Search Documents

By Xiping Chen, Wangxing Li, Jiemi Zhou

"Desulfurization methods suitable for anode-grade petroleum coke (coke for short) used in primary aluminum industry are coke desulfurization during calcination, desulfurization in soakage and desulfurization in mediums. Coke desulfurization during calcination is discussed in this paper. Influences of calcination temperature, holding time and coke granularity on coke desulfurization were discussed. Experimental results show that calcination temperature has a remarkable influence on coke desulfurization. When the temperature is high enough desulfurization ratio of coke can reach 85% only by calcination. Holding time has a definite influence on coke desulfurization, but desulfurization ratio is low at the temperature of 900~1300°C. The influence of holding time is obvious when calcination temperature surpasses 1400°C. The influence of coke granularity is smaller compared with calcination temperature and holding time.IntroductionPetroleum coke is main raw material for carbon anode in primary aluminum industry, and its weight percentage in carbon anode is about seven percent. Green coke can not be directly used for anode production because of its immanent moisture and volatiles. Green coke must be calcined in order to meet the request of anode production. Calcination is a heat-treatment process during which green coke is heated to a given temperature to remove volatiles, moisture and some sulfur. Real density, strength, electrical conductivity and anti-oxidation ability of petroleum coke can be improved by calcination and calcined coke can be received [1, 3, 4]. Sulfur in calcined coke finally goes into carbon anode. During baking or aluminum smelting, the sulfur in anode ultimately changes into SO2 and emits from anode into the atmosphere. Excess SO2 easily leads to acid rain which brings heavy pollution to the environment [1, 2]. With the development of Chinese aluminum industry, consumption of anode-grade petroleum coke increases year by year, the total consumption in 2007 surpassed 4.5 million tones and the yearly emission of SO2 from aluminum smelters has exceeded 270 kilotones. From 2005 Chinese government began to limit the emission of SO2 from primary aluminum industry, so desulfurization of anode-grade petroleum coke becomes more and more urgent. Some relationship need to be found and used to guide desulfurization of petroleum coke."

Jan 1, 2008

By Luis Velazquez, Andrea Zavala, Nora Munguia

"This paper is aimed at describing the evolutive strategy in which the University of Sonora is following for optimizing the organic and inorganic material life cycle in the products used on campus. The institutional strategy has be oriented towards new patterns of behaviors in order to integrate the principles of sustainability as a guideline for preventing, eliminating, and/or reducing the negative environmental and occupational impacts generated when performing university substantive functions of teaching, research, and outreaching and partnership as well as its management operation tasks.IntroductionThe University of Sonora is the largest and most important university among several other universities in both the city and the state. It is a public university with a 29,792 students in three campuses in the state. The main campus of the University of Sonora is located in the capital city of Hermosillo, which has a population of more than 609,829, in the state of Sonora in the northwestern region of Mexico [1].Despite the fact that in the University of Sonora there were, in the eighties, some projects dealing with environmental issues, there was not until 1992 that the sustainability efforts were really initiated. It happened when the Sustainable Development Group was created in the Department of Industrial and Systems Engineering as a response to the need for adapting the industrial engineering curricula to the challenge of sustainable development [2]. In order to promote sustainability, it has been necessary to cope and break with several university paradigms. For this reason, the strategy for becoming a sustainable university has continuously evolved throughout the years from a simple structure composed by individual and isolated projects to a systematic and integrative Sustainability Management System. Thanks to this evolution, the University of Sonora has won a respectable reputation in the greater community and it is seen in the region as an icon of sustainability promoter. In this sense, the substantives functions of education, research, and outreach and partnership, which are considered supportive and integrative, have also evolved to play a key role for the success of sustainability initiatives.The institution has followed four avenues for becoming a sustainable university; education, research, outreaching and partnership and greening the campus [3]."

Jan 1, 2008

By Carlos A. Ferreira, Betina Hansen, Marco A. S. Rodrigues, Marcela P. Proença

"Nowadays, the concern with the reduction of industrial pollution has motivated researchers to found out new technologies for treatment of industrial waste. The clean technologies, as electrodialysis, are capable of treating these residues, minimizing the impacts when they are discarded directly on the environment. Membranes of SPS/HIPS, PAniCSA/SPS/HIPS, SPAN/SPS/HIPS were developed using chemical mixture method. Membranes were characterized by Infrared Spectroscopy (FTIR), Thermogravimetric Analysis (TGA), Dynamic Mechanical Analysis (DMA) and Scanning Electronic Microscopy (SEM). Membranes were submitted to electrical polarization and to electrodialysis at NaCl and KCl solutions, in order to determine ionic transport through the membranes. Results were compared with commercial membranes. The average percent extraction for Na+ ions obtained by membrane was beyond 20%.IntroductionThe high environmental impact caused by the galvanoplastic industries represents today a world concern(1). In the galvanoplasty, thin metallic layers are deposited on metallic surfaces(2) through chemical methods or electrochemical process. This industrial process presents some disadvantages that limit its utilization, as the generation of toxic effluents containing concentrations of heavy metals usually above the limits allowed for his release in receiving bodies(1), the production of galvanic sludge which is considered hazardous waste and that is very difficult to treat, beyond the high consumption of water (3).Stimulated by the development of new ion-exchanged membranes with high selectivity, lower electrical resistance, and improved thermal, chemical and mechanical properties, the use of electrodialysis in the wastewater treatment has recently gained a broader interest(5). The electrodialysis (ED) is a mass separation process in which electrically charged membranes and an electrical potential difference are used to separate ionic species from an aqueous solution(5). The technique permits the recovery and the reutilization of the waste products from the industrial process, avoiding the discharge of them on the environmental (acting as clean technology)."

Jan 1, 2008

By Magdelinka Padenkova-Yaneva, Emilia Christova Kostakeva

"One of the methods for waste treatment is composting during which as a result of controlled biological decomposition of organic waste in aerobic conditions harmless materials are received. Composting takes place in suitably designed premises which ensure the optimal conditions for biochemical decomposition of the waste. A usual way to process composting is the spreading of the waste on a base made from reinforced concrete.In the paper the phases and basic technical features of the process of composting, the requirements and properties of the base and the ways of protection of concrete base against corrosion are revealed. Technical decisions for a specific construction site in Bulgaria are shown and the advantage of achieving durability of the concrete constructions in the plant while achieving simultaneous environment protection from pollution is discussed.IntroductionComposting is the process of controlled biochemical decomposition of vegetable and animal organic waste in aerobic conditions as a result of which harmless materials are obtained. The latter have better stability and are rich in humus substances which are useful for agricultural crops and can be used for restoring the soil fertility [1, 2, 3, 4].In modern waste treatment plants a composting technology is adopted in which the waste is spread on a concrete base as piles with certain dimensions [1, 3]. These piles are periodically stirred or air is blown through them in order to ensure the quantity of oxygen required for the process of aerobic decomposition of the organic matter. The fluids and gases formed in the course of the composting are take away in order not to pollute the environment – air, water, and soils. For this purpose the base on which the waste is spread must satisfy certain requirements, and the gases must be taken away and rendered harmless in order to protect the atmospheric air from pollution. This paper discusses the need for protecting the concrete base from corrosion and characterizes the stages and main parameters of the composting process and the possibilities for primary and secondary protection of the concrete base from corrosion. Specific technical decisions applied in a composting facility in the area of the town of Plovdiv are presented."

Jan 1, 2008

By C. Niedersberg, M. K. Almeida, R. M. C. Santana, V. G. Dalenogore

"The major source of environmental pollution in urban areas is the transport sector and its impact on human health and the greenhouse is preoccupying. In many works of literature is monitored the pollutants in urban cities, however in specific areas such as universities, they are scarce. Therefore, the aim of this work is to monitorate the gaseous pollutans in a bus terminal at Santa Cruz do Sul University-UNISC and to develop a control framework of the air quality. Six points were selected for monitoring, being one of them inside a bus. The monitoring of CO, HC and CO2 were carried out on arrival and departure of the bus. Preliminary results conducted in a day of spring showed that the most critical condition was during the night shift, where the concentration of CO (200 ppm) was the highest, caused by the vehicles increase, due to the larger number of students.IntroductionAccording to Mascarenhas et al, 2005, air pollutants are responsible for various effects on vegetation, ecosystems and is recognized as one of major public health problems of today, with harmful effect on humans even at levels considered safe by Brazilian legislation.There are numerous scientific papers linking air pollution with respiratory problems, cardiovascular which hinder the daily life because many of these diseases are chronic and may even lead to death, as was noted by Brook et al, 2004.There is a significant increase in the last decades of emissions to air resulting mainly from human activities. Already being observed the relationship of these emissions with the change in global climate, IPCC, 1995.They are a multitude of pollutants from the atmosphere, and its sources and its effects. The effect of Greenhouse gases (GHG), representing less than 1% of the gases in the atmosphere, controlling the flow of energy in the atmosphere. The increase in emissions of greenhouse gases is affecting the Earth's average temperature, which depends on the balance between these flows, in particular the flow of solar radiation reaching the surface and the flow of infrared radiation sent into space.One of the main greenhouse gases to this imbalance is the gas methane (CH4). Methane is produced by anaerobic decomposition of organic substances, through the action of bacteria metanogenic conditions that require highly reduced to its growth. This gas is released into the atmosphere mainly by transport diffusive by aerenchyma (vascular tissue) plant and also by diffusion through the water slide. (Bont et al., 1978)."

Jan 1, 2008

By Petr Sulovsky, Pavel Leber, Jaroslava Ledererova, Miroslav Svoboda

"The properties of raw materials used for the production of building materials play an essential role in their choice. Industrial waste materials can in some cases improve the performance of new building materials, when compared with classical raw materials. The addition of waste can however negatively impact some of the building material´s characteristics, influencing its stability, service time, durability, and can introduce undesirable variation of certain characteristics over time. It is necessary that each secondary raw material intended for such use be thoroughly investigated in terms of its chemical, physical, and mechanical properties, with special attention paid to the risk components and risk parameters. It is necessary to make many- sided technological tests in relation to the required characteristics of the resulting materials for each chosen application. Moreover, the limit values for the critical (risk) parameters, which the given secondary raw material must satisfy to be used in a specific technology, need to be defined. Introduction The risk components in the industrial waste materials to be used in the production of building materials fall into two groups: - components that pose a risk of development (instant or delayed) of a process deleterious to the utility properties and durability of the resulting materials. Such processes include volume change (expansion as well as shrinkage), alkali-silica reaction, delayed ettringite formation, thaumassite attack, aggressive carbonation, etc. - elements or components that can, if released from the waste-containing building material, pollute the environment. They involve the so called potentially hazardous elements as well as compounds like fenols, PCB, PAHs etc. From the viewpoint of the presence of both groups of risk components, the wastes can be classified as: • environmentally inert waste materials. They are produced in the largest volumes and do not pose a threat to human health. Their physical and/or chemical characteristics fail to satisfy all requirements for utilization in ordinary production. The aim of technology design is to work them into the building products with suitable utility properties. • easier workable waste materials containing toxic components are produced in large volumes. In spite of the content of toxic components, their physical and chemical properties make them suitable for ordinary production, provided that the harmful substances are immobilized by the chosen technology."

Jan 1, 2008

By P. Hanniala, J. Sulanto

"The requirement for the reduction of sulphur dioxide emissions from copper smelters is becoming more and more important. Therefore, the most important question in smelting technology will be how to produce even, high strength SO2 gas in smelter and how to combine smelting and converting. The best sorution in certain cases is to eliminate converters totally.Outokumpu is already responding to this challenge. As a result of extensive research work, Outokumpu Oy has developed the Flash Smelting Process for direct smelting of blister copper from concentrates in one step.The newest process development is the Kennecott-Outokumpu Flash Converting process, where solidified copper matte is converted into blister copper. The production of low volume high SO2 content gases, separation of smelting and converting operations to allow increased on-line availability, and simplified process control are the major benefits of the process which translates to reduced smelter capital and operating costs.Also, it has been studied the use of the same Outokumpu furnace for smelting and converting alternately when the production capacity is low.In this paper, the developments and improvements of the Outokumpu Process are described from the operation and investment cost standpoints"

Jan 1, 1988

By Ashok D. Dalvi

Production of nickel from laterite ores has occurred for over 100 years beginning with processing of garnieritic ores from New Caledonia. However, until now the world nickel supply has been predominantly from sulfide sources. Going forward, the authors project that the production of nickel from sulfide ores will remain more or less constant. Most of the expansion in nickel production capacity over the next ten years will come from processing of laterite ores. Thus the capital and operating costs of new laterite projects will have significant impact on the nickel supply and therefore price. The authors have reviewed the history and capital and operating costs of various recent laterite projects and capital and operating costs of these projects and those "on the drawing board". The authors have also evaluated the risk associated with such projects. The paper will discuss the impact of this and the recent history on the future development of laterite nickel projects.

Jan 1, 2004

By A. V. Tarasov

In order to improve technical, economic and environmental performance of hydrometallurgical processing of intermediate products containing copper and nickel, the Gintsvetmet Institute and the IMET Institute of the Russian Academy of Sciences have conducted studies into the efficiency of the use of alternating current of industrial frequency on processes applied for hydrochemical leaching of various copper- and nickel-containing materials. It has been found that: 1.Imposition of alternating current over the process of leaching of softly reduced nickel oxide with recycled copper sulfate solutions resulted in an increase by 20 to 30% of the rate of the copper cementation process and reduced by 20% its activation energy. At the same time, the recoveries of nickel, cobalt and iron to the leach solution increased up to 82.2%, 78.5% and 57.1%, respectively, and that of copper to the cement precipitate up to 74%. Optimal process conditions have been identified with respect to the current density, electrode material, copper concentration in solutions and the process temperature. 2.In the process of hydroelectrochemical sulfuric acid leaching of nickel and copper sulfides, the grain size, the phase form of sulfides, the solution composition (H2SO4, Cl?, Cu2+, Fe3+)and the current amperage had an effect on the nickel recovery to the solution, which reached 90%, while the degree of copper transfer to solution did not exceed 20%. The process of hydroelectrochemical sulfuric acid leaching of nickel and copper sulfides with an addition of Cl? made it possible to selectively recover nickel into the leach solution along with concentrating copper in the leach residue. 3.When subjecting samples of commercial-grade magnetic fractions of converter matte to sulfuric acid leaching, the imposition of electric current, the concentrations of sulfuric acid and chloride ion in the solution and the duration of the reaction process had an effect on the process. The nickel recovery was 85% and that of cobalt and iron was 95% and the recoveries reached 97.5%, 98.3% and 99.8% as a result of repeated treatment of the primary residue under similar process conditions. Up to 75% of copper, 75% of sulfur and 99.0-99.5% of palladium was concentrated in the solid reach residues. The experimental data obtained indicates that the use of AC for hydroelectrochemical sulfuric acid leaching for separation of copper- and nickel-containing intermediate products has favorable prospects.

Jan 1, 2003

By Vladimir Lobanov, Vladimir Skorohodov, Boris Radionov, Olga Makovskaya

"The synthetic sorbents and the activated carbons which are used for the metals extraction from weak process liquors are rather expensive. It is propose to use mineral and synthetic high-porous substances which sharply increased sorption properties by special processing. For achievement the desirable properties sorbents are impregnated by specially prepared solutions. Such solutions should contain the substances or its anionic forms which on the one hand are strong enough fixed in a supporter pores, with another are capable to form the insoluble compounds with extracting metals. Selectivity is provided by chemism of the reagent interactions with extracting metal. Due to the high concentration of a reacting ion in a sorbent phase the capacity and rate of sorption increases. Formed insoluble compound remains in a phase of the sorbent and necessity of its filtration disappears. For synthesis the sulfhydryl compounds which chemical properties allow to increase degree of extraction and capacity of the activated carbon were used. At hydrometallurgical processing of precious metals mineral raw materials the commercial solutions with the concentration of gold from 0,1 to 5 mg/dm3 are received. Commonly gold is precipitated from cyanic solutions by the zinc dust. The sorption methods are widely applicable. But the synthetic sorbents and the activated carbon using to these purposes are rather expensive. Expenses for sorbents even at its regeneration can reach 10-15 % from total expenses of gold extraction from ores. When sorbent regeneration, mostly for carbon, is not provided, this share increases to 30-40 %. Thereupon search of the sorbents combining availability, the sufficient capacity, demanded degree of extraction and the low price is actual. For the specified purpose it is offered to use the mineral and synthetic high-porous materials which sorption properties are sharply rose by special treatment. Among such substances are natural zeolites, silica gel, lignine et al. Similar treatment can improve the sorption properties of sorbents used in practice, particularly, the activated carbons. The simplest treatment of potential sorbents consists in its impregnation by specially prepared solutions. Such solutions should contain substances or its anionic forms - impregnating agents. These agents should be on the one hand strong enough fixed in a carrier pores, on the other hand are capable to form with extracting metals insoluble compounds. The more strong compounds are formed the high degree of metals extraction from solutions. The sorbents with similarly changed properties are named the impregnated sorbents."

Jan 1, 2008

By William James Middleton

The life-cycle assessment (LCA) approach can be an important tool for the quantification and evaluation of environmental impacts associated with metal production systems. At the conceptual phase of a new metals development project, LCA can: ? Aid project decision making by evaluating the environmental consequences of design decisions ? Support project permitting and reinforce site/process environmental impact assessment ? Allow environmental impact comparisons between alternate flow sheets For existing metals production systems, LCA has been used to aid targeted process improvements by monitoring recent historical trends in environmental performance, either through local or external (externalities) process improvements. This paper discusses the life- cycle assessment methodology, and its application as a supportive tool for environmental decision-making in process design and operation, and for site environmental impact assessment and permitting. Selected examples from a recent LCA performed on the Pressure Acid Leach Process for treating nickel Laterite ores are employed to demonstrate the usefulness of the tool.

Jan 1, 2004

By Duck Jae Lee, Kwan Ho Kim, Ji Whan Ahn

"In Korea, reutilization of constructions waste is gaining an increasing attention as generation of construction waste is projected to increase continuously. In current practices, the concrete waste is simply crushed and used as a low application such as paving, back filling, etc. In this study, a new process was developed comprising of heat pretreatment, autogenous milling, and density separation for complete reutilization of concrete waste. Firstly, the concrete waste was crushed using autogenous milling. The coarse size fractions from autogenous milling have a density of 2.5g/cm3 and a water absorption ration 3.0%, which meet the specification of the first class of KS F 2573. The fine size fractions were further separated using a hindered-settling column into two products 1) underflow, 2) overflow. The underflow sample was a high quality fine recycled aggregate which can be used for concrete making, and the overflow sample was an enriched cement material can be also used for CO2 sequestration by mineral carbonation. Introduction Kwan Ho Kim1, Ji Whan Ahn2, Duck Jae Lee1, Hee Chan Cho1 Recently, the importance of resource recycling is gaining a greater attention due to the increasing price of natural resource. Recycling is beneficial for not only the management of waste, but also the reducing of consumption of natural resources and huge energy consumption to treat of natural resource. The construction and demolition waste comprises the major industrial waste generated in Korea. It increased to 54 million tons in 2004, and is projected to increase to over 300 million tons in 2020, as many buildings reach the end of their 30 years life. Among total waste, the proportion of concrete waste was about 30% in Korea. Due to its large volume, recycling of concrete waste is the most important aspect of the waste management. In the current practices, the concrete waste is simply crushed and used as a recycled aggregate. The recycled aggregate has a low quality and most of them are down cycled for usage as paving material, back-filling material, concrete bricks, etc. It cannot be reused for replacement of natural aggregates because cement mortar is not separated perfectly from aggregates. These kinds of recycled aggregates tent to be weaker, more porous and have a higher value of water absorption. When these aggregates are used in concrete making, there are problems of higher total water demand, low compressive strength and durability [1-5]. And recycled fine aggregate is not almost recycled due to its low quality. In this study, a new processing circuit is developed to produce not only highquality recycled coarse aggregates but also fine aggregates and cement material from concrete waste."

Jan 1, 2008

By Andrew Shabalin, Vladimir Skorohodov, Svetlana Babaeva, ?lga Makovskaya

"At processing of some kinds of wastes (electronic scrap, secondary materials, spent nuclear fuel) in nitric acid solutions, and also in technology of silver refining, the significant amounts of palladium and platinum passes into a solution. The ion-exchange concentration of palladium and platinum in nitric acid solutions (5-500/dm3) are investigated. More than 30 various classes of ionites are tested. The most chemically resistance resins at the given conditions are identified. It is shown, that the maximum sorptive capacity to studied metals at high acidity the complexing, synthetic and inorganic sorbents possess. To definition of platinum metals sorption optimum conditions the kinetics is studied, isotherms of a sorption at various parameters from nitrate solutions are obtained. The conditions of the platinum and a palladium desorption from the pregnant sorbents and its regeneration with the subsequent reuse of materials were defined. The raw materials containing precious metals have very diverse composition and physical properties. Commonly the materials are processed by hydrometallurgical way. If gold or PGMs there are in raw materials to its opening hydrochloric acid solutions are applied. As an oxidizer nitric acid, hydrogen peroxide, gaseous chlorine, etc are used. Nevertheless, at processing of argentiferous materials and preliminary treatment of a waste including the spent nuclear fuel, nitric acid solutions are often used and the specified metals in some extent pass into solution [1]. Therefore selective extraction of PGMs from nitrate solutions is an actual problem. In the present work the ion-exchange concentrations of palladium and platinum in nitric acid solutions (5-500 g/dm3) are investigated. At the testing more than 30 various classes of ionites the most chemically resistance resins at the given conditions are identified. These resins are synthesized on the base of polyacrylate, styrene-divinylbenzene and vinylpyridine. For a selection of the most effective resin among what are made in Russia and overseas, a number of ionites with various functional groups were studied. Influence of functional groups type on a PGM sorption is shown for extraction of a palladium as an example (table 1). The presented data shows, that palladium concentration in a phase of ionites depends on sorbent type. If the increasing of solution acidity essentially reduces palladium sorption by sulfonic cation-exchange resins (KU-2×8) than its sorption by strongly basic anionites is approximately equal. Intermediate position is occupied by complexing sorbents. The latter (AN-31, SN-3, ANKB-35, Lewatit TP 207, Purolite S 930) are the most effective for extraction of PGMs from nitrate solutions from the point of view of capacity value. According to [2], solution behavior of Pt (II) and Pd (II) are similar. As is known from coordination chemistry, ligand environment of the metal ions substantially impacts to character of electronic spectra. The figure 1 shows the results of measurements of optical density of platinum bearing solutions with various concentration of nitric acid at ?=400 nanometers"

Jan 1, 2008

By A. F. Usov

"The use of the Electric Pulse Discharge method of materials destruction (EP) for disintegration of materials in an industrial-waste processing are examined. The principles and Experience of the development device of EP-disintegration have been described, the technological efficiency of disintegration of industrial minerals estimated.IntroductionThe Russian scientists have proposed and comprehensively studied the electric pulse (EP) technique which is applied in ores and materials disintegration [1, 2 ]. The different aspects of the problem have been presented by the authors in papers at many international congresses [3-6]. Recently the technique is intensively developed in many countries, and various disintegration installations are exhibited.Crashing and disintegration of ores by EP-method is characterized by high selectiveness of destruction. It provides better disclosure of mineral grains and prevent it from destruction. EPmethod reduces slurry formation. All this provides better mineral extraction at ore beneficiation and improves concentrate quality. It also prevents the product from polluting with equipment metal, inwall and grinding equipment material. The possibility to change the character of dynamic loading allows controlling grain-size composition and getting small-size product in contrast to mechanical method of crashing.The product of EP-crashing is characterized by less toughness and greater specific surface area of grains since the new surface is formed at splitting and chinks extension. The product is of high sorption and reactivity in chemical changes. Open grains of mineral spots correspond to their natural condition and it is of great importance for studying mineral.The principles of the development deviceLong-term studies of the technique carried out by research institutes such as Research Institute of High Voltages (Tomsk), Kola Science Centre of RAS (Apatity), Institute ""Mekhanobr"" (S.Pertersburg), made it possible to substantiate principles of the disintegration installations design, make exploratory stands and technological installations to carry out pilot tests and operations under production conditions. The construction design of disintegrating installations depends on many technological and physical factors. Of all the technological factors, the most significant one is to preserve the liberated product because it is the peculiarity of the EPdisintegration to have high selectivity of disintegration. The preservation of the mono-mineral product liberated from the rock mass means that this product is not overgrinding, which causes the loss of the product with slime in processing, and that the initial natural form of the mineral inclusion is also preserved because it is the size and the integrity of crystals that determines its cost value (precious minerals). On the one hand, it is provided by a stage disintegration technique, with the product classified after each stage, and, on the other hand, by selection of specific conditions of electric breakdown, which ensure high performance of electric breakdown and effective disintegration of material fragments, with the useful mineral inclusions preserved intact, with its size considerably exceeding the discharge gap. These conditions are provided by the appropriate geometry of electrodes, the discharge gap and the screen size due to the material’s nature and grain size."

Jan 1, 2008

By Nozomu Uchida, Uematsu Keizo, Daisuke Shouji

"Grain orientated microstructure was developed for the improvement of ceramic characteristics. Novel polarized light microscopy was developed to examine the grain orientation quantitatively. The degree of grain orientation was estimated from the retardation determined with a Berek compensator. The method was essential to determine a minor grain orientation, which could not be analyzed by means of conventional X-ray measurements. The data were favorably related to ceramics characteristics. The comparis of the ceramics with various degree of orientation was very important to explain the change of ceramic characteristics with processing.IntroductionMicrostructure with grain orientation has a high potential for greatly improving characteristics of ceramic. However, there has been strong restriction on processing and material for developing this structure. It has been crucial to apply forming methods involving high shear such as injection molding1). Grains must have an elongated shape.In recent years, much attention has been paid on the effect of high magnetic field on diamagnetic materials2)3)4), Many ceramic materials are known to be diamagnetic. High magnetic field has a high potential to orient grains. The principal driving force for grain orientation is the magnetic anisotropy of material, which is generated by non-cubic crystal symmetr5). This method of grain orientation is not restricted by grain shape, and can be applied to all materials having non-cubic crystal structure.This study uses alumina as raw materials, and produces alumina ceramics with orientated grain in high magnetic field (10T). Alumina has a magnetic anisotropy due to hexagonal crystal structure. The degree of grain orientation in the green and sintered bodies will be examined and their relevance to magnetic field will be discussed."

Jan 1, 2000

By James D. Navratil

Ferrites have been used to separate a wide range of substances such as dissolved metal species, particulate matter, and organic and biological materials; they have been used almost exclusively for metal waste treatment applications. The versatility of the ferrite waste treatment technique is evident in the wide variety of application methods. Furthermore, ferrites can be used to remove selected impurities in feed solutions containing metal products requiring purification. A brief overview of ferrite properties and recent applications for metal recovery and waste processing will be presented.

Jan 1, 1990

By J. C. Agarwal

Most metals are produced from minerals containing one or more of the desired metals, some contaminating metals, silicate, oxides, carbonates, and sulfides. Therefore, in the production of metals, there is generally a gaseous effluent in pyrometallurgical processes and a liquid effluent in hydrometallurgical processes. There are also solid residues such as waste ore, tailings, dust, and slag, created by the metal recovery processes. There are two important distinctions between the effluents and the residues: I. Effluents ? gases and liquids ? affect the neighboring environment for miles from the point of emission, while residues affect only the soil on which they are stored or dumped. 2. The environmental and economic effects of effluents are known and felt essentially immediately. By contrast, the environmental effects of the residues may not be known for a long time. For these reasons, the economic impact and the potential corrective actions required are very different for effluents and residues.

Jan 1, 1992

By Francis Vanbellen

In Union Minière's Hoboken smelter and refinery for complex non-ferrous materials, the treatment of recycling products, containing precious metals, occupies a dominant place. For all feed materials, the first step, prior to their treatment, is to classify them in order toselect an accurate and economical procedure for sampling as well as to dispatch them to the optimal process scheme. More than 150 different procedures for sampling are commonly used. The most important ones are briefly discussed in the paper. Precious metals bearing recycling materials vary widely with respect to their physical aspect, their chemical composition and the value of their precious metal content. All these parameters are taken into consideration to select the most appropriate process among the multiple possibilities of Union Minière's flexible integrated flow-sheet. Different stages of the operations as well as the main flow-sheets are described.

Jan 1, 1995

By Ronald K. Riddle

The processing of lateritic ores in rotary drying and preheating/pre-reduction systems has historically been plagued by problems associated with significant dust generation. These problems include handling issues, kiln capacity limitations, negative impacts on furnace stability, a reduction in nickel recovery and higher operating costs. The dust is formed in the rotary devices during heating and tumbling due to the following three mechanisms: (I) mechanical dccrepitation of the ore as a result of tumbling and attrition, (2) thermal decrepitation during rapid vaporization of internal free and bound water, and the (3) loss of free moisture which functions as a binder. This paper investigates the causes of dust formation, provides methods to reduce dust carryover from the rotary devices, and finally offers methods to recover the dust in the existing pyrometallurgical process. Keywords: Laterite, Drying, Rotary, Dust

Jan 1, 2004

By Hani Henein, J. Barry Wiskel

"The easy accessibility and power of the PC, as well as the education of our engineering students in the use of these tools, are compelling reasons for developing computer aided instructional (CAI) tools. There are a wide range of areas in the engineering curriculum where students must learn the steps and the process of applying judgement in problem solving. In the typical course instruction, · an instructor introduces theory to students; the application of the theory to solving problems is often demonstrated in the abstract. Students therefore spend a significant amount of time learning how to apply the theory to problem solving. Additional time and effort must then be spent to get students to the point of learning concepts and integrating this knowledge. A number of computer aided packages have therefore been developed for use in several courses in the materials science and engineering curriculum that encompass both calculational and instructional capabilities. This paper presents an overview of some of these packages which include the solution of a non-linear equation, the instruction of binary diffusion couples, an introduction of crystallography, an introduction to heat transfer and the solution of thermodynamic stability diagrams. The context in which these CAI Tutorials were developed and are being used will be discussed. The pitfalls in the development of these packages will also be discussed. The use of the tutorials has important implications on the expectations from an engineering education of both instructor and student.IntroductionTraditionally, it is quite routine to teach engineering students how to use a computer (the PC today for undergraduates) as a tool in performing engineering calculations or in simulating a process or a unit operation. This often takes the form of one course in computer programming, whether it is Fortran, Visual basic or a spreadsheet, and another course in numerical computation. However, the materials and electronic revolution have brought about considerable advances in computer power and speed, and accessibility. Today, the manipulation of digital images, movies, and speech are commonplace on a desktop PC.' Many mathematical models that were executed only on workstations can now be readily handled on a PC. Concurrently, more of our students own a PC even if their curriculum does not require them to purchase one. Today, virtually every university student has been introduced to the PC in either their elementary or high school education. Hence, the increased capabilities and accessibility of the PC and the familiarity of students with this tool make it compelling to explore its use as an educational tool for our engineering students. This is not a traditional role of a computer in our engineering curriculum."

Jan 1, 2000