Search Documents

By R. P. King

Direct observations of intergranular fracture during comminution are very difficult to make. The best indirect method is based on the measurement of interphase area before and after comminution. If intergranular fracture does not occur, the interphase area should be conserved during comminution, but it should decrease if significant amounts of intergranular fracture occur. The interphase area per unit volume can be determined by image analysis from measurements on sections of the unbroken ore and on sections through the particles after comminution. However, the measurements must be corrected for the effects of image resolution on the measured phase and particle perimeters. A correction procedure was developed, and the true interphase perimeter per unit volume was measured before and after comminution in a sample of chromite-serpentinite ore and two samples of Witwatersrand pyritic quartzite. The pyritic quartzite showed no significant evidence of grain- boundary fracture while the chromite-serpentinite showed a significant decrease in interphase area per unit volume of chromite, indicating that intergranular fracture occurred.

Jan 1, 1992

By Erhard M. Winkler

The rapid decay and disfiguring of stone monuments in urban and desert rural areas has challenged conservators to protect stone surfaces from premature decay. They attempt to halt the natural process of stone decay and possibly to restore the original strength lost mostly by chemical weathering and the loss of binding cement. Ageneral solution is not possible because the physical and chemical characteristics must be considered for different stone types. The failures of stone preservation and restoration are greater in number than the cures. The need for repair of stone decay goes back to evidence of Roman replacement of decaying stone. The presence of excess water in buildings has long been recognized. Moisture tends to enter masonry from air in humid climates, a most important but often underrated factor (Fig. 1) suggesting that sealing should be the answer. Undesirable staining and efflorescence result in accelerated scaling. Today, the great variety of chemicals available to the modem conservator for sealing. consolidating, or hardening stone fall into two very different categories: surface sealers and penetrating stone consolidants, or a combination of both. SEALERS Sealers develop a tight, impervious skin which prevents access of moisture. Surface sealing has saved monuments from decay by eliminating the access of atmospheric humidity. Pressure tends to develop behind the stone surface by moisture escape. Efflorescence, crystal growth action, and freezing can cause considerable spalling (Anderegg, 1949). Flaking results when moisture is trapped behind the sealed surface. Yellowing and blotchiness are also frequently observed. The following sealants are in common use today: linseed oil, paraffin, silicone, urethane, acrylate, and animal blood on stone and adobe. Extensive cracking and yellowing has resulted soon after application. In the past many such treatments have created more problems than cures: 1. Linseed oil and paraffin have been in use for centuries. Embrittlement and yellowing occur rapidly because these are readily attacked by solar ultraviolet radiation. 2. Animal blood as paint has temporarily waterproofed adobe mud and stone masonry. The origin of blood paint has a religious background rooted in the Phoenician and Hebrew cultures. Instant water soluble dried blood can substitute for fresh blood. Winkler (1956) described the history and technique of the use of blood. 3. Silicones have proven very effective and are long lasting. In contrast, acrylates, urethane, and styrene are generally rapidly attacked by UV radiation (Clark et al., 1975). Sealing of Different Rock Types Granitic rocks have a natural porosity traced to 4.5% contraction of quartz, during cooling of the parent magma, compared with only 2% contraction of all other minerals; protection against the hygric forces may require waterproofing of granite in some in- stances. The Egyptian granite obelisk in London is an example. Soon after its relocation from Egypt to London, Cleopatra's Needle was treated, in 1879, with a mixture of Damar resin and wax dissolved in clear petroleum spirit; surface scaling became evident after half a year of exposure to the humid London atmosphere. The treatment of the ancient granite monument from Egypt has denied access of high relative humidity (RH) in London to the trapped salts inherited from the Egyptian desert and has protected the monument from decay (Burgess and Schaffer, 1952). The sister obelisk set up in Central Park, New York City, has fared less favorably because similar treatment was done too late, only after the salts hydrated and hundreds of kilograms of scalings disfigured the obelisk surface (Winkler, 1980). Surface coating of other common stones may be needed. Crystalline marble absorbs moisture from high RH atmospheres: dilation may ensue when curtain panels bow as the moisture starts to expand during daily heating-cooling cycles. A good sealer may prevent the moisture influx provided that no moisture can enter from the inside of the building. Limestones, dolomites and all carbonate rocks are subject to dissolution attack by rainwater, especially in areas where acid rain prevails (Fig. 2). The interaction of sulfates in the atmosphere with the stone can be halted by waterproofing to avoid the formation of soft and more soluble gypsum. The stone surface attack can be diminished if nearly insoluble Ca-sulfite crusts can form, instead of Ca-sulfate. Replacement of fluorite or barium compounds at the stone surface acts as a hardener, rather than a sealant. Sandstones have generally high porosity and rapid water travel can occur along unexpected routes and from any direction. Any surface sealing may do more damage by scaling and bursting than if the stone is left without treatment. Sealing of sandstones is therefore not advised at any time. Testing the efficiency of sealants: Several authors discuss waterproofing materials, silicones, urethanes, acrylates and stearates, as to their water absorption, spreading rates of water on the treated surface, water vapor transmission, resistance to efflorescence, and general appearance (Clark et al., 1975). De Castro (1983) measured the angle of contact of a microdrop (0.004 cm3) on a stone surface as characteristic of the wettability. Laboratory tests and limited field performance are described by Heiman (1981). The crest of a Gothic sandstone arch, which was sealed with silicone,

Jan 1, 1994

By R. H. Sailors

During the last 15 years, the North American Mining Industry has experienced increasing usage of cast high chromium white iron grinding media in wet grinding applications. First introduced into the cement industry (klinker grinding) where wear rate reductions of four or five times have been realized compared to steel balls, this same grinding media serve the iron, copper, and phosphate markets by resisting not only impacts and abrasion, but also corrosion which occurs in wet grinding. In these markets, single mills containing 250,000 kg of grinding balls are not un-common and hence the economic potential with respect to lower wear rates can be significant. Add to reduced wear rate the increased production efficiency that is possible and it is readily understood why much of the mining industry uses cast high chromium grinding media. Metallurgically, the alloys used consist of a martensitic matrix containing hard M7C3 eutectic carbides. Carbon (2.0 to 3.5%) and chromium (12 to 277.) are characteristically used to arrive at the desired properties.

Jan 1, 1989

By William J. Ferguson

At Henderson Operations the 24-kilometer conveyor system consists of three main conveyors with lengths of 1.2 km, 16.7 km and 6 km. Upon commissioning of the conveyor system, the Henderson maintenance department was challenged with the inspection and monitoring of over 50,000 idlers. To take a proactive approach to idler maintenance, an idler tracking database system was developed. Using the idler tracking program, the Henderson Crush & Convey department now has the ability to provide data for engineering solutions to idler problems and to manage thousands of idlers for priority replacement work and warranty purposes. Recognizing the potential for injury to Henderson employees in the process of idler handling, Henderson approached idler replacement as a material handling process. Material handling solutions have resulted in failed idlers being replaced and discarded from the underground environment without ever touching a human hand. This paper will detail how Henderson tracks idlers in all primary conveyor belts and how an innovative idler handling system can result in reduced risks to conveyor maintenance employees.

Jan 1, 2004

By R. Brough, T. K. Moller

There are differences in design aspects between steel and rubber linings in grinding mills. This paper describes the basic design rules for rubber liners for different grinding applications. When converting a mill from steel to rubber liners, the design must be changed from such familiar steel liner shapes as wedge bars and plates, wave liners, and ship-lap, to take advantage of the characteristics of rubber. Very little of the knowledge of the wear properties of steel can be used for the design of rubber mill liners.

Jan 1, 1990

By Hassan Madani

Kushk lead-zinc mine is located in central part of IRAN. The mine is owned by Bafgh Mines Co., which is a nationalized company. Exploration results show that ore occurs in the area that extends for 800m length and 180m depth. The approved, probable and possible reserves of the mine is 900,000 tons, 1,120,000, tons and 1,450,000 tons respectively with average grade of 17.7% zinc and 4.3% lead. The total annual output of the mine all was by underground mining, is in the order of 100. 000 tons. The main entry to the mine is via an inclined shaft with a cross-sectional arp of 8 m2, length of 263m which dips at 20°. The ore is mined mostly by sublevel stopinq method. The major difficulty in ventilating the mine was that related to spontaneous combustion of pyrite, which was more serious in some parts of the mine than others. In order to reduce this risk, a new ventilation system for the mine was designed, using 4 exhusting fans.

Jan 1, 1991

By Thomas E. Howard

Engineers today face a tremendous challenge. Growing population and rising standards of living all over the world are creating unprecedented and accelerating demands on and for all kinds of technology. At the same time, the public is becoming more and more conscious of--and concerned with--the impact of technology on human welfare. The growing controversy over the Supersonic Transport is a case in point, It is clear that the modern engineer must expect to spend a growing share of his time considering this dilemma and evaluating the tools that are available to him, not only with respect to their adequacy for the job at hand but also their capability for meeting the increasingly demanding--and, in many cases, conflicting--requirements of the future. This meeting seems a particularly appropriate place to speculate about the future of mining technology. The summary of the state-of-the-art in surface mining contained in the papers scheduled for the International Conference, together with the recently published Surface Mining volume, constitute not only a major contribution to the technical literature but also form an impressive record of technologic progress. That record, and the advanced technology displayed in the exhibits, and to be discussed in the SME technical sessions demonstrate engineering achievement in which the mining community can justly take pride.

Jan 1, 1968

By L. D. Gehi, A. W. Khair, M. Ahmad

This paper presents an analysis of the dynamics of bit wear on the productivity of continuous miners. Two field surveys were carried out. The first survey assessed the impact of bit wear on productivity and production cost. The second survey studied the wear characteristics of the cutting tool (i.e., magnitude, forms, and mechanisms of bit wear, Primary factors affecting bit wear were identified. Laboratory experiments were carried out to study in detail the effect of some of these primary factors on wear. Results indicate, that bit wear has a significant effect on the productivity a continuous miners. Furthermore, under severe geologic conditions (i.e. cutting rock partings in roof and floor) bit wear not only hampers the productivity, but also increase the production cost due to a higher consumption of bits. This study also indicated that beyond 20% of the conical height loss (which corresponds to 7% of the weight loss) the rate a bit wear accelerates. This increased rate of wear is an indication of higher abrasion between bit body and cutting material, resulting in a dustier environment.

Jan 1, 1995

By W. S. Versluis, G. W. R. Kuzyk

Atomic Energy of Canada, Ltd. (AECL) is constructing an Underground Research Laboratory (URL), a major component of-the Canadian Nuclear Fuel Waste Management Program. In July 1988. AECL and the US Department of Energy commenced a cooperative research program that included extending the URL shaft by 190 m (623 ft) to the 443-m (1,453 ft) depth. The shaft extension, 4.6-m- diam (15-ft-diam), was excavated by full-face blasting using a burn cut. A Galloway stage accommodated the research activities and the sinking contractor's requirements. Blast designs incorporated controlled blasting techniques to minimize blast-induced damage on the shaft walls. The full-face method has been very effective, with 3.5-m (11.5-ft) rounds being advanced.

Jan 1, 1990

By M. Kane, O&apos

BHP Iron Ore initiated research programs in January of 1995 to develop long term plans for decommissioning of the waste rock material at their Mt. Whaleback operation. More than 2 billion tonnes of waste rock were deposited during the past 30 years. Ultimately, the operators will deposit a total of approximately 5 billion tonnes in waste rock dumps constructed near the open pit. The Mt. Whaleback operation is located in a semi-arid climate adjacent to Newman, Western Australia, approximately 1200km north-northeast of Perth, Western Australia. The primary research program includes the development of technology for the long term performance of the waste rock dumps with respect to vegetation, slope stability, surface runoff, erosion, and water infiltration. This paper focuses on the design and implementation of a cover system to prevent water infiltration to the underlying waste rock. A laboratory program and the soil-atmosphere modelling completed to design the horizontal field test plots are described. The construction of the horizontal surface field test plots are discussed together with the field instruments installed to monitor performance. The key components of the instrumentation program are the design and installation of large scale field lysimeters to measure the unsaturated flow of moisture into the waste rock from the base of the cover layer. The cover system is designed to maximize infiltration during wet periods for subsequent evapo-transpiration while minimizing surface runoff. The result is a near zero net infiltration to the underlying waste material. A key feature of the design is the use of pit run waste material as the cover material. Monitoring is in progress and will continue for at least two annual wet/dry cycles. The optimum cover system should minimize the net infiltration of water to the underlying waste rock while maintaining physical and ecological integrity for long term performance.

Jan 1, 1998

By Steven L. Webb

In 1965, Monsanto started planning of a new dike (No. 15) for use in disposing of ore tailings at its Columbia, Tennessee phosphorus plant. Generally, in the phosphorus industry only clay tailings are produced making it necessary to borrow fill for construction of a retaining dike. Borrow area investigations indicated that weathered shales and limestones adjacent to the dam site would provide adequate construction materials. It was proposed that the more clayey weathered shales would be used for the impervious core and the more granular weathered limestones would be placed in the outer shell of the dike. A dike section is shown in Figure 1 with gradation curves for core and shell materials in Figure 2. Figure 3 shows an aerial view of the tailings pond and dike during first-stage construction. Although the borrow area explorations indicated that the weathering of the sedimen-tary deposits was highly irregular, it was not considered necessary, at the time, to specify special excavation techniques that would ensure a thorough blending of the materials in the borrow pit. Instead, because of the short haul distance, a scraper operation for both clay core and granular shell materials was adopted as the most economical construction method. Using this materials-handling technique, variations in permeability could be expected in the compacted layers inthe embankment. Where continuous layers of less clayey limestones were placed in the core of the dam, extending from the upstream to downstream shells, seepage losses would be expected to increase substantially. Upon completion of the damn 1966, and shortly after reservoir filling, it was apparent that the construction technique used had resulted in the formation of pervious layers through the clay core. Excessive seepage on the downstream face of the dike was noticeable within a very short time. A monitoring program was established, using piezometric observations and flow measurements. These data indicated that seepage should be reduced and the application of an asphaltic emulsion

Jan 1, 1971

By Gregory E. Korbin

The effectiveness of pre-reinforcement as an immediate stabilization measure as well as its contribution to the permanent stabilization of a tunnel were studied through the use of physical (Figure 1) and numerical models (1). Physical models were designed for the investigation of two pre-reinforcement systems: first, reinforcing far ahead of the main excavation (Figure 2); second, spiling reinforcement ahead of the face (Figure 3). In both cases, the use of reinforcement was responsible for permanently stabilizing an otherwise unstable opening. Data from the physical models were used to calibrate a numerical model from which additional information on long term behavior, methods to account for the capacity of a pre-reinforcement system, and the mechanisms involved were ascertained. These studies indicated that pre-reinforcement can stabilize a rock mass effectively as it reduces deformations and thereby deterioration due to strain softening, provides rock mass confinement leading to increased available strength, and maintains rock arch continuity allowing for increased tangential stress in the immediate vicinity of the opening. Field studies verified the capacity of spiling reinforcement to restrain initial deformations.

Jan 1, 1976

By Ch. R. V. S. Nagesh, Ramesh Naidu Mandapati, Venkata Swamy Nalajala, Tondepu Subbaiah, Naga Jyothi Kothamasu

Leaching studies of magnesite obtained from Tamilnadu Magnesite Limited, Salem, have been carried out using hydrochloric acid leaching and percentage of magnesium chloride recovered was estimated. The variables considered in this study were the following: duration of leaching, volume percentage of hydrochloric acid, temperature, and pulp density. Percentage recovery of magnesium chloride increased with duration of the leaching, volume % of concentrated hydrochloric acid, and temperature. Percentage recovery of magnesium chloride decreased with increase of pulp density. The optimum conditions found to be pulp density (10%), hydrochloric acid concentration (30%), duration of leaching (2 h), and temperature (348.15 K). Iron was removed by treating the leach liquor with hydrogen peroxide and by raising the pH to 3.5–4. The purified leach liquor was subjected to spray drying for producing high pure magnesium chloride.

Jun 7, 2022

By CORA ROELOFS

While the COVID-19 pandemic has dominated the headlines, another epidemic in the United States has continued apace — the opioid epidemic. Half a million opioid overdose deaths have occurred in the United States since 1999, when the opioid epidemic began. The causes of the epidemic include the rise in prescriptions for opioid pain medications, including for work-related pain. Miners and other occupations identified as physically demanding and at higher injury risk have been found to be at increased risk for opioid overdose [1]. However, awareness of the risk factors that might lead to opioid use, the potential hazards associated with their use, and resources to prevent addiction and death can allow miners to make choices that can reduce these risks.

By Claudia Castillo, Katja Freitag, Jan Cilliers, Diana Drinkwater, Robert Seitz

The talent gap in mining is not a new challenge. Mining companies continue to seek innovative ways to attract, develop and retain talent, and younger workers are looking for opportunities to develop their professional careers. Training provides a key value proposition for both employees and employers as it helps build a talent pipeline while offering opportunities for learning and growth and value creation. In 2020, Metcelerate launched its 20-month program for early career mineral processing engineers. The program helps develop critical technical skills in the workplace and is a tool to identify motivated engineers and change culture within teams. Learners cap their skills development by executing a technical investigation. This generates immediate value—a win-win outcome for learner and company.

Feb 1, 2025

By David J. Hatem

Public-private partnerships (PPP) are gaining in popularity at the federal, state and local levels as the public sector seeks private capital to finance infrastructure and other projects that traditionally have been funded with public funds. In general, a PPP involves a development agreement between a public owner and a private sector concessionaire. Under the development agreement, the concessionaire is responsible for financing, designing, constructing and typically operating and maintaining the completed project for a concession period (often multi-decades in duration). The concessionaire typically enters into an agreement ? the design-build agreement ? with a design-builder to design and construct the project. The concessionaire may secure financing from banks, investors or from a combination of these and other sources (collectively the financier). While the PPP experience in the United States has been modest to date, an increasing number of projects involving tunneling or other significant subsurface work are already being delivered in the PPP mode. Public owners have significant options to address risk allocation for subsurface conditions on PPP projects. The same sound and fundamental principles of fairness in risk allocation that apply in other major subsurface projects should be applied and adopted in the PPP context

Mar 1, 2014

The 2014 George A. Fox Conference at the Graduate Center, City University of New York in New York City was presented under the theme, ?21st Century Challenges for the Tunneling Industry. Bruce Grewcock, chief executive officer and president of Peter Kiewit Sons? Inc., opened the conference with a keynote address in which he set the tone for the rest of the day by touching on the many challenges the industry is facing, which are plentiful and complex. Covering the breadth of the industry, he spoke about everything from the technical challenges that come from working beneath the streets of some of the most densely populated regions in the world to the challenges that come from working with the people who live in those areas. ?My observation is that we, as an industry, are being asked to put structures in places where they are needed, but are complex environments to work in,? said Grewcock. ?We work in an industry that relies on some of the most technically challenging engineering in the world, and when we are done with a project, we cover it up and no one ever sees it.? Despite these issues, Grewcock said that, in his opinion, the biggest challenge the industry is facing is that of people; more precisely, where to find the next batch of people. Looking out at the conference-record crowd of more than 400 registered attendees, Grewcock quipped that he saw plenty of gray beards and asked aloud, ?Where will we find, educate and train the people to tackle the issues that this industry will face in the future??

Mar 1, 2014

By E. Westman

Geographic Information Systems (GIS) are becoming a more commonly used tool for resource estimation as they provide not only a database management platform, but also the graphical capabilities to visualize resource characteristics. Interpolation methods used commonly in these resource studies do not typically provide a quantitative answer to the question: "How accurate is the estimate?" By comparing localized measurements at several locations to the interpolated thickness distribution used in a resource estimate, a quantitative analysis of accuracy can be obtained. The technique is demonstrated with a case study from Central Appalachia.

Jan 1, 1999

By R. W. Hutson

One of the fundamental precepts of experimentation is the isolation of a single variable to quantify its individual effect. Unfortunately, the variability of natural rock joints has frustrated such isolation. This variability and the high cost of securing a large member of natural joints has lead to increasing experimental dependence on stage shearing, artificial tension fractures and/or model materials. The new apparatus described herein allows for the first time replication of real joints with field scale asperities. It employs a diamond band-saw blade with computer controlled feed table to cut joints with high precision. The feed system is capable of placement to tolerances similar to those of a high quality computer plotter. The accompanying software allows the table to cut any desired joint shape (repeating or non-repeating) within certain, over-all size limitations. Resulting joint surface dimensions and roughness as well as shear resistance indicates that the joint surfaces are reproduced with a precision similar to that possible for the control of other experimental variables such as normal and shear forces.

Jan 1, 1986

By Sergey G. Pushkin, Eugeny L. Schastlivtsev, Anatoly A. Bykov

Three years ago the authors and a group of assistants began to develop a GIs-system for integration of comprehensive eco- logical information to be linked to geographical maps of Kuzbass region. And now we have got the working system and some first results that the present paper deals with.

Jan 1, 1996