Search Documents

By Bruce Hern

The last 10 years have seen a dramatic increase in the requirements for product coal quality control. This has led to electric utility sulfur scrubbing, metallurgical blast furnace optimization and coal producer blend and yield optimization. To achieve this improved level of control, coal producers are designing facilities that emphasize new technology. New facilities will be designed and existing facilities will be retrofitted with state-of-the-art technology to meet quality control standards that are dictated by the market. The first step in designing for process control requires the identification of those parameters to be controlled and the upsets that can cause variances in the final shipped product quality. The most common parameters that require control are the surface moisture (%), ash (%), pyritic sulfur (%) and gross calorific value (Btu). Total moisture is that moisture that exists on the surface of the particle and is inherent in the particle itself. For the purposes of control, the total moisture is monitored, while surface moisture is controlled. Ash is the inorganic residue remaining after all other constituents are burned away at 75O°C( 1382°F)(ASTM, 1992). Sulfur is the amount of total sulfur that exists either as pyrite (FeS2), inorganic sulfate (FeS04), or organic sulfates (C4H4S) (Leonard, 1979). Currently, pyrite is controlled and total sulfur is monitored. The gross calorific value is the amount of heat produced when a unit quantity of coal is ignited under specified conditions. In this case, a l-g (0.03-oz.) sample of coal is ignited in an isoperibol waterbath and the temperature rise of the water bath is observed. The moisture and ash-free (MAF) Btu is relatively constant for a given seam, resulting in the whole calorific value being a function of the moisture and ash levels (Leonard, 1979).

Jan 1, 1994

By Peter A. Spencer

Much criticism has been levelled at bacterial oxidation over the quantities of air required for successful operation. Examination of the oxidation reactions and the assumptions concerning oxygen transfer made in the literature (1) indicate that the aeration requirements can be much less than those beirig suggested. Observations made on a large scale pilot test have confirmed reasonable aeration levels in extended site operation over a six month period. These aeration levels have implications for the engineering design and the power needed for aeration and agitation. Thus, these parameters effect both capital and operating costs as well as influencing the complexity of the design and normal operation. A number of companies have developed bacterial oxidation cultures intended for commercial ·expl oi tat.ion ( 2, 3, 4). Most of these cultures have been based on Thiobacillus and operate at temperatures between 30°c and 40°c. This temperature range limits their application in hotter regions unless means for both heating and cooling are provided in the design. Thiobacil!us cultures are also reported as not able to oxidize arsenic (III), which may limit the application of these cultures to successfully treat arsenopyritic ores and concentrates (5). BacTech (Australia) Pty Ltd has developed a culture which operates at temperatures above 4o0 c and which has been tested in a large site based continuous pilot plant at up to 55°c over a six month period. The culture showed resistance to high levels of soluble arsenic, allowing the arsenic to be retained in solution for control led precipitation and disposal. Data for. the arsenic precipitates indicated that these waste solids were relatively stable and, under the correct circumstances, were suitable for disposal into tailings dams without causing environmental problems.

Jan 1, 1990

By J. F. McDonald

On December 8th of last year, the new St. Clair River tunnel was holed-through to Port Huron, Michigan. The tunnel, commissioned by the Canadian National Railway, was needed to replace an existing tunnel that had been built between 1889 and 1890, and had remained in continuous operation until the new tunnel was opened to traffic in April of this year. The original tunnel, after more than 100 years of service, was still structurally sound, but was too small to accommodate the double stacked container cars and other advances in the railroad's equipment that had developed over the years. Prior to the construction of the first tunnel, all freight was barged across the river. It was a slow, expensive process, which in winter was sometimes impossible. The nineteenth century tunnel was built in twenty months, utilizing two shields that mined to the middle from each end. The lining, which is still in excellent condition, consisted of bolted, cast iron segments, with an O.D. of 6.4 meters. It was the first sub-aqueous tunnel built in North American, and it's use of compressed air under the river and hydraulic power on the shields may also have been firsts. The digging was done by hand, and the muck hauled out by mule drawn wagons. Boulders and methane gas were reported to be a constant problem during the drive, and compressed air sickness was common, but when the two shields came together in August of 1890, it was reported that the alignment was within 6 mm. The new St. Clair River Tunnel was constructed for basically the same reason as the original. The larger equipment which the railroad is using today would not fit through the old tunnel, and once more they were forced to ferry the cars across the river.

Jan 1, 1995

By S. E. Phillipson

The MSHA Technical Support, Roof Control Division's primary evaluation tool for coal pillar designs is the Analysis of Coal Pillar Stability (ACPS) program. However, ACPS is limited to evaluating interactions between two seams at a time, which is not ideal for complex multiple- seam scenarios. Further, it does not recognize the influence of strata properties in the interburden and cannot be used to evaluate individual pillars. We apply the Rocscience RS2 two-dimensional finite element program as a complement to ACPS. Complex multiple-seam scenarios can be characterized by a modified pillar stability factor where the ACPS single-seam development pillar stability factor is multiplied by the ratio of average single-seam development stress to the stress in the critical pillar at the multiple-seam stage, using the values of o as predicted by RS2. Several series of test examples involving two-seam analyses with isolated remnants, gob-solid boundaries, and high extraction areas of varying width were used to calibrate simulated gob properties such that the ACPS+RS2 method generated results that matched a traditional ACPS Stability Factor to within 13%. As high-extraction areas become wider and deeper, progressively stiffer gob is simulated by increasing the Young's Modulus property in RS2. After achieving calibration with the test series, three examples of complex multiple-seam scenarios were evaluated, using reasonable properties for strata types and thicknesses based on core log data. Resulting modified stability factors are reasonably close to those predicted by ACPS, although affected by units of sandstone in the interburden and gob shadows superimposed on remnant structures. This tends to show that even in complex multiple-seam conditions, applying ACPS to the worst-case interaction should usually result in an acceptable pillar design.

Jun 25, 2024

By J. C. Stankus, S. S. Peng

Many coal seams are associated with soft floor strata. During mine development, if coal pillars are not properly designed, floor heave occurs and causes interruption of coal production. In the severe cases, the section or mine is abandoned. One method for controlling floor heave is floor bolting. This paper describes the demonstration of flour bolting methods in a West Virginia, info coal mine. Three methods were used: vertical full resin bolting, floor truss bolting and floor truss bolting pins a floor slot at the center of the entry. The design of each method and the experimental results are discussed.

Jan 1, 1995

By H. Wen, X. Zhai

"The Jurassic coal fields which lay in west China are the major energy base and contain half of coal resources in China. Due to the gather and degeneration rules, the spontaneous combustion characteristic of Jurassic coal is distinguished with permo-carboniferous coal, which needs to be studied deeply. Programmed heating experiments of five Jurassic coal samples and three permo-carboniferous coal samples from different primal coal fields in West China were conducted to identify the characteristic parameters in the low temperature stage of oxidation and spontaneous combustion. The experiments were carried out under non-isothermal heating conditions up to 180? at the heating rate of 0.33?/min in an air atmosphere. The result showed that oxygen consumption rate, CO gas production rate and heating intensity of all coal samples increased with the rising of the temperature, which of the Jurassic coal was higher than that of Permian-carboniferous coal. The C2H4 gas of Jurassic coal generated earlier, more than that of Permian-carboniferous coal in the process of oxidation and spontaneous combustion. It indicated that the Jurassic coal was easier to be oxidized and spontaneous combustion and the index parameters of spontaneous combustion were different between the Jurassic coal and permo-carboniferous coal.INTRODUCTION Coal was the foundation of industry development, and occupied 70% of primary energy production and consumption structure in China. According to the data of the 3rd coalfield prediction, 39.6% of the total coal resources were located in northwest Jurassic coal field in China [1], where the quality of coal was excellent. The study of northwest Jurassic coal already dated from the 80s of the 20th century, about coal rock composition, coal metamorphism [2], coal-derived hydrocarbons, coal structure [3], etc. The results of these studies showed that the composition and properties of Jurassic coal was obviously different from Permian-carboniferous coal, as well as the characteristic of spontaneous combustion [4]. As a result, the spontaneous combustion characteristic of Jurassic coal particularly needed to be studied. Now more and more methods could be conducted to test the characteristics of coal spontaneous combustion, for example, thermal analysis technology [5-7], programmed heating experiment [8-10] and coal spontaneous combustion experiment [11,12]. In these methods, programmed heating experiment could be conducted to determine the oxygen consumption rate, CO gas production rate and heating intensity quickly."

Jan 1, 2015

By X. Shi, F. -Y. Wang

Automation and robotics are the keys to new intelligent autonomous mining systems that can remove operators from hazardous and stressful mining environments and provide the tools for greater productivity. This paper presents the components necessary for an Intelligent Task Control System (ITCS) for machine control in dynamic unstructured mining environments. In particular, the design details of a controller for an automated excavator are developed. The excavator controller uses fuzzy logic to interpret forces and torques gathered from a wrist mounted force/ torque sensor during the excavation process. This approach enables the transfer of human heuristics and expert knowledge to the controller. Several excavation tests using the fuzzy logic controller are described. These experimental results represent the first step toward an integrated approach that uses force/torque, vision and other sensor data to perform generic tasks in uncertain mining environments.

Jan 1, 1995

By Randy Sandrik

Sampling has evolved at two large underground limestone mines as conditions and product requirements have grown tougher over 100 years of mine life, requiring innovative techniques to insure delivery of high purity limestone. Sampling insures delivery of consistent product to customers at the lowest possible cost. Statistical considerations have evolved from simple data collection to predictive and process capability analysis. Sample methods include borehole samples, face (using a proprietary face-sampling device), and total plant feed automatic, process, and final product sampling. Lessons learned, while keeping costs at historically low numbers, include the importance of geological models, exploration drilling density, face sampling, and blending of ore.

Jan 1, 2005

By Richard B. Berg

California was a major talc-producing State until the late 1980s when production from the deposits in the Death Valley area ceased because of a number of factors which included pressure to discontinue mining in and around Death Valley National Monument, and health concerns affecting markets for tremolitic talc. The states of Montana and Texas now account for slightly more than half of U.S. talc production. Deposits in an area encompassing southern Death Valley and extending east into the Kingston Range were formed by contact metamorphism of carbonate beds in the Precambrian Crystal Spring Formation next to Precambrian diabase sills. These deposits contain ore ranging from high-purity, fine-grained talc to platy, tremolitic talc with high brightness. Deposits of tremolitic talc and talc schist in the Silver Lake District in San Bernardino County resulted from metamorphism of Precambrian carbonate beds intruded by granitic plutons. Northeast in Esmeralda County, Nevada hydrothermal alteration related to Late Jurassic plutons caused talc replacement of Precambrian to Early Cambrian dolomite. A hydrothermal origin is also indicated for talc deposits in the lnyo Range just north of the Death Valley District where bodies of unusually pure talc occur in Paleozoic lime- stone near Jurassic granitic plutons. Talc is now mined from a deposit in the foothills of the Sierra Nevada Range southeast of Sacramento where quartz-mica schist of the Permian Calaveras Formation has been hydrothermally altered to talc. Replacement of magnesite of the Precambrian Allamoore Formation produced talc deposits mined in the Allamoore District of west Texas. This dark-gray talc of low iron content with carbon- aceous material and dolomite is ideally suited for use in ceramics where it makes a white product when fired. Small bodies of platy light-pink to white talc suitable for use as an extender in paint are also mined in this district. In the Llano District of central Texas talc has replaced impure carbonate rocks and serpentinite. All Montana talc production is from deposits in the southwestern part of the State that formed by Precambrian hydrothermal alteration of dolomitic marble. This alteration produced material with high purity that ranges from very fine-grained, massive talc to coarser grained, foliated talc. Markets include pitch control in paper, paint, cosmetics, ceramics, rubber and plastics. In southwestern and northeastern Oregon, talc has replaced serpentinite in the vicinity of Mesozoic plutons. Soapstone for carving is mined from a southwestern Oregon deposit. Deposits of similar origin occur in central and northwestern Washington.

Jan 1, 1995

By Manfred G. Raschke

INTRODUCTION In the past decade, the international coal trade has been undergoing a period of gradual change. This change will continue through the remainder of this century until by the year 2000 the international coal industry will look very different from the industry which existed in the early 1970's. The industry which will emerge from the thirty year period of change (1970-2000) will be different in many ways. -The volumes of coal transported will be much larger. - The primary type of coal traded will be steam coal rather than metallurgical coal. - A much broader group of countries will be participating in the trade both as suppliers and as consumers. - The trade will be dominated by a relatively small number of large producing and trading companies. - The coal mined for international shipment will be primarily surface- mined. – The United States will play a decreasingly important role in international coal trade. In the course of this paper I propose to address three questions which are crucial to the formulation of an understanding of the changes outlined above : (1) Which supplier nations will be most successful in the international metallurgical and steam coal trade in the next decade and a half? (2) What emerging trends will shape the international coal trade in the 1980's and 19901s? (3) Where are U.S. producers likely to fit in this scheme of things? As a background to my remarks, I should note that what follows is based on five years of work in a consulting capacity on coal supply and demand issues worldwide. Although in the course of this work I have had occasion to develop mining and transportation cost figures for all of the countries discussed below--both my own and those obtained from coal producers--it is apparent that success in the marketplace can be determined in some instances by considerations other than costs. Nevertheless, my comments today about international competitiveness will be dominated by cost considerations; there are, after all, not many markets that reward the high-cost producer with success. Let us begin by establishing some criteria for success in the international coal market and then compare some of the producer nations to some of these criteria. The criteria are: - Low delivered cost, - Good quality coal, - The producer's partnership in a joint mining venture with an importer or a consumer of coal, - The producer's international business orientation and commitment to penetrating the market, - The producer's reliability as a supplier, and - Political pressure exerted by the producing country on consumers.

Jan 1, 1986

By R. T. Swindeman

"INTRODUCTION This paper will discuss the topics in the recently released Conveyor Equipment Manufacturers Association’s (CEMA) Belt Conveyors for Bulk Materials, 7th edition, that deal with safety and maintenance. The most effective way to improve conveyor safety is through designing out hazards in the earliest stages of a project. When the safest way to perform maintenance is also the easiest, mechanics will naturally take the obvious and least hazardous approach. IMPORTANCE OF ACCESS Studies have shown that mechanics spend almost one-third of their time accessing the components to be serviced and approximately 25% of all fatal conveyor accidents occur during maintenance1. Chapter 2 of Belt Conveyors for Bulk Materials deals with design considerations. In Chapter 2 there are recommendations for access at the various sections of a typical conveyor for cleaning, inspection and maintenance. While, in some cases, providing access will increase the cost of the conveyor system there can be significant paybacks in reduced injuries, faster maintenance and easier cleaning. Piping and Conduit One of the significant recommendations in Chapter 2 for access is to restrict the mounting of piping and conduit to the conveyor structure in the Loading and Discharge zones of a conveyor. Piping and conduit are more permanent fixtures than maintainable components and should be located out of the way of components needing frequent maintenance. If electricians and pipe fitters are given convenient locations to make their runs they will natural use them. Flexible conduit and hoses can be used to connect to components from pipe racks and cable trays which further enhances maintenance. Access for Cleaning Another critical aspect of access is for cleaning. Approximately 33% of all fatal conveyor accidents occur while cleaning spillage and carryback under and around conveyors2. In the loading zone having sufficient height under the conveyor for cleaning increases the cleaning interval and allows for safer cleaning. In the discharge zone having adequate access for belt cleaning installation has a direct effect on the ability to install a proper cleaning system and perform maintenance."

Jan 1, 2015

By M. Fig, A. Juganda, M. Zurhorst, J. Brune, C. Strebinger, G. Bogin

"Understanding the airflow patterns in and around the longwall panel can help to identify poorly ventilated areas that may be prone to methane accumulation. Ventilation network modeling provides quick simulation time, and flexibility in adjusting airway parameters and ventilation controls. Such modeling is effective for analyzing linear ventilation networks in underground mines, but cannot compute flows in caved areas of hard rock mines or longwall gobs. The use of Computational Fluid Dynamics (CFD) enables a more detailed investigation of the interaction between the airflows in these caved areas but requires much longer computational times, designing complex meshes and determination of a variety of modeling parameters. Airway friction factors and ventilation controls are simple to implement in a network model but can be difficult to model and adjust in CFD. This paper will focus on using mine ventilation network simulation to identify and analyze key parameters that are affecting airflow distribution in and around the longwall panels, prior to more detailed analysis with CFD modeling, using the example of a longwall coal mine. INTRODUCTION In longwall coal mine ventilation systems common in the U.S., the main purpose of bleeder ventilation is to dilute methane gas and prevent the formation of explosive gas mixtures in the caved, poorly ventilated gob areas and adjacent mine workings. In longwall operation, these critical areas include the development headings inby the longwall face, and the gob. Methane-air explosions in these areas may be ignited by spontaneous combustion, rock-on-rock friction and other sources. Although rare, ignitions due to rock-on-rock friction caused by roof falls caving into the longwall gob are possible and were suspected in the Willow Creek mine explosions in 1998 and 2000 (Elkins et al., 2001; McKinney et al., 2001). Rock-on-rock frictional ignitions are difficult to prevent, as they occur in inaccessible areas. Therefore, rendering the gob area inert is essential to prevent the formation of explosive mixtures. Research by Gilmore et al. (2015) and Brune et al. (2015) has shown that gob inertization can be a difficult or impossible when using bleeder systems, since the flow of gases through the gob depends on the gob permeability and the amount of fresh air leaking from the face and the immediate roof caving conditions cannot be controlled by the mine operator. Having the ability to predict the location where explosive gas zones (EGZs) form inside the gob will be helpful for designing the best ventilation setup to minimize explosion and fire risks."

Jan 1, 2018

By A. Spearing

According to a 2000 NIOSH report, about 100 million rock anchors are installed annually in coal mines in the USA. Most coal mines have conditions that are conducive to corrosion of the rock anchor and ancillaries (such as plates), yet the effect of this on the performance of the anchors has not been adequately researched and its effects are not understood or quantified in the USA. There is considerable research into corrosion in civil engineering applications on surface and underground but the corrosion of coal mine rock anchors is not necessarily the same because: ? In underground civil structures, water ingress is usually stopped as part of the construction process. ? Many rock bolts in mines are only partially resin grouted leaving part of the reinforcing member exposed to corrosive conditions. All cable bolts in coal mines are only partially resin grouted. ? Even when mine bolts are fully grouted, shrinkage cracks occur and the rock stresses can change due to adjacent mining that can cause the resin column around the bolt to fracture further under external shear or tensile stresses. Most coal mines therefore have ideal conditions for bolt corrosion.

Jan 1, 2010

By Roger S. Dewey

1.1. INTRODUCTION Despite indications of a general economic recovery in the U.S. during the mid-19801s, mine operators have not generally shared in the benefits of these reported better times. Budgets have not rebounded, borrowing is tougher, parent companies' pockets are not as deep as in previous years, and margins are not any better -- if there is any left over at all. Managing capital equipment budgets is always a challenge, and the last five years of stretched equipment lives make these decisions more tenuous. Delays and avoidance of replacements due to tough times inevitably makes those decisions increasingly difficult and usually more expensive The purposes of this paper are to present. a brief refresher outline of the fundamentals of equipment replacement analysis, to suggest a number of papers where analysis methods are explained in greater detail. and to recommend the use of a widespread microcomputer software capability (1-2-3) as the easiest path to a much-needed solution for a very difficult, and usually under-supported management decision problem 2. REPLACEMENT DECISION POLICY Investments in equipment replacements must compete for capital with all other investment alternatives. Capital for replacements of ten represents a greater commitment than do the new projects which a company might handle in a given year. But. sadly, formal policies for standardized analysis of replacements rarely exist, even in major companies. Yet this policy can be very significant in determining the competitiveness of a firm. Whereas many replacement decisions are based on cost minimization, economists and financial analysts agree that wealth maximization or return on investment is the superior criterion. Though the difference may seem slight, agreement on a firm's financial objective is vital. Replacement policy should be straight- forward. have a logical basis, and a proper level of sophistication. There are several reasons to develop a policy for replacement decision-making: [I] 1 - equipment's optimal economic life is nearly always shorter than its physical life; 2 - mine life often exceeds equipment life, so management must face these decisions routinly 3 - replacement capital costs, on an undiscounted basis, can run 25 to 75% of original capital 4 - technological changes may result in a newer machine or system which can operate more efficiently, more safely. or less expensively 5 - estimates should be made consistently in the fundamental areas of life expectancy, availability, utilization. price escalation, taxes 6 - long-term and short-term budgeting without decent data and analytical capability is nearly impossible, or at least ineffective Policy development assumptions which must be considered include: the planning horizon, cost patterns, interest rates, availability of capital, replacement vs. expansion, technology advances.

Jan 1, 1987

By H. R. Manouchehri

The responses of calcite, feldspar, and quartz minerals In a laboratory free fall electrostatic separator, before and after tribocharging with stainless steel, PVC, and copper plates, have been investigated. The effect of H3BO3 and BaCl2 chemicals pre-treatment on the electrical properties of the minerals is examined. The changes in the electrical properties are discussed with the determined charge, dielectric constant, and electrical conductivity of the mineral samples. Electrical properties of the minerals and their responses to the electrical field during separation, after tribocharging and chemical pre-treatment, are explored for the need to characterize the electrical behaviour of the minerals.

Jan 1, 1998

By J. Paul

Mining engineers in charge of open pit mine planning very often face decision making situations dealing with the selection of the most economical method for the removal of overburden. Ripping versus conventional drilling and blasting are the options considered. The choice of a particular overburden removal method depends upon the physic-mechanical properties of the overburden material as well as the various cost factors involved in the process. The analysis of techno-economical factors involved in different methods of overburden removal needs detailed study and investigation by a technical expert. But the expert system "Fragmentation System Design" has been created in a way such that it will help and expedite the decision making process relating to overburden removal in surface mines. Furthermore, this expert system can be used for detailed design aspects of overburden removal in open pit mines.

Jan 1, 1988

By Bruce Johnson

This paper is not written to "break new ground" in computer applications; it is just a treatment of how an operating metal mine utilizes a mainframe computer for planning, analyzing, and reporting on the ventilation and cooling systems. The Unisys mainframe computer at the mine site is used in programs that analyze the ventilation network, keep records on various ventilation installations, calculate the results of measurements and produce reports on ventilation conditions in the working places and on the main air distribution, and plan and analyze the cooling system. All the programs are interactive to terminals. There are a series of data files that are generated by some programs which may be used by other programs. Most of these programs have been developed in-house. The computer is also used as a word processor via a vendor-supplied text editing program to produce memos, letters, and to keep up-to-date lists of equipment used.

Jan 1, 1989

By L. Giraldo, S. Cotten

"INTRODUCTION The vision for a “Mine Escape Vehicle” (MEV) is to provide capabilities to better enable underground travel to allow miners to escape to safety in the event of a major mine emergency such as a fire or explosion. Enhanced transportation and survival capability such as a MEV may have minimized or eliminated the loss of life associated with several of the mine disasters that occurred in 2006, which together resulted in the deaths of 19 miners. Although the most desirable response in an emergency is for the miners exit the mine, if escape proved to be impossible, the miners could use the vehicle to proceed to an underground point of refuge to await rescue. Under a NIOSH contract issued in April 2008, Raytheon developed a conceptual vehicle design including (1) the capacity to provide life support functions for a number of miners, (2) operate in a reduced oxygen atmosphere with little or no visibility, and (3) travel at speeds faster than miners could walk out of the mine. The proposed MEV concept envisioned modification of a personnel carrier (a.k.a. a “mantrip”) that would be used every day during normal mine operations, not a specialized vehicle reserved only for or dedicated solely to escape. The MEV concept also included escape aids that are detachable from the vehicle in the event that the vehicle must be abandoned on the way out of the mine and the dismounted miners had to proceed on foot. To advance MEV development, NIOSH awarded a second contract in 2010 to Raytheon to build, test, and evaluate the performance of a proof-of-concept MEV that culminated in a 7-month performance evaluation of vehicle in an Eastern Kentucky coal mine (Figure 1). User feedback and lessons learned from the proof-of-concept vehicle evaluation provided support for the general MEV approach, guidance related to the practicality of MEV capabilities, and indication of specific technology shortcomings for this application."

Jan 1, 2015

By O. Alvarez-Campos

Two porphyry copper orebodies, the North and Central MM orebodies, have been found through regional and structural geologic works, about 5 Km south of Chuquicamata, under a gravel bed of approximately 100 m and in the west side of the West Fissure. The mineralization is emplaced in a coarse granodioritic porphyry, predominantly with sericitic alteration. In the North MM ore-body, with 200 million metric tons of 1.0% Cu, the mineralization is mainly chalcopyrite, bornite, digenite and molibdenite. In the central MM orebody, with 700 million metric tons of 1.3% Cu, there are large veins of enargite, chalcocite and bornite, the last one increasing in depth, separated by chalcopyrite and pyrite zones; in these veins there are interesting gold and silver values. Both orebodies have an upper enrichment of chalcocite and covellite, with pyrite envelope. According with these characteristics, the MM orebodies could he the upper part, with sericitic alteration, of the Chuquicamata porphyry copper system, displaced by the West Fissure system movements, but we couldn't eliminate the possibility that MM can be a new orebody, different of Chuquicamata.

Jan 1, 1993

By Van E. Housman, Stephen D. Hoffman

The Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA), also known as "Superfund", requires a listing of sites that have known releases or threatened releases of hazardous substances, pollutants, or contaminants throughout the U.S. When EPA determines that a significant threat exists, it places the worst contaminated sites on the National Priorities List (NPL). CERCLA provides EPA broad authority to clean up hazardous sites that threaten human health and the environment. There are currently 52 sites on the NPL that were placed on the list because of high human health or environmental risk as a result of non-coal mineral extraction, beneficiation, or processing operations. This list covers mining sectors from aluminum to zinc. While some of these sites were abandoned, many are still operating. (There are additional mine sites that have been recently proposed to be included on the NPL that are not included in this paper.) EPA is continuing to develop a mining program to address human health and environmental threats from active non-coal mines. EPA has performed a comprehensive study to assess the waste management practices at all of the 52 mine sites on the NPL. In addition, EPA is continuing to collect information on the specific mining sectors (i.e., gold, copper) that represent many of the NPL mine sites. One of the goals of this effort is to attempt to identify the types of mining practices that lead to human health and environmental problems at the NPL mine site. EPA estimates that there are currently 500 to 1,000 active mines (not including placer operations). While some mining NPL sites began operations before the turn of the century, only a handful of the NPL mines entirely ceased operations prior to 1970. Of the 52 NPL sites studied by EPA, 12 are currently active. By definition, these mines represent current mining practices. Approximately 17 additional NPL mines that ceased operations between 1970 and 1990 represent some degree of current mining practices. Therefore, at best, less than half on the 52 NPL mine sites can be said to definitely represent past mining practices. Although some mining waste management practices have changed over time, the basic technology for extraction and beneficiation of mineral ores have remained fairly constant over the last fifty years. While the use of acid to leach copper dumps, the use of cyanide to leach gold in heaps, and the spread of solvent extraction techniques has changed some aspects of mining, the basic operation of removing ore from the ground and concentrating it through beneficiation has remained fundamentally the same as when most of the non-active

Jan 1, 1992