Search Documents

By Carlos Kovacs-Figueroa

Because of air pollution control regulations in the early 701s it became necessary to clean effluent gases from the Morenci Reduction Works Smelter. Feasibility studies indicated that this could be accomplished most efficiently by using the smelter gaseous effluent to feed a sulfuric acid plant. Complying with air pollution control regulations thus created the need to dispose of relatively large amounts of concentrated sulfuric acid. Typical Morenci ores contain substantial amounts of oxidized copper minerals which are not recoverable by flotation. In addition, there is low sulfide, high oxide material which can be leached, but is not suitable for flotation concentration. Early in 1971 sufficent data had been accumulated to show that a leaching plant for the Morenci tailings could use a large portion of the sulfuric acid produced by the Smelter. It was determined that for all practical purposes leaching of the available copper was complete in two hours or less. Capital expenditures could not be justified for more than two stages of counter current decantation for recovery of the leached copper, and the plant was designed with these criteria in mind.

Jan 1, 1976

By E. H. Ahrens

This paper deals with the daily work of operating geologists and should be of interest to recent graduates. Working with development and production is quite different from exploration and many of the required skills and techniques must be learned on the job. Try to obtain your first position at a mine where good geological work is being done because it is important that you establish a solid foundation by learning valid techniques. Many do not! Those who desire to work in exploration are well advised to spend the initial two or three years at an operating mine where they will deal daily with an orebody during development and mining. Attempt to understand the controls of ore deposition and be interested in all phases of the operation. Learn something about factors which can adversely affect profitability and you will be a better explorationist.

Jan 1, 1983

By Erich U. Petersen

Discussion by Erich U. Petersen Harbuck et al. (1990) present results of research on sulfuric acid leaching of a germanium-gallium ore and shed considerable insight on possible extraction methods for gallium and germanium. However, the presentation does not give sufficient details to evaluate the research, so some of the conclusions may not be as applicable as stated. The objective of this communication is to indicate that relevant and easily obtainable geological and technical information was omitted. Consequently, on this basis, alternative explanations for some of the data are possible. Discussed below are the omission of: • pertinent geological, mineralogical and geochemical literature; • details regarding the determination of germanium concentration in quartz by electron microprobe; and • details on the calculation of the amount of germanium locked in quartz. "These topics are important since the determination of the amount and locus of "unrecoverable, locked germanium" may have an important impact on the economics and methods of germanium extraction and the directions of future research. Harbuck et al. state that "A key to increasing germanium extraction is understanding the mineralogy of the ore." However, only two studies are cited that in some manner describe the mineralogy of the ores. In addition, both of these studies were very preliminary, of limited scope and examined very few

Jan 1, 1993

By Donald E. Scheck, Syed F. Abbas

Public domain ventilation simulation programs have been well accepted by the mining engineers, but preparing the input and interpreting the results are labor intensive tasks. High performance personal computers and versatile CAD packages provide the means to quickly create the network and display the results. The enhanced simulators work from computerized as-mined map, the projected mine layout and timing maps. Using on screen displays of these maps and the snap-on feature of AutoCAD, the planner designates nodes in the ventilation network, connects them into branches and selects the branch characteristics from a side bar menu. The color coded ventilation network appears with the parameters shown along each branch. The software then calculates the length of airways and computes the branch resistances where needed and converts the input into the required format and passes the data to the Pennsylvania State University or U.S. Bureau of Mines ventilation programs. Output is available in graphical as well as report format. The color coded graphs include pressures at the nodes and flow quantities on the branches. Since the networks come from the mine maps, the ventilation displays are to scale and can be plotted separately or superimposed on the mine maps.

Jan 1, 1991

By R. W. Smith, D. Clare

The removal of metals from an acid mine drainage (Leviathan Mine, Alpine County, California) water by precipitate flotation was investigated. The Leviathan waters vary from about pH 4.0 to pH <2.0and contain from about 2,000 to about 12,000 ppm SO42-.The main multivalent metals present in solution are Fe, Ca, Mg, Al and Mn. Both Cu and Co are present in small amounts. The pH was adjusted with lime. The collector used was either sodium oleate or tall oil. The sodium oleate was used as a function of pH to establish optimum flotation conditions and the tall oil was used only at the optimum pH. Dow Froth 250 was used as a frother. In some test additional Cu was added to the system. Excellent recovery of Fe and Cu were achieved at optimum pH. The process achieves results comparable to precipitation and filtration without as much problems with screens blinding because of less material to filter.

Jan 1, 2004

By Earl R. White

In 1950 Kaiser Steel Corporation acquired control of the Utah Fuel Company, a pioneer Utah coal concern owning large reserves of high volatile coking coal near Sunnyside, Utah. The mines at Sunnyside have been producing high quality coking coal since the late 1890&apos;s. Kaiser Steel acquired the coal deposits at Sunnyside in order to supply the necessary coke for its steel plant at Fontana, California. The Sunnyside coal deposits are made up of two mineable beds, the upper and lower Sunnyside seams. Both seams outcrop along the southward facing escarpment of the Book Cliffs. The coal seams dip under the massive sandstones of the Book Cliffs to the northeast at 5 to 22 pct., with the steepest-part being near the outcrop. Mining at Sunnyside up to 1961 had been carried on with room and pillar methods. The deep cover and rotten roof conditions, along with the need of increased tonnage, required a change of mining technique. Numerous ideas were presented, discussed, and economically analyzed. Several people involved in these discussions, with the aid of W.W. II, had been introduced to the European methods of coal mining, namely the longwall technique. The European mines had long been plagued with near similar conditions as those at Sunnyside, particularly the deep cover problem. The longwall method seemed to be working very well under these conditions, and with the extensive studies given longwalling by the Kaiser Steel mining officials, it was decided to give longwalling a try.

Jan 1, 1976

By T. L. Dobecki

Numerous seismic techniques have proven to be important and cost effective aids to both coal exploration and nine planning. Projects conducted by Sandia in recent years have sham seismic refraction is a valuable tool for determining overburden properties while high resolution, 2-0 and 3-D seismic reflection surveys are the primary means of napping coal seam distribution, structure, and continuity. Further, seismic methods utilizing existing boreholes (e.g. downhole, crosshole and guided wave) provide detailed measures of overburden/interburden modulus variation, seam continuity, and calibration for other seismic surveys. Examples include mapping faults of 2-10 m threw in seams 3-15 m thick at depths of 80-300m.

Jan 1, 1982

By Fred H. Lightner

The feasibility evaluation of the Borealis project of Houston International Minerals Corporation (HIMCO) was initiated in October of 1980. The operation of the Borealis Mine and heap leaching plant began in late 1981. In order to achieve the rapid development schedule several items were necessary: 1) Pre-planning of environmental requirements and early study of key issues. 2) Adoption of conservative design criteria. 3) Coordination and cooperation between HIMCO and regulatory agencies. 4) Adoption of specialized engineering and construction procedures. 5) Careful evaluation of owner project management philosophy.

Jan 1, 1982

By Jorgen Elbrond

In a stream of ore in an underground mine or in a beneficiation plant bins are installed between machines or machine system. When the upstream machine is stopped the downstream machine can continue operation for a while and vice versa. The paper describes a procedure for calculating the total capacity of a system consisting of two machines with an intermediary bin as a function of the bin&apos;s live volume and of the installed machine capacities and their production variations, which are defined. Extensions to several machines in parallel and in series are shown as well as practical examples.

Jan 1, 1982

By H. Wesley Peirce

Arizona, in 1966, has continued to be the site of an extensive and intensive search for metallic mineral deposits. Over fifty separate entities--companies and individuals--have been actively engaged in mineral exploration programs, both large and small, in the Basin-and-Range portion of the State. Certainly, copper has been primarily responsible for the major efforts, although associated gold, silver, and molybdenum mineralization also has been important in the economic evaluation of potential copper deposits. It is not difficult to explain why the Basin-Range portion of Arizona is receiving such attention. Part of the story, undoubtedly familiar to most, can be illustrated by reference to three graphical presentations. For example, Figure 1 shows Arizona&apos;s annual copper production for the period 1955-1965, inclusive, and it demonstrates that new records of production have been accomplished in each of the past 6 years and in 9 of the last 11 years.

Jan 1, 1967

By John A. Dearinger, Fred D. Wright, Robert C. Howell

INTRODUCTION The rock mechanics study of the shortwall mining system at Beth-Elkhorn corporation&apos;s Hendrix No. 22 Mine is being conducted under contract with the U.S. Bureau of Mines. The objective of the study is to obtain data on surface subsidence over a portion of the mined area, strata subsidence in the mined area, and underground stress changes and displacements in and near natural support elements of the mining system. This study is currently in progress, and only a portion of the results are being presented at this time. The Hendrix No. 22 Mine is located in the moderately rough mountainous terrain of Letcher County in eastern Kentucky. The nearest mine workings to the shortwall area are approximately 1,900 feet distant. The depth of cover over the mined shortwall area varies from 770 feet at Panel 1 to 170 feet at Panel 5 (Figure 1). The strata in the shortwall area is summarized in the three core logs shown in Figure 2. Hole no. 2 is located in approximately the center of the mined shortwall area (Panel 3, Line C, Figure 1). The coal seam in the shortwall area is approximately 4 feet thick and horizontal, although one major ‘roll’ intersects all panels.

Jan 1, 1977

By A. W. Wensel

The adsorption behavior of sodium oleate on brucite, Mg (OH)2, has been studied by Fourier transform infrared spectroscopy. Both internal reflection and diffuse reflection (DRIFT) methods were used to characterize the adsorbed oleate on brucite. DRIFT measurements were shown to be quantitative, and an equilibrium adsorption isotherm was obtained. The conformational behavior of the adsorbed oleate was investigated as a function of adsorption density. It was found that at sub-monolayer coverage the alkyl chains of the adsorbed oleate had more ?gauche? character than at multi-layer coverages. Also, DRIFT spectra revealed that the adsorbed species were magnesium dioleate. For internal reflection measurements single crystals of MgO were hydrolyzed to form a thin Mg (OH)2 layer.

Jan 1, 1994

By L. M. Pruett

The Arizona Legislature is currently in the process of considering mined land reclamation legislation in the 1994 legislative session. A bipartisan legislative study committee has drafted proposed mined land legislation. The committee has attempted to craft legislation that is appropriate for the unique conditions in Arizona. Existing Arizona and federal laws and regulations extensively regulate the environmental performance of mines in the state to protect public health, safety and the environment. The proposed mined land reclamation legislation does not replace or duplicate these statutory provisions relating to environmental protection. Instead, the purpose of the proposed legislation is to provide for the reclamation of land that is being mined and to fill the gap in existing laws by requiring the reclamation of land that currently is being mined or that has been mined since 1986 to provide for future land use. The legislation would require an operator to submit a reclamation plan describing the exploration operations, mining operations, post-mining land use and the proposed reclamation measures for review by a state agency. Financial assurance also would be required in an amount such that a third party could complete the approved reclamation measures. Arizona&apos;s mined land reclamation legislation would recognize Arizona&apos;s leading role in hard rock mining and emphasize the mining industry&apos;s economic importance to Arizona and the nation. Because mining operations necessarily require disturbing the surface of the earth to extract valuable minerals, reclamation requirements would be adapted to different conditions and would vary depending on site-specific conditions and on the commodity being mined. The current proposal does not identify the state agency that will administer the mined land reclamation program and approve reclamation plans, substantial changes to plans, and transfers of reclamation plans to other operators.

Jan 1, 1994

By F. P. Schwarz

Even in an otherwise care-fully done sampling procedure, reducing subsample weight, or splitting, when the grain size of material is too large commonly generates significant error. Such error can be estimated from the standard deviation of differences between values of PAIRED ASSAYS. Samples from split-ting steps immediately before comminution, and showing a restricted range of grade, generate paired assays. Splitting steps characterized by relative standard deviations exceeding 16% generate nonrepresentative data. Such steps should be redesigned to optimize reliability of assay-dependent studies. A sampling scheme can be graphically characterized, and then redesigned as appropriate, using a SAMPLING NOMOGRAPH. Use of the nomograph avoids continued replication of assays. Generally at a splitting step, excessive error can be reduced by comminuting more material. Unnecessary effort can be mitigated by comminuting less finely and/or by splitting to a smaller weight.

Jan 1, 1992

By J. Scott McDougall, J. Herman P. Eng. Vanderlaag

An underground mine fire can seriously threaten the lives of all personnel in the mine. This fact makes fire emergency planning a high priority in the mining industry. The optimum warning alarm must be fast and able to reach all miners, regardless of their location or work activity. Current means of fire warning are varied, and include such methods as stench, telephones, and word-of-mouth (messengers). Unfortunately, none of these methods are entirely satisfactory. A novel fire warning alarm which enables instantaneous warning of all underground personnel, the Canary Nine Messenger System, has been developed by VLF Magnetic Systems Inc. in conjunction with Noranda Technology Centre and the U.S. Department of the Interior - Bureau of Nines. The warning is sent by an electromagnetic signal which penetrates through mine rock to receivers housed in the battery packs which also power each miner&apos;s cap lamp. A loud buzzer in the integrated battery/receiver unit and the flashing of the cap lamp alerts miners to incoming messages. Testing of prototype equipment has demonstrated that the transmitted signal is capable of penetrating through over a mile of mine rock and activating the receiver. This report describes the theoretical basis for through-the-rock ultra-low frequency electromagnetic transmission, and the design of recently available transmitter and receivers.

Jan 1, 1995

By D. E. Traut

A fluidized countercurrent ion-exchange system was developed, operated, and evaluated by the Bureau of Mines. The system consisted of integrated multiple-compartment absorption and elution columns in which the solution flows are continuous except for short periods when resin increments are withdrawn. The exchange of uranyl sulfate between a simulated acid leach uranium solution and a strong-base, ion-exchange resin together with the subsequent elution with an acidified sodium chloride solution was studied. The effects of the number of sections, section heights, amount of resin withdrawal, and solution flow rates were investigated. Also examined were the kinetic and equilibrium relationships for the absorption step. The experimental data indicate a strong interdependence between variables. Solution retention time appears to be a major limiting variable. The column was efficient over a range of conditions, but close control was needed for optimum operation.

Jan 1, 1975

By F. M. Doyle, K. Osseo-Asare, E. Peters

With the aid of molecular orbital theory, a discussion is presented of the relationship between the electronic structures of ions and molecules, and the elementary steps involved in homogeneous electron transfer reactions. An electronic theory of the reactivity of oxidants and the mechanism of action of oxidation catalysts is then presented, with emphasis on the oxidative decomposition of metal sulfides. For model oxidants, two molecular reagents: O2 and Cl2, and two ionic reagents: Fe3+ and CU2+ were selected; silver (1) was chosen as the model catalyst. The reactivities of these reagents are rationalized in terms of constraints on orbital overlap, the availability of unoccupied d orbitals, and the rearrangement of electronic configurations.

Jan 1, 1993

By Stephen D. Hill, C. R. Ferguson, T. H. Jeffers, P. G. Bennett

The U.S. Bureau of Mines' Salt Lake City Research Center has developed porous polymeric beads containing immobilized non-living biological materials for extracting metal contaminants from waste waters. Immobilized biological materials include peat moss, algae, biological polymers, and other materials that demonstrate high affinities for heavy metals. The beads, designated as BIO-FIX beads, have distinct advantages over traditional methods of utilizing biological materials in that they have excellent handling characteristics and can be used in conventional processing equipment or low-maintenance systems. Toxic metals such as copper, cadmium, zinc, lead, and mercury are several of the many heavy metals effectively removed from mine waste waters using BIO-FIX beads, Continuous cyclic testing indicated that the beads continued to produce treated effluents which met National Drinking Water Standards (NOWS) after 150 loading-elution cycles. Adsorbed metals were removed from the beads using dilute mineral acids. In many cases, the extracted metals were further concentrated to enable processors to reclaim the metals, thus minimizing the generation of a hazardous sludge, Tests indicated that use of the beads in a low­maintenance system was particularly effective for treating remote acid mine drainage waters and small toxic seeps from hard-rock mining districts.

Jan 1, 1991

By Curtis A. Pledger, H. Lee Wimmer, I. Michael Gowring

The Upper Diamond Fork Project, as part of the Central Utah Project Completion Act, conveys water six miles from the existing Sixth Water Aqueduct to the Diamond Fork Pipeline. During design, a Value Engineering team proposed a single-tunnel alignment that would be less destructive on the environment and might have a lower life cycle cost than the proposed design of two tunnels connected by two pipelines on steep hillsides. A decision was made to include this option in the bid process as a design-build alternative. The bid for this option was the lowest and a contract was awarded. During the TBM excavation a segment of tunnel wall caved in containing large quantities of water saturated with extremely high levels of hydrogen sul?de (H2S)gas (measured at 380 to 520 ppm in the air). The Central Utah Water Conservancy District (District) in consultation with Obayashi/Clyde (Contractor) quickly developed anew plan to finish the system by incorporating parts of the original tunnel/pipeline concept and re-bid the remainder of the project as a Phase 2 Design-Build contract.

Jan 1, 2003

By Regina N. Tempel, Mae S. Gustin, Mark A. Engle

This study characterizes the hydrogeochemistry of groundwaters near opalite-hosted epithermal hot-spring type mercury deposits in the Ivanhoe mining district, Elko County, Nevada. Local groundwaters generally range from Ca-HCO3 to Ca-Mg-Na-SO4 type waters with background mercury concentrations ranging from 0.014 to 0.32 ug/l. Leaching experiments conducted on mineralized rocks, using typical water chemistries to represent local groundwaters, yield total mercury concentrations ranging from 6.3 ug/l to 27.4 ug/l after one year of reaction. Geochemical modeling indicates dissolved mercury is dominated by HgO(,) and that precipitation of quicksilver controls mercury concentrations to an upper limit of 63 ug/l.

Jan 1, 2000