Search Documents

By Iain B. Mackenzie

In 1997, a thin layer of Microtherm Microporous Insulation was used to replace fireclay brick behind the magnesia/chrome working lining in #5 refining furnace at BHP?s San Manuel AZ smelter. A 23°C reduction in shell temperature was obtained, together with a large increase in the working capacity of the vessel. There was no sign of metal penetration as a result of the increased insulation. Following these highly favorable results, BHP have introduced this product into all of their refining furnaces.

Jan 1, 1999

By David B. George

Kennecott recently completed an $880 million modernization and expansion of its smelter and refinery to process all concentrates from the Bingham Canyon mine. This is the first application of Kennecott-Outokumpu Flash Converting. Molten material movement by overhead cranes is eliminated and high levels of oxygen enrichment result in very low process gas volumes and exceptionally control of sulfur oxide emissions. All existing in-plant hygiene, safety, and environmental regulations will be met and the smelter is positioned for anticipated more stringent future regulations. Sulfur capture is 99.9 percent resulting in sulfur dioxide emissions less than the 112 kg/hr Air Permit limit, making the smelter the cleanest in the world.

Jan 1, 1996

By T. J. Weitz, J. E. Micheletti

"Pegasus Gold's Beal Mountain Mine is located near the Continental Divide, SW Montana. Conventional surface mining utilizes crushing, heap-leaching, carbon absorption/desorption, electrowinning and refining to produce approximately 60,000 oz gold annually. A leach pad sits at 2,300 meters (7,500 ft) elevation. Winters are long and cold with average snow accumulations ofl-2 meters; temperatures fall below minus 40'C and wind chill temperatures below 70°C. The Beal Mountain staff has developed special tools and procedures for burying drip emitter lines, and managing the heap and process solutions to allow for uninterrupted gold recovery during the winter season. Management of water balance and spring runoff is critical to the operations' success, due to mountainous terrain, high precipitation and proximity to a fishery and elk herd. The mine has an extensive network of land application disposal (LAD) and stormwater control systems to assure environmental protection and regulatory compliance.ABSTRACT ONLY"

Jan 1, 1997

By A. V. Tarasov

An environmentally clean and virtually waste-less technology for treatment of domestic solid waste and other toxic chloride-containing materials has been developed and proven on a full scale by the Gintsvetmet Institute in cooperation with some other Russian organizations. The proposed process resolves the acute and globally significant problem of dioxin formation. The purpose of the proposed technology is to ensure such destruction of the structural lattice of toxic compounds that would guarantee irreversible transformation of the resultant substances to prevent formation of dioxins. The preconditions that are required to achieve this purpose are: temperature of >125O0C; an oxidant excess coefficient of >I .05; a certain retention time of the products under these conditions (ADZ s); and thermal instantaneousness of the process involving a transition with no intermediate phase. These conditions were achieved with the experimental development of the Vanyukov furnace design commonly used for sparged smelting processes at non-ferrous metallurgical plants in Russia and Kazakhstan.

Jan 1, 2002

By Norihiro Murayama

The hydrothermal syntheses of zeolites from coal fly ash were carried out using NaOH and KOH as an alkali source. The cation exchange capacity (CEC) and the ion exchange selectivity were investigated for the zeolites synthesized by a hydrothermal treatment. The effective usage of the zeolite as a cation exchanger was considered from the viewpoint of engineering. Zeolite P, HS (hydroxysodalite) and K-CHA (potassium-chabazite) are mainly formed as zeolite species in NaOH or KOH solution at 393K. The zeolite P and K-CHA have a large exchange capacity as a cation exchanger. The cation exchange isotherms of various monovalent and divalent cations with various zeolites are investigated. The order of selectivity of the zeolites is as follows, NH4+> K+> Li+.For the divalent cation, the largest removal amount is obtained for Pb2+ in the low equilibrium concentrations below 0.2mmol/dm3, and almost perfect removal can be achieved for Pd2+. The order of selectivity of zeolites in low concentration is expressed in the following order; Pb2+> Co2+> Cd2+> Ca2+> Mg2+> Ni2+. Ii is considered the zeolites obtained from coal fly ash can be used as an excellent cation exchanger.

Jan 1, 2006

By William Petruk

The behaviour of sphalerite during mineral beneficiation of base metal ores has been studied at CANMET and other institutes for at least 15 years by determining the liberations of sphalerite in mill products and calculating the recoveries of liberated and unliberated sphalerite in zinc concentrates. Sphalerite in base metal ores commonly occurs as layers and as interstitial material between pyrite. Layered sphalerite is generally liberated during primary grinding, but interstitial sphalerite requires re-grinding to achieve liberation. Around 95% of liberated sphalerite is generally recovered in zinc concentrates frau zinc circuit feeds. A series of tests was conducted on sphalerite in the ore of Brunswick Mining and smelting during a continuous fine tuning operation of the concentrator. It was found that a grind of 80% minus 37 micrometres was required to liberate the interstitial sphalerite. The fine grind increased Zn recoveries from 75% to 78-80%, but produced liberated slimed sphalerite which was lost. Since regrinding to a fine grain size is needed to obtain the desired sphalerite liberation, a method of recovering the slimed sphalerite is required.

Jan 1, 1990

By Robin D. Rogers

Room temperature ionic liquids (RTIL) can replace certain traditional organic solvents in liquid/liquid extraction of metal ions from aqueous systems. The very low vapor pressure and non-flammable nature of RTIL warrant consideration of these neoteric solvents for new processing technologies which will reduce pollution, Increase safety, and lower costs. Metal ion separations in RTIL, however, will typically require the use of an extractant and research is needed to identify suitable selective extractants which have appreciable solubility in the RTIL and low solubility In the aqueous phase. Choice of extractant should also take into account the toxicity, expense, and disposal of the ligand.

Jan 1, 1999

Lance based copper-nickel matte converters have become an established technology in the field of base metal sulphide smelting and converting. An Ausmmelt® converter is currently being constructed at Anglo Platinum in South Africa to convert a nickel-copper rich matte containing platinum group metals (PGM's). The accurate prediction of the matte chemistry is required to control the composition at the endpoint which influences segregation of PGM's during the subsequent slow cooling and magnetic separation processes. A hybrid modelling approach is introduced in this paper that incorporates both the effect of thermochemistry and system dynamics. It will be shown how the model relates to fundamental conservation laws, while still providing enough flexibility to adapt to changing operating conditions. It will also show how off-line modelling can be incorporated into a robust on-line model. Based on the data from many pilot plant trials, the model prediction performance is shown to be within the accuracy requirement set by industry and therefore constitutes a reliable basis for model based control. The final generic model structure takes on the form of an thermodynamically integrated ARMAX hybrid model. The final model has the advantages of being dynamic, adaptive, robust and it can be related to thermochemical fundamentals.

Jan 1, 2002

By Tang Chaobo

According to the principles of simultaneous chemical equilibrium and electronic charge neutrality, the system of Mg(II)-NH3-CO32--SO42--H2O at 25°C has been thermodynamically analyzed. And the rule of solubility of MgCO3(s) in the system is discovered, the high dissolution field of MgCO3(s) is discovered too. Furthermore, the solubility of MgCO3(s) is increased with the increase of the concentration of SO42-, but it is decreased first then increased with the increase of the concentration of all the CO32- and the total concentration of ammonia and ammonium, and decreased with the value of pH being higher. Those results will has important significance on prepare magnesium chemical products and other salts carbonate that are strict with the content of magnesium with carburization method.

Jan 1, 2006

By Francis Vanbellen

Umicore Precious Metals Refining operates an integrated precious metals smelting and refining plant in Hoboken, Belgium. Once a smelter and refiner of complex concentrates, the plant today?s feed consists exclusively of industrial and consumer recycled products, making it the world?s largest recycling facility for precious metals. Unlike the fairy tale of the Frog Prince, it took much more than a princess? kiss to successfully realize this makeover. A completely renewed plant has been built over the past decade. The most visible technological innovation was the commissioning of the Pb-Cu smelter. Its flexibility towards very different types of feed makes it perfectly suited as main entry to the Hoboken flow sheet. A new Cu-leaching & electro winning plant and precious metals refinery make up the Precious Metals Operations (PMO) whose targets are fast throughput and maximized yields for gold, silver and the platinum group metals. The Base Metals Operations (BMO), flexibly process the by-products from the PMO, valorizing ?impurities? like indium, tellurium, selenium and others. Off gas and waste water treatments ensure compliance with strict environmental standards. Precious metals recycling is an art that goes beyond mastering a unique flow sheet. Umicore Precious Metals Refining offers a complete recycling service, taking care of sampling and assaying, metals management and logistics. The quality of this integral service is recognized through the attribution of ISO certifications for our operational activities, sampling and the environmental care. And it?s an art that follows Michelangelo?s experience: ?Art is 5% of inspiration and 95% of transpiration.?

Jan 1, 2006

By Mieke Campforts

The usefulness of the water-cooled probe technique to experimentally study slag solidification and freeze lining formation in pyrometallurgical reactors is evaluated. With this technique a layer of solidified slag is formed on a water-cooled probe that is submerged into a liquid slag bath. The influence of the submergence time and the heat input is examined. The solidified layers are analyzed with light microscopy, electron microscopy, electron probe micro-analysis and X-ray diffraction. Thermodynamic software is used to interpret the solidification microstructure. The results demonstrate that the technique is useful to understand freeze lining formation.

Jan 1, 2006

By Shujian Jia, Mingming Song, Gaoyang Song, Bo Song, Yuhou Yang

An innovative method is investigated to separate inclusion particles from liquid metal by super gravity. To make clear the characteristics of the inclusion separation, Al melt containing MgAl2O4 particles with diameters less than 150 μm has been treated under various super-gravity fields. The thickness of particle-accumulated layer formed at the bottom of the sample and the area fraction, number density and size of inclusions were measured. It is found that the thickness of the particle-accumulated layer decreases and the area fraction of particles at this location increases with the increase of super-gravity field. With the gravity coefficient G=500, time t=2 min, and temperature T=1023 K, it is hardly to find any solid particles in the upper and middle areas of the sample and the separation efficiency is up to 90%.

Jan 1, 2015

By Giovanni Principi

The activity of the ?Hydrogen Group? of Padova University, addressed to the study of materials for solid state hydrogen storage, is illustrated. Various Mg-based materials have been considered and are being studied: a) MgH2 and 0.5% mol Nb2O5 mixture ball milled under argon atmosphere; b) Mg-Ni-Fe intermetallic compounds prepared by short time ball milling of ribbons obtained by melt spinning and by long time ball milling of a mixture of MgH2, Ni and Fe powders; c) MgH2 ball milled in argon with Mm-Ni-Al (Mm = La-rich mishmetal) and Zr-Cr-Fe catalyst alloys. All the samples have been structurally characterized by X-ray diffraction (Rietveld refinement) before and after hydrogen absorption/desorption cycling and tested with a Sievert apparatus as regarding their thermodynamic and kinetic properties.

Jan 1, 2006

By A. G. Guézennec

Electric Arc Furnace (EAF) steelmaking co-produces amounts of dust (15 to 25 kg per ton of steel), which require to be collected and stored in specific landfills. The collection, handling, and possible beneficiation of EAF dust depend on its composition and morphology. We first studied theoretically the chemical evolution of dust particles along the fume extraction system, from the furnace down to the filters, using thermodynamic calculations of the Fe-Zn-O system. We show how it would be possible to favor zincite formation in dust and therefore increase further zinc recovery. Then, we developed a new morphological model, based on population balances, for predicting the granulometric evolution of dust particles as a result of agglomeration and sintering in the fume extraction ducts. The contribution of the various mechanisms (Brownian, turbulent, and sedimentary agglomeration; thermophoretic deposition; coalescence and sintering) is assessed. The influence of the exhausting conditions on dust granulometry is detailed. For the extraction system studied, intense agglomeration of the sub-micronic particles and complete coalescence take place inside the furnace; micronic particles then undergo little evolution from the elbow to the water-jacket, whereas big agglomerates are formed downstream. These results are in good agreement with dust particle observations.

Jan 1, 2006

By Mark William Kennedy

"Electric furnaces containing high quantities of slag are applied in many areas of pyrometallurgy, often for smelting or slag cleaning. A variety of ratios or rules of thumb have been employed in the industry for the dimensioning of these vessels, in most cases with no clear technical basis.In this paper, several design guidelines are presented (electrode size, spacing, vessel dimensions, energy intensity, etc.) as an attempt to provide some technical basis for optimal dimensioning.Furnace heat generation is related to side wall copper cooler heat losses, in an attempt to establish a methodical design strategy particularly for minimum electrode to wall spacing for modern furnaces with cooled linings.Issues regarding the true nature of heat production in a slag furnace are discussed with regards to the possible impact on accurate modeling and design.IntroductionSlag furnaces have passed through a number of design 'generations' characterized by increasing energy intensities, improved electrode technologies and advancing development in their physical structure or 'furnace integrity' as shown in Table I f 1]. A 3rd generation furnace using ultra-high-power (UHP) graphite electrodes is shown in Figure 1, as a generic example of the types of physical structures present in modern slag furnace designs [1]."

Jan 1, 2012

By Jian Li

Corrosion resistance of materials is highly dependent on the microstructure of the specific material. Apart from general corrosion rate measurement using techniques like linear polarization and A.C. impedance, microstructural investigations are frequently needed to identify the root cause of corrosion. Advanced techniques, including scanning electron microscopy (SEM) and transmission electron microscopy (TEM), have been well integrated into routine characterization studies. Other microscopy techniques, including electron probe micro-analyzer (EPMA), Auger, X-ray photon spectroscopy (XPS) and secondary ion mass spectroscopy (SIMS), can provide detailed chemistry information on corrosion products. In recent years, focused-ion beam (FIB) microscopes have evolved into an important microstructural characterization instrument. In this study, corrosion of rebar encased in concrete was studied in great detail using advanced microscopy techniques. Corrosion product on the rebar surface was identified as ferrous oxide with relatively large crystal size. The morphology of this passive layer was thoroughly analyzed, and its formation mechanism is proposed.

Jan 1, 2009

By Andreas Weber

Batrec operates a plant for the recycling of used dry batteries with a capacity of 3000 tons per year. The plant Is situated In a tourist area of Switzerland and has complied with all the strict emission restrictions. The process yields four products: FeMn. Zn, Hg and slag. No hazardous waste Is produced. All types of batteries can be treated.

Jan 1, 1995

By Tao Li

The development of DP(Dual Phase) steels and TRIP(Transformation Induced Plasticity) steels has received much attention in recent years due to their high strength and simultaneous good ductility, which provides the potential for weight reduce and resource savings on certain components in automobile or other industries. So a controlled rolling process was simulated in the present study by thermomechanical simulator (Gleeble 1500) for producing DP steels on a kind of low carbon steel containing a small amount of Si and Cr. F+M dual phase microstructures have been obtained during continuous cooling processes of a wide cooling rate range from 10°C /s to 60°C /s. The grain size of the dual phase steel developed can be refined to less than 5 m through the mechanism of deformation induced ferrite (DIF) transformation. The ultrafine ferritic grains are equiaxed with high-angle boundary, and the martensite islands of an average size less than 5m disperse uniformly in the ferrite matrix. The ultrafine martensite islands not only inhibit the growth of ultrafine ferritic grains and improve the bonding of F/M interface, but also increase remarkably the strain hardening rate in the processing of the present Dual-Phase steel. As a result, the tensile strength of ultrafine grained Dual-Phase steel reaches higher than 1000 MPa. The result shows that an ultrafine grained Dual-Phase steel of low carbon and low alloy is promised to exhibit desired F+M microstructure by means of this new TMCP process.

Jan 1, 2006

By Ana E. Bohé

Chlorination process is an attractive and efficient method for the metal recovery from complex materials. The process that is performed at high temperatures, allows converting all the metals contained in the material into their respective chlorides which are further separated in a selective way. Aluminum metal matrix composites with discontinuous ceramic reinforcement of short fibers, whiskers, and particles have been gaining wide acceptance as an important engineering material in automotive, aerospace, and electronic industries. Since the ceramic reinforcements are still quite expensive and contribute significantly to the final cost of composite materials, the feasibility of their recovery from the manufacturing scrap and further recycling is a factor of increasing economic interest. In the present work, a theoretical and experimental study is given for the recovery of Al2O3 and SiC particles and short fibers from three commercially available aluminum-matrix composites produced by molten metal mixing route. The process consists of transforming the constituents of metallic alloy matrices in gaseous chlorides that are dragged by the gaseous stream, while the ceramic reinforcement remains as a solid residue in the reaction bed.

Jan 1, 2006

By Jin Zuomei

The kinetics of dissolution of nickel matte in the presence of manganese dioxide with silver ions was investigated. The catalytic silver ions enchanced the leaching rate up to a factor of 17. The effects of stirring, temperature, particle size, concentrations of Mn02, silver and ferric ions, and the experimental procedures were studied. Solid residues at various levels of nickel extraction were examined by SEM, TEM, electron micoprobe and X-ray diffraction. These results indicated that the dissolution reaction was topochemical and fits a surface reaction control model. The activation energy was calculated to be 39.15 KJ/mol. The leaching rate of Ni3S2 was independent with stirring rate, but the reaction rate constant was inversely proportional to the initial particle diameter. The order of the reaction rate are 0.41, 0.69, 0.33 with respect to Ag+, Mn4+ and Fe'+ con-centration respectively. Thus a kinetic rate equation was developed. Moreover, we propose a mechanism of silver catalyzed leaching of Ni3S2'

Jan 1, 1990