Search Documents

By J. M. Wempen, R. D. WEYHER, M. K. McCarter

Beam theory is a proxy for the behavior of intact, deforming roof strata above underground openings. Strong, stiff, intact strata have the ability to store significant strain energy when underground openings have large spans, as is typical of longwall operations. When strata fail, they may release some or all of this strain energy. Released energy is partitioned between fracture, thermal and seismic energy. The tensile failure surface in simply supported beams is predicted to be free of shear stress. This prediction and the kinematic inability of crack slip during fracture make significant dissipation of energy by friction unlikely.  In this study, the failure energy partitioning of specimens from the Nugget Sandstone formation is examined. Tensile fractures in specimens were induced using three-point loading tests. Elastic waves emanating from fracture events were recorded using an array of accelerometers. Accelerometers were placed within two crack lengths of the fracture surface, and the acceleration records are similar to strong motion seismic records. Spectral analysis was performed and used to develop synthetic, well-behaved, acceleration signals. Synthetic velocity signals were used to estimate radiated seismic energy generated by fracture. These estimates of radiated seismic energy demonstrate a potential means to constrain the minimum seismic partition. Fracture testing was performed on additional samples to estimate the fracture toughness of the sandstone. Synthesis of this data demonstrates a potential means to constrain a maximum seismic partition. Bounding the seismic partition for this type of fracture event could aid the detection and evaluation of seismicity emanating from longwall operations. Having better information about the location and magnitude of mining induced seismicity within longwall overburdens could lead to better understanding of extraction sequencing and rock behavior in general. These energy estimates also support the hypothesis that dissipation of thermal energy by friction is small in bending tensile failure.

By S. D. Van Nort

Editor’s note: This is the first of two MINING ENGINEERING articles about the Grasberg deposit. The second, focusing on open pit mine development, will appear in the April issue of the magazine. The Grasberg porphyry copper-gold deposit of Freeport Indonesia Inc. lies within the Ertsberg Mineral District in central Irian Jaya, Indonesia. The Grasberg deposit was discovered during a drilling campaign initiated in the mid-1980s. Production at the open pit de- posit commenced in December 1989. The Grasberg copper-gold ore body is contained within a young igneous complex of dioritic composition that intrudes limestones of the Tertiary New Guinea Group. Alteration is typical of porphyry copper deposits worldwide except that higher grade primary chalcopyrite with significant gold values is associated with a centrally located zone of strong quartz stockwork. Irian Jaya comprises the western half of the island of New Guinea. The Ertsberg District lies 70 km (43 miles) inland from the Arafura Sea at an altitudeof3500 to45OOm (11,480to 14,764 ft). It straddles the Papuan fold belt. This belt forms the east-west trending chain of mountains that extend the entire length of New Guinea and is the site of numerous mineral districts.

Jan 1, 1991

By D. Gove

All mining operations using trucks have a common need to properly match the number and size of hauling units (trucks. wagons. scrapers. etc.) to a loading unit (wheel loader. hydraulic shovel/excavator, cable shovel. push tractor. etc.) to provide the best possible fleet match. Optimizing fleet match minimizes the cost per unit of material moved by that fleet. As haul conditions change (haul length. grade. or rolling resistance), there may be need to adjust the number of trucks to maintain the optimum fleet match. Fleet Production and Cost is a tool which, among other things, can be used to optimize the truck-loader match.

Jan 1, 1994

By Peter G. Chamberlain

Many mining engineers considering in-place leaching for the first time are uncertain as to how to evaluate ore bodies for potential leachability. Evidence presented in this report emphasizes the critical role of permeability in such evaluations. Whether an engineer is considering leaching "tight" formations typified by the porphyry copper deposits of the southwest or the permeable uraniferous sandstones of Texas and Wyoming, permeability measurements are the keystone of any testing program. Permeability tests range from cheap and easy to highly expensive and sophisticated operations. Constant head, variable head, and pumping tests all have application in evaluating ore bodies for in-place leaching. Costs of these tests will not unduly deflate the pocket- books of most mining companies. The basic procedures for selecting and running these field tests-including preparing suitable wells--are reviewed for the benefit of newcomers to in-place leaching.

Jan 1, 1979

By Walter P. Hansen

Belt conveyors offer a reliable means and often do the most economical job for providing continuous bulk material transport, whenever the terrain permits their installation. The ore processing, construction and mining industries use belt conveyors to carry all types of material, from small to large tonnages. Most of the conveyors Fluor Mining & Metals, Inc. designs for metallurgical plants are in the in-plant category, of limited length and medium tonnages, and use fabric carcass conveyor belting. Belt widths can range from 24 to 60 inches Generally, the layout and design of these belt conveyors present no unusual problems. However, calculations for belt tension and horsepower, design of materials transfers, and the sizings and layouts of belt pulley stations and their drives are time consuming.

Jan 1, 1979

By John A. Sievert

Sedimentary deposits contain an appreciable portion of the world's supply of uranium. Predictions of nuclear fuel usage in the United States indicate that these reserves will have to be tapped if the domestic industry is to be the major supplier of fuels for the nuclear reactors. Techniques developed within the petroleum industry are a base on which to build economically attractive fluid mining processes for the recovery of these uranium values. The problems central to the success of such mining processes are the containment, control, and recovery of a narrow band of pregnant leach solution as it progresses from the point of injection to the point of production Given sufficient incentive, suitable solutions to these problems can be found

Jan 1, 1970

By C. Y. Chen

Public Law 75-87, the Surface :mining Control and Reclamation Act of 1977 (SMCRA), Section 516(b) requires the underground coal mining operator to "adopt measures consistent with known technology in order to prevent subsidence causing material carnage to the extent technologically and economically feasible, maximize mine stability, and maintain the value and reasonably foreseeable use of such surface lands, except inn those instances where the mining technology used requires planned subsidence in a predictable and controlled manner . . .?. The Congress also directed the Secretary of the Interior to promulgate regulations to implement the law. As a result, the control of subsidence from underground coal mining to minimize surface damage has become the mandate of a Federal law. This paper discusses the mechanics of subsidence and the effects of subsidence on ground features and also summarizes some of the measures which have been used to minimize the possibility of damage to surface structures as a result of subsidence due to underground coal mining.

Jan 1, 1981

By K. H. McDaniel, K. G. Wallace

This paper describes the development of a Windows-based interactive mine ventilation simulation software program at the Waste Isolation Pilot Plant (WIPP). To enhance the operation of the underground ventilation system, Westinghouse Electric Corp. developed a program called WIPPVENT. While WIPPVENT includes most of the functions of the commercially available simulation program VNETPC from Mine Ven- tilation Services Inc. and uses the same subroutine to calculate airflow distributions, the user interface was completely rewritten as a Windows application with screen grap-hics. WIPPVENT is designed to interact with WIPP ventilation-monitoring systems through the sitewide central monitoring system. Data (e.g., air quantity and differential pressure) can be continuously collected from the underground ventilation remote-monitoring and control system and from the mine's weather stations (psychrometric data). Furthermore, WIPPVENT incorporates regulator characteristic curves specific to the site. The program utilizes this data to create and continuously update a real-time ventilation model. This paper discusses the design, the key features and the interactive capabilities of WIPPVENT.

Jan 1, 1998

By K. R. Wood, P. M. Blythe, J. A. Finch, M. L. Lavallee

A new analytical approach for characterizing and improving the performance of ball milling is presented. Individual ball mill circuit design and operating variables can be related to overall circuit performance through two distinct parameters for classification and breakage. The ball mill circuit functional performance equation is presented. Applications in the industrial plant and in the research field are discussed.

Jan 1, 1991

By Robert J. Timko, R. Lincoln Derick

The Bureau of Mines evaluated the integrity of escapeways in a three entry underground coal mine. A center conveyor belt entry (secondary escapeway), was flanked by an intake (primary escapeway) and a return entry. Diesel equipment was used throughout the mine for material and personnel haulage. A carbon monoxide monitoring system, tied to a data recording computer on the surface, was deployed throughout the belt entry and at selected sites in the intake and return entries. Previously, the company had a fire of unknown origin in another mine, which prompted an interest in the performance of their escapeways. An initial, qua1itative evaluation was performed by burning approximately 14 kg of coal at the mouth of the intake entry. The first test was followed by a similar burn at the mouth of the belt entry. These initial trials showed a high quantity of leakage between entries. In several follow-up evaluations, simulated fires, using a tracer gas, were set in the intake and belt entries. Tracer gas concentrations were obtained in all entries at four different underground locations. The results of these tests showed that permanent stoppings could not guarantee isolated, contaminant-free escapeways.

Jan 1, 1989

By C. Cho

One problem with the application of neural networks to the multivariable control of mineral and extractive processing is deciding whether and how best to use them. The objective was to compare neural network control to more conventional strategies and find any advantages in terms of set point tracking, rise time, settling time, disturbance rejection, and other criteria. The procedure was to develop neural network controllers using both historic plant data and simulation models. We tried various neural network control patterns including both inverse and direct neural network plant models. These were compared to state space controllers that were, by nature, linear. For grinding and leaching circuits, a nonlinear neural network-based model predictive control strategy was superior to a state space-based linear quadratic Gaussian controller. We also learned the importance of incorporating state space into neural networks by making them recurrent--feeding certain output state variables into input nodes in the neural network. We concluded that neural network controllers can have better disturbance rejection, set point tracking, rise time, settling time, lower set point overshoot, and can be more foolproof and easy to implement in complex, multivariable plants.

Jan 1, 1996

By A. Ersoy, M. D. Waller

Because of a shortage of diamonds for the drilling industry in the 1970s, efforts were made to develop synthetic diamonds. The resulting development of polycrystalline diamond compacts (PDC) enabled the evolution of a new generation of rotary-drilling drag bits. Bits based on PDC cutters were very successful in drilling soft, abrasive and medium strength rocks. However, because of their thermal instability, they failed rapidly when drilling hard rocks. Thermally stable diamond (TSD) was then developed for hard-rock drilling. The rate of penetration (ROP) and bit life significantly influence the drilling cost. The ROP and the life of the TSD bits or cutters are affected by a number of complex factors. However, in laboratory testing and infield operations, the principal factors that need to be considered in predicting drilling and wear rates are bit design characteristics, bit operating parameters and the characteristics of the penetrated rock. These characteristics are comprehensively reviewed for both laboratory and field drilling results using TSD bits. Optimization of these parameters increases the drilling rate, prolongs the bit life and reduces the drilling cost.

Jan 1, 1998

By Richard J. Wilson

The importance of coal as a major source of energy used by the steel industry has been increasing due to the gradual changeover from steel- making by the open hearth process to steelmaking by the basic oxygen process. Since the production of steel by the BOF process increases the demand for hot metal, there is a growing need to ensure the supply of coke required for the production of hot metal. Coal used for cokemaking has become, therefore, an increasingly important raw material for the steel industry in recent years. Our current projections indicate that coal will be the source of 71% of the total energy requirements of Inland Steel Company in 1985. As a result of the energy shortages of the last few years, various conservation programs have been initiated by the steel industry to reduce the consumption rate of fuel. The efforts to conserve energy have been successful to a great extent due to the rapid advances made in the technology of ironmaking that facilitated gradual reductions in the quantity of coke used per ton of hot metal produced in the blast furnaces. The decrease in the consumption rate of coke was made possible by the use of improved raw materials, such as iron ore pellets and fluxed agglomerates, the operation with high blast temperatures, the injection of auxiliary fuels, and the enrichment of the blast with oxygen. It is expected that additional reductions in the fuel consumption rate will be possible in the ironmaking operations of the large blast furnaces that are being equipped with facilities for proper burden distribution and for operation with higher blast temperatures at high top pressure. The purpose of this paper is to show the effects of coke quality on the production of BOF steel. The importance of coke quality will be pointed out by discussing the effects of the physical strength of coke on both the blast furnace productivity and the steelmaking operations of an integrated steel plant, such as Inland Stee1 Company.

Jan 1, 1980

By Salvatore] [Parand

Deep well disposal is a much used and abused term which is the panacea for wastewater disposal in some minds and creates near hysteria in others. It can be the answer to a difficult waste disposal problem, or if improperly employed, can create more problems than it solves. My purpose in this presentation is to focus on the value and limitations of deep well disposal as expressed by New York State's experience and policies. To he sure, I feel a place for such practices docs exist if adequate safeguards are utilized. I shall give a broad brush approach to New York's legislative, geologic and operational concerns and speak briefly on some case histories. I shall not delve deeply into the technological details since I am not an expert in mining exploration or well drilling.

Jan 1, 1973

By Taneomi Harada

Mine drainage has high acidity and sometimes contains more than the allowable concentration of ionized iron. In such a case, mine drainage is neutralized with calcium carbonate and calcium hydroxide to separate precipitates, such as the iron hydroxide and gypsum generated. Currently, most of these precipitates are not utilized and are accumulated in tailing dams. As a result, the service life of the tailing dams is reduced. This becomes a matter of concern, since securing sites for such dams is difficult. A most effective means of solving this problem would be to promote utilization of these neutralized precipitates. This paper reports on the results of studies on neutralized precipitates produced at the old Matsuo Mine (Iwate Prefecture), which has the largest neutralization treatment facility in Japan. As a result of the studies, the following was proposed regarding application of neutralized precipitates. Utilization as ferrite: Mix ferrous hydroxide and ferric hydroxide in water to synthesize magnetite-like ferrite, to be used in the manufacture of magnetic markers for a mobility support system for blind pedestrians, or in producing magnetic fluids for sink-and-float separation of nonmagnetic metals and nonmetals. Utilization as hematite: Bake ferric hydroxide to produce hematite, thereby extracting metallic iron for paint pigment as well as for the manufacture of ironware by local industry. Production of aluminum sulfate: Precipitate aluminum ions from water and add sulfuric acid to produce aluminum sulfate.

Jan 1, 1995

By Doug Harding

The 3.5 km long Ashbridges Bay Outfall in Toronto, Ontario, Canada was a challenging drive set below Lake Ontario. After a remote machine acceptance due to the global pandemic, an 8 m diameter Single Shield machine launched in March 2021 from an 85 m deep shaft and began its bore in shale with limestone, siltstone and sandstone. During excavation, the TBM and its crew bored a city-wide record of 30 rings in one day, or 47 m of advance. This paper will cover the unique project, from TBM acceptance through to launch, tunneling in difficult conditions, and completion in 2022.

Jun 13, 2023

"INTRODUCTION While the United States coal mining uses prescriptive regulation under the Title 30 Code of Federal Regulation enforced by the Mine Safety and Health Administration (MSHA), Australia uses a risk based approach. Australian regulation is individual to each state. In Queensland, Australia this risk based approach to address principal hazards is underwritten by the Queensland Coal Mining Safety and Health Act of 1999 and the Coal Mining Safety and Health Regulation of 2001. Each Queensland Mine is required to have an overarching Health Safety and Environment Management System, of which Safety Management Plans are an element. “Safety Management plans (SMP’s) are intended to formalise the process by which mines address principal hazards and other related matters to ensure the safety of mine personnel.”7 THE QUEENSLAND CONTEXT In Queensland, the basic elements of a coal mine’s safety and health management system must provide for risk identification and assessment, hazard analysis, hazard management and control, and the reporting and recording of relevant safety and health information and data.5 (Part 2 Division 1 Section 6(a-d)) The initial guidance for writing Safety Management Plans comes from the Approved Standard for Mine Safety Management Plans and Guidance Note QGN09- Reviewing the Effectiveness of Safety and Health Management Systems. The Guidance Note and Approved Standard are supplemental to the Act and Regulation, and put in place to provide more clarity around the topic. The definitions in this section come from the Approved Standard and are included to provide context for those who may not be familiar with Australian or Queensland law and regulation. A hazard is defined as a source of potential harm or a situation with a potential to cause loss, while a principal hazard is a hazard with a potential to cause multiple fatalities. A risk is the chance of something happening that will have an impact upon objectives which is measured in terms of consequences and likelihoods. It is important to be able to make the distinction between a hazard and a risk. For instance, a lion is a hazard, while the risk associated with a lion is getting eaten. As defined by the Queensland Approved Standard for Mine Safety Management Plans, a Safety Management Plan (SMP) requires a systematic definition of all the actions necessary to ensure that mining operations are carried out safely. A SMP includes, but is not limited to organisational structures, planning, activities, responsibilities, practices, risk identification, audits and reviews.7 The goal of a SMP management plans is to mitigate the risks to bring them to an As Low As Reasonably Achievable (ALARA) level."

Jan 1, 2016

By Ingo Kaundinya

"INTRODUCTION Tunnels are important elements of the German federal road network which have to cope with an increasing traffic load especially of heavy goods vehicles. In order to ensure a high availability and safety level for these key infrastructures, big efforts are required by owners and operators in order to keep all infrastructures up to date. This mainly relates to current European regulations regarding tunnel safety (Directive 2004/54/EG) [1] and their national implementation, which must be fulfilled by many existing tunnels. In this context the German Federal Government spends more than 1.1 billion € for the structural and operational retrofitting of more than 120 existing road tunnels. As many of these projects have recently been finished or are still under progress, experiences and best practices could be reported. After the description of current requirements in national standards regarding structural fire protection, the paper gives an example for an upgrade of a tunnel’s fire protection by installing an additional fire protection system, which is a quite costly measure. Another possibility to fulfill current requirements regarding structural fire protection could be the numerical proof of sufficient bearing capacity of a structure. The influence of different fire loads and fire durations on the bearing capacity of typical road tunnel structures have been investigated in a research project funded by the German Federal Ministry of Transport (BMVI) and coordinated by the Federal Highway Research Institute (BASt). The results of this research project have been used to define a procedure how to investigate existing tunnels regarding structural fire protection. Finally, the research results have also been the basis for a current update of national standards for tunnel construction. REQUIREMENTS REGARDING STRUCTURAL FIRE PROTECTION The structural fire protection design of road tunnels is usually based on temperature-time curves of exposure to fire, for simplicity called ""fire curves"". The fire development after fire growth is illustrated with fire curves. Fire curves can be subdivided into a heating-up phase, a fully developed fire phase, and if applicable, into a cooling-off phase (cf. Figure 1). During the fully developed fire, the fire remains at a certain temperature level."

Jan 1, 2016

By Nelson R. Shaffer

Biotechnology has become a household word of the nineties, and it is expected to become as important in the next century as the computer is in the present. Numerous books and articles portray biotechnology developments as nothing less than a scientific revolution. Almost everywhere one looks new biotechnical breakthroughs are being reported that offer almost limitless opportunities to harness the force of living things to produce materials and manipulate their properties. Biotechnology has been broadly defined as any applications of biological organisms, systems, or processes to manufacturing and service industries. This seemingly new technology is, in fact, one of mankind's oldest scientific activities (Table l), which has been recently revolutionized by techniques of genetic engineering that arose out of basic research in biology, biochemistry, genetics, and information sciences. From fields as old as agriculture and medicine to those as new as monoclonal anti-bodies, transgenic plants, or biocomputers are encompassed by biotechnology. Like most human endeavors, industrial minerals play critical roles in biotechnology. In addition biotechnology holds real potential to improve extraction and beneficiation of certain industrial minerals themselves. BIOTECHNOLOGY OVERVIEW Companies using established biotechnical techniques make up large and diverse groups such as agriculture, chemicals, and pharmaceuticals. The massive US Pharmacopia (Anon., 1990a) provides detailed specifications for minerals used in medicines. Alumina, zirconia, apatite, and bioactive glass have seen service as implant materials (Williams, 1990) and new uses for minerals in health sciences are being actively researched. Agriculture produced $361 billion worth of food and drink during 1991 in the United States; organic chemicals, pharmaceuticals, and enzymes accounted for $68, $59, and $42 billion, respectively (Anon., 1992a). It is not possible to separate the contributions of industrial minerals to biotechnical products, but they represent a very large and rapidly growing new field of uses. The new biotechnology has nearly 300 small companies, plus 15 established companies with 742 biotechnology-related firms (Dibner, 1991b). Revenues exceeded $2 billion in 1990 and are expected to grow to $50 billion by 2000 (Anon., 1992c), with worldwide sales exceeding $100 billion (Burrill and Roberts, 1992). Federal research amounted to $3.4 billion in 1990 (Anon., 1992b). The United States is the world leader in biotechnology, but other countries have large, well-funded programs. Despite debate about safety, obstacles to new biotechnology products are declining (Embers, 1992, Gibbons, 1991). Fifteen biotechnology drugs valued at $1.2 billion (Thayer, 1991a) are on the market, and more than 100 are in various stages of testing (Edington, 1992). Many diagnostic tests are also in use or development (Demain, 1983, Anon., 1992). Large scale efforts to produce or transform important chemicals are also underway (Ng et al., 1983, Hinman, 1991), and research into geologic uses of biotechnology has begun. Much has been published about microbial mining, oil recovery, desulfurization, bioremediation, and other geologic aspects of biotechnology, but this chapter is the first attempt to explore interactions of biotechnology and industrial minerals. This chapter examines uses of minerals in biotechnology; how biotechnology can be used to discover, recover, and beneficiate industrial minerals; and speculates on some potential, but as yet untried uses. Definitions What exactly does the word biotechnology mean? Bud (1989) states that the first use of the term was by Karl Ereky in 1919 to cover the interaction of biology and technology, and in 1933 the term was used in Nature. After citing seven different definitions, Smith (1988) concludes that biotechnology is a series of enabling technologies involving practical applications of organisms or their subcellular components to manufacturing and service industries or to environmental management. Walker and Cox (1988) suggest a definition of "the practical applications of biological systems to the manufacturing and service industries and to the management of the environment." Primrose (1991) says that it is "the commercial exploitation of living organisms or their components." There is essentially an older broad use of the term and a new use. The US Office of Technology Assessment (Anon., 1984) uses a broad definition that includes any technique that uses living organisms (or parts of organisms) to make or modify products, to improve plants or animals, or to develop micro-organisms for specific uses. Definitions are different, but they all have several fundamental elements that include the control, management, or manipulation of living things for commercial, industrial, or useful ends. While such a definition encompasses all of agriculture in practice the "new" biotechnology is restricted to processes involving microorganisms-plant and animal cells, or enzymes. Many consider biotechnology to be recent, but it is one of our oldest technologies as evidenced by the prehistoric origin of brewing, cheese-making, and other techniques. [Table 1] gives some of the important developments in the history of biotechnology. Smith (1988) breaks down historical developments of biotechnology into four phases: 1) prehistoric with no understanding of underlying processes; 2) nonsterile processes; 3) sterile processes after 1940; and 4) genetic and recombinant DNA technology deliberate design of special organisms or processes.

Jan 1, 1994

By James K. A. Harral

The growing national concern over energy has aroused a great deal of interest in the most efficient and least costly way to use our remaining fossil fuel reserves. A number of studies have been published which compare the overall thermal efficiency and cost of gas and electric energy. These studies have been carried out by a wide variety of organizations including Oak Ridge National Laboratory, The Rand Corporation, The Stanford Research Institute, and The Institute of Gas Technology. This paper is an attempt, by PGandE, a large combined gas and electric utility serving most of the northern and parts of central California, to compare the cost and efficiency of gas and electric energy for certain residential appliances using actual operating data and financial statistics for the year 1974, and thereby develop some guidelines for future energy developments utilizing these limited fossil resources. The appliances chosen for the study were kitchen ranges, clothes dryers, hot water and space heaters. These appliances were selected because they can be served with either gas or electricity and they account for approximately one-third of PGandE's total residential electric sales and nearly all of PGandE's residential gas sales.

Jan 1, 1976