Search Documents

By Shunichi Ajima

PT. Smelting Co. was established in February, 1996 to construct and operate the Gresik Smelter and Refinery. The construction work of first Copper Smelter and Refinery in Indonesia was completed in the end of August, 1998 and it was put into the integrated test operation in December, 1998. Gresik Smelter and Refinery is designed to produce 200,000 tpy of copper cathode from copper concentrate supplied from Grasberg Mine of PT. Freeport Indonesia Company in Irian Jaya, Indonesia. As by product 592,000 tpy of sulfuric acid, 382,000 tpy of slag, 31,000 tpy of gypsum and 480 tpy of slime will be produced in the full operation. Major processes applied at Gresik Smelter and Refinery are: Smelter: Mitsubishi Continuous Copper Smelting and Converting Process ( Mitsubishi Process ) Anode Casting: Continuous Casting of Copper Anodes with the Hazelett Twin Belt Caster Refinery: ISA Process Acid Plant: Lurgi Mitsubishi Double Contact Process

Jan 1, 1999

By Li Fangi

This paper describes the characteristics and regularities of a process to recover rare earth minerals from Baotou Ore with H-205 collector. H-205 is a kind of hydroxamic acid with amide as a polar group and poly-cycle aromatic hydrocarbon as a non-polar group, having strong ability to capture RE minerals (bastnasite, monazite). When adding a certain dosage of water glass and some other modifying agents, and maintaining pH value between 8.5 and 9.5, RE minerals can be effectively separated from calcium and barium minerals, such as fluorite and barite, etc. Under normal flotation temperature and concentration, when using H-205 to float RE minerals, it needs a bit longer conditioning time (a few minutes longer than that for the conventional collectors). It is also shown that the reagent has the property of resistance to hard water. The laboratory scale and pilot scale tests of the process have been carried out on bulk froth containing RE minerals and fluorite taken from Ore Dressing Plant of Baotou Iron and Steel Company, in both cases, high grade RE concentrates were obtained and the recovery increased remarkably. Therefore, the process has a great practical value.

Jan 1, 1989

By W. L. Cornell

The processing of lead tailings for removal of the heavy metals produces concentrates upgraded in Co and Ni values. Reflected light microscopy, scanning electron microscopy, image analysis, and Vickers hardness measurements were used to identify mineral species, associations, degree of liberation, and distributions to the test products. Siegenite and bravoite were the most common species encountered, but violarite and enriched pyrite and marcasite phases were also identified. Liberation for the Co and Ni minerals contained in the tailings was 20 micrometers or less.

Jan 1, 1993

By Ashish Kumar

Comminution is an essential mineral processing operation to liberate the minerals from the ore. This however, is an energy intensive step in mineral processing industries. This work highlights the possibility of saving in grinding energy for ore comminution reducing work index of the ore by effective utilization of microwave energy. This reduced work index results in increased throughput of the grinding circuit in mineral beneficiation plant in order not to shift the product size. The fundamental principle behind this application remains the ability of microwave to heat individual phases within the ore matrix. The constituents of the ore typically having different thermal and mechanical properties develop stress of sufficient magnitude to create intergranular and transgranular fractures during heating and subsequent quenching of the ore. The experiments conducted with the ore samples of Zawar Mines and Rampura Agucha Mine of Hindustan Zinc Limited, India (A member of Vedanta Resources Plc) reflect a substantial up-shift in cumulative weight percentage passing in finer sieve fractions under quenched conditions. Further, the experiments carried out on Rampura Agucha ore reveal 20-30% reduction in work index, which result in decreased milling time or saving in grinding energy. The simulation studies estimates a 2-4% increase in plant throughput. Moreover, preliminary flotation studies indicated a significant increment in total metal recovery and concentrate grade for the desired grade and recovery values respectively. This paper is a technical note on the laboratory investigations carried out at Central Research & Development Laboratory of Hindustan Zinc Limited. Results have been encouraging to progress the work further. It is also proposed to carry out modeling work for simulation so as to predict the changes in minerals.

Jan 1, 2006

By N. S. Narayanan

Monazite, one of the major sources of rare earths, is normally opened by digestion with hot concentrated caustic soda solution. Caustic digestion dissolves phosphate and leaves a hydrated mixed metal oxides cake containing thorium, uranium and rare earths. By leaching this cake with hydrochloric acid at pH 3.0 to 3.2 bulk of the rare earths are preferentially removed and separated. The slurry left after removal of major portion of rare earths contains all the thorium and uranium present In the feed monazite. In addition this slurry also contains substantial quantities of rare earths. Solvent extraction tests were carried out to develop a process to separate rare earths, thorium and uranium present in the mixed chloride solution obtained by dissolving the above slurry in hydrochloric acid. Based on these tests a solvent extraction flow sheet was developed with di-2-ethyl hexyl phosphonic acid mono 2-ethyl hexyl ester as the extractant. The details of experimental work and results obtained are discussed and a flow sheet for processing monazite Incorporating the new process is suggested.

Jan 1, 1997

By Peng Fan

Liquid phase tends to migrate from an aggregate of solid particles immersed in a liquid phase into another aggregate composed of the same solid particles and liquid but with smaller particle sizes and/or lower volume fraction of the liquid phase. This type of liquid migration in a two phase system can be attributed to the driving force for the system to decrease its total interfacial energy. With liquid migration pressure as a convenient measure for the total interfacial energy of a solid-liquid two-phase system, liquid migration can be attributed to the existence of liquid migration pressure gradient in the two-phase system. The kinetics of liquid migration is of great practical importance for many industrial processes, one of which is the liquid phase sintering of functionally graded WC-Co composite materials. During liquid phase sintering, WC-Co composite forms a typical solid-liquid two-phase system where solid particles of WC are immersed in liquid Co. For a sample composed of two layers of WC-Co with the same Co content but different WC particle size, Co gradient will be formed during liquid phase sintering; while for a sample composed of two layers of WC-Co with the same WC particle size but different Co content, the Co gradient will be eliminated during liquid phase sintering. The formation and elimination of Co gradient are controlled by the liquid migration pressure gradient. This paper describes a numerical simulation of the kinetic process of the formation and elimination of cobalt gradient.

Jan 1, 2006

By Amanda C. Lima, Luiz Augusto H. Terrones, Sergio N. Monteiro

"Fabric from weaved yarns made of jute fibers have been considered as reinforcement for polymeric composites. In particular, these fabrics obtained from discarded sackcloth are presently being investigated as environmentally friendly composites with recycled polyethylene matrix. The objective of the present work was to compare the practical properties and economical aspects of these composites with those of conventional materials such as wooden board and gypsum panels for building application. The comparison showed that, depending on the amount of post-used jute fabric, a cost/benefit analysis favors these composites over the conventional materials.IntroductionThe increasing amount of wastes generated by human activities is becoming a worldwide problem of pollution with growing consequences to the environment. The question on how to dispose these wastes is, therefore, a major global issue. Among the possibilities of it gating the problem, the use of materials with characteristics of being renewable, biodegradable and recyclable is considered an environmentally correct solution. Examples of this type of materials are left over lignocellulosic fiber from coconut husks and sugarcane bagasse [1] that, after the primary extraction of edible pulp and juices, can be recover for industrial application. Nowadays, the main use of these fibers is to reinforce polymeric composites applied as components for building construction and automobile parts [2,3]. In addition to these applications, composites reinforced with residual lignocellulosic fibers may replace conventional furniture and panels made of wood and thus help to reduce deforestation [4].Environmental protection is not the only motivation for recycling natural fiber wastes. In developing regions activities associate with collecting and processing residual fibers provide job opportunities for low-income people. Moreover, if the lignocellulosic fiber is collected as a recyclable waste, it hes the economic advantage of a comparatively cost, which constitutes in a relevant difference as a choice for commercial utilization."

Jan 1, 2008

By E. S. Geskin

New material processing tools should be developed and reduced to the practice in order to meet the challenges facing the contemporary material production industry, One of such potentially important tools is supersonic liquid projectiles. It was shown that at the speed of 1500-1750 m/s the water projectile are able to demolish reinforced concrete plates, forge, to pierce and weld metals, to destroy with no explosion non dischargeable mines, etc. These projectiles are generated by simple, low cost launchers run. It is obvious that these projectiles can be applied to the ore mining and comminution. Thermodynamic considerations show feasibility of the use of these projectiles also for smelting, refining and forming. The presented paper discusses the results of the experimental study of supersonic liquid projectiles as well their potential metallurgical applications.

Jan 1, 2006

By Alex Moyano

At present, the Codelco Norte smelter processes in the Teniente Converter and the Flash smelting Furnace 1,420,000 t/y of its Chuquicamata concentrate with an arsenic content of up to 1.5%. In a near future Codelco-Chile is considering different processing options for a new projected concentrates from the Alejandro Hales mine (former Mansa Mina mine with an arsenic content of up to 6%). The main option is the possibility to process 3,000 t/d of mixing concentrates from the Alejandro Hales and the Chuquicamata mines, in the Teniente Converter. The main feature of this smelting unit will be high volatilization of arsenic when processing high arsenic-bearing concentrates. The CN smelter staff carried out a technical feasibility study to evaluate the processing of high arsenic-bearing concentrates directly in the Teniente Converter, thus the low arsenic-bearing concentrates can be processed in the FSF. Accordingly, laboratory scale tests were carried out at the Tohoku University facilities. The lab-scale results allowed an industrial scale test at the Codelco Norte smelter to smelt 2,300 tpd of high arsenic-bearing concentrates in the TC and evaluate the metallurgical impact in the smelting, converting and refining areas of the smelter. The main industrial-scale result confirmed the stabilization of the arsenic content at 0.5% in the 70% Cu produced white metal at the test condition.

Jan 1, 2006

By Kaixi Jiang, Bangsheng Zhang, Lei Zhang, Haibei Wang, Xiaoping Zou

"China plays an important role in the global molybdenum industry; in fact, both China's molybdenum mine and smelter production ranked first in the world. The characteristics of China's molybdenum resources are quite complex, and moly-nickel ores with carbon, coppermoly ores and wulfenite can be only found in China. This paper firstly introduces China's molybdenum resource/ reserve situation. Secondly, the status of molybdenum smelting technologies, especially roasting by rotary kilns and multiple-hearth furnaces, are discussed. The practices and the development of some new technologies, such as pressure leaching, solvent extraction, ion exchange, carbon adsorption for moly-nickel ores and low grade molybdenite concentrates, are also introduced.IntroductionMolybdenum is widely used in special steels, aviation, alloys, chemistry, electronic and medical industries because of its excellent physical and chemical characters [1,2].In nature, molybdenum exists mainly as molybdenite associated with copper ore which are the main material for smelting. About 99% of molybdenum is produced from molybdenite. In addition, wulfenite, molybdenum oxide ore and graphite shale containing Mo-Ni have also industrial value to extract molybdenum and other metals such as Ni, Re, Pb and Zn. The reserves of molybdenum in China are about 8.4 million tons metal; China is ranked as the second largest source in the world. The output in China is more than 40 kt in 2010. Ferromolybdenum is the main product and then ammonium molybdate. The consumption in China is about 20 kt and the rest is exported to overseas.The first molybdenum smelter in China was built in 1963. Today the main producers include Jinduicheng Moly Company, Luanchuan Moly Company and Jiangxi Copper Group Company. Technologies and equipment have changed greatly. Roasting and multi-hearth furnaces are widely used. Several new processes were developed such as pressure leaching, solvent extraction, ion exchange and carbon absorption [3-8]."

Jan 1, 2012

By L. Z. Villanueva

An investigation and evaluation has been performed to determine the potential utilization of electron beam irradiation technology for sulfur oxides removal from reduced-S02-strength metallurgical gases from copper smelters. These off-gases, though too weak to be converted to usable, concentrated: sulfuric acid by conventional means, are characterized by SO2 content higher than 2,000 ppm and a complex chemical composition, including high oxygen content and its generation occurring in a cyclical, fluctuating pattern. This work was based on information supplied by principal smelter companies in Chile. A laboratory facility with flow rate of 20 Nm3/h and equipped with an electron accelerator of beam energy 8.00 keV, has been used for testing. Influence on SO2 removal efficiency of operational parameters such as gas temperature, water vapor content, ammonia feed ratio and irradiation dose was established. The main conclusion of this work, from experimental laboratory tests as well as engineering studies, is that the Electron Beam Process (EBDS) is a cost-effective, simple and appropriate chemical process means for emission abatement. EBDS can, on a site-specific basis, adequately augment SO2 removal to upgrade overall abatement as required and in an optimal manner.

Jan 1, 1999

By Anurag Tripathi, J. K. Saha, S. K. Ajmani, J. B. Singh

"The quality of steel is a major concern in the metallurgical industry. The control of liquid steel temperature can enhance the level of cleanliness in steel. Ladle is one of the major vessels used to transfer liquid steel between different stations. The heat transfer phenomenon taking place in this vessel needs to be monitored for controlling the liquid steel temperature. A CFD model was developed for prediction of liquid steel temperature during complete process cycle of ladles in direct heats. The model was validated with liquid steel temperature measured at on-line purging station and tundish during teeming from one of the actual steel plant. The accuracy of model was 96 %. The results obtained show insignificant effect of slag thickness, tapping temperature and ladle life on liquid steel temperature in the ladle. However, the importance of initial refractory temperature was noticed. The CFD model developed in present work can generate the thermal history of liquid steel and refractory walls of any ladle at any stage.1. IntroductionThe control of liquid steel temperature is desired to achieve required steel quality. The low casting temperature is detrimental and may result in nozzle blockages due to premature solidification in the tundish. The phenomenon of heat losses taking place in ladles needs to be understood for prediction of liquid steel temperature. The assessment of thermal profile of liquid steel from BOF converter to caster can be done through consideration of heat losses at all points. Hlinka and Miller [1] showed that the ladle pouring temperature varies due to heat losses from molten steel into surrounding refractory layers. The phenomenon of thermal stratification was numerically simulated by Ilegbusi and Szekeley [2]. The effects of slag cover on heat loss and liquid steel flow in ladle before and during teeming to a continuous casting tundish was numerically simulated by Chakraborty and Sahai [3]. Investigators also developed some simple models to predict the steel temperature for some of the processes taking place in ladles [4-9].The present work is an effort to generate the full information about the temperature drop taking place in any ladle throughout its process cycle. This information can be used to predict liquid steel temperature and to take decisions to minimize heat losses."

Jan 1, 2012

By Ronald Klepper

In hydrometallurgy, pure gases like oxygen and hydrogen are used for oxidation and reduction. The gases are expensive and therefore should be used efficiently. Non reacted gas can be recycled into the liquid. Historically vortex gassing has been used; Le. a mixing impeller close to the liquid surface entrains gas from the headspace into the liquid through a gas vortex. Novel and more efficient methods are surface gassing with up pumping impellers and self- inducing gassing impellers. These alternative impeller systems are well established and common in the chemical industry, but have not been used until recently in hydrometallurgy. Gassing impellers act as internal compressors and increase the interfacial surface for a much higher mass transfer compared to alternate methods mentioned. In the paper results from lab and pilot tests and data from operated plants will be presented. The reactions with gases normally take place under moderate to high pressure, therefore a safe enclosure with mechanical seals and the safety "philosophy" is important. Experienced life and replacement cycles will be reported.

Jan 1, 2000

By Keizo Uematsu, Kumiko Sanda, Nozomu Uchida

"Full understanding of mechanical properties is the most important assignment in ceramics. Establishment of defects-property relationship is crucial for fulfilling the assignment. This study reports detailed characteristics of defects and their relevance to the mechanical properties for alumina ceramics made through a typical industrial processing. Novel characterization methods were applied to evaluate their defects. A very simple direct correlation was successfully found between defects and properties in ceramics. This result is a great epoch in the field of ceramics. IntroductionThe ceramic materials are used in refractoriness, corrosion resistant materials and structural materials. The low fracture toughness and scatter of strength are very important problems in ceramics. The toughness of ceramics is lower than metal and polymer materials, and the allowed defect size is small. Very small internal defects (pore, crack, huge particle) can be a fracture origin in the brittle fracture. The characteristics of defects such as size, distribution and shape change markedly by process condition, which cause the scatter of strength. This study conducts quantitative evaluation and direct observation of the sizes, shape and a number of internal defects with a light microscope, and discusses the relationship for mechanical properties and defect sizes"

Jan 1, 2000

By K. Dzieciol

The paper presents a study about three image correlation methods ?common cross-correlation, mutual information and phase-correlation ? applied to characterize microstructures reconstructed with X-ray tomography. It is shown that phase correlation is not only the fastest, but also the most sensitive method for detection of similar microstructure features, cavities in the present case. A new image correlation indicator is proposed, which takes into account both the phase shift and the amplitude of similar features in compared images. Some preprocessing aspects related to the tomographic reconstruction and filtering out of characteristic noise are also discussed.

Jan 1, 2009

By A. W. Bryson, S. P. Fox, S. A. Godorr

"This work is an extension of a previous investigation on the development of surface roughness during electrodeposition of copper. A comprehensive model based on diffusion and migration in a force field together with surface diffusion and sticking probabilities is used to generate profiles which are compared to those produced experimentally. The roughness is characterized by using the technique of fractal geometry which is shown to describe both qualitatively and 9uantitatively the development of surface morphology during electrodeposition.The work is extended to the deposition of copper in the presence of various concentrations of thiourea. The development of roughness is observed experimentally on the edge of a thin copper disc mounted between two glass plates. This enables photographs to be taken at various stages during growth. The surface outline is digitized using an image analyzer which enables the fractal dimension to be determined as growth proceeds. As expected, the presence of thiourea at low concentrations produces a fractal dimension which is closer to unity (i.e. the surface becomes smoother).IntroductionThe development of surface morphology during electrodeposition has far-reaching implications for copper plating in the electrowinning and electrorefining processes. Short circuits as the cathode surface grows unevenly require operator intervention in a dangerous environment and imply processing delays, and the inclusion of electrolyte in small gaps in the plated cathode have implications in downstream processing of the cathode. Higher current densities are obviously desirable, as they result in greater production rates, but as shown by Ettel et. al.(l), Harvey et. al.(2), Cook (3), and Harvey et. al.(4), it is not possible to operate near the projected economically optimum conditions because the electrodeposition of copper from sulphate and acid solutions is a mass transfer controlled process. It has been shown (Ettel et. al.(l), Harvey et. al.(2)) that the closer a system operates to mass transfer limiting conditions, the poorer the resulting cathode quality. One solution is to use agitation techniques to increase the limiting current density. Another is to add surface active additives to the electrolyte which has been shown by Ettel et. al.(l), Harveyet. al.(2) and Afifi et. a1.(5) to allow higher rates of production without decreasing cathode quality. The second proposed solution is of interest in this work, since there is very little knowledge of the conditions under which these additives operate effectively, and little fundamental understanding of the mechanism by which they operate. The current work seeks to contribute to this field by correlating a simulation model with experimental results to describe the development of surface morphology in the electrodeposition process."

Jan 1, 1997

By L. Salinas

Lance injection of gas and particles into a molten bath is currently practised in metallurgical processes (Mitsubishi lances for example). Several experimental and theorical studies have been conducted in the past on this topic. However, neither detailed calculations nor experimental studies of local flow patterns have been published. In the present work, a numerical simulation of the interaction of a gaseous vertical descending jet and a liquid surface was done, using the turbulence k-e model. There is a fair agreement between the calculated and the experimental values. The results of this study demonstrate that it is crucial that the gas jet velocity profile and turbulent characteristic are correctly formulated in order to correctly simulate the system.

Jan 1, 1999

By C. Frias, M. Garcia, G. Diaz

Advances in hydrometallurgy promoted by Tecnicas Reunidas are providing increasingly simple and clean means for controlling the entire lead recycling chain. Used in parallel with pyrometallurgy, these processes allow furnace temperatures to be reduced and fumes and atmospheric pollution to be minimised. Furnace slags are digested, and residues (mainly gypsum) are non-toxic and convertible into marketable products. In addition, the global economy of the process is substantially improved by reducing the operating cost, increasing the lead recovery above 99% and obtaining a 99.99% pure lead product. These new PLACID and PLINT processes may provide the cleanest and healthiest practicable means for recycling lead from batteries.

Jan 1, 2000

By Tian Li

Simple compartmental models of a laboratory batch gibbsite precipitator were used to investigate the influence of the number of compartments, the local shear rate and solids distribution on the crystal size distribution (CSD) under the conditions where aggregation is the dominant mechanism. In the current work, a power law relationship was assumed between the local agglomeration and shear rate. The simulation results showed that both the local shear rate and solids distribution have significant effect on the CSD responses, and the interchanging flows has a lesser impact with its influence strongly depending on the former two factors. Overall, the results reveal that in an aggregation controlled precipitation system, the influence of each of the factors on the CSD depends on the local hydrodynamic conditions in the precipitator, as well as their interactions.

Jan 1, 2003

By Luis G. S. Sobral, Gabrielle N. Bard

Copper sulphides Concentrates, from the flotation process of copper primary ore; contain, commonly, small amounts of precious metals, such as gold and silver. During the smelting process of those concentrate all gold and silver are practically in the blister copper, which is cast into anodes. Those copper anodes are electrorefined in an electrolytic system, where the electrolyte is an acid copper sulphate solution, where a high purity electrolytic copper is produced (>999,9/1000). The slime when submitted to an oxidative leaching process, using sodium hypochlorite and hydrogen peroxide as oxidizing agents, turn those metals into solution. This research practical work, apart from concentrating effort on the digestion of the anode slime, aims at evaluating the efficiency of the cementation process of the metals of interest for the separation of them to take place. 141

Jan 1, 2008