Search Documents

By R. A. Halatchev

Historically two basic approaches of production sequencing have been formed in the theory of open pit mine design. The first approach implements a technological discretization of the pit space within the ultimate pit outlines where the minimum working width is the limiting technological factor. The second approach uses a pseudo-economic discretization based on the implementation of analytical methods for designing intermediate/ultimate pit outlines and the concept of pit shells generation. The paper offers an elaborate analysis of both approaches used currently for discretization of the geological medium into working benches and modelling the working zone of open pit mine. The analysis is extended with a new vision for unification of the mining systems in open pit mine design under the form of a classification. A comparison of the approaches is provided to illustrate their advantages and disadvantages with regard to the implementation of the principle of waste deferment as one of the main principles of mine planning that exploits the time effect of money.

Jan 1, 2003

By H. J. Bogert

Shallow, gently dipping quartz veins at the Mineral Hill Mine are mined in room and pillar stopes. Ore zones are severely folded and fractured, thus actual pillar strength and physical properties of the rock mass deviate significantly from conventional laboratory tests and pillar theory. Laboratory specimens large enough to include pre-existing fractures proved to be representative of actual pillar strength. Further adjustment for specific pillars was based on RQD. Deformation and stress were measured in several pillars during pillar recovery. Stress data and finite element modeling were used to estimate absolute pillar stress at failure. The stress/strain relation provided an excellent indicator of pillar behavior. Good agreement between lab data and underground data was found.

Jan 1, 1995

By Bruce F. Bohor

Silica sand has been mined in Illinois from the St. Peter Sandstone since the turn of the century, especially in the area around Ottawa on the Illinois River in the north-central part of the state. Production of this sand, consumed mainly by the glass and foundry industries but also sought after for many other uses, has grown with the economy, and last year's output in Illinois exceeded 4,000,000 tons. Such an important commodity was given the early attention of the Illinois State Geological Survey, and a very complete report was issued in 1928, authored by J. E. Lamar. The mining and processing of the sand has changed very little during the intervening 40 years, so that much of Lamar's data and descriptions are applicable today. More recently, the stratigraphy of the St. Peter Sandstone in north-central Illinois has become better known from the work of Willman and Payne (1942). The present authors have borrowed generously from Lamar's publication, and we wish to acknowledge the contribution of both of these studies to our work.

Jan 1, 1969

By M. J. Virnig, Christopher A. Fleming

THE CIP PROCESS "IN THE RIGHT PLACE AT THE RIGHT TIME? After its tentative introduction to the precious metals mining industry in the earlier part of this century, the carbon in pulp (CIP) process has now come of age, and is the process of choice on all new gold mills. Well over 50 percent of all gold that is mined each year is recovered by adsorption on activated carbon, and the percentage will increase in the years ahead, when old mills using Merrill Crowe technology come to the end of their lives, and as the proportion of world gold production from low-grade resources increases. The pioneering process development work in this field, which was mainly concerned with carbon elution, was carried out by Zadra and his colleagues at the United States Bureau of Mines in the early 1950's (Zadra et al., 1950, 1952), and led to the commissioning of the first large-scale, industrial CIP plant, at the Homestake Mine in South Dakota, in 1973 (Hall et al., 1974). From there, the process spread rapidly, firstly in South Africa in the late 1970's. and then throughout the rest of the gold producing world in the 1980's. There were several factors that led to the meteoric (by gold industry standards) acceptance and successful implementation of this new technology into gold processing operations worldwide. Firstly, and perhaps most fortuitously, the development of the technology closely paralleled the 1968 release of the gold price from the rigid constraints of the $35/oz. gold standard. With the value of the metal allowed, for the first time in modern history, to fluctuate in response to free market supply and demand forces, the gold industry witnessed an unprecedented boom as the price of their commodity increased ten-fold in a remarkably short period of time. This had several important spin-offs as far as new process developments were concerned: The profits realized by established gold-mining companies increased enormously and, consequently, there was more to spend on research and development and exploration for new deposits.

Jan 1, 1993

By Scott Brien, O&apos

Cyclones have become standard unit operations in mineral processing for both dewatering mineral slurries and for making separations at given particle sizes. Conventional cyclones are normally able to make moderately sharp cuts. However, the limited ability to control water flow out of the apex means that cyclones have difficulty handling fluctuations in feed. Underflow-regulated cyclones are cyclones with a rubber boot attached to the underflow. This boot acts as a non-return valve and restricts flow out of the apex of a cyclone. Normally, this type of restriction on a cyclone causes severe difficulties in cyclone operation. However, by adding a siphon arm to the overflow, water flow can be controlled. The siphon arm creates a vacuum that reduces or eliminates the air core, permitting better control of the ratio of water flow out of the overflow and underflow. A Linatex-developed underflow-regulated cyclone was compared to a conventional cyclone for its ability to dewater a sand slurry. The underflow-regulated cyclone produced slurries with solids contents as high as 80% in the underflow. Conventional cyclones produced lower solids content in the underflow under similar conditions.

Jan 1, 1997

By J. Pereyra, M. DeMarco

"INTRODUCTION It can be vital that bolted joints holding subassemblies together remain secure. Bolts should resist the loosening effects of vibrations and dynamic loads yet need to be easily removable during maintenance. When a threaded fastener is subjected to vibration, the rapid movement causes a lowering of friction against the threads and a subsequent loss of preload. The loss of preload allows the fastener to vibrate loose and possibly fall out. As the diameter of fasteners increase desired preload becomes increasingly more difficult to achieve. Input torque requirements for achieving proper bolt preload is exponentially related to any given fasteners diameter. This means that specialized tooling or bolting practices are usually required to attempt the tightening of fasteners to reach their required preload. Traditional methods can cause problems with joint integrity and do not provide consistent bolt load across the bolted surface. BOLTED CONNECTIONS A failed critical bolted joint can lead to high maintenance costs, machine downtime, and risk to worker safety. Control of the clamp load in a bolted joint is vital. However, when faced with a problem joint, it is not surprising that the design engineer will not have an answer if asked about the clamp load. Torque calculations must always be based on the existing conditions that often are vague. Unless all parameters are correct, the calculation will be unreliable. Examples of parameters are: • Thread condition of the fasteners • Hardness of contact surface • Material (steel, aluminium, copper, etc.) • Extra friction from a locking fastener • Extra friction from an adhesive • Lubricant on the thread • Type of bolt head (flanged, regular or serrated) • Surface coating of the bolt • New or reused fastener During tightening, bolts are subjected to both tensile and torsional stress. The total stress in a bolt can be calculated using the formula: Total stress = vsx2 + 3txy2 In order to maximize the desired tensile stress (sx) it is vital to minimize the torsional stress (txy). Tensile stress (clamp load) is achieved when the bolt is axially elongated. Unwanted torsional stress (twisting) in bolts arises during tightening due to thread friction. High thread friction increases torsional stress and causes yielding at lower clamp load levels than normal. A lubricant is necessary to minimize the malign torsional stress. However, many commonly used bolt-locking systems are based on increased thread friction (deformed nuts, adhesives, etc). To minimize thread friction and concurrently safely secure the joint has often incorrectly been considered impossible. The use of locking systems that increase thread friction is the single most common reason why the full capacity of bolted joints is not utilized. The following example illustrates the problem."

Jan 1, 2015

By A. L. Ling, A. K. Janzen

"Design of effective mine water treatment plants depends on the ability to reliably predict treatment outcomes, but systems with multiple chemical and physical treatment processes and recycle loops can be difficult to model. GoldPHREEQC is a modeling framework that integrates mass and flow routing capabilities of GoldSim software and water quality calculations provided by PHREEQC, and is well-suited to modeling parameters of interest in the mining industry, especially metals and sulfate. Physical processes such as membrane separation and greensand filtration are modeled by defining mass rejections for each parameter and flow routing based on vendor projections and bench- or pilot-scale equipment testing. GoldPHREEQC models chemical precipitation processes such as HDS metals removal and gypsum precipitation by (1) performing surface-aging and solubility calculations in PHREEQC and (2) using the GoldSim framework to direct supernatant and precipitate to subsequent process steps. Users can apply this modeling framework to predict effluent water quality, chemical requirements, sludge production, and required equipment capacity to support design, troubleshooting, and cost estimating. INTRODUCTION Design of effective mine water treatment plants depends on the ability to reliably predict treatment outcomes, but systems with multiple chemical and physical treatment processes and recycle loops can be difficult to model. GoldPHREEQC is a modeling framework that integrates mass and flow routing capabilities of GoldSim software (1) and water quality calculations provided by PHREEQC (2), and is well-suited to modeling treatment of parameters of interest in the mining industry, especially metals and sulfate. GoldPHREEQC can also be applied to other water treatment scenarios using inorganic reactions and processes. The GoldPHREEQC model framework moves water and mass between specified model nodes and calculates specified reaction and water quality outcomes. It can be organized to provide flow, load, and concentration information for each location, including effluent and byproduct streams, and outputs can be adapted to include power and chemical costs."

Jan 1, 2018

By R. S. Farinato

Thionocarbamate flotation reagents have enjoyed a niche position in the recovery of copper sulfides and activated sphalerites since their introduction in the mid 1950's (Harris, 1954). Thionocarbamates containing an allyl group (-CH2- CH=CH2), introduced recently Lewellyn, 1985; Nagaraj, 1988; Avotins, 1991), are used commercially as collectors for copper sulfides and activated sphalerite. Laboratory flotation tests and plant usage have demonstrated that allyl-containing thionocarbamate collectors exhibit certain unique properties that distinguish them from the corresponding dialkyl thionocarbamates. Spectroscopic (FTIR, XPS) and wettability studies of N-allyl iso-butyl thionocarbamate (AIBTC) and its saturated analog N-propyl iso-butyl thionocarbamate (NPIBTC) adsorbed on copper at pH 9 were performed in order to investigate whether there were any fundamental reasons for these differences. Flotation tests were carried out on chalcocite, copper ore and an activated sphalerite.

Jan 1, 1993

By David Field, David Powell, Richard Hulsen

The Mission Valley Light Rail will loop through San Diego State University (SDSU)and to minimize the impact of construction most of the works will be underground. The project will require construction of a 330-m long (1080-ft), 11.24-m wide (36.9-ft),single twin track tunnel through Stadium Conglomerate, a poorly cemented dense sandy gravel with cobbles. Key technical issues are discussed including the ground conditions and predicted ground response, the use of sequential excavation methods to control deformations and specific construction concerns such as instrumentation and monitoring. Management of the construction process to minimize risk is particularly important in this environment and the strategy selected to control the works is also considered.

Jan 1, 2001

By Peter Zhang

The immediate roof at the test site consisted of laminated clay shale that is likely to be susceptible to weathering. With seasonal dry-wet cycles in the mine ventilation air, the roof in the intake air would deteriorate and lose integrity over time. In many instances, the weathering-prone roof would gradually scale off piece by piece between bolts and over the entry corners. In some long-term entries, roof weathering could develop up to 2-3 ft deep with columns of bolted roof hanging under the upper intact roof. If wire mesh is used, the roof bags down and reduces the entry height, and the weight of the bagged roof tends to pull the bolts out and poses a safety hazard. An effective measure is always sought to support this type of weak roof that is sensitive to moisture degradation. One solution is to seal the roof shortly after entry development to prevent moisture penetration so that roof integrity can be maintained for the long term. In this application, a polymer-based sealing material was tested in the Rockspring mine for weathering protection and reinforcement. The material is a one-component polymer powder for spray application onto the roof and rib. The sealant material is mixed with water in the spraying nozzle to apply to the roof and rib as a paste. The product sets within 5-10 minutes and forms a membrane as thin as about 1/8-in. The membrane will quickly develop tensile and bonding strength within minutes and completely cure within a few days. Through sealing, bonding and lateral reinforcement, the integrity of the weak roof can be maintained. The material has been tried in a long-term evaluation over several months in a set of main entries in the Rockspring mine owned and operated by Rockspring Development, Inc., affiliate of Foundation Coal. Preliminary evaluation has shown that the material is an effective and economical solution to ensuring the long-term stability of weathering-prone roof.

Jan 1, 2009

By A. E. Reisenauer, R. W. Nelson, G. W. Gee

A model assessment was made to evaluate contaminant transport to ground water from clay-lined and unlined tailings pits. The input hydrologic soil characteristics were measured on materials typical of those found at the Morton Ranch uranium mill site in central Wyoming. The assessment involved combined saturated and partially saturated flow and contaminant transport models for two-dimensional cross-sections typical of the proposed Morton Ranch burial pits. Specifically obtained from the models were contaminant flow paths, the advancing contaminant flow fronts for sorbed and non-sorbed constituents, and travel times of contaminants along flow paths. Such results enable evaluation of the environmental consequences for the alternative control methods.

Jan 1, 1980

By Chester A. Rowland, David M. Kjos

INTRODUCTION Mineral ore comminution is generally a feed preparation step for subsequent processing stages. Grinding, the fine product phase of comminution, requires a large capital investment and frequently is the area of maximum usage of power and wear resistant materials. Grinding is most frequently done in rotating drums utilizing loose grinding media, lifted by the rotation of the drum, to break the ores in various combinations of impact, attrition and abrasion to produce the specified product. Grinding media can be the ore itself (autogenous grinding - primary and secondary), natural or manufactured nonmetallic media (pebble milling) or manufactured metallic media - steel rods, steel or iron balls, or a combination of autogenous media and steel balls (SAG milling). This chapter covers rod and ball mills utilizing manufactured metallic grinding media. MILL DESIGN The interior surface of rod and ball mills exposed to pulp and/or grinding media are protected from wear and corrosion by rubber, metallic or a combination of rubber and metallic wear resistant materials. Rod and ball mills essentially draw constant power, thus are well suited for use of synchronous motors with power factor correction capabilities as drive motors. A net of approximately 120 to 130 percent of running torque is required to cascade the charge in these mills. The pull-in torque is about 130 to 140 percent with the pullout torque to keep the motor in-step (in-phase) generally in excess of 150 percent. When rod and ball mill are started across-the-line the starting and pull-in torques result in inrush currents exceeding 600 percent which possibly result in high voltage drops. To deliver 130 percent starting torque to the mill the motor design must take into account the maximum anticipated voltage drop. Motor torque decreases as the decimal fraction of the voltage available squared. E.g., a motor rated 160% starting torque with a 10% system voltage drop will deliver 160% x or 129.6% torque to its output shaft When it is not possible or practical to start a fully loaded synchronous motor across-the-line it is possible to utilize the motor's pull- out torque to start the mill. By using a clutch, normally an air clutch. between the motor and the mill, the motor is brought up to synchronous speed before the clutch is energized. If the motor has an adequate amount (175 or greater) of pull-out torque the pull-out torque starts the mill without major disruptions on the electrical system. Since the energy release at initial cascade of the mill charge is an inverse function of acceleration time, a minimum acceleration time of 6 to 10 seconds or more is recommended to prevent damage to the mill or the mill foundation. Economics at the time of plant design and mill purchase determine the drive to be used. The simpliest drive is the low speed synchronous motor with speeds in the range of 150 to 250 RPM connected to the mill pinionshaft by either an air clutch or flexible coupling. Using a speed reducer between the motor and pinionshaft permits using motors having speeds in the range of 600 to 1000 RPM. In this speed range, if power factor correction is not required induction motors can be used; squirrel cage where there is no restriction on inrush current; slip ring where a slow start and low inrush current is required. Air clutches can also be used to ease starting problems with squirrel cage motors. In some areas of the world induction motors and starters are less expensive than synchronous motors at a sacrifice of motor efficiency and power factor correction. Dual drives, that is two pinions driving one gear mounted on the mill, become economical for ball mills drawing more than 3500 to 4000 horsepower (2600 to 3000 kilowatts). Further developments of the low frequency, low speed synchronous motors with the rotor mounted on the mill shell or an extension of one of the mill trunnions could improve the cost picture for these "gearless drives", making them practical for large ball mills. The percent of critical speed, which is the speed at which the centrifugal force is sufficiently large to cause a small particle to ad- here to the shell liners for the full revolution of the mill is given in mill specifications. Critical speed is determined from the following: Where D is mill diameter inside liners (specified in meters). Cs is critical speed in RPM. When D is specified in feet

Jan 1, 1998

By R. P. King

A new device, called the dual impact load cell, has been developed and built at the Comminution Center to measure fracture energy and damage accumulation in brittle particles that are subject to impact. The results show that damage accumulation during impact is not a significant factor in determining the fracture energy or the particle strength. However, predamage induced by thermal pretreatment of the particles has a significant effect on both fracture energy and particle strength.

Jan 1, 1995

By D. A. Norrgran, J. N. Orlich

Described is the application of high- intensity magnetic separation throughout the spectrum of industrial minerals. Performed either wet or dry, the separation has application in both the recovery and concentration of value minerals and in removing deleterious mineral constituents. The various types of magnetic separators along with the design and operating parameters relative to separation response are characterized. The characteristics of specific minerals to magnetic collection and the production of high-grade concentrates are described. Laboratory, pilot-scale, and plant studies carried out on a variety of industrial minerals have demonstrated the effectiveness of magnetic separation as either a primary or a secondary unit operation to achieve product quality.

Jan 1, 1987

By C. J. Hall

An investigation of multi-shaft airflow problems by the author in 1976 (1) was presented in the hope of arousing considerable written comment, but in fact-. only one contribution (2) was forthcoming. The investigation in this paper is taken several stages fur¬ther, because the matter is of major importance in many American hard rock mines with complex networks extending over thousands of meters vertically. The examples used have all been generated thermodynamical¬ly and checked by motive column (denisty) calculations. Dry air has been used to reduce the amount of time spent on the rather complex calculations, but it has been shown (3) that the principals developed apply equally well to air/vapor/water mixtures. Initially the subject is investigated using both thermodynamic and motive column analyses. The latter part of the paper concentrates on a motive column presentation. Both methods are, of course, equally valid and give identical answers to any situation when correctly applied, as is shown in the worked examples.

Jan 1, 1980

By Daniel Su

This paper describes recent ground control challenges encountered at the longwall recovery areas of one of Bailey Mine?s two longwall faces and the proactive measures taken by CONSOL management and engineering to mitigate them. The challenges derived primarily from the following causes: (1) irregular roof coal and draw slate thickness, (2) presence of thick sandstone at the recovery area and extremely weak rocks below the sandstone, (3) close proximity to a regional anticline, (4) low shield set pressure and tip load, and (5) ineffective primary roof support that led to progressive failure of the headgate roof. The presence of the anticline contributed to extensive fracturing of the sandstone. Excessive pot-out in advance of the shields frequently occurred near mid-face due to the presence of thick draw slate and irregular roof coal near the recovery area. This, in turn, resulted in face heights that exceeded the maximum reach of the shields. Subsequently, during longwall meshing, when the advance rate slowed considerably, fractured sandstone would often break loose, causing the shields to yield, thereby reducing the height and inhibiting shearer movement. To improve the headgate and face conditions within the longwall recovery area, several actions were taken, including: (1) assessing site-specific roof geology by conducting in-mine roof coring around the recovery areas and by mapping immediate draw slate and roof coal thicknesses within surrounding entries, (2) increasing pump pressure and thus shield set pressures (3) diligently monitoring shield set pressures and longwall extraction horizon, (4) installing additional cable bolts and roof screening to prevent progressive failure of the immediate headgate roof, (5) fully-grouting supplemental cable bolts to improve headgate support stiffness, and (6) gluing the headgate roof within the recovery areas with polyurethane. As a result of these collective efforts, longwall recovery delays at Bailey Mine were reduced from 21 days in 2006 to nearly zero in 2009.

Jan 1, 2009

By Gus H. Goudarzi

The apatite deposits in east-central Bahia, Brazil, are about 50 km east of Serra do Jacobina, between lat. 11° and 12° S. and long. 39°40' and 40° W. Apatite was found and examined at 15 localities in a mineralized belt that strikes about N.25° - 30 W. over a distance of about 100 km, but the size of the deposits has not yet been determined. Rocks of the region consist of a sequence of Precambrian migmatites and quartz feldspar paragneisses containing units of pyroxene-rich rocks, lenses of sillimanite-bearing quartzite, amphibolite zones, and calc-silicate marble lenses. Pegmatites and granites of probable anatectic origin (anatexite) are abundant. Faults are numerous. Clastic sediments of Tertiary and Quaternary ages cover most of the area; thus, outcrops of the Precambrian rocks are sparse. Trenches and pits have exposed mineralized zones as much as 10 m wide at some localities within the region. A layer of apatite at least 1 ½ m thick is exposed in a trench at Lagoa do Mel. At Rio do Peixe, vertical shafts have penetrated a mineralized zone, to a depth of as much as 13 m, of which about 25 percent is apatite. Apatite is massive or forms minute crystals, stringers, and disseminated grains in alkalic host rocks. At Apolinario, euhedral crystals of apatite are as much as 50 cm long and 30 cm in diameter. Associated minerals include vermiculite, biotite, scapolite, opal, chalcedony, epidote, montmorillonite, chlorite, kaolinite, sericite, magnetite, and limonite. Apatite is everywhere intimately associated with pyroxene-rich rocks, alkalic syenite pegmatites, and alkalic granite pegmatites. At Panelas-Retiro, apatite is associated with pegmatites, crystalline calcite (vein calcite), vermiculite, and pyroxene-bearing rocks. Analyses of samples show that the apatite is radioactive and rare-earth-bearing. Traces of vanadium and titanium were detected by spectroscopic analysis. The apatite was probably derived from phosphatic zones in the original Precambrian sedimentary rocks and has been crystallized and some mobilized by high-temperature regional metamorphism (higher amphibolite facies) into veins, pegmatites, and along certain preferred beds and fractures. Radiometric and geophysical surveys, in addition to conventional geological investigations, are planned to further investigate the nature and economic potential of the deposits.

Jan 1, 1972

By S. C. Schmelter

The destabilizing effect of water pressure on rock mass stability is examined quantitatively by the finite element method. A coupled code that accounts for the simultaneous effects of rock mass deformation and transient fluid flow is used for this purpose. The traditional soil mechanics assumption of an incompressible fluid is shown to be untenable for the analysis of porous, fractured rock slopes. A Mandel-Cryer effect, a transitory but elevated and potentially destabilizing water pressure following a cut, was not observed.

Jan 1, 1997

By R. A. Jankowski

Although the number of operating longwall mining systems has remained relatively constant, longwall production levels during the last five years have increased significantly. In the United States, longwall mining now accounts for approximately 50% of all underground coal production. While longwalls are highly productive and offer other advantages, operations employing this method of mining continue to experience dust-compliance problems. This increased longwall productivity has meant that far more dust is being produced. An improved understanding of the longwall face-ventilation system and the advancement of face-ventilation technologies are necessary to ensure all face personnel are allowed to work in an environment that is free of excessive levels of airborne respirable coal mine dust. The Dust and Toxic Substances Control Branch, National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, examined several basic principles of the long wall face-ventilation system and has evaluated the effectiveness of numerous improved face-ventilation techniques for longwall mining systems. These include identifying improved techniques for measuring face-ventilation parameters on longwall mining sections and investigating the fundamental relationship between face airflow and the entrainment and dilution of respirable coal mine dust. Studies have been completed to determine the impact on face dust levels of using belt entry air to ventilate the longwall. Novel methods have been identified to increase the face air¬flow and to manage face airflow to effectively minimize dust exposure to face workers. Unique systems of auxiliary face ventilation have been developed and evaluated at full-scale, simulated longwall test facilities. The theoretical and applied aspects of each of these principles and technologies are discussed. Application of these results throughout the longwall mining industry, as documented from surveys conducted in the early 1980s and 1990s, have reduced the health hazard associated with excessive exposure to respirable coal mine dust.

Jan 1, 2000

By Brian H. Jasperse, Nicholson Peter J.

Gravity retaining walls have been constructed using Deep and Shallow Soil Mixing (DSM and SSM) since 1991 in the United States. These walls, for both temporary and permanent uses, were constructed by mixing cement with in-situ soils over a volume containing 100% of the required gravity wall zone. Modern design techniques have reduced costs substantially by forming the required gravity wall section as a composite mass. Using ratios of 15-35% by volume, treatment f the ground forming the required gravity section has reduced the cost from about $40 to about $20 per square foot. Design, construction and actual performance of these gravity walls are presented.

Jan 1, 1999