Search Documents

By K. Lillkung, O. Forsen, J. Aromaa

"The dissolution rates of Pt, Pd and Rh in 250 g/L NaCl solution were calculated from the current densities determined by polarization curves and potentiostatic measurements measured with wire electrodes at atmospheric pressure. The results achieved with the two methods were similar. The dissolution rates at the corrosion potential were in the order of few nanometers per hour. The polarization curves indicated that to achieve dissolution rates required for economical operation on an industrial scale, the samples need to be polarized to higher potentials. When polarized to higher potentials, the metal dissolution rates were in the order of micrometers per hour. As the Tafel slopes of the metal dissolution region are fairly steep, the potential affects the dissolution rate greatly. Based on the activation energies, the dissolution reactions were controlled by a charge transfer step.IntroductionPlatinum group metals (PGM) have some very unique properties such as their inertness, giving excellent corrosion resistance, and a high melting point. At the same time, these factors make the refining of these metals very challenging. The main applications where PGMs are used are different catalytic converters, mostly in automotive catalysts. The used catalysts are also an attractive secondary source of PGMs. The exact concentrations of PGMs in catalysts vary widely depending on the manufacturer, the age and the capacity of the catalyst. The concentration of Pt in a new catalytic converter range from 300 to 1000 ìg/g, Pd from 200 to 800 ìg/g and Rh from 50 to 100 ìg/g [1]. Precious metal catalysts usually consist of a coat of the metal supported on ã- alumina. The recovery of metals from automotive catalysts has received much attention during the last few years [1-3]. In the near future, the use of PGMs in fuel cells is predicted to increase the amount of secondary PGMs available [4]."

Jan 1, 2012

By A. J. Paul

Traditionally, 16"/50 caliber projectile shells have been fabricated from forged steel. The Naval Surface Warfare Center (NAVSWC) has determined that cost savings of approximately 60% (-$4.7M/year) as well as improved shell fragmentation can be achieved by casting these shells from austempered ductile iron. One of the technical concerns arising out of this material substitution is the role of the casting process in controlling the quality of the cast shells. Optimizing the process through proper orientation of the mold, placement of chills, superheat, etc., can minimize shrinkage porosity and, consequently, flaw size. For this purpose, the mold filling and subsequent solidification of the projectiles was simulated using a 3-D, fully transient, coupled fluid flow and heat transfer model based on finite differences. Several casting orientations were investigated and the casting parameters were varied to optimize the process and minimize casting defects. A comprehensive software tool, which was developed using state-of- the-art visualization techniques, has been used to analyze the process of casting. Emphasis is placed on the use of this visualization tool as an aid to the foundry engineer for process optimization.

Jan 1, 1992

By R. S. Krarner

Fly ash, a by-product of coal burning power plants, poses a major problem for the utility industry since most fly ash must be landfilled. These quantities may represent as much as 20% of the total material going into landfills. A major problem with fly ash utilization is that although the ash consists of useable components, ash composition can vary depending on the types of coal burned and plant operating conditions. Ash is first characterized using SEM, image analysis, and chemical methods. Processing techniques were developed to separate ash into various components including cenospheres, magnetic spheres, carbon, and clean ash. These products are again evaluated for various utilizations before being used to produce valuable products such as mullite, activated carbon, fillers in plastics, and concrete.

Jan 1, 1994

By Xi Yun Yang

Ultrafine (0.1µm) spherical magnetite powder was prepared successfully by hydrothermal reaction of ferrous sulfate and sodium hydroxide with activated pyrite as reducing agent in the temperature range 120-140?. XRD and XPS analyses indicate that pH value and pyrite amount have a direct influence on the composition of the product. Stoichiometric Fe3O4 can be obtained only when pH value is 12 and the molar ratio of pyrite/ferrous sulfate is 1:1.8. The hysteresis loop of Fe3O4 shows a ferromagnetic behavior with a saturation magnetization of 75.2 emu/g and a coercivity of 152Oe.

Jan 1, 2006

By D. Zhao

High temperature deformation characteristics of austenitic 304L, and martensitic 410 and 416 stainless steels were investigated by conducting compression tests over a wide range of temperatures and strain rates (950-1250 C and 0.001-20 s-1). Flow behaviors of the three alloys were characterized. Optical metallography was performed to determine the as-deformed microstructures. The flow behaviors were related to microstructural phenomena during high temperature deformation. Dynamic recrystallization was responsible for the flow softening. Both dynamic and static recrystallization were operating, and the recrystallized grain size increased with increasing temperature and decreasing strain rate. Strain rate sensitivity was found to increased with increasing temperature and decreasing strain rate. No defects such as cracking and shear bands were observed at those test conditions. Preferred processing conditions can be selected by considering as-deformed microstructure and strain rate sensitivity.

Jan 1, 1994

By Enrique Posada

"The Valle de Aburrá area, corresponds to the city of Medellín and neighboring municipalities, with more than 3 million people. The area generates a sizable amount of solid waste, which has been taken to landfills for the last 20 years. This paper proposes a model for public policy making which considers the cost and benefit of different alternatives to handle the wastes in the coming 20 years. Combinations of several alternatives: Recycling, waste reduction, waste separation, incineration, land filling with lixiviate treating and gas energy recovery, and organic waste composting are considered and modeled and the results presented as a contribution for a more rational approach to policy making than the one currently being employed.IntroductionThe author, working for INDISA S.A., acted as a consultant for the direction of planning of the Empresas Varias de Medellín in 2004. This entity has the responsibility for the handling of the solid wastes of the city of Medellín and some of the neighboring municipalities. At the present time more the 700.000 annual tons of waste are taken to the site of La Pradera, located in very rainy location (3.000 mm of precipitation per year), with complex in topography and very far away from the sources of the waste. During the work the author detected important problems that should be addressed, as follows:Lack of adequate technical administration and resources. The entity did not count with sufficient human resources to focus on the appropriate technical handling of the solid waste. The organization worked mostly with independent contractors, lacking enough coherence and integration. The internal workload was too large for the few people who had technical responsibility and this gave rise to attention problems. It is important to have clear technical procedures, technical know how and human resources, continuity in the activities. It is important to have a clear capacity to plan, to study, to make tests and monitoring, to pursuit and develop ideas, to optimize the processes and to introduce changes, to respond to environmental authorities, to the communities and to mass media and to handle the contractors. All this was basically lacking. In the case of the handling of the sanitary filling of La Pradera, for example, although the people in charge were very able and dedicated, the magnitude of the task was too large and the resources they had were insufficient. As a result, the site had at the time of the study, problems with thousands of vultures, lack of immediate cover up for the waste, uncontrolled leaching, the area being dirty and little attractive, despite being called a park."

Jan 1, 2008

By Basak Anameric

Pig iron nugget process was developed by Kobe Steel as an environmentally friendlier, economical alternative to traditional blast furnace process. The process aimed to produce highly metallized, slag free pig iron nuggets throughout a single stage heat treatment, utilizing coal as a reducing ? carburizing agent. The objective of this work was to determine whether the pig iron nuggets produced at the laboratory conditions had comparable physical and chemical properties with the blast furnace pig iron. The physical and chemical properties of the pig iron nuggets were determined utilizing x-ray fluorescence spectroscopy, x-ray diffraction, optical microscopy, scanning electron microscopy, energy dispersive spectroscopy and apparent density measurements. The pig iron nuggets had similar chemical composition and apparent density values (6.7 ? 7 g/cm3) with blast furnace pig iron and they had microstructures similar to low carbon white cast iron. These properties make them a competitive alternative to blast furnace pig iron.

Jan 1, 2006

By M. Zamalloa

Slag foaming is an important phenomenon in many metallurgical processes. It creates large surface areas for multi-phase reactions to take place. In other applications, it protects electrodes and improves the energy efficiency by reducing radiation from hot surfaces. However, it may also be a source of serious disturbances. To control and optimize the use of slag foams, an extensive knowledge of the factors controlling the foam formation and stability is required. Slag foaming experiments were carried out using synthetic FeO-CaO-Si02 slags at temperatures ranging from 1200 to 1350 "C. A data acquisition system was used to continuously measure the foam height, gas flow rate, bubble frequency and temperature. The experimental results show that the gas injection rate has a strong effect on the behaviour of slag foams. At high flow rates and rapid bubbling, unstable foams with short decay times were created. The addition of P20, favours the foam formation and stability by lowering the surface tension of the slag. The average foam life increases with decreasing basicity (CaO/Si02). It is proposed that this is attributed to the increase of the surface viscosity due to surface adsorption of a thin film of silica, retarding the drainage of the liquid films.

Jan 1, 1992

By Renaud Metz

The DOPA process (Direct Oxidation of a Precursor Alloy) was used to prepare ceramic powders based on doped SnO2 and ZnO. The DOPA process consists essentially in the direct oxidation of a homogeneous precursor alloy. A unique advantage of this process is its rather benign environmental impact since no dangerous reactants are used and no harmful by-products are generated. Only oxygen and the alloy metals participate on the chemical reaction to produce the multi-component oxide. Homogeneous alloys of niobium, cobalt and chromium doped tin have been prepared. The molten metal alloy is atomised in air using a double fluid nozzle to produce metallic powders. A subsequent thermal treatment is carried out to fully oxidise the sprayed metal alloy powders. These raw powders are used to prepare a ceramic powder through a mill homogenisation and atomisation process. The ceramic powder is then uniaxially compacted in disc shape and sintered in an oxidising atmosphere. The resulting sintered bodies are metallised on their flat faces and the cylindrical surface is passivated using lead free glass enamel. These ceramics present excellent semiconducting properties with non-linear (non-ohmic) characteristics. The DOPA process is found to be an attractive procedure to obtain ceramic powders for the preparation of SnO2 varistors.

Jan 1, 2006

By John Sakala, Jeyapandian Sasikumar, Sydney Kwalela

The Isasmelt Furnace was commissioned in September 2006 with a concentrates treatment capacity of 850,000 tonnes per annum. However, the converter section became a bottleneck to the high throughput. Over 25% of the Isasmelt Furnace down time was attributed to lack of converter space. Factors that affected converter operations were low tuyere line campaign life (an average of 150 blows), high reverts generation, low conversion rates, and high converter cycle time. As a result of efforts carried out to improve converter operation, the average campaign life has increased to over 250 blows and reverts generation has been reduced from 22% of concentrate treated to 15%. Blister copper conversion rate has increased from 15 tonnes per hour to 19 tonnes per hour and blowing time per cycle has been reduced from 5.7 hours to 4.7 hours.

Jan 1, 2012

By D. M. Hausen

Microscopic point-counting of polished sections, in combination with x-ray diffraction analyses of representative whole rock samples, provides an efficient means to compare the modal mineralogic composition of different rock types. Major gangue minerals, e.g., quartz, feldspars, micas, amphiboles, chlorite, clays, etc., are estimated semiquantitatively by x-ray diffraction techniques, utilizing optimum grind, gridded sample surfaces and a sample spinner during scanning. Opaque to semi-opaque oxide and .sulfide phases are estimated by microscopic "point-count" and "gross-count" scanning. Total mineralogic compositions are calculated and normalized to 100 percent from XRD and microscopic data by computer programming. Comparative mineral analyses for different rock types, as well as quantitative microscopic data for various parameters, including particle and crystal sizes, textures, degree of alteration, paragenesis, etc., provide useful guides in mineral exploration, both in early stages of geologic mapping and later stages of economic evaluation. Several case histories are described.

Jan 1, 1981

By G. Nazari

ERAMET, through its subsidiary COMILOG, have rights to a rich niobium and rare earth deposit inGabon. The Mabounié deposit, is located 50 kmfromthe town of Lambaréné, in a fairly remote location. ERAMET has been developing a process to recover value metals for several years, and approached Hatch Ltd. to design a sizeable Demonstration Plant to help them further optimize the process, and prove the flowsheet is technically viable. The process employs concentration techniques to recover an upgraded Nb/REE feed material for processing in the subsequent leach step. Rare earths and niobium are selectively leached, and subsequently precipitated. Following precipitation, rare earths undergo bulk separation and are purified to produce LRE and mixed MRE/HRE products, which will be further processed by Third Parties. This paper provides a high-level overview of the process, summarizes the motivation for a Demonstration Plant in the vicinity of the deposit, and discusses technical challenges faced during the flowsheet definition and design phase. Key challenges are focused on and summaries of the methodologies used to address each challenge, as well as the solutions to overcome the challenges, are discussed. The paper provides motivation for further process simplification and concludes with a project update.

By Takayoshi Fujii, Mitsumasa Hoshi, Chikashi Suenaga, Yoshiaki Suzuki

"In a bid to renovate its Saganoseki Smelter & Refinery and to establish a leading production unit in terms of global competitiveness, Nippon Mining & Metals undertook major - restructuring efforts since 1993.One of its themes was the shift from a two-flash furnaces operation to a single-flash furnace operation. The shift was successfully completed in 1996 while maintaining the production at the same level (330,000 metric tons per year of copper) by adopting such measures as improvements in pneumatic concentrate dryers, the concentrate feeding system, concentrate burners, the furnace cooling system, and a new cryogenic oxygen plant was constructed.With a view to realizing high matte grade operation (at 65%Cu) and increasing the concentrate feeding rate, further steps were taken the capacity of waste heat boiler was expanded and technical improvements were added, including optimization of the smelting reaction in the furnace shaft. As a result, the smelting capacity, as of the year 2000, has increased to 450,000 metric tons per year of copper.IntroductionThe feed rate to the flash furnace was doubled to 140 t/h from 70 t/h in 1996. Teething problems, as a result of the renovation, were almost solved by the end of 1996, and the operation of the single furnace operation has become stable.The main theme was the shift from a two-flash furnaces operation to a single-furnace operation to maintain the production capacity at the same level, namely 330,000 metric tons of copper per year. Then, in a bid to further renovate the Saganoseki Smelter & Refinery and to establish a leading production unit in terms of global competitiveness, further enhancement of the flash furnace's productivity was planned.The purpose of this plan was to raise the copper production capacity to 450,000 mtpy building on the potentialities of existing plants and without installing new equipment."

Jan 1, 2000

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from theUniversity of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

By Malti Goel

"Ferrous and non-ferrous metals industries are source of both direct and indirect greenhouse gas (GHG) emissions. Metal industry accounted for 29.7% of the total GHG emitted from the Indian industry sector in 2007. Aluminum is second largest contributor after steel. Indian Aluminum industry has been growing and is adopting several effective measures for better efficiencies through process change and waste utilization. Improvement in the energy efficiency can form the basis of monitoring reduction in emissions. Under the National Action Plan on Climate Change 2008, National Mission for Enhanced Energy Efficiency (NMEEE) aims to upscale the efforts to unlock the market for energy efficiency improvement on a public private partnership (PPP) basis. For a transition to low carbon economy industry is undertaking voluntary measures through scientific and technological innovations both in upstream and downstream sectors. In this paper an attempt is made to overview recent developments in Indian Aluminum industry as well as summarize scientific & technological challenges and prospects.IntroductionAluminum plays a vital role in industrial development. It is a substitute for different type of materials ranging from wood to copper and steel. The aluminum industry has high energy consumption and high contribution to greenhouse gases from carbon dioxide and perfluorocarbons (PFCs) emissions. It is estimated that CO2 equivalent burden of aluminum industry is about 1% of total anthropogenic emissions. The anticipated world growth rate is 3.5% for aluminum demand. Through measures to reduce both direct and indirect CO2 emissions, electricity consumption was reduced from 25 kWh / kg of Aluminum in 1998 to 15 kWh / kg of Aluminum produced in 2008. It is targeted to further reduce it to 10.8 kWh. Aluminum industry is also responsible to about 60% of all PFC emissions. The PFC emissions are harmful to environment, accumulate in surrounding vegetation and contaminate. Efforts to reduce PFC emissions from aluminum industry started early and reduced to 0.5-1 kg / tonne in 1990 [1] from 12-15 kg / tonne in 1940. Since 1990s to 2000 it further reduced to 0.2 -0.4 kg / tonne as seen in Fig. 1. The Global Aluminum Sustainable Development Initiative (GADSI), targets perfluorocarbon (PFC) specific emissions reduction of 80% for 2010 relative to 1990."

Jan 1, 2011

By Rafael Padilla

The recovery of copper from chalcopyrite concentrates by leaching is difficult due to the slow dissolution kinetics of this mineral in most leaching media. However, recovery of copper from sulfidized chalcopyrite (a mixture of CuS and FeS2) by leaching is faster and could be selective depending on the leaching media. In this paper, the result of an investigation on the H2SO4-O2 pressure leaching of sulfidized chalcopyrite is presented. The variables considered in the study were stirring speed, concentration of sulfuric acid, temperature, and partial pressure of oxygen. The experimental data indicated that stirring speed over 500 rpm and sulfuric acid concentration over 0.1 M had very little effect on the leaching rate. An increase in temperature from 90 to 100 ºC increased both copper and iron dissolution; however, further increase to 120 ºC affected negatively the copper dissolution. Oxygen partial pressure was found to be the main variable that controls the copper/iron selectivity of the leaching. An increase in oxygen partial pressure increased significantly the rate of copper dissolution but deteriorated the copper/iron selectivity. The analysis for sulfur of the leaching solid residues indicated that most of the copper sulfide sulfur in the sulfidized concentrate oxidized to elemental sulfur.

Jan 1, 2006

By Evgueni Jak

Recent advances in analytical, experimental techniques, and computer-based theoretical modelling of fundamental properties and elemental processes, provide new opportunities to develop the next level of whole-of-reactor pyrometallurgical furnace models. These models have the potential to significantly improve the prediction of, and adding value to, industrial operations. In non-ferrous smelting, the starting point of these models is the development of multicomponent thermodynamic databases for gas-slag-matte-speiss-metal-solids phases supported by systematic experimental research. The whole-of-reactor-models additionally should take into account kinetic processes taking place at micro- and macro- scales, and other key factors. Examples of applications of the latest research tools and modelling approaches to analysis of industrial flash and top submerged lance (TSL) sulphide smelting processes are presented. Different levels of industrial modelling are discussed from elemental local reactions, through general and more detailed whole-of-reactor-models, to plant sections and further to whole plant operation models. Some principles for development of pyrometallurgical reactor models are discussed.

By Saskia Duyvesteyn

For many applications in hydrometallurgy and water treatment it would be advantageous to use ion-exchange resins in stirred reactors. However, attrition of the resin may lead to significant losses of both resin and metal values and prevent water quality goals from being reached. We have studied the recovery of fine resin particles by froth flotation, using the model copper - Dow XFS4195 chelating resin system. As the functional group on the resin is a bis-picolylamine, the resin should be amenable to flotation by anionic collectors, such as sodium dodecylsulfate and sodium dodecylsulfonate. The kinetics of copper loading from dilute aqueous solutions in an agitated vessel were studied as a function of copper concentration, pH and resin bead size. The flotation of unloaded resin was investigated for different types of collector, collector concentration, conditioning time, and resin bead size. Potential applications are discussed.

Jan 1, 1995

By Charles I. Richman

Aquispirillum magnetotacticum (AM) is gram-negative hetrotrophic bacteria that belongs to a class ,of magnetotactic bacteria that have an ecological niche in marine marches and fresh water swamp sediments. Thiobacillus Ferrooxidans (TF) is a Gram-negative, acidophillic chemoliths that may have similar chemical conditions within the cytoplasmic membrane as Aquaspirillum M. to support growth of Magnetosomes. Magnetosomes are cellular bodies that accumulate under slightly aerobic conditions. Magnetotactic motion occurs in an external magnetic field and depends on the medium viscosity. The Atomic Force Microscope equipped with a magnetic tip shows the presence of Magnetosomes in these bacteria strains. The size, shape of magnetosomes in AM and TF strains are characterized.

Jan 1, 1998

By S. W. Ip

Over the years, the importance of surface and interfacial phenomena has been neglected by the copper-nickel industry. As a result, little data on the surface and interfacial tension of the Ni matte and slag system are available in the literature. In view of the scarcity of information in this area, the surface tensions of the Ni-Fe-S system together with the Ni-Fe-S and fayalite type slag system were measured using the sessile drop technique. Drop images were obtained by X-ray radiography. For the Ni-Fe-S system, the results showed that the surface tension of the matte increases with matte grade. The surface tension behavior with changing matte grade showed a slight negative deviation from ideality. This indicated that FeS is slightly surface active in the nickel matte system. Results also indicated that small increase in sulphur content in the matte can decrease the surface tension quite significantly. The measured surface tension of the Ni-Cu-S system showed a linear relationship with the Cu2S content in the matte. The surface tension decreased with Cu2S content. Interfacial tension measurements showed a similar trend. That is, interfacial tension increased with increasing matte grade. The presence of MgO (-1.5%) and A12O3 (-6%) in the slag does not affect the interfacial tension value. Effects of matte surface tension on phenomena such as entrainment of matte in slag and infiltration of matte into refractory pores are discussed. The calculated flotation coefficients indicated that flotation of nickel mattes cannot be avoided by changing the matte grade. Filming of matte on bubbles can occur below a matte grade of about 19% Ni3S2. As for infiltration, refractory bricks containing high Cr2O3 will be easily wetted by matte regardless of matte grade. Therefore, bricks containing high Cr2O3 can easily be infiltrated by liquid matte.

Jan 1, 1993