid leaching of manganiferous iron ores to recover iron.

By Soner Top

In this study, a process to separate manganese and iron from manganiferous iron ores by reductive acid leaching followed by magnetic separation was conceived and experimentally tested. In the leaching process, sulfuric acid was used as lixiviant and oxalic acid was used as reductant. The experimental results showed that the manganese and iron separation was optimum when the concentration of the sulfuric acid and oxalic acid were 0.75 M and 30 g/L, respectively, at a temperature of 80 °C, a solid/ liquid ratio of 67 g/L, stirring speed of 400 rpm, and leaching duration of 60 min. Under this condition, 90.49% and 6.78% of Mn and Fe were dissolved, respectively, from the ore sample with a size fraction of − 106 μm. It was determined that the leaching of manganese from the ores was a second-order reaction with an activation energy (Ea) of 53.38 kJ/mol. The leaching residues obtained under the optimum condition were subjected to high-intensity wet magnetic separation tests to recover the remaining iron content. This separation process produced a concentrate containing 56.20% Fe and 1.79% Mn with iron and manganese recoveries of 56.83% and 66.73%, respectively. A magnetic separation test from an unleached ore sample was also carried out as a benchmark. To the best of our knowledge, this is the first time that a magnetic separation process was used to a residue obtained from reductive acid leaching of manganiferous iron ores to recover iron.