Search Documents

By W. A. Rickelton, A. J. Robertson

The ability of triisobutylphosphine sulfides to selectively recover silver from acidic sulfate solutions containing zinc and copper is described. Selectivity is explained in terms of the concept of hard and son Lewis acids and bases. Silver is stripped from the solvent using a novel strip feed (thiosulfate salt), and the recovery of metallic silver from the strip liquor by electrolysis or cementation is suggested. The high selectivity of extraction for silver and the utility of the stripping reagent are demonstrated in continuous, countercurrent, mini-plant tests. Important reagent properties, such as hydrolytic stability and low aqueous solubility, are discussed.

Jan 1, 1988

By Gene E. McClelland, Dirk J. A. van Zyl

5.1 INTRODUCTION Heap leach cyanidation techniques possess considerable potential for exploitation of low-grade ores, small ore bodies, mine strip waste and tailing materials where fine grinding is not necessary for good extraction. For heap leaching to be successfu1, ore must exhibit certain characteristics, as previously discussed in Chapter 1. Primary among the necessary ore characteristics is that the ore must have good permeability after being crushed or treated and stacked into heaps if uniform distribution of the cyanide leach solution is to be achieved. Gold and silver ores containing excessive amounts of clays or fines generated by crushing are some of the most difficult to treat successfully by heap leaching. The presence of excessive amounts of slimes (generally classified as minus 50-micron or 270 Tyler mesh sieve size particles) in the heap leach feed will slow the percolation flow of the leach solution, cause channeling, or produce dormant or unleached areas within the heap. This may result in unreasonably long leaching periods and poor extractions. In extreme cases, the clays or slimes can completely seal the ore heap, causing the leach solution to run off the sides of the heap rather than to penetrate the ore heap. The problem of heap leaching ores containing fines can be aggravated during stacking and preparation of the ore heaps, because natural sorting of coarse and fine material occurs during these steps (Johanson, 1978). This phenomenon results in a concentration of ore fines at the center of individual ore piles and a concomitant concentration of larger rock fragments on the lower slopes and base of the piles. When the individual piles within the heap are leveled off prior to installation of the sprinkling system which delivers the leach solution, additional segregation occurs as the fines sift through the coarser ore particles. The segregation results in localized areas or zones with marked differences in permeability. As a consequence, the leach solutions follow the path of least resistance, percolating downward through the coarse ore regions and bypassing or barely wetting areas that contain large amounts of fines or slimes. Effective utilization of marginal gold and silver resources through heap leach processing requires the development of new methods in order to achieve more uniform size distribution during ore heap preparation and better slime control during leaching.

Jan 1, 1988

By Lester E. Sutton

The past three years have been the most difficult period in the modem history of the barge line industry. Having withstood the fuel cost run ups of the late 1970s and the imposition of inland waterways system user fees, the industry has struggled more recently with an overcapacity problem of unprecedented proportions. In responding to these challenges, the industry is undergoing important long-term structural changes, with the various individual barge lines pursuing an array of divergent long-term business strategies. This paper discusses these strategies in terms of their probable impact on the industry as a whole, and argues for the survival of a competitive number of large, national, independent barge lines as the outcome most in keeping with the long-term interests of the mining and minerals industry.

Jan 1, 1986

By William A. Turcotte

Introduction The need for water is fundamental to every minerals processing operation. Though this may sound rather elementary, it is one area that cannot be over- looked. Frank C. Quinn in his paper entitled "Water Is Water Is Water" (1967) said, "but it isn't as simple as that. Very often research is slowed down and production is hampered because of a lack of appreciation for the behavior of water." The quantity of water needed for any operation is determined from bench and pilot plant testing. The quality required by the process for both fresh and reuse water is also established during these two testing phases. Quinn's statements are true whether the process involves the paper industry, the minerals industry, or any other industry. It is not the author's intent to cover water quality, quantity, or re- cycle in specific terms, but to provide the reader with a general outline of the topic with reference to several valuable sources of information. The first part of the chapter will cover several of the areas that have been de- tailed by others and also provide a list of reference sources. The references at the end of the chapter are not all inclusive but will provide a good starting point. In the second part of the chapter, a detailed description, with flowsheet illustrations, is pro- vided on the evolution of the reclaim (reuse) water system at the Tilden concentrator. Mineral Industry Water Needs Beresford and Edler (1978) surmnarized the minerals industry's need for water this way: "minerals are necessary to a modern complex technological society. The minerals industry, while its water needs are relatively minor compared to large users such as agriculture, nevertheless requires a large quantity of water to carry out daily operations from mining to final product refining." In 1973 total water use in the United States was estimated at 15.14 billion cubic meters (4 trillion gallons) for the minerals industry. Of this, about 69% was recirculated within the system. In 1982 Watt and Horton stated that the percent of recycled water in the minerals industry had improved to 73%, showing the minerals industry is an efficient user of water and that steady improvement in water recycling is something the minerals industry can look to with pride. The percent of water needed by the United States' minerals industry was estimated in 1962 to be about 2% of the total water required by industry

Jan 1, 1986

By Makoto Terada

The most important consideration in planning the plugging and sealing of a mine for mine water control is to predict the water flow from the mine. For this purpose, a method of numerical analysis on the water behavior in the ground at the concerned mine area was developed and the mine water flows were simulated. A hydrological survey at the surface of the mine determined the recharge rate of ground- water and the apparent permeability of ground.

Jan 1, 1982

By C Rutter, N Shea, K Kolobe

The Henderson mine, a panel cave mine in Colorado, has undergone multiple ventilation system changes to meet dynamic airflow needs. This paper explains the ventilation designs for different production panels, the challenges faced, and the modifications made to optimize the ventilation systems. The study highlights the importance of a robust ventilation system for safe and productive mining.

Mar 2, 2022

By Henry N. Doyle

One can hardly discuss coal pneumoconiosis unless it is placed in the context of the total pneumoconiosis problem in the mining industry. However, it might be well if first we defined a few terms, since it has been my experience that the use of the word pneumoconiosis frequently causes con- fusion among those who are not familiar with the term. Pneumoconiosis comes from two Greek words meaning lung and dust. Hence, the word pneumoconiosis simply means dusty lung, or dust on the lung. There are many forms of the disease, some of which are disabling and some are not. Among the many dusts which cause pneumoconiosis might be included silica, asbestos, coal, talc, iron ore, and many other mineral dusts. Silicosis is a specific form of pneumoconiosis. It is caused by the inhalation of excessive amounts of silicon dioxide in the form of crystalline quartz. The disease is manifested by nodulation of the lungs which is apparent on an X-ray film. Continued exposure to silicon dioxide causes the nodules to grow and ultimately large areas of the lung become scar tissue which pre- vents the lung from performing its physiologic function. In its more advanced stages, there is a significant loss of pulmonary function which accounts for

Jan 1, 1966

By M. C. Tippett

The modern era of mineral exploration in Panama began in the late 1960's, resulting in porphyry copper discoveries at Petaquilla, Rio Pito, and Cerro Colorado. In contrast, Panama's early mining history (1503 to the early 1700's) was associated with gold. A single mine, Cana, in Darien Province, produced more than one Million ounces of gold in the colonial period. Except for episodic exploration activity by British and French interests, Panama's gold potential since the 1700's has been largely ignored.

Jan 1, 1989

By M. Tapper

If one considers that prehistoric man's first house may have been a limestone cave, calcium carbonate may be the most timeless of all building materials. Fanciful history aside, CaCO3 has been used for countless applications in human habitats. After all, tine marble block and tiles have always been the hallmark of eloquents and style. Mortars and cements derived from limestone have held together the very blocks of our civilization. In modem times, synthetic polymers are blended with ground limestone to produce everything from pipe, floor tile, cultured marble and house siding. All of these miracles of our technology contain CacO3 of various sizes and in varying amounts. This paper will discuss some of the critical attributes of CaCO3 which make it suitable for the new building products that have helped increase our standard of living. The vehicle of discussion will be a residential, single family house.

Jan 1, 1993

By C. W. Schultz

The distribution of material passing a screen, or a set of screens, is described by the equation [ ] where p = the probability that a single particle will pass the screen on a single presentation k = number of layers of screen cloth n = distance from head of screen expressed as number of screen openings. This model can be used to predict the performance of conventional screening operations (i.e., k = 1) as well as the so-called "statistical screening" operations. Using this technique, in which multiple identical layers of screen cloth are employed, screening can be carried out at a finer size than is possible with conventional techniques with no loss of separation efficiency.

Jan 1, 1969

By Michel Grenier, Gopal Kunchur, Stephen Hardcastle

This paper presents the findings of a dust study in a typical fluorspar processing plant. The primary purpose of this study was to identify employees and occupational groups exposed to high dust levels and determine compliance with personnel regulations for regular and extended work shifts. The range of airborne concentration of respirable silica and fluoride compounds in specific areas and on personnel was determined. State of the art dust monitoring equipment and tracer gas techniques were used to measure dust concentration, pinpoint dust sources and map major airflow trends in the mill. Results of the survey indicated silica dust concentrations in excess of permissible limits being produced mainly by crushers at the south end of the building. Tracer gas releases and gas chromatographic analysis further showed that prevailing south to north air currents tended to carry and spread dust produced by the crushing operations throughout the process plant. Airborne concentrations of fluoride compounds measured during the study were always well below the prescribed threshold limit value (TLV) for the contaminant. Recommendations, including a mechanical exhaust ventilation system on crushers and transfer points, scheduled preventive maintenance on existing bar sprays and wearing of personal protective equipment were made which significantly improved the work environment. Further testing conducted after Installation of the dust extraction system revealed significant improvements in most areas of the mill.

Jan 1, 1991

By D. Hulse

Mineral resource classification is described in both the SME and CIM Standards for Mineral Resource Reporting. The CIM Standard states “… sampling … is sufficient to assume geological and grade or quality continuity between points of observation”, thus is a function of continuity and sample spacing. Continuity can be measured by use of a variogram model, but average sample spacing in three dimensions is more difficult to measure. The declustering algorithms provided with Geostatistics software, are commonly used to weight data for statistical analysis due to the sometimes-irregular spacing between drill holes during exploration. The weights are lower when data is closer, reflecting shared influence between samples, and higher for isolated samples reflecting independence. This paper will discuss the potential to use estimates of the declustering weight as an inverse relative measure for average sample spacing to gauge the confidence of the estimate independent of the single nearest sample. PROBLEM The classification of mineral resources and reserves has long been a combination of science, past experience of the estimator, judgment, and feeling. All of the definitions as presented in the standards of the various countries that participate in CRIRSCO are similar and deal with “sample points sufficiently closely spaced to support confidence in the continuity of …” This has been interpreted as the distance between the block estimated and the nearest sample (or samples). Geostatistics gave us the calculation of the estimation variance of the block, an implicit part of the calculation of weights in Kriging, to account for the confidence in the estimate. More recently, “Kriging Efficiency” has been used, however it is still dependent on the estimation error and responds in a similar fashion to the distance to the closest sample. It is also sensitive to the variogram nugget. Many of these methods result in very low distance/high confidence measures for blocks adjacent to a sample point with confidence decreasing (sometimes rapidly) as the distance to one nearest sample increases. This results in the “spotted dog” phenomenon where individual samples are surrounded by a higher classification near each sample decaying into pattern of decreasing confidence halos. In addition to the visual image of the spots, this raises the more practical problem of mine design when the classification changes between measured, indicated and inferred. This has led to ad hoc methods to classify material within the mining block so all of the stope receives that classification. These manual methods re both labor intensive and subjective. A popular technique is a multiple search method, where the estimator defines a minimum of number of samples from a minimum number of holes within a nested set of search distance that are used to classify estimates. These specified set of increasing distances are usually proportional to the variogram range. While this is generally a good technique and overcomes the spottiness of the closest sample or kriging error, it has certain issues including:

Jan 1, 2019

By Malcolm Reeves

The heavy oil reservoirs of Alberta and Saskatchewan include sequences of unconeolidated silts and fine sands which respond in an unusual manner when subjected to the high temperature and pore-fluid-pressure associated with steam injection and other thermal enhanced recovery techniques. Apparent transient connections are suddenly established between producers and injectore and there is an associated enhancement in oil (and sand) production. These phenomena have been attributed to local fluidization and piping processes which are known to occur in situations where high pore-fluid-pressures prevent the mobilization of intergranular friction. These breakdown processes may be associated with the penetration of tongues of the heated reservoir fluids with suspended sand into the creep sensitive intact reservoir since the viscosity ratios are sufficiently high for viscous fingering instability of the fluid-fluid interface. A program of laboratory tests has been carried out to measure the strength characteristic of saturated oil sands at a variety of temperatures and fluid pressures. These tests suggest, that in common with the coarser Athabasca sands, the Waseca sands have very little cohesive strength and show the characteristic dilational failure response of dense sands. Some special tests, devised to determine the relative ease with which samples can be fluidized, confirm the expected susceptibility of the fine- sand silts. Both piping and fluidization can be readily induced at in-situ reservoir temperatures and pressures. Analysis of stresses around wellbores suggests that fluid-pressure gradients may be sufficient to initiate piping and that backward erosion along streamlines may link producers and injectors. Such pipes may act as well “adits” gathering oil from the heated reservoir and contributing to enhanced production rates. Mechanical breakdown of the reservoir by drilling, injection and production processes provides a consistent possible explanation for the sand-cut response of production wells.

Jan 1, 1986

By Tugba Kami?oglu

Hydromagnesite (Mg5(CO3).(OH)2.4H20), one of the sedimentary deposits in Salda Lake Basin, is developed under the control of active tectonics regime. Since the occurrence and deposition mechanism of hydromagnesite are unstable under atmospheric conditions, in order to evaluate the precipitation process, systematic host rock, lake water (surface, 20m, 40m, 60m) and hydromagnesite sampling were carried out. Macro, micro, XRD and chemical investigations were done in detail. Not only the results and formation and crystallization mechanism but also hydromagnesite's St values were evaluated. Main resources could be ultramaficmafic surrounding rocks for hydromagnesite formations. However, hydromagnesite development is considered in different phases, because it has showed various characteristics in Kayadibi and Köpekcayin areas. In Kayadibi area Huntide-Dolomite-Aragonite-Hydromagnesite paragenesis has been realized. Hydromagnesite has also formed in Köpekcayiri area, large amount of hyrdomagnesite occurrences and levels various are noticeable. Actual position of hydromagresite levels exhibits tectonic influences in and around the lake. Therefore, the levels seems to exhibit secondary formation properties. In addition, the formations are being still maintained sedimentation as products of a peripheral deposition phases. Resolving and redifferentiation sedimentation processes probably improve in periods of lake water chemistry especially Ca/Mg proportional changes, and also SI variations indicate the mentioned precipitation mechanism. Similarly, side and into the lake hydromagnesite is stored different levels and ultramafics-mafics rocks fallow indicated stages. It is postulated that hydromagnesite formation, which is existed by result of determined developments and multiphase sedimentation, could be originated from probable crack zones on the lake bottom.

Jan 1, 2005

By André Vervoort

The roof behaviour in room and pillar panels during the development of roadways and the subsequent pillar extraction was monitored underground and numerical simulations were conducted. For several underground sites, a satisfactory, correlation was found between underground measurements and three-dimensional numerical simulations using a boundary element code in the linear elastic domain. However, to simulate bed separation, and roof block collapses more complex models were required, of which examples are presented.

Jan 1, 1992

It is widely accepted that particles stabilize flotation froths and that stable froths result in improved flotation performance. Predicting the effect of particle addition on froth stability is, however, challenging. Furthermore, there is currently no technique that allows the prediction of the effect of different flotation reagents on froth stability, without carrying out froth stability experiments.

By A. M. Laird

Endako Mines' molybdenum operation is located near the geographic center of the province of British Columbia, Canada. The property is six miles south of the Northern Transprovincial Highway and the northern main line of the Canadian National Railway. The area is broken by high hills covered with dense stands of spruce and pine with vast areas of the valley floors covered with aspen and poplar. The climate is moderate with precipitation averaging 22 inches per year. Approximately four feet of snow accumulates in the winter, and temperatures range from 900 F. in summer to -40° F. in winter. The orebody, a lowgrade porphyry type deposit, occurs in a widespread granitic intrusive which has been locally weakened at the intersection of two regional faults. In this vicinity the quartz monzonite has been further shattered to permit the entry of mineralizing solutions and local dykes. Two types of mineralization occur within the orebody. The most prom¬inent is the six inch to four foot wide continuous quartz veins with characteristic ribbons of molybdenite and frequently finely-divided grains of molybdenite within the quartz. The second type occurs as fine fractures filled with quartz molybdenite in the form of a stockwork halo radiating out from 20 to 200 feet from the quartz veins. Minor hematite, magnetite and chalcopyrite are also present. Mineralization is roughly proportional to the extent of kaolinization in the quartz monzonite, kaolinization being one of three distinct forms of hydrothermal alteration. Pyrite is commonly associated with molybdenum mineralization within the orebody and a pyrite halo is recognized on the south side of the orebody.

Jan 1, 1968

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence induced by underground coal mining activities, especially longwall mining operations, can cause various problems to interstate highways ranging from structural integrity to drivability to safety. Accurate subsidence prediction, correct influence assessments and effective mitigation measures are the keys to ensuring the safety of highway traffic. The surface subsidence prediction program, called comprehensive and integrated subsidence prediction model (CISPM), was developed based on the principle of influence function method and has been validated with a large number of subsidence measurements. In this paper, the techniques to use the predicted final surface movements and deformations for assessing their influence on the integrity and functionality of highway structures — such as road surface pavements, concrete slabs and transverse joints — vehicle dynamics, comfort level and drivability are presented. A number of mitigation measures to protect the highway structures and to ensure traffic safety are proposed, along with an application case.

By A. J. Neale

Much has been published lately about the application of advanced control strategies in the automatic control of autogenous and semi-autogenous grinding circuits. The application of adaptive control algorithms, self-tuning controllers, state estimation, and expert systems has been well documented. While these approaches can be very effective; experience has shown that quite often simply "fixing the fundamentals" can have a significant positive impact on overall grinding circuit performance. This paper will highlight the results of process optimization and process control work by the authors at a variety of autogenous and semi-autogenous installations. A review of one approach for quantifying the mill load/bearing pressure/power relationship is provided. Accurate monitoring of key mill process variables is a necessary prerequisite for both effective process analysis and process control. This paper discusses some of the concerns related to defining steady state operating conditions and the issues related to signal conditioning. The paper concludes with a discussion of an effective application of algorithmic constraint control which incorporates many of these considerations.

Jan 1, 1994

Mill #4 processes mildly refractory ore from Carlin Trend deposits. Diagnostic analysis of plant operating data was used to generate a mathematical model containing the key parameters influencing the gold recovery. The model was used to direct modifications to plant operating practice. The cyanide dosing strategy was changed to reduce preg-rob gold masses and cut reagent consumption A finer grind was achieved without capital investment. The density in CIL was lowered, and tighter control was exercised over plant throughput. These changes resulted in a recovery increase of at least 2%, worth $111,000/month at $300/oz, and concomitant reagent cost savings of $55,000/month.

Jan 1, 1999