Search Documents

By Dirk Verhulst, V. I. Lakshmanan

Why Chloride Hydrometallurgy?The most available, cheapest and best known reagent for treating ores and other raw materials for the metallurgical industry is sulfuric acid. Hydrochloric acid is second in line. What often happens is that a process is developed on the basis of sulfuric acid, and that at some point the question arises: wouldn't hydrochloric acid do this better?Considering hydrochloric acid immediately opens a very interesting field of research. To summarize a few comments from another paper presented at this symposium [1]: chlorides are far more soluble than sulfates (with a few interesting exceptions); the hydrogen ion activity is greater in chloride than in comparable sulfate solutions; higher oxidative conditions are possible; regeneration is more straightforward; more diversity is possible and better conditions for the separation of species can be found for solvent extraction and ion exchange; sulfur in the ore can be separated as elemental S; higher metal concentrations in solution and more flexibility in the chosen oxidation state means significantly lower energy costs.Also, the volatility of many chlorides at higher temperature allows further separation without the need to go to a different system. Chlorides also form molten salts with a low melting point, providing another means of separation and purification in the same chloride medium.

Jan 1, 2011

By Z. Q. Chen, M. H. Loretto, Y. G. Li

"As-cast, As-forged, as-solution-treated, and solution treated and aged microstructures of Ti-15Mo (IMI205) with and without carbon were examined using optical microscopy, scanning electron microscopy .and transmission electron microscopy. Tensile testing was carried out at room temperature. It was found that carbon acts primarily as a titanium carbide former: Titanium carbides increase slightly the tensile strength, but decrease the ductility of IMI205. These observations are interpreted in terms of the titanium carbide morphology observed using SEM and TEM and the phase diagrams of Ti-Mo, Ti-C, and Mo-C.IntroductionIn a recent study on the development of a burn-resistant 13-Ti alloy, carbon was introduced· into the Ti-V-Cr system in order to optimise the mechanical properties. Research results[1, 2] demonstrate that carbon addition can refine the 13 grain size and improve the stability of the 13 phase in Ti-V-Cr alloys. The most attractive result is that carbon addition produced a marked improvement in the ductility of alloys when the carbon content is over 0.1 wt.% in this alloy system. Even after long exposure, the alloy with carbon addition maintains good ductility. One of the main reasons for the ductilising of the alloy is that titanium carbides can getter the oxygen from the 13 matrix.In view of the success of carbon addition in improving the properties and the stability of the Ti-V-Cr alloy, it is of interest to investigate the behaviour of carbon addition in other beta Ti-base alloys. The objective of the present work was, therefore, to assess the microstructures and mechanical properties of IMI 205, a metastable beta titanium alloy, with and without carbon addition using optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), wavelength dispersive X-ray (WDX) analysis, room temperature tensile testing."

Jan 1, 2000

By Susanne Pignolet-Brandom

Reflected light microscopy scanning electron microscope energy dispersive spectroscopic analysis and backscatter electron image and electron microprobe chemical analysis have been used to study lead sinter and lead blast furnace slag. These studies provide invaluable information on the phases present their intergrowths, and their chemical composition. Such information increases the understanding of the nature of pyrometallurgical processes and the behavior of minor elements during these metallurgical processes.

Jan 1, 1987

"The pyrometallurgical method of recycling car batteries suffers from a potential for air pollution violations, which prompts the desire for a viable hydrometallurgicaJ alternative. Several Processes have been proposed, including leach-electrowinning routes using HBF4 and/or HzSiF6 based electrolytes, along with anodes of PbO2 on inert substrates.A study has been carried out to evaluate the proposed systems, with the intention of demonstrating a six month life of an electrolyte-anode combination. The work, which focused on the use of HzSiF6, has indicated that there was no acceptable anode, and has lead to the development of a technique to produce smooth, glassy, adherent coatings on graphite, and to the development of an anode composed of a series of copper cored graphite rods.The paper will present results on leaching and electrowinning experiments, as well as the description of a flowsheet for a pilot plant that will be used to produce one tone per day of refined lead from spent battery paste."

Jan 1, 1997

By T. Iriyama, Y. Fujita, R. Omatsuzawa, T. Nishio, N. Okochi

Sm-Fe-N hard magnetic materials are good candidates for high performance bonded magnets. Rapid-quenching method should be highly favorable for the fabrication of isotropic magnet powder with high coercivity. We report here the magnetic properties of Sm-Fe-N powders produced by a few kinds of rapid-quenching processes. Sm2Fe17 powders were prepared by gas-atomization (GA), rotating-disk atomization (RDA), or melt-spinning (MS) method. The Sm2Fe17 GA powder had dendritic solidification structure, while the RDA powder had micro crystalline structure with size of 3-5 µm. Coercivities (HcI) of their nitrides were 56 (for GA) and 217 ka/m (for RDA). The H cI of nitrided Sm2Fe17 MS powder with wheel velocity (V5) of 5-20 m/s, which had also microcrystalline structure, was 53 to 509 Wm. These coercivity values are not sufficient for bonded magnet applications. From the study of additive effects, it was found that C, C-Si, C-Ga, or C-Al addition decreased the crystal size of quenched Sm2Fe17 powder. Consequently, high coercivity was obtained; the HcI of nitrided Sm2Fe1C1Si1 MS powder with V5 of 10 m/s was 898 kA/m, and 708 kA/m for the nitrided Sm2Fe15C1Si1 RDA powder. The compression-molded bonded magnet made from Sm2Fe18Si0.1Nx MS powder showed a high (BH)max of 82.7 kJ/m3.

Jan 1, 2000

By Carlos Eduardo Gomes de Souza, Luis G. S. Sobral, Paulo A. Medeiros da Silva, Selma G. F. Leite, Renata de B. Lima

"The use of mixed cultures of acidophilus microorganisms that act in different temperature ranges, aims at speeding up the digestion of chalcopyrite, highly refractory sulphide mineral, the major mineral in the flotation concentrate of Caraíba Mining Co., with an attractive processing cost. The concentrate under consideration contains mainly chalcopyrite (CuFeS2) and bornite (Cu5FeS4) with contents of, approximately, 70 and 30%, respectively. It was observed in this study, the performance of consortium of mesophiles, moderate and extreme thermophile microorganisms, in the oxidation of the aforementioned sulphides minerals, evaluating operational parameters such as pH of the leaching solution, the reaction temperature and redox potential, with consequent extraction of 80% of the concentrate copper content within 60 days of bioleaching. Such high copper extraction was achieved in column bioleaching tests.INTRODUCTIONThe solubilization of metals by the application of microorganisms from the mineral ores and the subsequent recovery of metals from solution are referred to as bioleaching (Rohwerder, T et al, 2003). This is an economical method for the recovery of metals from minerals; especially lowgrade ores, overburden, and waste from current mining operations which requires moderate capital investment with operating cost (Watling, 2006).Furthermore, bioleaching is generally more environmentally friendly than conventional metal recovery processes such as concentration and smelting. Those physicochemical metal extraction processes generate sulphur dioxide, a toxic emission that is increasingly the target of regulatory legislation (Stott et al., 2000; Olson et al., 2003). Bioleaching of chalcopyrite is the key industry target. The main problem hindering commercial application of chalcopyrite bioleaching is the slow dissolution rate (Fu et al, 2008).Dissolution of acid-soluble sulphide minerals such as sphalerite, and to a lesser extent chalcopyrite, occurs by a combination of ferric iron and proton attack via the polysulphide pathway (Rohwerder et al., 2003)."

Jan 1, 2008

By Zuoren Huang

The flowsheet of the hyd.rametallurgical zinc plant which is in use at Zhuzhou Smelters is described. The principal features of the process are fluid bed roasting, continuous calcine leaching, solution purification, zinc electrolysis, electrolyte cooling, and finally, the melting and casting of zinc forms. The Zhuzhou process for the flotation of silver from the leach residue collected on the Moor filters is described. The technical details of the process are outlined and the operating data are analyzed. The flotation facilities are described in detail and concentrate grades and recoveries are presented. The waelz process is used to concentrate In, Ge and Ga remaining in the leach residue after silver flotation. These elements subsequently are recovered by selective leaching in sulphuric acid, and details of this operation also are presented.

Jan 1, 1990

By Henrique Hesse, Rosana de Cassia de Souza Schneider, Wolmar Alípio Severo Filho, Ezequiel Bavaresco, Rodrigo Klamt, Luciano Roni Silva Lara, Luciano Dornelles

Alkyd resins are used in surface treatment. They are product of the glycerolysis followed by polymerization. In the present work it was studied methods of alkyd resin production from crude glycerol compared with resin produced with pure glycerol. This glycerol corresponds to 10% of the final products in the biodiesel production. The crude glycerol was partially purified with neutralization, flotation and adsorption. The experiments were accomplished with temperature control, inert atmosphere and with several quantities of the substrate. For the products characterization physic-chemistry methods, infrared spectroscopy and hydrogen nuclear magnetic resonance were used. According to the observed results, the resins obtained with crude glycerol have presented similar properties of the classic alkyd resin produced with pure glycerol. The exploitation of the crude glycerol reduces the stages and costs of the process.

Jan 1, 2008

By Andrew Campbell, Michael Reed

"WorleyParsons has used Discrete Event Simulation methods in conjunction with more traditional process models to assess the performance of copper smelting operations. This work was performed to determine the plant capacities and suitability of proposed debottlenecking options including accounting for the planned and unplanned (breakdowns) shutdowns in the various parts of the plant and supply chain. This paper outlines the methods used along with demonstrating the benefits of selecting a feasible option and minimizing capital and operating costs.IntroductionTraditionally for de bottlenecking studies of smelters and other process plants, a mass balance is performed based on continuous operating rates and expected operating hours. Smelters have several points of failure that will restrict, if not take the entire plant offline. By using a more detailed model, validated against plant experience, bottlenecks can be demonstrated and strategies to remove them to increase plant availability and economic.The modeling simulates the plant performance in real time, and by performing enough simulation the expected long run performance of the plant can be estimated. The models have been built using ExtendSim which is a powerful Discrete Event Simulation software package that is ideally suited to the batch and semi-batch processes and events that occur within smelter operating environments. The value of performing this work is that the operational performance of the plant can be assessed ensuring production targets are met, without using excessive capital outlay."

Jan 1, 2013

By M. A. Barakat

Large amounts of zinc ash and flue dust containing more than 80 % zinc are accumulated during galvanization processes at the surface of molten zinc bath and in the chimney respectively. Pyrometallurgical recovery of zinc from both of the ash and dust samples has been carried out. The ash was sieved with the help of an industrial sieve shaker provided with mesh sieve having a pore size 0.9 mm. The oversize fraction cut (+ 0.9 mm) was melted at 550 °C under ambient conditions. The produced ingot (1) was analyzed whereas the coarse fraction of the produced slag (+ 0.9 mm) was treated as the coarse ash or added to it. The dust was enriched with suitable fluxing salt prior to heat treatment at 600 °C for 1 h. The produced ingot (2) was analyzed whereas the resulting slag was mixed with the fines of the ash and treated by hydrometallurgical processing to prepare valuable salts of zinc. Parameters affecting recovery processes such as time, temperature and flux percentage were studied. Results obtained revealed that the two prepared ingots (1&2) were successfully recovered with recovery efficiency amounts to =85 %. The obtained samples meet the standard specifications with relatively low price. Also in the light of the strict environmental regulations of pollution control, reuse of these wastes materials will help in keeping the environment clean.

Jan 1, 2000

By Manfred K. Walther

"Tests were conducted on instrumented plates cast in the Abex Experimental Foundry to compare recorded solidification histories with results computed for corresponding models simulated with the C.A.S.T. program. The first plate was cast of low alloy steel and the second of carbon steel with a graphite chill at one end. Both were cast in molds of bonded silica sand. Temperature histories were recorded in the castings, molds and chill. Exceptionally good agreement was achieved between computed and experimental data. Other investigators will find the results useful as a benchmark against which they can compare the results of their own calculations.IntroductionSince the early 1970's our foundry engineers have used both two- and three-dimensional versions of the G.A.S.T. program to gain knowledge of the solidification process [1,2,3]. Study of the computed data gave insight as to how the rigging and risering of specific castings might be changed or adjusted to improve quality and yield. New schemes based on such analyses were then recommended for implementation on the foundry floor. The degree of success of the new practice was subsequently evaluated after the part had been poured, shaken out and examined. Similar conditions were noted in the sectioned castings whenever porosity and voids had been predicted by the computations. Appropriate modifications, when found successful in the model, were applied to the process. This led to a reduction, if not complete elimination, of the defects. Such results gave credence to the use of these programs as an aid in the production of better castings.Earlier investigations on simple shapes revealed excellent correlation between output derived with the G.A.S.T. program and exact solutions. Results also compared favorably with data calculated using other codes as reported in the literature [4] and summarized in the Appendix. However, since the computer program had not been verified by direct experiment, it was decided to run instrumented tests to check the theoretical predictions with actual measurements."

Jan 1, 1986

By Ian F. Hughes

"Concepts of an integrated steel plant for sheet products to be built and operating in the year 2000 will be described. The design and operating methodology of this market driven facility will integrate process uniqueness, standardization, manufacturing automation, artificial intelligence and information flow.An integrated steel plant for the year 2000 is defined for this article as one that will be built on a greenfield site and ""started up"" in the year 2000 with a capacity of three million tons per year of flat rolled products ranging from cold rolled and electrical steels to high strength formable steels and a full range of coated products.It may seem that the 21st century and the steel plant we're discussing are far into the future. The startling truth, however, is quite the opposite. As shown in Figure 1, even with accelerated development, a new process on which laboratory development work is begun today might just barely pass through the laboratory phase, pilot plant, and commercial feasibility stages such that it can be considered viable for construction and start up in the year 2000.On that basis, it is very unlikely that this 21st century steel plant will utilize any technology that isn't at least under investigation in the laboratory in 1988. As a result, we recognize that planning and selecting the facilities for this plant is, in fact, a pragmatic rather than futuristic process, and that its main value is in providing a bridge to longer-term predictions."

Jan 1, 1988

By LuisW. Pommier

The industrial wastes generated by the plating industry, the circuit board manufacturing industries and other related industries normally contain high concentrations of metals, which make them hazardous. The extraction of the contained metals and their separation may be achieved by both pyro and hydro metallurgical processes. Some of the industrial wastes, those rich in some metals like nickel for instance, are being treated like mine ore concentrates and are being fed to smelting furnaces. The slags from these smelter operations are hazardous. They have, however, special environmental dispensations issued by the regulatory authorities. Hydro-metallurflcal processes have been reported. They also generate a residue which is hazardous because not all the valuable metals are leached out and also, because "non valuable" components, like chromium, are less readily leached. Residues from the plating industry, containing nickel, copper. zinc, iron and chromium as the major constituents and also sodium and calcium, together with cadmium, cobalt, lead. manganese, magnesium, molybdenum, and potassium, have been processed for the extraction of the valuable components. The generation of electrolytic nickel, copper and zinc and also of ferric chloride and chromium oxide is reported. The operation is achieved by a caustic leach for the extraction of zinc, followed by a sulfuric acid leach for the extraction of nickel and copper. This acid leach also extracts the iron and some chromium. The nickel copper and zinc are rendered pure by electrolysis, the iron is oxidized for the production of ferric chloride and the chromium is recovered as an oxide. The leaching operation is performed in two stages, first at a pH of 2.5 to generate an electrolyte for the partial recovery of the metals and then at a pH of 0.5 for the complete extraction of the metals. This leaching operation generates a residue, which although small in volume compared to the initial feed, still contains traces of the valuable metals and a portion of the chromium which makes it hazardous. Additional leaching with hydrochloric acid or nitric acid is required for its complete dissolution. The other minor constituents mentioned are present in concentrations each of less than 0.1% and are handled as impurities in the process. The metals which are soluble at a pH 0.5 and precipitate between 0.5 and 2.0 are bled off. Other impurities will concentrate on the raffinate from the solvent extraction operations from whence they are bled off. These bleeding streams are hazardous and the "impurity metals" are now present in concentrations which would make them valuable, however, the size of these streams is so small that they do not warrant their processing, however they could be marketed to specialized smelters. The extraction of the valuable metals, of the hazardous constituents, the generation of a marketable mixture of minor constituents and the production of a non-hazardous residue for declassification is profitably achieved.

Jan 1, 1998

By Luis W. Pommier

The wastes of the plating industry are generated in the process of rinsing the plated objects and during the cleaning of the plating shops. High volumes of hazardous waters are neutralized on site producing recyclable water, generating a metal rich, hazardous, filter cake. Occasionally, a complete plating bath has to be discarded which increases the metal content of the filter cakes. These filter cakes are discarded as hazardous at a cost of over $ 250 per ton. The metals found in the cakes are generally copper, nickel and chromium or zinc, lead and cadmium, assaying from 2% to 15% or even higher content of each metal The metals and their contents are highly variable. Some plating shops discard their products directly to hazardous waste sites, others, have them collected by companies which consolidate wastes from several producers prior to discarding. These wastes, richer in metal content than mine ores, need neither mining nor crushing and grinding for concentration. The commonly found impurities in the mine ores, i.e.: pyrites, arsenic, and valuable metals which are present in minute quantities, are absent in the filter cakes. The processes available to selectively recover the metals from the filter cakes, are discussed based on their technical and economic merits. The flow-sheets include leaching, solvent extraction when required, and electrolytic refining. Examples, showing the separation of copper, nickel and chromium and also of zinc and lead in pilot plants, show the technical and economic viability of the processes.

Jan 1, 1996

By P. K. Jimack, C. E. Goodyer, A. M. Mullis, P. C. Bollada

"We review the application of advanced numerical techniques such as adaptive mesh refmement, implicit time-stepping, multigrid solvers and massively parallel implementations as a route to obtaining solutions to the 3-dimensional phase-field problem with a domain size and interface resolution previously possible only in 2-dimensions. Using such techniques it is shown that such models are tractable even as the interface width approaches the solute capillary length.IntroductionMulti-scale modelling impinges upon many areas of science, engineering and technology where the interplay between processes occurring on disparate length and/or timescales can affect the properties of systems in a complex, and sometimes unforeseen, manner. One such is the processing of materials where interactions at the atomic scale, through the nano- and microstructural scale can have a profound affect on the macro-scale response of engineering components. Here we focus on one such problem, the crystallisation of alloy melts, to illustrate how a range of advanced numerical techniques make the modelling of such systems tractable.The modelling of solidification structures, in particular the growth of dendritic crystals, is a subject of intense and enduring interest within the scientific community, both because dendrites are a prime example of spontaneous pattern formation and they have a pervasive influence on the engineering properties of metals. For alloy systems, which form the vast majority of engineering materials, solidification involves the rejection of both solute and latent heat from the growing solid, forming a coupled diffusion problem in which both the chemical and thermal diffusion equations should be solved. The multi-scale nature of this problem arises from the disparity between the thermal and solutal diffusivities for most liquid metals, which are typically 10-5 m2 s-1 and 10-9 m2 s-1 respectively. The ratio of these two, referred to as the Lewis number (Le =Dia), is therefore typically of the order 10,000 and gives a measure of the multi-scale nature of the problem. In fact, in many cases the thermal diffusivity is so much larger than its solutal counterpart that thermal diffusion is considered instantaneous, wherein the system can be approximated as isothermal such that the multi-scale calculation does not need to be performed. This is certainly a reasonable approach in most conventional castings. However, there is a class of solidification problem in which this approach is far from satisfactory, namely Rapid Solidification (RS). The application of isothermal phase-field models in such situations are highly likely to produce spurious results or to fail totally, particularly for temperatures below To (the temperature at which the free energies of the solid and liquid phases are equal at the concentration of the bulk alloy), wherein partitionless solidification may occur."

Jan 1, 2013

By F. M. Nakla

Various methods of Applied Mineralogy were used for determining the nature and composition of products yielded by flotation tests for Maghara coal beneficiation. Coal samples obtained from the Sa fa mine in Northern Sinai, Egypt, were crushed, sieved, &apos;and <32 mesh size fraction was cleaned by froth flotation. Experiments were conducted to determine the effect of certain parameters on beneficiation of Maghara coal by flotation. The investigated factors included nature of frothing and/or collecting reagents, pH value of the medium, particle size distribution in the head sample, and pulp density of the coal slurry. The quality of head samples, coal concentrates, and tailing products were determined by chemical analysis, microscopic study, x-ray diffraction analysis, and occasionally by infrared (IR) absorption spectroscopy.

Jan 1, 1989

By Reimers. Jan H.

Practically all the world&apos;s lead is produced by sintering and blast furnace smelting, or the Imperial Smelting Process which is a variant of the blast furnace process. Increased coke and labour costs and strict lead emission limits have, however, made blast furnace smelting undesirable in most countries. A change-over to other lead smelting processes providing better working conditions and lower emissions is, therefore,. expected to occur once economic conditions improve and the necessary capital expenditures can be justified. The need for new lead smelting processes has long been evident and a number of new processes have been proposed &apos;and advanced to various stages of development. One of the new processes is already proven on commercial scale, while several others are still being tested on pilot plant scale.

Jan 1, 1983

By Deepu Philip, Pratik Agarwal, Ajay Kumar Shukla, Ishani Shukla, G Rajesh

Steel plants generally employ static BOF end point control models to arrive at a given temperature and chemistry at the end of blow. These end point models have now been supplemented with chaos control models to steer the blowing process in the right direction while the blow is in progress. Merely arriving at the correct end point temperature is however not adequate because in the subsequent stages as well the temperature variations can be large and unpredictable. The present paper deals with an integrated model to take into account the effect of all parameters affecting temperature and composition from tapping to the start of casting to minimize the use of LF or aluminum heating, and also minimize grade mixing. The application of lean operations strategy is explained in which the previous “Push System’ is changed to a “Pull System”, minimizing the use of ladle furnace or aluminum heating during steelmaking.

Jan 1, 2014

By B. Manana

In heap leaching, the oxidative dissolution of value minerals encapsulated deep within large particles cannot be fully understood on the basis of the bulk solution conditions relative to variable solution conditions near the mineral surface. In the present study, the diffusion of the oxidising species through inner particle pores is simulated in a model apparatus that separates an inert platinum electrode under controlled reduction potential from the bulk solution through narrow pores of varying length. The Cu-NH3 system was selected as a model system and Cu(II)/Cu (I) as the redox couple of interest. Platinum probes inserted in the pores allowed the measurement of varying redox potentials along the pore length. Results showed that in a 10 mm pore, there exists a narrow (0.5 mm) zone near the reduction surface that is depleted of the oxidant and in which its supply is strongly diffusion limited, even if it is in abundance in the bulk solution. The consistent presence of this narrow diffusion region across all experimental results indicated that the transportation of the reduced species away from the reaction surface had the most significant influence on the potential variations within the pore. This was further supported by the minimal effect of varying concentrations of both Cu(II) and dissolved oxygen on the solution potential within this region.

By Stéphane Bourg

The SCRREEN project gathers more than 50 European initiatives, associations, organisations or independent experts working on Critical Raw Materials (CRM) into a long-lasting network including stakeholders, public authorities, and civil society representatives. SCRREEN contributes to improve the CRM strategy in Europe by (i) mapping primary and secondary resources and substitutes of CRMs, (ii) estimating the expected demand of various CRMs in the future and identifying major trends, (iii) providing policy and technology recommendations for actions improving the production and the potential substitution of CRM, (iv) addressing specific waste electrical and electronic equipment (WEEE) and other End-of-Life (EoL) product issues related to their mapping and treatment standardization, and (vi) identifying the knowledge gathered over previous years and making the data accessible to those beyond the project. As a first step, SCRREEN worked at providing stakeholders with a comprehensive analysis of the current use of the CRM, the mapping of potential primary and secondary resources, and identification of the key technologies used in their production. Substitution profiles, analysis of European business and policy issues pertinent to CRMs, and an identification of the standards, policies, and regulatory frameworks concerning these CRM was also completed. In a second step, to be conducted between mid-2018 and mid-2019, SCRREEN will provide guidance for improving the CRM market in Europe by identifying opportunities from research, development, and innovation (R&D&I) that could reduce the supply and/or economic risks around the most relevant CRM for Europe.