Search Documents

By P. N. Anyalebechi

A comparative study of the mechanical properties of automotive steering knuckles produced by three different shape-casting related processes has been conducted. It involved the characterization of the tensile and fatigue properties of aluminum alloy A356 knuckles produced by the vacuum/pressure riserless casting (VRC/PRC), pressure counter pressure casting (PCPC), and the hybrid Cobapress (a casting-forging) processes, in accordance with the appropriate ASTM standards. Surprisingly, the knuckles produced by the hybrid Cobapress process exhibited the lowest strength. For example, the average 0.2% yield strength of the Cobapress knuckles was 31 MPa and 40 MPa less than that of the VRC/PRC and PCPC knuckles, respectively. However, between stresses of 150-200 MPa, the fatigue lives of the VRC/PRC, PCPC, and Cobapress knuckles were comparable. But above 200 MPa, the Cobapress knuckles exhibited the lowest fatigue life. The observed differences in the mechanical properties are attributed to the inherently different microstructures of the different knuckles.

Jan 1, 2009

By J. C. Huyhua

The effect or various oxidants on gold and silver dissolution in thiourea solutions (0.05 M in H2SO4) was studied using the rotating disc technique, a.t 2s c and 600 rpm. These studies were carried out at constant (4:1) initial molar ratio or thiourea to oxidant concentrations, to produce 50 % thiourea. oxidation. The initial dissolution rate of gold was approximately four times higher in the presence. of ferric sulfate (5.37 x 10-3mg cm-2 s-1) than in the presence of hydrogen peroxide (H2O2), potassium persultate (K2S2O3), or monopersulfa.te (KHS06). The dissolution rates for silver were considerably lower than gold for the same oxidants. Oxidation of thiourea in the presence of peroxygen and persulta.te compounds is a. fast reaction and it is completed in less than ten minutes. On the other hand, the oxidation or thiourea with? ferric.sulfate is slow, yielding a second-order reaction rate constant k = 6.09 I mol-1 h-1. Sulfur formation in the ferric thiourea system begins when ferric ion reduction approaches to completion. With hydrogen peroxide, sulfur is observed at lower thiourea concentration than ferric. Suifate. The presence of a large excess or free thiourea i.e., s to 20 % thiourea oxidation) retards sulfur formation and maintains favorable dissolution rates. Finally, carbon-in-leach experiments indicate that thiourea solutions a.re stable for several days, with ferric sulfate or hydrogen peroxide. The dissolution rates of gold and silver doubles in the presence or activated carbon when hydrogen peroxide is used as oxidant.

Jan 1, 1989

By Sayavur Bakhtiyarov

Keywords: Rheology, Viscoelastic, Oil In this paper we present the results of the rheological property measurements on viscoelastic composite materials used in oil industry. Laboratory experiments were carried out to determine important thermophysical, rheological and mechanical properties of the test materials using both the standard commercial and in-house made equipment. The composites with the paramagnetic particles (?-iron oxide) are exhibited a significant magnetic memory after magnetic treatment. The measured value of the yield stress after the magnetic treatment increased almost twice in comparison with the yield stress value of the magnetically untreated composite. The yield stress of the composite material exponentially decreases with time and reaches its magnetically untreated value after 15 hours. The yield stress also increases with the amount of the paramagnetic powder additive, and it reaches a maximum value at 8 wt-% of this additive. The obtained results provide valuable information for computer modeling of the viscoelastic fluid flow in pipes of complex geometry.

Jan 1, 2005

By Qingzhu Li

The brewing industry byproduct, spent grain (SG), was evaluated for its ability to adsorb Ag(I) from aqueous solutions. Ag(I) adsorption was dependent on solution pH, contact time, adsorbent dose, initial Ag(I) concentration and temperature. The kinetic data were well described by pseudo-second-order kinetic model, indicating that chemical adsorption was the rate-controlling step. The equilibrium data followed Freundlich isotherm rather than Langmuir isotherm, suggesting heterogenity of the adsorption sites on spent grain. Ag(I) desorbed from Ag(I)-loaded spent grain was also evaluated in this study. HCl, NaOH, Na2S2O3 and ultrapure water were chosen as eluants and desorbed Ag(I)-loaded spent grain for 30min, Ag(I)-loaded spent grain desorbed in 0.1M Na2S2O3 exhibited higher elution efficiency as compared with other eluants. The results indicated that application of spent grain for adsorption and recovery of silver from aqueous solutions was feasible.

Jan 1, 2009

By Pengfu Tan

A thermodynamic model of KIVCET lead smelting process has been developed. The model has the capability to predict the distribution behaviors of Pb, Zn, Fe, S, O, As, and heat balance in KIVCET direct lead smelting furnace. The compositions of lead bullion, matte, slag and gaseous phases, and heat balance are calculated. The effect of the ratio between oxygen and feed on the chemistry of the smelt and heat balance of the coke checker has been simulated and discussed. The thermodynamic model also helps to understand the tapping issue of the lead bullion. In this paper, some applications of this model in the industry have been presented.

Jan 1, 2006

By Junli Xu, Xianwei Hu, Kaiyu Xie, Liangxing Li, Zhongning Shi, Zhaowen Wang, Bingliang Gao, Aimin Liu

Al-Ti master alloys were prepared by aluminothermic reduction between the dissolved titanium dioxide and aluminum in cryolite melts at 960oC. The kinetic analysis by differential scanning calorimetry indicated that the apparent activation energy of the reaction of reducing titanium dioxide by aluminium is 22.3 kJ/mol, and the reaction order is 0.5. The products were analyzed by means of X-ray diffraction, X-ray fluorescence, scanning electron microscopy and energy dispersive spectrometer. Results from X-ray diffraction showed that the phase compositions of produced alloys are Al and Al3Ti. In addition, Al-Ti master alloys containing 2-6 mass% Ti were formed at different reduction time of 2-5h in aluminothermic reduction experiment.

Jan 1, 2015

By Daniel Bennett

There are few methods currently applied towards on-line bulk mineralogical analysis. Yet on-line knowledge of process mineralogy could potentially provide large benefits, such as increased extraction efficiency or resource optimization. The work described in this paper involves the development of radio frequency methods for bulk mineralogical analysis. Some resonances that occur in the radio frequency spectrum are mineral specific, and potentially allow quantitative estimation of mineralogy in an ore stream. Results will be presented on the specific detection of chalcopyrite. Initial quantitative measurements investigating matrix effects have indicated the feasibility of on-line mineralogical estimation using radio frequency techniques.

Jan 1, 2006

By Hirokazu Narita

Keywords: solvent extraction, precious metals, thiodiglycolamide, rapid separation, hydrochloric acid The solvent extraction of some precious metals (Pd(II), Pt(IV), Rh(III) and Au(III)) and base metals (Fe(III), Cu(II) and Zn(II)) in a hydrochloric acid solution was carried out using N,N'-dimethyl-N,N'-dioctyl-thiodiglycolamide (MOTDA) dissolved in the mixed solution of 80 vol-% dodecane and 20 vol-% 2-ethylhexanol. The extraction percentages of Pd(II) and Au(III) in the 0.01 M MOTDA-1.0 M HCl solution system are 99.6% and 71.8%, respectively. In contrast, the other metal ions are hardly extracted under the studied conditions. The Au(III) and Pd(II) extracted in the organic phase are easily back-extracted with a 1.0 M thiourea/1.0 M HCl solution. A comparison with the conventional extractant for the Pd(II) separation, di-n-hexyl sulfide (DHS), revealed that the extraction rate of Pd(II) with MOTDA is much greater than that with DHS. The extraction percentage reached over 99% in less than a 2 min contact time. However, in the DHS-Pd(II) system, it takes about 240 min to achieve the extraction equilibrium. Furthermore, MOTDA can quantitatively extract Pd(II) up to half the molar amount of MOTDA. Therefore, MOTDA is a promising extractant for Pd(II) from the HCl solution after the removal of Au(III).

Jan 1, 2005

By F. F. Lins

There is a large use of mercury in Brazil by the gold miners in the so called "garimpos" (non registered mining operations), where it is usual to recover the gold contained in the gravity concentrates by amalgamation, which is highly deleterious to environment if not conducted properly. Unfortunately, this is a common practice there. After presenting in brief the modus operandi generally practiced in the garimpos and the environmental problems, this work reviews some of the research conducted in CETEM according to two approaches: (i) replace amalgamation by other processes and (ii) develop technology to treat mercury-contaminated soils and effluents. Conventional processes like froth flotation, to recover gold from gravity concentrates, and centrifuges were considered. Also as alternatives to amalgamation, innovative process like the recovery of gold by coal-oil agglomerates and a technology that is currently under development in our laboratory, called gold-paraffin process, are described in brief, some results presented and their potential use assessed. To reclaim sites already polluted a technology was developed to float mercury selectively from contaminated soils. The potential use of centrifuges to pre-concentrate the mercury is also discussed. The scope for applying the last techniques is to concentrate the pollutants in a small volume of mass which would be suitable for recycling or isolation from the environment. A prospective technology to treat contaminated soils, or mercury concentrates, is the immobilization of mercury by adding inorganics. Concerning the ionic mercury which may be present in effluents, precipitation of the ions and flotation of the precipitates are being studied.

Jan 1, 1994

By Ryan Walton

The Flash Converting Furnace at Kennecott Utah Copper converted over 465kmt of high-grade matte in 2002 but was restricted due to low matte production to 395kmt in 2003. This paper presents updated operational performance data and describes improvements implemented since the mid 2001 rebuild. Matte burner feed distribution, silica and arsenic impacts on settler lime-based slag operability, blister laundering, uptake/boiler accretion control, and dust sulfation will be discussed, as well as current development requirements dictated by operational imperatives and furnace modification plans.

Jan 1, 2005

The purpose of this study was to investigate the immobilization as a host for metallic pollutants (Cr, Cu, Pb, and Zn) by ettringite phase. Ettringite phase is produced through hydration reaction of calcium aluminate with gypsum. From the XRD patterns, it is known that the distance between spaces in 010 planes in ettringite crystal increase with an increase of ionic radius of heavy metal except Pb; no big difference is shown. For this reason, the d-value of 010 planes in ettringite crystal increased with the substitution of Cr, Cu and Zn having a big Al ironic radius. But in case of Pb, because the substitution occurred at calcium site, it does not influence to increase d-value of 010 planes.

Jan 1, 2006

By Christophe Thiébaut

Keywords: Pyrochemistry, Salts Treatment, Distillation The pyrochemical purification of metal generates spent salts. When this metal is an actinide such as plutonium, the slags cannot be discarded and are thus disposed in nuclear facility. In order to handle with these slags, the decision has been taken to reduce stored quantities. The development of a pyrochemical treatment is in progress in the CEA Valduc centre. The feed salt, typically composed of various Pu and Am species contained into monovalent or divalent chloride matrix, is first oxidized to convert the actinides into oxides. Then the chlorides are separated from the actinide oxides by vacuum distillation. Temperatures higher than 750°C for monochloride salts mixture NaCl/KCl and higher than 1100°C for divalent CaCl2 base salts, are required to produce an industrial flow of vaporization. Inactive qualification of the process for NaCl/KCl base salt has been carried out with lanthanide surrogates. Then, a pilot equipment, called distillator has been designed and built for production-scale distillation of NaCl/KCl and CaCl2 oxidized plutonium salts. Industrial flows of vaporization have been obtained with this pilot equipment : about 4 g/cm²/h for NaCl/KCl at 800?900°C and 1 Pa, and more than 1,5 g/cm²/h for CaCl2 base salts between 1000?1200°C at 0.1 Pa. The last step, now in progress, is the integration of the distillator into a glove box.

Jan 1, 2005

By Elli Nurminen

Keywords: Thermal conductivity of sulphates, flash smelting, heat recovery boiler, flue dust Accretions and build-ups in metallurgical heat recovery boilers decrease the efficiency of the heat transfer and may cause process shut downs. Transient plane source method (Hot Disk) has been applied to measure the thermal conductivities of the Copper Flash Smelting flue dusts. Thermal conductivities of copper, iron and zinc sulphates, and process flue dusts were measured. The results indicate that all the components are effective thermal insulators, having a thermal conductivity of less than 1 W/mK. Decreasing dust layer porosity has an increasing effect on thermal conductivity. Insulating layers on the boiler walls decrease greatly the heat transfer efficiency of the boiler. The gathered information will be used in CFD-modelling of the process, and in the process control.

Jan 1, 2005

By Anat Deepatana

Bioleaching of nickel laterite ores is the extraction technology based on the use of heterotrophic micro-organisms and their organic acid products to dissolve metals from oxide minerals. This study examined the chemical leaching kinetics of limonite and nontronite ores with metabolites including citric, lactic and malic acids. The leaching process was found to follow the chemically controlled model. The leaching kinetics was found to be significantly influenced by the acid strength or dissociation of acids in solution. Although increasing the acid strength increased the rates of leaching, this trend was not indefinite. An optimal acid concentration that defined the fastest leaching rates was identified for each acid. The amenabilities of the minerals hosting the nickel and cobalt in limonite and nontronite to organic acid leaching were also established.

Jan 1, 2006

By Pengfu Tan

Converter slag chemistry control has played an important role in optimizing converter operations. A thermodynamic model of copper P-S converter has been developed to predict the behavior of magnetite in the converter slag. Predictions of bath temperature, slag and matte compositions, and magnetite content in the slag have been validated by industrial data. The effects of fluxing strategy, returns and skim charges, oxygen enrichment, and temperature on the magnetite formation in the slag have been predicted and discussed. Some improvements of the industrial operations have been presented.

Jan 1, 2005

By Adriana Gómez

White dross is a result of the aluminum oxidation during its primary production and is mainly composed of metallic aluminum, Al2O3, with minor amounts of AlN and some other oxides. Because of the great variety of phases, the quantitative characterization is complicated. This work shows a quantitative method to determine the main phases of white aluminum drosses by means of X-ray diffraction (the Rietveld method). Nowadays the Rietveld method is maybe the most useful method for obtaining quantitative phases information in multicomponent mixtures, this method permits relatively quick quantitative phase analysis by fitting the calculated X-ray diffraction profile with the observed one. The analysis were done using powder with a grain size less than 45 µm; to obtain the suitable material size the aluminum dross was grounded by ten minutes, several times. The grounded material was screened, and the material smaller than 45 µm was taken to quantitative XRD analysis. Keywords: Rietveld Method, Characterization, Aluminum dross.

Jan 1, 2005

By Guihong Han, Duo Zhang, Yanfang Huang

Ni2SiO4 was prepared by chemical precipitation process as a novel anode material for lithium-ion batteries. The structure and morphology of further annealed Ni2SiO4 samples were characterized by XRD and SEM analysis. The electrochemical performance including cyclic voltammetric curves (CV), electrochemical impedance spectra (EIS), charge/discharge curves and cycling performances were also determined. The results demonstrated that the crystal structure of the samples is orthorhombic having space group Pmn21. The morphological structure of materials exhibited cubic particles with sizes in the range of 50–80 nm. The first cycle charge capacity of the pure Ni2SiO4 particles reached to 753 mAh g−1 with the coulombic efficiency of 63.8%. The charge capacity remained 305 mAh g−1 at a current density of 100 mA g−1 even after 50 cycles, which is nearly 208% higher than those of the Ni2SiO4 with SiO2 impurity. Ni2SiO4 can be a promising alternative anode material.

Mar 1, 2018

By Juliana Gutiérrez-Paredes

Keywords: Slag, chromium oxide, recovery, stainless steel Experimental and theoretical work was performed to estimate the effect of slag basicity and amount of reducing agents on the reduction of chromium oxide from the slag which interacted with molten steel at 1600°C. The slag system contained CaO, MgO, SiO2, CaF2 and Cr2O3 together with Fe-alloys (Fe-Si and Fe-Si-Mg). The CaF2 and MgO contents in the slags were 10 mass % each; Cr2O3 was 25%. The amount of the ferroalloys ranged from 12.5 to 50 g per 100 g of slag. The (CaO+MgO)/SiO2 ratio was held at 1 and 2. The Cr yield was determined using both Fe-alloys as reducing agents. Some estimations were made to determine the theoretical effect of temperature, slag basicity, (CaO+MgO)/SiO2, and amount of reducing agents in the slag on the chromium recovery. The FACT (Facility for the Analysis of Chemical Thermodynamics) computational package is used to determine the equilibrium between the slag and molten steel.

Jan 1, 2005

By Olga Karabelchtchikova

Keywords: Multipass grinding, Residual stress, Retained austenite, X-ray diffraction The study investigated residual stresses behaviors and their superposition effect in D2 dies for thread-rolling applications. A nested factorial experiment was applied to test hypotheses that the residual stresses profiles change due to combination of heat treatment and multipass grinding operations, and that certain patterns can be derived due to the memory relationship between pre-existing and final residual stresses distributions. The amount of the retained austenite along with residual stresses in variation with depth was measured using x-ray diffraction technique. Statistical analyses indicate that the proposed hypotheses hold. Residual stresses distributions as well as tensile peak location were found to be significantly influenced by the treatment parameters used. Unique characteristic patterns in the residual stresses profiles were observed due to multipass grinding technique across all experimental conditions. This finding suggested a plausible memory relationship between the cutting passes, and the causes of the foregoing results are further proposed and discussed.

Jan 1, 2005

By Nathan A. Tiner

Sulfuric acid anodizing process is extensively used in many industrial and consumer products to provide corrosion resistance to aluminum alloys. The anodic coatings produced consist of amorphous alhnum oxide with a pornus structure which is easily sealed and colored with dyes. The coatings may contain defects due to surface flaws, canposition and microstructure of the aluminum alloy, and/or due to the anodizing process conditions. This paper will describe the techniques used in anodizing process, various defects which may be produced in anodic coatings and the methods to control them.

Jan 1, 1992