Search Documents

By Fred Leighton

Outbursts, or the sudden and sometimes catastrophic expulsion of coal and gas into the working area of a coal mine, are a little understood and growing problem. The AE/MS (Acoustic Emission/Microseismic), or rock talk, activity prior to and associated with several outbursts has been recorded using ultrasonic and micro- seismic equipment and has been analyzed by the Bureau of Mines. Analysis of these data indicates that outbursts are comprised of several failures in rapid succession and that anomalous AE/MS data suitable for providing failure warning are generated 15 to 45 minutes prior to the failure. This paper discusses the techniques for recording and analyzing these data and presents sane case histories.

Jan 1, 1982

By Alan Campoli

Approximately 100 million fully grouted rebar roof bolts are installed each year in the United States, 80% are B-Series (5/8 inch fully grouted rebar in a one-inch borehole). The lesser used more expensive A-Series (3/4-inch fully grouted rebar in a one-inch borehole) maximizes resin performance. Standard B-Series provides only 60% of the pull out resistance of A-Series. The Eclipse System was developed by Minova USA Inc. and marketed with Excel Mining Systems to improve the performance of B-Series. A 1/8-inch offset bolt head combined with a specially formulated Eclipse Lokset resin cartridge results in increased mixing efficiency and more uniform resin anchorage. Over two million units have been sold to date; the majority of these Eclipse bolts have been sold to coal mines in the Illinois Basin. Pull testing has demonstrated that a Grade 60 Eclipse bolt provides equal or superior pullout resistance as compared to a Grade 40 No. 6 rebar. Short encapsulation pull tests have yet to consistently demonstrate the superior pullout strength of Eclipse to standard B-Series, however 12 inch Eclipse grouted columns have successfully held in excess of the bolt yield load. The successful substitution of Eclipse bolts for A-Series has significantly reduced the primary roof support costs by approximately $0.18 per foot of bolt. Recent over coring analysis of various anti-gloving methodologies performed in New Zealand has confirmed the superior mixing of the Eclipse system (5).

Jan 1, 2004

By Al Campoli

The majority of the 100 million roof bolts installed each year in the United States are 5/8 inch deformed rebar fully grouted into a one inch borehole. Commonly referred to as B-Series or No. 5 bar, this system is proven effective and cost efficient in coal mines with average to above average roof conditions. One of the critical variables affecting resin bolt performance is the size of the resin annulus, calculated as the difference between the hole and bolt diameters. The optimum annulus has been proven to be '/4 inch, which provides for effective mixing of the two polyester resin components and incorporation of the plastic film packaging within the cured resin. Glove fingering occurs when the plastic film is forced against the borehole wall potentially interfering with the mechanical interlock of the resin and the rock mass. Glove fingering is not a problem with the optimum '/n inch annulus but has been know to occur with the B-Series 3/8 inch annulus. Laboratory testing correlated the degree of Glove fingering with resin formulation and the bolt head to shaft axes alignment. Glove fingering occurred over 45 % of the grouted length of standard B¬Series bolts. The newly formulated Eclipse B-Series resin when combined with a 1/8 inch offset between the bolt head and shaft axes reduced the glove fingering 70%. The Eclipse system allows the 3/8 inch B-Series annulus to achieve the positive mixing characteristics associated with the / inch optimal annulus systems.

Jan 1, 2002

By Hamid Maleki

A new failure criteria is proposed for assessment of roof stability in underground sedimentary rocks. Unlike other stability assessment techniques, this method is simple and practical, having improved mine safety and productivity in several mines. It is shown that roof movements accelerate to a critical rate prior to actual roof collapse. Critical rates vary between 0.025 inches per day to 0.2 inches per minute depending on rock mass - pillar mechanical properties. Specific critical rates are determined for three rock mass - pillar categories which are common to mining in sedimentary rocks. Time-to-caving varies from one minute to ten days on rock structural controls and type of primary support utilized.

Jan 1, 1990

By Klaus Opolony

The world's most popular method of longwall mining requires multiple entry systems for the panels. In contrast to this mine layout the roadways in German coal mining are used for advanced mining from the rock mechanic point of view or are even re-used by a second panel. This procedure of roadway use is presented within this paper using a 3D visualisation software tool. In the previous conferences in Morgantown several papas had addressed the basics of rock mechanic background, planning tools and variants. This paper gives a practical case study for reuse of a roadway in a German coal mine. The heading and the use of various alternatives are compared under the aspect of efficiency and costs. Within the comparison the specific requirements and benchmarks of German coal mines are taken into consideration. The costs for a multiple entry system and first of all the development rates that can be achieved with common road heading systems are compared with international layout alternatives. A prospect includes a discussion of pro and con for various development methods. Devices are given due to this prospect if and how multiple entry systems are applicable to German coal mines. The paper gives an initial point for international comparison and is a base for further discussion.

Jan 1, 2003

By Stephen C. Tadolini, John Bolton, Bre-Anne Sainsbury, Tom Meikle

"The capacity of ground support components which have been affected by corrosion is reduced and may ultimately lead to dynamic failure of the component and the strata. In order to maintain an effective, long-term ground support system, significant campaigns of rehabilitation are often required in corrosion affected areas which also expose the workers to hazardous conditions. The most common corrosion protection for steel ground support utilises sacrificial systems such as galvanising. Galvanising has previously been proven to be susceptible to some corrosion processes. Stainless steel is the most effective in resistance to corrosion, but can be cost prohibitive, and its mechanical properties often make it unsuited to use in ground support components.Providing an outer protective plastic coating to bolts has proven to be an effective means of protecting the inner steel bar from corrosion. However, these support systems tend to be susceptible to coating damage, and require post cement grouting to provide full encapsulation. In comparison to a standard bolt/resin system, they can be slow to install and expensive. These systems have also been shown to reduce overall load transfer performance of the bolting system.In order provide a higher level of corrosion protection whilst maintaining current installation practices and bolting cycle times, Minova has developed the Enduro™ Steel Ground Support Range. The Enduro™ range consists of standard Minova steel ground support components which have been treated with a unique coating process. The Enduro™ coating has been tested in the harshest of conditions, in laboratory controlled conditions and in underground trials. It has been proven to effectively resist or completely eliminate the formation of corrosion, even in the most aggressive environments. This paper explains the process and provides the details of the laboratory and underground corrosion performance testing carried out on Enduro™ ground support products.INTRODUCTIONTraditionally, the most common form of corrosion protection in steel ground support consists of a sacrificial protective coating such as galvanising (Aziz, et al., 2013). Such coatings have proven to be ineffective in extreme high and low pH conditions with corrosion of the support system commonly encountered. There is also evidence that common forms of galvanising may actually increase the rate of corrosion in certain pH environments. Figure 1 shows typical corrosion and failure of a standard re-bar roof bolt."

Jan 1, 2016

By Li-min Liu

The Semi-Analytical method can be used to solve a variety of problems in geomechanics and civil engineering. When it comes to layered rock strata and rock masses, it is superior to all other analytical methods. This paper presents the application of a 3-D semi- analytical method to 3-D surface subsidence and stress analysis caused by mining. In this semi-analytical method the layered elements and triangular elements ate used alternatively. Their displacement pattern, strain mahix, elastic matrix, stiffiness matrix, load matrix and stress matrix are presented. A numerical simulation program based on the semi-analytical method bas been developed using Fortran 90. This program is suitable for subsidence prediction and stress analysis of mom and pillar mining, strip longwall and mechanized longwall mining methods. It is applicable to all geological conditions and mining methods. Comparing with the finite method, this method reduces significantly the number of simultaneous equations to be solved and the amount of data preparation. It not only reduces the computer memory, but also runs faster and cost less. Key Words Semi-analytical method, surface subsidence, stress analysis, layered element, triangular prism element

Jan 1, 2002

By Venkata S. Vutukuri

Compressive strength of cylindrical specimens of a model material and sandstone with various diameter/height (d/h) ratios was determined in unconfined compression tests. It was observed that the compressive strength increases with increase in d/h ratio. Triaxial compression tests were also conducted on the specimens of the same materials with a d/h ratio of about 0.47. It was observed that the axial stress at failure increases with increase in confining pressure. A very interesting correlation was found between the effect of d/h ratio on compressive strength in unconfined compression tests and the effect of confining pressure on axial stress at failure in triaxial tests. The relationships between d/h ratio and confining pressure, s3 in MPa are:- For model material - s3 = -0.95 + 1.7957*(d/h) 0.7883. For sandstone - s- (-0.4554 + 0.9888* (d/h) 1.0355. The correlation coefficients for these equations are 0.9997 and 1. These equations are valid for d/h ratios of up to 10.

Jan 1, 1993

By Sanjay Kumar Singh

This paper presents ground control technology associated with a continuous mining operation for mass exploitation of underground coal deposits in the Indian coal mining Industry It shows that competency of roof strata and performances of continuous miners are safer, than other coal mining method as well as productive and economical. Continuous miners keep playing a major role in the underground coal mining industry for their safety and as well as their productivity. Regarding past experiences in Indian coalfields, Chirimiri and Jhanjara mines have achieved exceptional performances, with a potential for over 500,000 tonnes per year. Tandsi mine has difficult roof conditions and does not typically achieve high production and productivity. Even so, the difficult roof conditions have been controlled with modern ?world best practice? roof bolting systems and an output of up to 1,200 tonnes per day has been achieved. It can further be emphasized that if this technology is implemented properly it will bring an unfathomable change to the Indian mining scenario. There are many mines in India that may have potential and economic viability with ground control technology concepts for installing continuous miner systems and beginning mass exploitation of underground coal deposits.

Jan 1, 2011

3-D finite element modeling was performed to study the effect of bedding plane sliding and separation and tensioned bolt in layered root It was found that the major influence zones of a tensioned bolt are restricted to the neighborhood of the anchor points; that bedding plane sliding and separation releases the vertical stress in the roof above entry but greatly increases the horizontal stress within the first layer of the roof, and that there is a triangular zone between the two adjacent bolts at and near the roofline level that is beyond the influence zone of the bolts which is liable to fail if conditions exist. Based on the results, three possible modes of roof failure are proposed for the design of tensioned bolting.

Jan 1, 2001

By Michael A. Berdine

In early 1997, Twentymile Coal Company took a dramatic departure from traditional longwall recovery methods. Previously, Twentymile's standard longwall meshing procedure included the use of chain link fencing material. Beginning with the 9-Right to 8-Right longwall recovery operation, Twentymile incorporated a polyester geogrid mesh system supplied by DYWIDAG-Systems International. This paper discusses the subsequent utilization of the polyester geogrid mesh system at Twentymile.

Jan 1, 2001

By Radoslaw L. Michalowski

The operation of mobile mining equipment near the crest of stockpiles and wastedumps often results in localized slope failures. The Bureau of Mines has developed a computer code based on a rigorous limit plasticity approach which determines the admissible total weight for a concentrated loading near the crest of these otherwise stable structures. The program is based on a three- dimensional analysis and provides an upper bound solution to the load that can be applied to the top of the operating distances for mobile equipment from the slope edge. This presentation will discuss the application of limit plasticity to the development of the local three-dimensional collapse mechanism, and the use of the computer code based on this approach for mining applications.

Jan 1, 1990

By Archie Richardson

Periodic weighting of longwall supports occurs during retreat ofthe face under certain geologic conditions. Strong stratain the immediate and main roof tend to cantilever over the gob, weighting the supports periodically. The distance between weighting peaks, as well as the intensity ofperiodic weighting, is determined by the suength and thickness of roof members, their location relative to the seam, the frequency of joinling, and characteristics of the gob. In this paper the effects of varying several of these variables ate investigated using block modeling. The models are calibrated against a published case history of periodic weighting in the Pittsburgh Seam. It is concluded that block modeling is a useful tool for correlating measured support pressure histories with expected modes of strata behavior in the roof, with potential for predicting shield behavior in new geologic enviromnents.

Jan 1, 1998

By Chao-jiong Hou

The necessity of using tensible rockbolt in the roadway with soft rock, high in-situ stresses, mining influence and other complex conditions was discussed, the structures of three kinds of tonsibte rockbolt and design principle were introduced in this paper. The tests of analogue material simulation under plane strain condition and underground industrial tests indicated that the effect of controlling deformation surrounding roadway by use of tensible rockbolt was good.

Jan 1, 1989

By Behdeen Oraee-Mirzamani

Since the advent of New Austrian Tunneling Method (NATM), shotcrete as a primary means of support in tunnels has been widely applied. It?s most important features are durability, speed of application and cost effectiveness. This paper introduces some tables that provide guidelines for the thickness of shotcrete required in some common situations of mine roadways. In order to devise such tables, two different arch sections, together with three different overburden types, were considered. Geotechnical parameters such as apparent cohesion and angle of internal friction of surrounding rocks were chosen, based on the five-category classification of Bieniawski. Two K0 factors (the ratio of horizontal stress to vertical stress) and an average rock density were utilized. Using numerical methods, 60 models were then devised in this way. By applying interaction diagrams of axial force and the bending moment for different thicknesses of shotcrete, appropriate shotcrete thickness for these models were calculated. The results of this research, as well as the methodology applied, can be used in mining roadway support design and all types of civil engineering tunnels.

Jan 1, 2011

The properties of coal or rock containing gas are very important both for studying coal and methane outburst mechanism and for controlling underground rock in mining. The theological fracture properties of coal containing gas were studied to obtain its rheological fracture principle both in microscopic scale and in macroscopic scale. The application of this principle is successful in explaining coal and methane outburst mechanism and for putting forward a rheological hypothesis of coal and methane outburst.

Jan 1, 1992

By G. Bucelluni

An essential element of truss bolt installation requires machines to angle a hole in the top of approximately 39° to 45° from its vertical axis. Parameter which inherently effect the drill position are: height, width of truss, physical size of mast, and whether single or dual mast bolting is utilized. The combination of these facets govern the installation procedures required for the bolting cycle. The following illustration with written explanation will demonstrate this concept. See Figure #1. [ ] This model assumes certain fixed criteria which corresponds to a dual mast drill design and a set 41° drill angle. Using the derived formula, the maximum possible seam height for both masts to touch the bottom can be calculated for any given condition by substituting by the appropriate bolt spread distance. [ ] In a high seam application where the mast touching the bottom was considered a requirement, the proposed model demonstrates the advantage of single mast drilling. See Figure #2. [ ]

Jan 1, 1982

By Gregory Hinshaw

Underground mine bolting machines have evolved since inception in the 1940's due to the need for increased safety and productivity. However, major design innovations historically came from changes in the mining plan and the mine environment. During the last ten years, productivity needs have outpaced the evolution of existing designs. J. H. Fletcher & Co. has responded with a commitment to research and development which has fostered several new designs. The most recent machine built is a walk through crawler frame powering four drilling units simultaneously with semiautomatic computer control using two operators. This machine utilizes technology to create a safer yet more productive roofbolter for continuous mining sections utilizing place changing methods.

Jan 1, 1998

By Kourosh Shahriar, Kazem Oraee, Ezzeddin Bakhtavar

"In this paper, a relationship between dependant parameters and the crown pillar thickness is first introduced. This relationship defines geotechnical problems caused by thin pillars and economic considerations created by pillars that are thicker than the optimum size. For this purpose, a dimensional analysis as an effective physico-mathematical tool was used. This technique restructures the original dimensional variables of a problem into a set of dimensionless products using the constraints imposed upon them by their dimensions. A model is hence introduced that calculates the optimum pillar thickness. The relationship introduced here and the method applied can be used by mining engineers in all situations where a combined open-pit and block caving method is deemed to be the most appropriate mining method.INTRODUCTIONMany deposits can be mined entirely with the open-pit method; others must be worked underground from the very beginning. In addition, there are the near-surface deposits with considerable vertical extent. Although they are initially exploited by the open pit method, there is often a ""transition depth"" where decision has to be made about changing to underground methods.Some of the biggest open-pit mines worldwide will reach their final pit limits in the next 10 to 15 years. Furthermore, there are many mines planning to change from open-pit to underground mining due to increasing extraction depths and environmental requirements. In this way, it is likely that block and/or panel caving will enable the operations to continue achieving a high production rate at low costs as an underground method (Bakhtavar et al., 2009).In these cases, it is often necessary to consider a crown pillar beneath the transition depth (open-pit floor) before starting an underground caving stope method (Figure 1).There are generally two kinds of crown pillar: a ""surface crown pillar"" and ""crown pillar between open-pit and underground mining."" In general, they both play the similar role in mining. Since the primary purpose of a surface crown pillar is to protect surface land users, the mine, and those working in it from inflows of water, soil, and rock; it is vital that the surface crown pillars remain stable throughout their life. When a crown pillar could potentially remain between open-pit and underground mining it is specially proposed to prevent water entering from the open-pit floor into the stope, as well as to reduce open-pit wall and floor caving."

Jan 1, 2010

By M. Zaki Rashad

In this paper, if three slant distances are measured from three given points of known coordinates to an unknown point, the position of this point (X, Y, and Z coordinates) can be determined. A computer program was designed for observing the movement of a point in the roof in Abu-Tartour mine (western desert, Egypt) to measure the convergence. This method, for general using, is very fast and can be applied without any restrictions.

Jan 1, 1990