Search Documents

By J. W. Mahar, E. J. Cording, F. L. Gau

INTRODUCTION The Washington, D.C. rapid transit system (METRO) when completed will consist of 98 miles of double track rail. Fifteen miles will be tunneled in rock and 12 large underground rock chambers will be constructed at station locations. The University of Illinois is under contract to Metro to provide observations and instrumentation services in the initial phase of construction. The work is coordinated through DeLeuw, Cather & Co., the General Engineering Consultant to Metro. The program is designed to monitor construction conditions as well as to provide information useful for the design of future rock tunnels and rock chambers in the Metro system. This paper presents the results of observations in the rock tunnels constructed to date. Most of the observations are in a 5000-ft-long, 30-ft-wide, double track tunnel in downtown Washington, D.C. Observations were also made in single track tunnels, shafts, enlargement areas, and pilot tunnels, and are being made in a large rock chamber 700 ft long, 76 ft wide, and constructed at shallow depth in a schistose gneiss. One of the major objectives of the observational program was to determine the orientation and character of joints and shear zones and to evaluate their effect on support requirements for various tunnel orientations and configurations. The consistency of geologic features throughout the Washington area has made the results of the initial study applicable to evaluation of support requirements on future tunnel contracts. The first section of this paper summarizes the geologic conditions in the tunnel and their effect on overbreak and rock movement.

Jan 1, 1997

By Yuuichi Umeki, Yuusaku Tominaga

In order to keep good air condition in any specific branch such as coal face and/or heading in an underground coal mine, effective factors of all the branches with respect to the specified branch have been investigated, using computer simulation. Main results of the paper are as follows; 1) A branch in a network is classified to one of three classes of effectiveness to increase, to decrease and not to change airflow rate in the specific branch by altering aerodynamic resistance in the branch. 2) Distribution of position of branches, belonging to each class, related to a specific branch is one of the macroscopic characteristic of a network which is the inherent property of every network. 3) A relation of the aerodynamic resistances of any two branches to keep a constant airflow rate in the specified branch is shown as a monotonous curve. 4) Ventilation transition diagram with the rate of airflow in the two branches as coordinates, and for different rates of airflow in the specific branch as the parameter, is found to be straight lines. 5) Existing range of airflow rates In the specified branch is given as a parameter in the enclosed area in the ventilation transition diagram. Moreover, an expert system to assist ventilation control using a transition diagram of airflow rate is introduced in this paper.

Jan 1, 1991

By S. K. Mishra, S. B. Kanungo

Because conventional (physical) methods of ore dressing are not suitable for reducing the phosphorus contents of high-phosphorous manganese ores from Andhra Pradesh (AP) and the adjoining area in southern Orissa, India, the adoption of chemical methods becomes imperative. An attempt was therefore made to reduce the phosphorus content of partially beneficiated manganese ores from AP by roasting with sodium carbonate and then leaching with hot water. However, due to the higher phosphorus contents of the manganese ores from Nishikhal mines in southern Orissa, and because of their apparent resistance to dephosphorization by roasting with Na2CO3 alone, a mixture of Na2CO3 and NaCl was found to be necessary to reduce the phosphorus content to below 0.15%. Free-energy calculations at 700°C and above indicated that Na2CO3 (or Na2O as the active component) is a more active reagent than NaCl. Various process parameters, such as the temperature and time of roasting, the amount of sodium carbonate and the temperature and time of leaching, were studied to arrive at the optimum conditions for dephosphorization.

Jan 1, 2000

By A. F. McKown, P. E. Sperry, W. L. Fourney, D. E. Thompson

INTRODUCTION Underground drill and blast excavation is usually accomplished with small diameter holes loaded with high energy explosives. The detonation pressures are extremely high and an extensive amount of energy is dissipated in the process; however, very little of this energy is used to create the specified fracture planes required for excavation. The available energy is expended in producing radially outgoing stress waves, in crushing the adjacent rock, and in producing a dense, randomly oriented radial crack pattern about the holes. This causes several undesirable effects: 1. Overbreak at the perimeter, which results in more muck to remove and extra concrete or shotcrete to fill the voids. 2. Damage to or loosening of the remaining rock at the perimeter which may result in the need for additional support measures. 3. Ground vibrations and/or airblast, which could result in damage to nearby structures and complaints by people living or working in the area. Several steps may be taken to minimize these effects. Where control of the perimeter is desired, smooth blasting techniques are generally employed in which the spacing and burden of perimeter holes are reduced and lighter, decoupled charges are used. Where vibration damage to structures is feared, control is generally exercised by limiting the charge weight per delay period so that the ground vibrations at the nearest structure do not exceed a peak particle velocity of two inches per second. Where blasting complaints may be a problem, con-

Jan 1, 1979

By Giovanni Osellame, Jean Habimana

"The Montreal Metro Blue Line Extension Project is part of a metropolitan Program that was launched in 2009 by the Transportation Ministry of Quebec to add additional extensions to existing metro lines in the cities of Montreal, Longueil and Laval with the intention to meet current demand and future growth within the Montreal agglomeration. Specifically the Blue Line Extension Project will add five underground stations to the East of the Montreal. The paper addresses the preparation and the implementation of a three-step geotechnical and geo-environmental investigation program and preliminary design considerations such as the selection of a preferred horizontal and vertical alignment, the selection of construction methods based on previous local experience and current industry trends, as well as preliminary sizing of underground infrastructures. PROJECT BACKGROUND An agreement between the three mayors of the Montreal Metropolitan City agglomeration, namely, Montreal, Longueil and Laval prompted the Government of the Province of Quebec to create a project office to oversee the studies of extending the existing metro network. The last extension of the existing metro network was completed in 2008 with the Laval extension, which consisted of adding three stations from the existing Orange line. The current extension Program consists of three different extensions, namely extending the Orange Line to Laval and finishing the loop, extending the Blue Line to the East of Montreal by adding five stations, and adding five stations on the Southshore of the St-Lawrence River for the Yellow Line extension. The extension program also requires the construction of an underground storage and maintenance garage located to the north-west of the existing Cote-Vertu station on the Orange line. Figure 1 shows the overall extension program with the existing network."

Jan 1, 2016

Adequate ventilation of coal mine working faces is the single most important technique for controlling respirable dust and methane. Choosing the right technique presents some tough questions. Bureau research has shown that to control respirable dust you must contain the dust near the face, keeping rollback (turbulence) to a minimum. For methane the most effective approach has been to use a blowing brattice or tubing and to create turbulence and disperse the face methane, allowing it to pass over the machine and into the return. It is immediately apparent that the two approaches may counteract one another, thus complicating the decision as to which system may be best for a given situation. At present, Bureau research has developed two successful machine-mounted face ventilation systems to meet these different needs and allow deeper cutting. The fan-powered dust scrubber is designed to control dust primarily associated with blowing face ventilation systems. The spray fan controls methane on exhaust-ventilated sections.

Jan 1, 1988

By J. Peterson, P. G. McKneight, R. W. Riggle

"In today’s tough mining environment, the key difference between surviving and thriving is how effectively miners optimize their mining operations. This paper explores the compounding effects material fragmentation has on mining costs and productivity. Starting with Drilling & Blasting and moving through Loading, Hauling and Crushing, we will illustrate the opportunities to improve operating costs and thus reduce the Total Cost of Ownership (TCO) of the total mining system. Material size and volume requirements are defined by the needs of the mill or plant, and drive the rest of the mining operation from the bench through the primary crusher. At the start of the cycle, where the rock mass is drilled and blasted, the degree of fragmentation and the muck pile configuration is determined, as are the effects on cost and productivity of all subsequent operations. The cost of managing oversize material, including secondary handling, overloading, reduced diggability, higher load factors, extra pass loading, increased wear factors and reduced throughput rates are all opportunities for improvement. INTRODUCTION Having visited many mine sites, customers are asking about the end to end mining value stream from loading to the crusher and how to measure the cumulative effects on each part of the mining value chain. All too often improvements with the drilling and blasting may impact fragmentation but do not improve the diggability so the net change on cycle times or fill ratios is perceived to be negative at the point of loading but they may have a measured improvement going through the primary crusher. This makes it imperative to measure performance at each segment of the overall cycle and not just to the crusher but thru it. The mine material process originates with solid rock, in-situ, and progresses to the output of the primary crusher. Once the material has passed the primary crusher the fragmentation size will be fairly consistent and promote consistent throughput of the plant or mill. In late 2015 a team was conducting a reassessment visit to a mining site where we had conducted the original assessment the previous year. Though many recommendations had been implemented some had been so recent they had not resulted in the expected improvements. Several of our discussions kept returning to the impact fragmentation has to both the individual components of the mining cycle but also the effects compounded throughout the end to end process. Let’s move on to the big picture before we zoom in on any specific operation. To get from native solid rock in the ground to a concentrate or a saleable rock product we have the same steps from one end of the chain to the other. We start with a good geological understanding of the rock type, characteristics and structure to design a program to drill and blast the rock. The height of the bench is relevant to the annual production requirements and the specific digging equipment models best sized to make that production possible. The equipment selection influences the bench height which has a minimum and maximum hole diameter to maintain a safe blasting operation. The diameter of hole burden and spacing all contribute to a good distribution of explosives in the rock mass that maximize the fragmentation and preconditioning of the rock when blasted. The timing and sequencing of hole initiation will yield a fragmentation ratio and diggability factor. Fragmentation size adjustments will change the meters drilled per cube and the explosives consumption will change accordingly. Drill cost is measured by meter drilled so a direct relationship exists between cost and fragmentation sized achieved."

Jan 1, 2017

By Chen L. Lin, Luis R. M. Bittencourt, Jan D. Miller

Recently research efforts have been made to obtain a high-purity gibbsite concentrate, suitable for first-class alumina refractories, from a Brazilian bauxite ore containing gibbsite (50%), quartz (35%),and kaolinite (15%). Detailed polished-section microprobe analysis was used to describe the liberation characteristics of the ore. Experimental results suggest that the kaolinite liberation characteristics can be described by King's liberation model and that only about 11% of the kaolinite is expected to be liberated at a particle size of 75 µ. Bench-scale experiments for the flotation of gibbsite/kaolinite from quartz using alkyl sulfates as collectors were particularly successful at pH 2, and under appropriate conditions a concentrate containing 93.0% A1 0 (calcined basis) was obtained 2 3 at a gibbsite recovery of about 96%. Subsequently, the more difficult separation of kaolinite from gibbsite was accomplished by kaolinite flotation from the alumina concentrate with a quaternary ammonium salt at pH 6 to produce a high-purity gibbsite product, 97.4% A12O3 (calcined basis), at an overall gibbsite recovery from the bauxite flotation feed of about 90%.

Jan 1, 1990

By J. A. Organiscak

Water spray applications are one of the principal means of controlling airborne respirable dust in coal mines. Since many coals are hydrophobic and not easily wetted by water, wetting agents can be added to the spray water in an effort to improve coal wetting and assist with dust capture. In order to study wetting agent effects on coal dust capture, laboratory experiments were conducted with three wetting agents used by the coal industry on -325 mesh sized Pocahontas No. 3 coal dust. Significant differences in coal dust sink times were observed among the three wetting agents at water mixture concentrations of 0.05%, 0.1% and 0.2%. The best wetting agent as identified by the coal dust sink test was only tested at the lowest 0.05% water mixture concentration and was found to have a negligible effect on spray airborne dust capture. Water spray airborne dust capture results for all three wetting agents tested at a 0.2% water mixture concentration showed that all three wetting agents exhibit similar but small improvements in dust capture efficiency as compared with water. These results indicate that the coal dust sink test may not be a good predictor for the capture of airborne dust. Additional research is needed to examine if the coal dust sink test is a better predictor of wetting agent dust suppression effects during cutting, loading, conveying and dumping of coal products by comparison to airborne dust capture from sprays.

Jan 1, 2013

By Bryan Morris

Quebrada Blanca (QB) is a copper project located in the semi-arid Andean highlands of northern Chile. The operation is situated 170 km ( 105 miles) southeast of the port of Iquique and 30 km (18 miles) west of the border with Bolivia, at an altitude of about 4300 m (14,000 ft) (Fig. 1). The QB ore body is a secondarily enriched porphyry copper deposit containing reserves of 85 Mt (93 million st) grading 1.3% copper. Underlying the enriched zone is a significant primary ore zone containing several hundred million tons grading about 0.5% copper. In the late 1970s and early 1980s Falconbridge and its affiliates spent $20- $30 million exploring the deposit and conducting feasibility studies. Falconbridge, however, decided not to develop the property. It was returned to its owners, Empresa National de Mineria (ENAMI), a Chilean state mining corporation. In 1988, ENAMI announced its intention to privatize the property through public bidding. Cominco Resources, then 61% owned by Cominco Ltd., examined the property and the extensive data base developed by Falconbridge. In conjunction with its parent company, Cominco Resources submitted a proposal to ENAMI to construct an open- pit mine, with heap leaching and solvent extraction/electrowinning (SX-EW) processing facilities. The plan would use patented heap leaching technology developed by Sociedad MineraPudahuel (SMP), a privately owned Chilean mining company. At that time, a $150-million project that would produce about 45 kt/a (50,000 stpy) of cathode copper was envisaged.

Jan 1, 1993

By W. P. Arnott, P. Nascimento, X. L. Wang, K. C. Kocsis, S. J. Taylor, H. Firouzkouhi

We report the first spectral photoacoustic measurements of silica, coal, and kaolinite dust absorption coefficients from 11 to 13 μm at 5 nm resolution made with a tunable quantum cascade laser. This is important because airborne silica dust and coal dust within mining environments continue to be a problem for mine workers and staff due to their severe health effects on the respiratory system, while other dust types are potentially interferents to their detection. Our real-time spectra compare favorably with the non-real-time filter-based Fourier transform infrared spectrometer (FTIR) spectra obtained using the sampling system developed by NIOSH for their end-of-shift method to determine silica dust concentrations using a portable FTIR. We discuss our new dust generation system and instrument testing chamber. We also show that our PM4 silica mass concentration measurements by a low-cost air quality sensor (SPS30) are in good agreement with the TSI Aerosol Particle Sizer instrument, the NIOSH end of shift method, gravimetric mass, and correlate well with photoacoustic light absorption measurements at a wavelength where silica absorbs strongly.

Aug 20, 2022

By S. Amirshenava, S. Nadimi

"Premature and unplanned mine closure can result in significant adverse impacts on the environment and community and need to be managed appropriately. Risk management techniques can reduce the negative impacts and risks of early mine closure. Risk Assessment 3D Model, is an efficient tool to quantify risk. The aim of this paper is to identify the mine closure risks in Choghart iron ore mine, and calculate the overall mine closure risk level. The result shows that 51.4% of assessed risks have low risk level and the overall risk level of early mine closure is low. Keywords: mine closure, risk assessment 3D model, Choghart iron ore mine INTRODUCTION The modern mining life-cycle can be divided into three main stages; exploration, mining (opening and production) and post mining (mine closure, and reclamation). Mine closure is the critical component of the modern mining life-cycle and it refers to the period of time when the operational stage of a mine has permanently ceases (Heikkinen et al, 2008). Planned closure occurs due to the depletion of ore reserves, but sometimes it is premature. Laurance (2006) shows that only 25% of mine closure in the past 30 years was due to resource depletion and in 75% of the cases the mines were closed for the other reasons. Ghanbari et al (2010) demonstrated that 48.6 % of copper mine closure in the past 100 years was due to resource depletion and 51.4 % of copper mines have been closed due to other reasons. The main reasons of premature mine closure are as follow (Laurance, 2006; Ghanbari et al, 2010; Maiti, 2013): • Economic, (low commodity prices or high costs) • Geological, (over-estimation of grade and tonnage) • Geotechnical (adverse geotechnical conditions) • Technical (equipment failure) • Regulatory, due to safety or environmental breaches • Social or community pressures • Closure of downstream industry or markets • Flooding or inrush Minaei Mobtaker and Osanloo (2013) developed a mine closure prediction model based on the data collected from closed iron ore mines in the past 100 years. They showed that economic factors, exhaustion of ore reserve and geological conditions are the main reasons of iron ore mine closure. They treated mine closure as a decision making problem in order to predict the causes of mine closure, including the uncertainties of some mine plan parameter such as iron ore price, production and consumption."

Jan 1, 2016

By Bekta? Uz

In this research, geological characteristics of sand quarries around the village, Kemerburgaz Akpinar, are studied and the mineralogical, petrographical, chemical and technological characteristics (such as sieve analysis, relative density, water absorbtion etc.) of the sand samples, obtained from the area are explained. In the general area sand' quarries, being in lacustrine formations belonging to Neogen, the stratigraphic location of the sand occurences take place at high levels of these formations, geologically. All of this pattern, being under 1 mm with a ,particle dimension, it ranges from 0,5 mm in the quantity of 99 % to 0,25 mm in the quantity of 15 relative density is 2,65 g/cm3 ; water absorbtion is 0,9%. Mineralogically, the sand samples contain Quartz (84%), Feldspar (3%), Calcite + Aragonite (10%), Pyroxen+Amphibole (1-2%), Garnet+Tourmaline (0.5%), Olivine (0.1-0.5%). Besides, sand samples contain SiO2 with the quantity of above 90%. Containing Quartz at high levels for mineralogical, petrographical and chemical characteristics, Akpinar sand will be evaluated as silica sand when the carbonate mineral is removed with the method of ore preparation such as leaching.

Jan 1, 2005

By William Gleason

During the past five years, mining operations have had access to press technology for piping and joint fittings that can save owners a significant amount of time when installing or replacing pipes by eliminating the need for welding or threading. Viega, with North American headquarters in Wichita, KA, entered the mining sector in 2009, adding to its already expanding industrial sector. Since then, the company?s global engineering department has paid considerable attention to its industrial division, bringing its expertise in plumbing solutions for residential and commercial buildings to the mining and mineral extraction industry. ?We have a lot of applications in the mining industry.?We have a lot of applications in the mining industry throughout the United States, Canada and Mexico and continue to expand in the mining industry,? Tom Shields, Viega?s director for industrial accounts explained. ?Since we made the decision to increase our presence in the industrial markets, we have been aggressive and more than 240 applications have been approved by our engineering department in Germany.? Getting approval from Viega?s engineering department is no small feat. During a tour of the manufacturing facilities in Ennest and Großheringen, Germany, Mining Engineering, as well as a select few other publications and clients, were shown Viega?s manufacturing process. At the Ennest facility, hundreds of millions of fittings are produced, and each one is inspected mechanically and with a laser at the end of the production line. With four production facilities in Germany and one in the United States, Viega is able to ship to anywhere in the world. The company distributes everything from fittings to stainless steel pipe.

By John J. Sammarco

"The mining industry has made great strides in making mining safer and reducing the occurrence of mine disasters. Nevertheless, sometimes miners encounter smoke while trying to escape from a mine. Underground miners use different visual cues to help them escape from a smoke-filled environment. Foremost, miners look for primary and secondary escapeways that are typically indicated with reflective markers of various colors, with at least 11 colors available from manufacturers. Federal regulations require that escapeways be marked, but they do not specify the colors to be used. Thus, no standard color code exists and some colors can be more difficult to see in a smoke-filled mine.Researchers at the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) tackled this problem by taking a human-centered approach to provide miners with better visual information that would improve their ability to see escapeway markers in smoke, thus enhancing their ability to self-escape. What marker colors does your mine use?Does your mine use blue retro-reflective markers to indicate primary or secondary escapeways? Is your mine ready to purchase new or replacement retro-reflective markers? Color is important and blue had the poorest visibility as determined by OMSHR’s recent research investigating the visibility of markers in smoke. OMSHR researchers are not alone in their interest to improve a miner’s ability to escape - specifically when their efforts are hampered by smoke. For instance, there is a LinkedIn Mining Safety subgroup called "Standardized Color Code for Escape Ways and Returns in Underground Mines," and a recent National Academy of Sciences report recommended the development of humancentered technologies to enhance self-escape from underground mines. The mining industry has a common goal of helping improve miner safety, especially when it can be done by way of a simple and relatively low-cost solution of using escapeway colors that are more visible."

Jan 1, 2014

By P. Anciaux

The EUs? manufacturing and construction industries are vital to Europe?s economy. They rely heavily on a steady supply of materials which meet appropriate quality criteria and are available at a competitive price. The steadily rising global demand for (non-energy) raw materials due to increasing consumption in upcoming economies such as China, India and Brazil, is in some cases leading to rapid price increases, but also supply disruptions which affect the European industry chain. These considerations are at the basis of new policy initiatives that are being prepared by Enterprise and Industry Directorate-General in relation to the competitiveness of the European metals industry. Over the last year the raw materials supply issue has increasingly become the topic of de-bate among various stakeholders. In July 2006 the European Economic and Social Committee adopted an opinion on risks and problems associated with the supply of raw materials to European industry. It is therefore important to identify and analyse the future needs for European industry, the possible constraints and impacts on its competitiveness. The raw materials supply issue should also be looked at from the view-point of the EU extractive industry, which plays an important role in supplying raw materials to the downstream industries and which faces very specific challenges. Within the Enterprise and Industry Directorate-General the different factors that influence the competitiveness of the non-energy extractive industry are being assessed, in order to help identify policies and actions which could contribute to and enhance the competitiveness of the industry.

Jan 1, 2007

By R. Jedrzejczak

Endako Mine is an open pit molybdenum mine located in the north central region of British Columbia, Canada, approximately 160 km. west of Prince George. Production for the latter part of 1992 is expected to average at 63,500 tonnes per day of which 27,000 tpd constitute the mill feed. This production is achieved with five 15 to 19 cu. yd. electric shovels, six Euclid R190 and two Unit Rig M120 diesel-electric haul trucks, and three 121;.1 inch electric rotary drills. There are three ore zones delineated into pit areas called the Endako, Denak East and Denak West. Present mill feed source is the South East stage of the Endako Pit while the stripping is carried out in the South Wall stage also of the Endako Pit. The mine high grade aggregate is reduced in the primary and secondary crushing circuits before processing in conventional RM/BM/flotation circuits. The majority of the Molybdenum Sulphide (MoS2) is roasted on site to produce technical grade Molybdenum Oxide (MoO3) while a portion is further refined and treated to yield a 99.9% pure Molybdenum Sulphide (MoS2) "Ultrapure" product.

Jan 1, 1993

By Klein E., Kinscher J., Lizeur A., De Santis F., Lhoumaud E.

Seismic repeaters are rarely observed phenomena in underground mines. However, recent studies in Garpenberg mine (Sweden) have demonstrated that seismic repeaters and multiplets may represent significant portion of the total number of microseismic events (> 80 %) related to excavation operations. Detailed seismic analysis, involving template matching, multiplet clustering, double-difference relocation, source parameter and mechanism estimation, and interevent time analysis, suggest that seismic repeaters represent brittle frictional parts (asperity) of creeping, planar shaped, pre-exiting structures of several meters length. It is furthermore suggested that seismic repeater occur preferentially in weak rock-mass materials (e.g. talc) associated with strengthening friction behaviors. These results may imply that postblast related stress redistribution may be governed by “silent” aseismic movements in preferentially weak rock mass materials, what questions the reliability and performance of seismic monitoring to survey stress evolution during excavation operations. However, once the seismic and aseismic coupling processes and the geological nature linked to repeater occurrences are better understood, their detailed monitoring bears also opportunities to survey and quantify aseismic post-blast stress transfer. Here we present ongoing investigations on repeater occurrences aiming at better understating on their geological and geomechanical origin. Furthermore, we try to develop advanced monitoring tools helping to quantify aseismic slip and to provide criteria for seismic hazard as asperity density and the related potential to generate larger dynamic rupture zones. For this respect a local monitoring network has been set up close to certain repeater target families. Furthermore, geological well log drilling throughout repeater occurrences as well as geotechnical strain measurements (e.g. extensometer, optical fiber etc.) are currently conducted to provide crucial information on the geological nature of repeater and to quantify and characterize background creep induced from excavation.

Apr 26, 2022

By Katherine Hynard, Colin Eustace

Development quarterly mine plans is generally time-consuming and requires consideration for many operational constraints and competing objectives. With lengthy turnaround times, there is often limited opportunity to adjust the quarterly plan details to account for differences between actual state of the mine operation at the time of execution and expected state at the time that the plan was developed. Actual mining task completion times can vary significantly from the expected task completion times, due to many factors. In the absence of revision to account for differences between the planned and actual state, resource allocations and mining sequences, embodied in the quarterly mine plan may no longer be the best approach at the time of execution to achieve an efficient mining operation. Simulation and optimisation tools can be used to support rapid refinements for development and execution of weekly mine plans. When initialized with an operations data feed to establish the actual state of the mine operation, optimisation models can be used to facilitate both automation and revision of the quarterly plan to produce a weekly or daily plan for execution. This approach can remove much of the manual burden of revision if the existing quarterly plan no longer represents the best approach to meeting production objectives. Following initialisation with mining actuals, simulation models can provide a representation of the range of likely mine operations outcomes. The models can be used to accelerate the planning process by providing visibility of future performance and identifying likely operational issues. They can also be used to test the robustness of the plan with respect to performance variability and response to disturbances. Following identification of issues, simulation models can also be used for evaluating mitigation measures, through automated testing of alternative plans. Integration of mine data feeds with simulation and optimisation tools enables automated optimal responses to variations between the quarterly mine plan and actuals to be tested prior to release of and execution plan and implementation. The use of simulation and optimisation in weekly mine planning will be discussed in this paper with reference to surface mining examples.

Jun 25, 2023

Iron removal using biologically produced organic acids was investigated as a treatment option for the production of refractory grade bauxite. A leaching solution containing 98mM oxalic and 67mM citric acid was prepared from a sucrose medium using for fermentation the fungus Aspergillus niger. The leaching capacity of the metabolic product was tested on a bauxite sample containing 16-19% iron (as Fe2O3). Aerobic and anaerobic leaching tests were carried out at pH 3, 50°C and in the absence of light. Results indicated that more than 80% of total Fe can be removed from the ore, when the sample is finely ground and applying a two stage treatment. The presence of oxygen was seen to affect adversely the kinetics of the process, suggesting that leaching follows a reductive mechanism. Experiments that were carried out with different particle size fractions indicated that for obtaining efficient removal of iron particles should be finer than 0.63mm. Reduction of the operating temperature from 50 to 30°C caused a decrease in the rate of iron removal by more than 10 times.

Jan 1, 2006