Search Documents

By Mehdi Asadi, Heinz Palkowski

"In recent years, the increased demand for advanced high-strength steels (AHSS) mainly had been driven by the need of the automotive industry to reduce weight and to improve safety. Beside good ductility and high strength, those steels have a high bake hardening (BH) effect, giving additional contribution to the strength of structural parts, subjected to the paint baking process. In this paper we concentrate results gained for hot rolled dual phase (DP) steels.For the simulation of changing process conditions within the final hot rolling the specimens were hot deformed using different schedules of temperatures and reductions, selected according to the non-recrystallization temperature (TnRX). It was possible to refine the DP steel structure by control-ling the deformation temperature and the amount of strain below TnRX during the thermo-mechanical controlled processing (TMCP). This structure refinement resulted in an improvement of the strength and BH behaviour. A wide spectrum of mechanical properties could be obtained depending on the different hot deformation schedules. The best strength and BH levels were recorded for the deformation below TnRX at the highest amount of strain.IntroductionDP steels are characterized by a good formability, high strength and a good compromise between strength and ductility [1]. Moreover, the DP steels exhibit a continuous yielding behaviour, low yield point and a high strain-hardening coefficient [2]. Furthermore, the DP steels often show a large potential for bake hardening (BH). BH refers to the increase in yield strength as a result of the paint baking treatment of the shaped auto-body parts. The primary mechanism that causes the additional strengthening is the immobilization of dislocations by the segregation of interstitial atoms, known as classical static strain aging [3]. The increase of strength thus achieved allows a further reduction of sheet thickness and improves the crash safety and the dent resistance. The BH of special steel qualities is technically used in DP, where e.g. the increase in strength is realized in the final heat treatment [4]. Previous own investigations [5-6] stated that the BH effect of DP is much stronger than that one for conventional BH steels."

Jan 1, 2012

By David R. Brosnahan

Increased Cu grades due to chalcopyrite-rich ore from The Doe Run Company's new Casteel Mine prompted a program to increase Cu recovery. Preliminary tests indicated that prohibitive quantities of FeS2 float with chalcopyrite. Point counting of mill stream samples showed that locking was not a major problem, although grinding to finer particle size enhanced the floatability of both chalcopyrite and marcasite. Backscattered electron images and microprobe analyses of FeSz minerals revealed the presence of Pb which appears to occur as solid solution in marcasite, and as a sub-micron particulate Pb phase in pyrite.

Jan 1, 1987

By Kimio Ilagaki

The distribution ratios of Ag, Pb, As, Sb and Bi for the Cu2S-FeS or Ni3S2-FeS matte I FeOx-SiOl, FeOx-Si02-CaO or FeOx-CaO slag equilibration in a MgO crucible were determined experimentally at 1523 ~1573K under controlled partial pressures of S2 and 02 at given PS02 of 10.1,50.7 and 101.3 kPa(O.I, 0.5 and I atm), and the observed dependency of distribution ratio on the matte grade, S02 pressure and slag basicity were analyzed on the basis of thermodynamics.

Jan 1, 2003

By Richard J. Abitz

Thennodynamic geochemical models have been applied to assess the relative effectiveness of a variety of reagents added to aqueous waste streams for the removal of radioactive elements. Two aqueous waste streams were examined: effluent derived from the processing of uranium ore and irradiated uranium fuel rods. Simulations of the treatment train were performed to estimate the mass of reagents needed per kilogram of solution, identify pH regions corresponding to solubility minimums, and predict the identity and quantity of precipitated solids. Results generated by the simulations include figures that chart the chemical evolution of the waste stream as reagents are added and summary tables that list mass balances for all reagents and radioactive elements of concern. Model results were used to set initial reagent levels for the treatment trains, minimizing the number of bench-scale tests required to bring the treatment train up to full-scale operation. Additionally, presentation of modeling results at public meetings helps to establish good faith between the federal government, industry, concerned citizens, and media groups.

Jan 1, 1996

By Huimin Lu, Min Li, Jinghua Zou

"Zeolitic imidazolate frameworks (ZIFs) are new type of porous materials, form inerratic polyhedral in three-dimensional with large cages and small apertures, and appear structural diversity. Their hole size can be adjusted. These materials have high selective adsorption capacity to carbon dioxide. In this paper, zeolitic imidazolate frameworks were synthesized by solvothermal synthesis method with dimethylformamide (DMF) as solvent and structuredirecting agent, divalent metallic ions as cation, and imidazole as ligand. The crystals were characterized with XRD, SEM for their crystal structures and physical properties, the adsorption of the crystals for carbon dioxide was also tested, and the result suggests that these porous materials have a capacity of 1.35ml/g for storing carbon dioxide at 273 Kelvin under ambient pressure.IntroductionGlobal warming caused by the increase of carbon dioxide in the atmosphere has become one of the main environment problems, contemporary research has focused on ways to slow or stop this trend. CO2 capture has attracted attention due to the potential to trap and sequester large amounts of CO2 from concentrated sources such as power plants [1]. Traditional technologies in capturing CO2 include absorption by aqueous amines [2]. However, utilization of this process is energy intensive and expensive. Carbon dioxide storage materials investigated so far can be divided into two categories: chemical storage adsorbents and physical storage media [3]. The first kind of materials can chemically adsorb carbon dioxide within their structures and need thermal energy to release the adsorbed carbon dioxide. The examples of the chemical adsorbents include aqueous amines, gas-hyperbranched aminosilicas [4]. The physical adsorbents store carbon dioxide by physical adsorption of carbon dioxide at elevated pressure and release the adsorbed carbon dioxide at low pressure. The physical adsorbents that have been investigated for carbon dioxide storage include zeolites, carbonaceous materials and other porous materials. Until recently, a new type of microporous material, known as zeolitic imidazolate frameworks (ZIFs), has been reported as promising adsorbents for carbon dioxide storage [5 ~ 10]."

Jan 1, 2010

By G. Van Weert

Refractory gold ores and auriferous concentrates containing silver tend to form refractory silver jarosites during pressure oxidation. Earlier work with pure Ag2S has shown that the addition of iodine species to the autoclave feed yields cyanide soluble iodargyrite (Agl) instead. Near complete silver extractions from the autoclave product were obtained at a I-/Ag+ ratio of 5 or more. This paper reports on the pressure oxidation and cyanide leaching of two industrial refractory (arseno) pyritic silver-bearing concentrates: 1. from Peru (sulphosalts) and 2. from the USA (pyrite, with acanthite occlusions). While using a I-/Ag+ mol ratio of only 1 in the feed, it has been possible to obtain 98 and 97% Ag extraction from the two autoclave products by cyanide leaching, respectively. This compares to 11 and 54% Ag extraction from the as-received concentrates and 4 and 15% Ag extraction, respectively, after pressure oxidation without KI present. The results of the testwork are discussed in terms of concentrate mineralogy and pressure oxidation conditions.

Jan 1, 1994

By S. Stoyanov, M. Cross

"Silicon components containing transistor circuitry are at the heart of electronic products such as computers, mobile phones, etc. These components are connected to printed circuit boards (PCB's) using solder material that acts as the conductor for both electricity and heat. During the lifetime of a product it will undergo many thermal cycles where the chip becomes hot during product operation and then cools when the product is switched off. At the product design stage engineers undertake thermo-mechanical simulations to predict the thermal stress in the solder joints due to this thermal cycle and to ensure that the stress magnitude will not result in early fatigue-type failure. The design engineer's aim is to identify component parameters which ensure that the solder will survive beyond a certain number of thermal cycles.The aim of integrating computational mechanics and optimization tools together is to speed up dramatically the design process. From viewpoint of a design engineer in the electronics manufacturing sector, these tools can be used to quickly estimate key design parameters (i.e. material properties, product dimensions, etc) that will guarantee the required product performance. In this paper a modeling approach coupling computational mechanics techniques with numerical optimization is presented and demonstrated. The integrated modeling framework is obtained by coupling the multi-physics framework - PHYSICA - with the design optimisation tool- VisuaLDOC. Thermo-mechanical simulations are presented that predict the creep strains in solder material. Different numerical optimization procedures: Direct and Response Surface based optimization plus Design of Experiments, are tested as a part of this modeling framework."

Jan 1, 2001

By K. Osseo-Asare

Third phase formation, the separation of a solvent extraction organic phase into two liquids, is generally attributed to the limited solubility of the extracted complexes in the hydrocarbon diluents. Much of the research on third phase fomiation, therefore, emphasizes experiments designed to establish the stoichiometry of the species responsible for the limited solubility. This work offers a different approach, based on the recognition that the solvent extraction third phase, in fact, corresponds to the middle phase in a microemulsion fluid system. Using the tri-n-butylphosphate (TBP)-diluent-water-electrolyte system as a model system, current concepts of microemulsion phase behavior are utilized to develop a general framework for interpreting and predicting the patterns of phase behavior in solvent extraction systems.

Jan 1, 1999

By Wilhelm Brandstätter, Johannes Steiner, Alois Triessnig, Christian Redl

"The results of numerical simulations of bubble detachment from an orifice in a horizontal plate submerged in liquid are presented. The bubbles are created by forcing gas through this orifice into stagnant liquid. The simulations are performed with a two-dimensional incompressible Lattice Boltzmann (LB) scheme. In previous works the same problem was investigated by two-phase simulations in which surface tension effects were considered by an interaction potential formulation between the phases. In contrast, in the present work a volume of fluid (VOF) model consisting of a carrier fluid and a passively advected scalar function for the calculation of gravitational and surface tension forces, respectively, is used. The aims of this study are to examine the applicability of the one-phase LB method to the numerical analysis of bubble formation and to verify the theoretical and experimental predictions of the dependencies of the departure diameter on gravitational forces, surface forces and wettability effects. To this purpose the simulations were performed at different values of gravitational acceleration g, surface tension coefficient s and contact angle ß. Nonlinear fits to the data yield functional dependencies which are in good agreement with the predictions. IntroductionBubble formation behavior is an extensively studied subject, especially in chemical engineering, power industries and metallurgical processing. Knowledge of the underlying physics of bubble motion is, for example, required for the design of chemical reaction towers and agitation tanks. Another important application is the argon gas injection through the wall of the tundish nozzle into liquid steel stream to deter clogging with solid inclusions. Argon bubble motion and its effect on flow depends greatly on different parameters, e.g. gas flow rate and size of the bubbles. Thus, if these bubbles are not managed properly, they can become encapsulated upon solidification and result in undesirable impurities in the material [1, 2]."

Jan 1, 2004

By Herman Wotruba

Mercury emissions and other environmental impacts in small-scale gold mining are a world-wide problem. "Clean" or better: "Cleaner" technologies have -apart from being environmentally sound -to guarantee a higher income and better working conditions for the miners in order to have a chance for long-term acceptance. In small scale primary gold mining in several South American countries, a number of techniques have been adapted and improved so that they not only were accepted due to their efficiency and easy handling, but they could also significantly lower mercury emissions.

Jan 1, 2003

By Pengfu Tan

NiModel, a thermodynamic model, database and computer program, has been developed to predict the distribution behavior of Ni, Cu, Co, Fe, S, O, As, Sb and Bi, and heat balance in the nickel pyrometallurgical processes such as Outokumpu flash smelting, Outokumpu direct high-grade matte smelting, INCO flash smelting, and Peirce-Smith converting processes. In this model, as much as 16 elements (Ni, Cu, Co, Fe, As, Sb, Bi, S, O, Al, Ca, Mg, Si, N, C and H) are considered. The compositions of matte, slag and gaseous phases, and heat balance are calculated using the thermodynamic data and the activity coefficients of the components derived from the experimental data. The model predictions were compared with the known industrial data from Kalgoorlie Nickel Smelter in Australia, Outokumpu Harjavalta Nickel Smelter in Finland and INCO Metals Company in Canada, and an excellent agreement was obtained. In this paper, the applications of NiModel in the nickel pyrometallurgical industries have been presented. NiModel has been used by Jinchuan Group Limited in China.

Jan 1, 2004

By cheng Peng-fei, TANG Hai-yan, guo Xiao-chen, LI Jing-she, Liang Yong-cang, Zhao Baojun

The origin and evolution of non-metallic inclusions for Al-killed casing steel during EAF-LFVD- CC process were studied by industrial tracer experiments. The formations of Al2O3 and MgO·Al2O3 micro- and macro-inclusions from ladle slag were analyzed by theoretical calculations. The results show that micro-inclusions were formed during deoxidation and temperature decreasing in the process of casting, most of the macro-inclusions come from entrapped ladle and mold slags. In addition, most of the Al2O3 formed were modified into 12CaO·7Al2O3 and 3CaO·Al2O3 inclusions which are liquid at steelmaking temperature. MnS cannot be fully modified to CaS and it was only wrapped outside the alumina or calcium aluminate in the form of (Ca,Mn)S with the amount of Ca-Si wire fed during the test.

Jan 1, 2016

By A. S. Rao

In the original roast-leach-electrowin (RLE) circuit at the Chambishi Cobalt Plant, commissioned in 1978, the separation of nickel and zinc from cobalt in aqueous streams was achieved by successive stages of precipitation using lime. However, this technique was not able to meet the increasingly stringent metal quality requirements of customers whilst maintaining acceptable process recoveries. Intensive process development work was carried out and, in July 1988, an ion exchange circuit for nickel removal was commissioned using DOW XFS 4195 resin and for the first time Z.C.C.M. produced high purity cobalt metal containing less than 0.10% nickel. Following further work, a solvent extraction circuit for zinc removal, using DZEHPA, was commissioned in February 1991 in order to enhance cobalt recovery by reducing co-precipitated cobalt losses. This paper outlines the process development, design, commissioning and subsequent operation of these nickel ion exchange and zinc solvent extraction circuits.

Jan 1, 1993

By Thomas E. P. Wechsler

The limiting factor for most pyro-metallurgical processes in secondary cop- per melting is the time required to heat and melt the product. American Combustion's proprietary PYRETRON variable £uel/air/oxygen combustion system improves the throughput of existing scrap melting and heating furnaces for copper and copper alloy production by increasing the rate of heat transfer from the flame to the product. The increased productivity and energy savings obtained from this technology can result in sizable reductions in operating costs for smelting operations.

Jan 1, 1991

By T. K. Bundtzen

Placer gold in the Iditarod and Innoko mining camps of western Alaska is derived from a suite of comagmatic, Late Cretaceous to Early Tertiary, alkali-calcic, meta-aluminous. volcanic-plutonic complexes and peralumi-nous rhyolite sills that intrude Mesozoic flysch. Heavy-mineral concentrates from 42 mining operations and streams draining known mineralized areas in the igneous complexes contain placer gold and a variety of ore minerals derived from epithermal to hypothermal conditions of formation. The minerals include cassiterite, ilmenorutile, samarskite, cinnabar, scheelite, chromite, stibnite, silver sulfosalts, monazite, and zircon. Results of the study show that 1) cinnabar. stibnite, and quartz formed with the bulk of the placer gold in an epithermal lode environment, 2) chromite appears to have originated in mafic phases of monzonite plutons and alkalic basalts, and 3) niobium-tin-tungsten-uranium-silver values may have been derived from stockwork accumulations in cupolas of monzonite plutons.

Jan 1, 1987

By M. J. Collins

Direct pressure leaching of zinc sulphide concentrates was started? commercially in October 1980. Continuing research and development studies at Sherritt and feasibility studies for a number of clients have defined various pressure leach configurations for integrattons with existing roast- 1 each operations and for grass roots plants. Existing and potential applications of zinc pressure leaching are discussed.

Jan 1, 1990

By Min Chen, Lei Xu

Sintering behavior and performance of high alumina refractory based on the ternary subsystem MgAl2O4-CaAl4O7-CaAl12O19 were investigated using ZrO2 as an additive up to 8 wt.% by solid state reaction sintering. It was found that the added ZrO2 could dissolve in the CA6 grains in the form of a solid solution, which enhanced the isotropic growth of CA6 grains and then improved the sintering. As a result, the densification process was improved and areas with enrichment of ZrO2 showed a more compact structure. With further increase of ZrO2 addition, tetragonal ZrO2 were found to locate in the grain boundaries for exceeding the solid solubility limit, which enhanced the thermal shock resistance, indicating that addition of ZrO2 exhibited a positive effect on sintering behavior and performance of this refractory. In addition, it is considered that the optimal amount of ZrO2 addition was about 4% considering the performance together with the cost.

Jan 1, 2015

By Rodney J. Ishak

The reduction of Mn3O4 to MnO has been investigated in a thermobalance apparatus, The charge was composed of manganese ore (decomposed by heating/calcination or pre-reduction to mainly Mn3O4) and coke. The material was charged to a crucible, which was suspended in the balance. CO-gas was distributed through a grid in the bottom of the crucible. Two sizes of ores were used; 2.4-4.8 mm and 6,7-9.5 mm. Coke particles were in the size range 4.8-6.7 mm. Experiments were conducted in the 900-1100°C temperature range. The composition of the product gas was monitored continuously. External mass transport between bulk gas and particle surface does not seem to limit the rate of reduction. Assuming that both diffusion through product layer and chemical reaction at the interface between MnO and Mn)04 are rate controlling, the data was tried both in a shrinking core model and in a grain model using regression. The grain model gives the best physical description of the process, because the reactant is in fact a porous medium. With this model the effective diffusivity was calculated to be in the 1.5-6.10.5 m2/s range. The pore size was mainly between 0.1 and 10 um,

Jan 1, 2003

By Z. M. Zheng

Cyclic voltammetry, potential step, and ac impedance techniques were applied to study the electrochemical reaction of arsenopyrite in chloride solutions. The relationship between anodic current density and time in potential step measurements indicates that the oxidation of arsenopyrite is irreversible. The results of the constant potential coulometry show that the stoichiometric factor of the total electron involved in the overall reaction is 14. It is proposed that the dissolution of arsenopyrite is retarded by coverage of sulfur produced in the reaction as an intermediate product. The measured results of ac impedance strongly support the proposition. The proposed reaction mechanism also explains satisfactorily the charging current density and Tafel slopes measured in potential step measurements.

Jan 1, 1995

By Saeid Pournaderi, Ahmet Geveci, Ender Keskinkilic, Yavuz A. Topkaya

"This study investigated calcination behavior of one of the Turkish laterite deposits, which was recently found in Sivrihisar region. Representative limonitic laterite samples (1.26% Ni) taken from Yunusemre Karasivritepe and Kucuksivritepe location were first subjected to drying. Removal of chemically bound water and other volatiles were then studied, in detail. In the calcination experiments, temperature and time were the main experimental variables. Thermal treatment was conducted at the specific temperatures in 250 °C - 800 °C range. The weight losses due to elimination of chemically bound water and other volatiles were reported to be approximately 10 per cent of the weight of the ore. For the particle size used in the current work, 700 °C and 40 minutes were determined to be the optimum calcination temperature and time, respectively.IntroductionThe nickel ores that are economically valuable can be grouped into two categories: sulphide type nickel ores and oxide type nickel ores, namely laterites. Over all reserves in the world, 40% are sulphide nickel ores and the remaining 60% are laterites [1]. Pyrometallurgical nickel extraction from sulphide type nickel ores is conducted via matte smelting. More recently, laterite ore bodies have been subjected to nickel extraction. Depending mainly on the chemical composition of the laterite and the process economics, various extraction techniques have been implemented: pyrometallurgical route involves ferronickel smelting. High pressure acid leaching (HPAL) is the commercial method for hydrometallurgical nickel extraction, while ammonia leaching (CARON Process) is a combination of pyrometallurgical and hydrometallurgical processes [2]. With the improvements in these processes, it is predicted that laterite’s share in the world nickel production will rise to 50% in 2012, while it was reported to be 42% in 1,200,000 tons of annual production in 2003 [3]."

Jan 1, 2011