Search Documents

By D. J. Chaiko

Aqueous biphasic extraction (ABE) processes offer the potential for low-cost, highly selective separations. This countercurrent extraction technique involves selective partitioning of either dissolved solutes or ultrafine particulates between two immiscible aqueous phases. The extraction systems that we have studied are generated by combining an aqueous salt solution with an aqueous polymer solution. We have examined a wide range of applications for ABE, including the treatment of solid and liquid nuclear wastes, decontamination of soils, and processing of mineral ores. We have also conducted fundamental studies of solution microstructure using small angle neutron scattering (SANS): In this chapter we review the physicochemical fundamentals of aqueous biphase formation and discuss the development and scaleup of ABE processes for environmental remediation.

Jan 1, 1996

By Hiroyuki Matsuura

The effects of P20S or Na20 addition on the reaction rate of CO2 dissociation on the surface of FexO-base molten oxides was investigated at 1773K by isotope exchange methodl-6_ The rate constant decreased with increasing P20S content of molten oxides and the residual rate constant was observed at high P20S content On the other hand, the rate constant increased with increasing Na2O content for FexO-SiO2 melts. The rate constant was evaluated by the composition of oxides and the rate controlling step of CO2 dissociation was discussed.

Jan 1, 2003

By A. R. G. Azevedo, G. C. Xavier

"The search for technological innovations in the Civil Construction takes as an objective the reduction of costs and increase of the productivity. However, these technologies demand analysis and studies of parameters of control that provide the quality of the products. With the intention of improve the knowledge on industrialized mortars used in mechanized projection machines, a characterization was done in the state anidro, fresh and hardening of three mortars, being each one of a State, Rio de Janeiro, Sao Paulo and Bahia. The tenors of water/ mortar was obtained through tests done in built environment, it varied from 0,17 to 0,26. From these results, the mortars were projected by his respective consistency, analyzing its compressive strength, and traction adherence resistance, in this way, the good performance of the revetments was provided.IntroductionThe market competitiveness of Construction has led companies to invest in construction processes and techniques in order to rationalize and optimize the buildings. Thus, changes emerged in coating system providing improvements in conventional materials and novel construction techniques, such as mortar industrialized and mechanized projection.Adopting projection equipment mortar is flagged as one of the solutions to reduce the interference of hand labor in construction, optimizing the performance of internal and external coatings, as well as streamline the production process and transportation, reducing lossesMaterials and deadline for execution of the casing(l)The process has been used due to its benefits, however, studies are necessary parameters for quality control of these mortars used in the projection to greater knowledge of mixing and market acceptance. It is therefore quite relevant information processing techniques available on the subject, as necessary to carry out research aiming at defining specific indicators of quality."

Jan 1, 2013

By F. F. Aplan

Though over 100 minerals are known to contain the rare earth (RE) or lanthanide elements, only a few provide the bulk of the world's source of these elements. The principal RE-containing mineral, monazite [(Ce,La,Th,Y)PO4], is recovered by gravity, magnetic, electrostatic and flotation concentration methods, while the other important source mineral, bastnasite [CeFC03], is concentrated by flotation. The processing of the lesser important source minerals is discussed, as is the recovery of the lanthanides from apatite [Ca5(P04)3(F,OH)] where the rare earth elements are present from trace amounts to over 10% as the mixed oxides.

Jan 1, 1989

By Hong-ying Xia, Bao-bao Wang, Jin-hui Peng, Bing-guo Liu, Li-bo Zhang, Zhi-qiang Li

Based on optimization using response surface methodology designed by Box- Behnken, to study the interaction of wet industrial salt with moisture drying temperature (50-90 ); duration (10-50s); and the weight of the materials (20-60g). The results show that: the experimental parameter conforms to the quadratic equation model to influence the moisture content and the dehydration speed., in analyzing the significance and the interaction of various factors, the optimum by the Design Expert software conditions for drying with microwave radiation include temperature of 90 , duration of 10s, and sample mass of 26g. Verified by experiment, the moisture content after drying is less than 0.25% and the dehydration rate reached 1.37g/min, between the predicted value and the actual value confirmed good fitting degree.

Jan 1, 2015

By Asmo Vartiainen

Background of Direct-to-Blister Flash Smelting is discussed; especially slag chemistry relating to copper solubility, slag fluidity and impurity behavior. In December, 2000, Mini-pilot Flash Smelting test runs were carried out at Outokumpu Research Oy to produce blister copper from Chilean concentrate and white metal and from a mixture of them. Tested slag types were iron silicate slag, ferrous calcium silicate slag and calcium ferrite slag with different slag compositions and different concentrate/white metal ratios. The test runs were successful. The fluxing effect of copper oxide was clearly demonstrated and ferrous calcium silicate slags remained fluid on a very wide liquidus range. The distribution of arsenic between ferrous calcium silicate slag and blister copper is much higher than between iron silicate slag and blister copper. This successful test run with the new slag type offer new possibilities in Direct- to-Blister process design.

Jan 1, 2003

By I. Gaballah

The kinetics of oxychlorination of pure CI-2O3 with C12+02 gas mixtures is studied by ThermoGravimetric Analysis (TGA) in non and isothermal conditions up to 1000 °C. The reaction of Cr2O3 with C12+O2 chlorination gas mixtures starts at about 550 °C and the reaction product is CrO2Cl2. The oxychlorination rate of Cr2O3 is almost proportional to the chlorine partial pressure and to the fourth root of the oxygen partial pressure in the chlorinating gas mixtures. At 800 °C, the maximum chlorination rate is obtained using a gas mixture having a C12/O2 ratio equal to 4. The apparent activation energy of the oxychlorination reaction of Cr2O3 is 87 and 46 kJ/mol at temperatures lower and higher than 650 °C, respectively. By varying the chlorine and the oxygen partial pressures of the oxychlorinating gas mixtures at temperatures higher than 550 °C, it is possible to extract selectively the chromium chlorinated compounds from the chromium bearing materials. a. Laboratoire Environnemem et Minéralurgie, BP 40, 54501 Vandceuvre, France, b. École Nationale Supérieure de Géologie, Rue du Doyen Marcel Rouhault, 54501 Vandoeuvre Cedex, France, c. Centre National de la Recherche Scientifique, 3 rue Michel - Ange, 75794 Paris Cedex, France, d. Insritut National Polytechnigne do Lorraine, Rue de la Font de Haye. 54501 Vandceuvre Cedex, France.

Jan 1, 1997

By J. A. Sekhar

Solidification processing/casting is increasingly being adopted as the preferred manufacturing technique for the fabrication of net shaped complex geometry components. Modeling of solidification processes is important both for design purposes as well as for understanding the physics of morphological evolution of the solidification microstructure. A fundamental aspect of such modeling involves the precise understanding? of heat transfer through the two phase solid/liquid region. A scheme to do this will be presented where the nonlinearity of the fraction liquid with change in temperature can be incorporated into the numerical calculations. The importance of properly accounting for the non-linear mushy zone will be discussed. Typical processes like squeeze casting and electromagnetic stirring will be discussed to illustrate how precise modeling of the solid/liquid region can aid in the calculation of accurate heat transfer coefficients for these processes.

Jan 1, 1990

By Dolf Gielen

This paper discusses the results of a Western European energy and materials systems engineering study that analyses the impact of greenhouse gas (GHG) emission reduction on the future of the steel and aluminum industry. he technology selection will be significantly affected by future CO2 policies. The avail- ability of C02 removal and storage technology and the social acceptance of this strategy for GHG emission reduction is of key importance for the strategy selection. The use of coal based smelting reduction technologies is optimal in case of weak C02 policies or in case of strong C02 policies and low CO2 removal and storage costs. The selection of CCF or Corex technology depends on the penalty regime. However, if C02 removal proves to be problematic, CCF development fails and strong C02 policies are introduced, the gas based DRI production processes will become more attractive. In both cases, the energy efficiency of the iron and steel industry will further increase in the next decades. The impact of GHG emission reduction on aluminum prices and aluminum use can be significant. However contrary to common notions the aluminum production will be positively affected by GHG emission reduction, notwithstanding the currently high emissions in aluminum production. A combination of emission mitigation in production and significant GHG emission reduction effects further down the product chain cause this effect. A significant potential exists for improved materials efficiency. This potential is generally neglected in energy efficiency and CO2 reduction studies. However improved steel qualities are of similar importance for C02 emission reduction as increased energy efficiency. It remains to see if this potential will be used to its full extent in the next decades. Model calculations indicate that the impact of C02 policies on the competition with other materials will be limited. Greenhouse gas emission mitigation will have much more impact on materials production and waste handling than on materials consumption.

Jan 1, 1999

By J. Y. Hwang

The relationship between coal characterization and physical cleaning has not been well understood due to the complex nature of coal. Therefore, it is difficult to apply the results of coal characterization to predict and evaluate the performance of a physical separation (e.g. flotation). Eight U.S. bituminous coals were analyzed and studied petrographically in conjunction with washability and flotation tests. The results show that grindability correlates to ash and fixed carbon contents; liberation determined directly by petrographic techniques is close to liberation determined indirectly by washability; and an ideal separation efficiency can be determined by measuring the inertinite content and the washability separation efficiency using a heavy liquid with a density of 1.4. The ideal separation efficiency was attained for most coals by packed column flotation. The ideal separation efficiency can be used for comparing process technologies and process parameters.

Jan 1, 1988

By G. G. Krishna Murthy

Several experiments were conducted to determine the rates of heat transfer coefficients of CaO-SiO2-A1203-FeO slags at temperatures in the range 1623-1823 K The experimental technique involved measuring heating rates of a solid specimen, sub¬merged in slag phase, using a temperature probe made of Pt\ 10%Rh-Pt. Effect of %FeO (3-10%), %FeS (0.1-0.68%), %P205 (0.2-3.0%), %MgO(5-6%), and %MnO (0.96-3.84%) present in the slag on overall heat transfer coefficient, U, of slags was investigated. Simple first order heat balance equation in combination with experimental plots rising temperature of solid specimen versus time were employed to determine the values of U. The values of U determined in the present investigation were present in the range of 70-260 cal/Ks.m2. The value of U increased with increasing the slag temperature. The values of U were not effected by increased amounts of sulfur in the slag phase. The increased concentrations of MgO, FeO, MnO, and P205 in the slag phase decreased the values of U. On the other hand, the increased amounts of Fe2O3 in the slag phase increased the value of U. Comparison of the results, obtained using the slag bath stirred by argon injection, with those determined without any stirring indicated that both radiative and conductive heat transfer mechanisms are important even at high temperatures.

Jan 1, 1993

By Daniel K. Lindberg, Fiseha Tesfaye

To reduce the use of fossil fuels and increase self-sufficiency in energy, nowadays, there is an increasing interest to produce heat, power and transportation fuels from renewable resources. Solid biomass is one of the most important renewable energy sources for meeting this target. However, fouling, slagging, and corrosion threaten long-term operation availability and costs of biomass power plants. Slags accumulated on the surfaces of superheaters, which decrease thermal efficiency, often constitute a considerable percentage of complex inorganic phases. However, thermodynamic properties of the complex inorganic phases and their combined effect, which will help to deal with the slag related problems during high-temperature biomass combustion processes, are not well known. In the present paper, thermodynamic properties of K-, Ca-, and Na-based inorganic phases and their mixtures under different gas conditions are both critically reviewed and experimentally studied. The obtained results are presented and discussed.

Mar 1, 2017

By H. Yin, T. Emi

"Advantages of gas/flux injection technology as materialized in the main stay unit processes for steelmaking are depicted covering hot metal pretreatment through secondary refining. Current status of micro-kinetic issues involved in the injection technology are reviewed including gas-in- metal, gas-in-slag, flux-in-metal, metal-in-flux and three-phase dispersion systems with reference to macro-kinetics. Key problems are briefly addressed to further develop injection technology for steelmaking processes.1. FROM PAST TO PRESENTApplication of gas injection to steel industry started in early 1950's when inert gas bubbling via stopper rod, lance, or porous refractory plug was practiced to make the temperature of steel melt in ladle uniform The gas bubbling in ladle was then extended to slightly removing hydrogen ti'om the steel melt tapped from Electric Arc Furnace (EAF) and Basic Open Hearth Furnace (BOH) when vacuum processing facilities were not popular. Later, oxygen gas injection via calorized steel pipe into molten steel bath in BOH Furnace was also put into operation to promote the decarburization to increase the productivity of the process. This line of development has been made in parallel with more profound processes, i.e, top blowing Basic Oxygen Furnace (BOF) for primary steelmaking and side blowing Argon Oxygen Oecarburization (AOD) vessel for decarburizing stainless steels.On the other hand, injection of fluxes into steel bath was first industrialized in Germany in 1960's, Primary objective was to desulfurize steel melt in ladle by injecting CaC2 or CaCrCaO mixture via lance under neutral slag cover with good success. Difficulties in injecting fluxes without clogging and rippling at a desired flux/gas ratio, and durability of injection lance were resolved in due time to bring forth many injection facilities to flourish for versatile refining operation. Top injection of fluxes from main oxygen lance to BOF was also industrialized as LDAC to promote early slag formation. A new process then emerged which injects oxygen gas and fluxes together through concentric annular tuyere, installed at the bottom of the BOE into steel melt. This process, developed in Germany [Oxygen Bottom Maxhutte (OBM)] and brought into maturity in USA (Q-BOP) and Japan in a large scale operation, became the predecessor of the combined blowing (top and bottom blown) BOF which dominates modern steelmaking."

Jan 1, 1996

By Pengfu Tan

A thermo-chemical model of the copper P-S converter and a viscosity model for the converter slag have been developed to predict the behavior of magnetite in the converter slag, amounts of slag and matte, compositions of slag and matte, volume of the bath, bath temperature, slag blow endpoint determination, SEMTECH OPC signals, and the viscosity of converter slags. The predictions of bath temperature, slag and matte compositions, and magnetite content in the slag have been validated by the industrial data. The effects of fluxing strategy, returns and skim charges, oxygen enrichment, and temperature on the magnetite formation in the slag have been predicted and discussed. The effect of oxygen potential, SiO2/Fe in slag, detection of slag blow endpoint, and temperature on Fe3O4 content in converter slag, slag viscosity, liquidus temperature of converter slag and skimming operation has been modeled and discussed as well. Some applications of the industrial operations have been presented.

Jan 1, 2009

By V. B. Telles, J. A. S. Tenorio, J. O. Alves, D. C. R. Espinosa

"The world production of crude steel in 2009 reached 1.2 billion tons. For each ton of steel produced, 150 kg of steelmaking slag and 20 kg of steelmaking dust are generated. These are wastes with considerable production and limited applications, therefore this work studied the recovery of these wastes into useful sub-products. The slag was used as raw material in the production of rock wool (a thermo-acoustic insulator) and the dust was inserted in the iron ore sintering process. Results showed that produced materials have exceptional proprieties, therefore the recovery of these wastes can contribute to decrease extraction of non-renewable resources, reduce the costs and impact of disposals, and aggregate value to the slag and dust.1. IntroductionSteel production using Eletric Arc Furnace (EAF) has grown over 119 million tones in the last years. In 2008 30.7% of all steel produced, was obtained through EAF. In United States of America (USA) the percentage of this process in the production of steel was about 58% in 2008, while in 2000 this percentage was only 47% [1]."

Jan 1, 2011

By A. S. Usrnani

Due to both turbulence and the highly variable geometry of castings, a realistic numerical simulation of the metal flow is prohibitvely expensive with current technology. However, when the chief purpose is to achieve realistic thermal fields a precise How simulation is not necessarily required. In this paper we assume a laminar flow regime and obtain the flow field by solving the incompressible Navier-Stokes Equations using a velocity-pressure segregated semi-implicit finite element method. The free metal surface is predicted by advecting a pseudo-concentration function via the computed How field. This involves an explicit finite element solution of a pure advection equation. The thermal field is calculated by solving the convective-diffusive energy equation by an explicit finite element method using the computed flow field and the location of the free surface. All the advection terms are discretized using a Taylor-Galerkin method. The interface between the metal and mould is modelled using special interface elements. The model is demonstrated by solving practical example problems. The results show that a sharp thermal front is maintained during the course of filling without excessive diffusion. The heat diffusion in the mould can be controlled by varying the metal mould heat transfer coefficient.

Jan 1, 1994

By R. E. Johnson

The No. 3 reverberatory furnace at Phelps Dodge. Corporation's Morenci, Arizona copper smelter first received oxygen from a new oxygen plant during October 1982 and began operation with oxygen-fuel and oxygen sprinkle smelting burners which burn concentrate with oxygen. The furnace was completely converted to roof-mounted oxygen-fuel firing in October 1982. All conventional air-fuel bridge wall burners were extinguished at that time. The novel arch-mounted oxygen sprinkle smelting system began continuous operation April 1983. Since startup, unit fuel requirements decreased and furnace throughput significantly increased. Furnace off gas SO2 strength increased from an average of 1.5% SO2 to an average of 20% using only oxy-fuel burners. Oxygen sprinkle burner operation also has given excellent results, with the furnace off gas strength increasing to 35%-60% S02. There has been a reduction in overall arch temperatures, an increase in matte and slag temperatures, and a lowering of furnace bottom buildup with oxygen smelting. Furnace off gas is blended with converter off gas and treated in a sulfuric acid plant.

Jan 1, 1983

By Jongmin Jeong, Jaehong Shin, Joo Hyun Park, Chul-Woo Nam, Kyung-Ho Park

Because sulfur and phosphorus are very harmful in steel products, there are increasing requirements for refining these elements from ferroalloys industries. Hence, in the present study, simultaneous desulfurization (de-S) and reducing dephosphorization (Rde-P) from silicomanganese (SiMn) alloy were investigated using metal-slag equilibration method under highly reducing condition at 1773 K. Experiments were carried out by equilibration between SiMn alloy and MnO-based slag in graphite crucible under p(O2) = 10−18 atm. Slag composition was designed by changing basicity (CaO/SiO2) and MnO content at fixed Al2O3 (=20%) and MgO (=5%) contents. De-S ratio increased with increasing basicity until C/S = 1.5 whereas Rde-P ratio was not significantly affected by slag basicity. This was because thermodynamic driving force of de-S reaction was greater than that of Rde-P reaction under present experimental conditions. The de-S and Rde-P ratios commonly increased with decreasing oxygen partial pressure.

Mar 1, 2017

By Yongzhong Xiao, Tiejun Chun, Jian Pan, Zhen He, Deqing Zhu

"In this paper, the reduction kinetics of low grade hematite ore was calculated. Mineralogy shows that the ROM (run of mine) ore is of low grade hematite ore type, assaying 27.2 wt% Fetotal and with main valuable minerals of hematite. The reduction kinetics shows that the reduction reaction rates of pellets with additive and without additive are all controlled by diffusion through the product layer. The calculated apparent activation energy of pellets with 12 wt% complex additive is 8.55 KJ/mol, dropping 62.23% compared to that of pellets without additive.IntroductionWith the rapid development of iron and steel industry in China, there has been a soaring demand for iron ores in the past decade. The imports of iron ores have increased from 148 million ton in 2003 to 620 million ton in 2010[1]. Therefore, large quantities of low grade iron resources are necessary to utilize in China at the moment. During the past years, extensive research has been carried out on the low grade hematite ores [2-6], such as reverse floatation, gravity separation, high-gradient magnetic separation and direct reduction-magnetic separation. Direct reduction-magnetic separation is an innovation way to treat the low grade hematite [7]. However, the research of reduction kinetics of low grade hematite is few. Some research about the reduction kinetics of reducing iron oxides by CO was studied [8]. The results indicated that the apparent activation energy is 8.0-28 KJ/mol when the reducing reaction is controlled by internal diffusion. The apparent activation energy is 50-75 KJ/mol when the reducing reaction is controlled by chemical reaction. In this paper, the reduction kinetics of pellets was also been studied."

Jan 1, 2012

By Jan Vrestal, Josef Tomiska, Pavel Broz

"Thermodynamic investigations on fcc solid ternary Fe-Ni-Cr alloys have been performed by means of the computer-aided Knudsen cell mass spectrometry. Ternary T.AP.-series (Thermodynamically adapted power series) are used for the algebraic representation of the thermodynamic excess properties. At 1650 K the molar excess Gibbs energy GE is negative over the whole field of stable fcc phase. The molar heat of mixing HE is exothermic in the predominant part of the fcc phase field. Only between the section with a constant ratio of mole fraction Xcr/XNi = 0.64 and the fcc phase field boundary the HE values are slightly endothermic. The results of this work can be used successfully for phase diagram calculations.IntroductionThermodynamic investigations on multicomponent alloy systems such as the Fe-Ni-Cr ternary system including the three binary boundary systems are very time-wasting and usually beset with considerable experimental difficulties. Additionally, the required experimental equipment is very expansive and the obtained results are not always satistying. Therefore it is understandable that many phase diagram calculations are based only on few experimental values of the molar excess free Gibbs energy GE. Consequently, Kundrat and Elliott [1] as well as Hillert and Qiu [2] used in their reassessments of the phase diagram of the Fe-Ni-Cr system thermodynamic data mainly assumed and/or optimized by means of various reasoning.Lee [3] reported recently, a revision of the used thermodynamic description of the Fe-Ni liquid phase is necessary to obtain a better agreement with the experimental data on the bcc/liquid or fcc/liquid tie lines and liquidus temperatures in the Fe-rich region of the Fe-Ni-Cr ternary system than in the previous assessments. This is 'in full agreement with mass spectrometric investigations of Fe-Ni alloys in the liquid and in the fcc solid phase, published earlier [4,5]. Indeed, phase diagram calculations based upon the molar excess free Gibbs energies GE obtained in these studies yield liquidus and solidus lines in excellent agreement with experimental phase diagram data [5]. Nevertheless, these experimental data have not been considered later on any more, not even in the revision by Lee [3]."

Jan 1, 1996