Search Documents

By K. Nagata, T. Kawashima, S. Tejima

The expanding volume of maritime coal transportation is intensifying the problems concerning large vessel service, port construction, trans-shipment, and environmental control. The major problem is the shipment of coal. Customary methods for bulk transfer must be improved and new systems developed. Slurry unloading has a key role in the new systems. This report reviews progress in slurry transportation research that has been done in Japan since the 1960s, when large-scale experiments for domestic transportation were done. Experiments on the effects of vibration on the slurry cargo and on reslurrying are focused on.

Jan 1, 1987

By Francis G. Stehli

Though sedimentary rocks comprise only about five percent of the volume of the continental crust, they cover about 80% of its surface, serve as important reservoirs for fluids, contain reserves of non-metallic minerals, and have in general been extensively drilled. However, most drilling has been shallow in comparison to the thickness of the crust and such deep drilling as has taken place is very strongly localized in sedimentary basins. This may be seen by reference to Figures 1 and 2 which show the location of wells that drilled deeper than 15,000' [=] 4.6 km. (Figure 1) and those that drilled below 20,000' [=] 6.15 km. (Figure 2). It is apparent that, even in regions of sedimentary cover, direct exploration below six kilometers has been very restricted. In the case of the metamorphic and igneous rocks which make up 95% of the volume of the crust, direct exploration has been much less extensive in terms of both area and depth. The present state of our knowledge of the crust below a' thin surface layer stands in marked contrast to our growing present need for raw materials and the needs of future generations. It also stands in contrast to our need for enhanced, scientific knowledge of the deeper crust, its configuration, its present state, its hydrothermal systems,-its evolution, and its materials. Lessons learned in exploring the third dimension of the sea floor, the vigorous prosecution of seismic profiling, the development of testable models for hydrothermal systems and mineral deposits, the need for better understanding of heat flow, state of stress, earthquake mechanisms, and a host of other phenomena all suggest that it is time to launch a national program for scientific exploration of the crust which uses drilling to test important hypotheses developed on the basis of indirect evidence.

Jan 1, 1985

By Adam Levy, Thomas Novak, Sampurna Arya, Joseph Sottile, Kozo Saito

The use of a woven wire-mesh screen as part of a flooded-bed dust-scrubbing system is popular in the underground coal mining industry. It is used in combination with a demister (mist eliminator) to remove dust from the dust-laden air. A study was conducted to measure the pressure drop across a flooded-bed, wire-mesh screen at different airflow rates in one-phase (dry) and two-phase (wet) conditions. Two empirical relationships between pressure drop and air velocity were developed for dry and wet conditions, respectively. In both cases, the form of the empirical relationships was found to be similar to relationships given by Sabri Ergun for high velocity, non-Darcy, single- and multi-phase flow through porous media. The experiments were repeated on a reduced-scale model of the wire-mesh screen, and the pressure-velocity relationships obtained from the full-scale prototype experiments were tested. The test results show validation of the full-scale empirical formulae on the small-scale model with an insignificant variation. This paper presents the empirical equations for pressure drop across the wire-mesh screen in dry and wet conditions. Researchers can use these equations as a tool to predict total pressure drops for wire-mesh screens of different scale sizes.

By F. F. Peng, S. S. Peng, V. Z. Sun

A detailed study of ponding phenomenon relative to surface subsidence due to longwall mining was conducted for various surface stream conditions. Based on field monitoring, the stream-ponding process and three forms of stream water are described. Also discussed are the criteria of stream ponding and the influences on the ponding process by two key factors: the angle of stream flow and the change in the stream-bed gradient. A numerical (mathematical) model, which combines trend surface technique that describe the topographical features in the vicinity of a stream and the modified influence function, which represents the profile of the surface subsidence trough (or basin), is constructed to predict the formation characteristics of stream ponding in terms of location, boundary and accumulated water volume of migratory and stationary ponds produced by the stream-ponding process. Three cases are analyzed using the model to predict the interaction of the underground operations and the environmental impact due to stream ponding. The feasibility of various mitigative measures are assessed.

Jan 1, 1997

By Agus Sasmito, SRIVATSAN JAYARAMAN SRIDHARAN, Akash Adhikari, Purushotham Tukkaraja

The amount of toxic fumes produced during blasting operation depends on the types of explosives used, product formulation, degree of confinement, conditions of use, and reactivity of the explosives with the host rock. Ammonium nitrate and fuel oil (ANFO) is still the explosive of choice due to its lower price and ease of use/loading. If not properly monitored and controlled, toxic fumes produced from blasting operations can have serious health hazards [1]. This paper presents a novel technique developed to track trapped fumes during a development blasting.

Aug 1, 2022

By Robert Cook, Valeria Zarate, Jason Hallowell

The long hole open stoping (LHOS) method is widely used in underground mining. While methods to predict stable stope geometries are well established, the ability to maintain a stable back often assumes effective ground support across the full stope span. The efficacy of the support strategy is dependent on rock jointing, quality, density, top cut width and height, and the type, amount, and orientations of bolts installed. However, it is becoming increasingly common for operators to assume narrow top cuts in service of wider stope spans with minimal bolting coverage. Failure to account for the required top cut drift size and support requirements can ultimately lead to raveling type instabilities along stope shoulders that result in back collapse. A new method has been developed to evaluate the minimum top cut dimension necessary to accommodate wider stope spans with various rock bolting configurations. Due to the economic impacts of top cut development and support, this is a critical consideration in the accurate costing and scheduling of a LHOS operation. Tables 1 lists the acronyms are used throughout this paper.

Feb 1, 2025

The floatability of a bituminous coal in NaG solutions was evaluated using a modified Hallimond tube to delineate the role of the electrostatic interaction between bubbles and particles in determining the coal hydrophobicity. Zeta potential measurements showed that bubbles are negatively charged in the entire pH range tested, while coal particles are positively charged below pH 6.0 and negatively charged above it. Also, both sodium and chloride ions were confirmed to act as indifferent ions without any specific effects for both coal particles and bubbles. Flotation as a function of pH exhibited a maximum and minimum at low salt concentrations which is shown to be determined mainly by the coal hydrophobicity as measured by a new hydrophobic levitation technique. At high salt concentrations (above 0.1 mole/dm3), the flotation without such maximum or minimum is controlled by the electrostatic interaction between the bubble and the particle.

Jan 1, 1992

By Wen L. Chen

The steam coal quality is less stringent than metallurgical coal quality. The steam coal is prepared either by cleaning full size range of raw coal or cleaning coarse coal only, leaving the fine coal raw. The latter scheme is more cost competitive. It is particularly applicable to U.S. eastern soft coal where low ash coal is concentrated in fine sizes. For raw coal size separation, a recently developed Rotating Probability Screen, developed by the British Coal Board, may be advantageously used for easy change of raw coal separating size and to avoid screen deck plugging when handling wet and clayey raw coals.

Jan 1, 1983

By R. W. Mossman, George E. Heim

Seismic exploration techniques offer the engineer and geologist a way of obtaining detailed information on the physical parameters and geometry of the rocks where extensive underground excavation or tunneling is proposed. Use of the seismic method can provide a greater amount of detailed information at relatively less cost than can be obtained by any other known subsurface exploration method. Boreholes are still required for calibration of the seismic data but at a much wider geographic spacing than otherwise would be needed for subsurface mapping. The seismic data can define with precision the actual location of zones of flexure or fracture of the rocks and reveal the configuration of the surface of the rock layers. ENGINEERING PROBLEMS One of the major requirements in the planning of subsurface installations is that of locating tunnels and other underground openings in favorable rock units. Such rock units should exhibit uniformity of composition, both vertically and horizontally, to minimize variation in excavation techniques. The depth and thickness of the unit must be known: a 30-foot diameter tunnel cannot be contained in a 25-foot thick limestone. The rock unit needs to be as free as possible from structural defects and should be suited to efficient excavation procedures. If liquid conduits are planned, the slope of the rock unit needs to be known so that maximum advantage can be taken of gravity flow with the tunnels wholly contained within the unit.

Jan 1, 1997

By P. L. Sibrell

Previous research by the U.S. Bureau of Mines showed that autoclave cyanide leaching of used automobile exhaust catalysts for recovery of platinum group metals (PGM) was technically feasible. This work involves a more detailed investigation of the chemistry of the dissolution of PGM in cyanide solutions. The PGM species in solution identified by ultraviolet spectroscopy. Pt and Pd cyanide complexes were square were The planar in geometry, while the Rh complex was octahedral. The rate of dissolution of the PGM was also investigated using a rotating disk technique. Dissolution rates increased in the order of Rh, pt, and Pd, respectively.

Jan 1, 1994

By M. E. Poad

In 1986, a cooperative effort by the Homestake Mining company, the U.S. Bureau of Mines and the University of Utah was initiated to determine shaft stability while recovering high grade ore in a nearby pillar. Premining finite element simulations indicated the shaft would remain in elastic ground. Six years have elapsed and, despite some initial concern during the first lifts, it appears that the bulk of the original reserve will be safely and profitably recovered. An integrated application of rock mechanics tools from laboratory testing through numerical modelling to mine measurements and observations contributed substantially to the operational success of the project.

Jan 1, 1994

By E. William Rossi, Audrey F. Glowacki, Richard L. Unger

The U.S. Bureau of Mines has developed a graphics-based computer model to assess operator visibility for continuous miners, shuttle cars, and scoops. Using digitized drawings of the machine, the program can analyze visibility for both 5th percentile female and 95th percentile male operators. This model was used to predict 95th percentile male operator visibility for two shuttle car designs. These results were then compared to those obtained from a manual assessment of visibility using the actual shuttle cars. The methods showed good correlation except for several cases which were attributed to imprecise digitization of the machines.

Jan 1, 1992

By C. I. Basilio

The adsorption of O-isopropyl-N-ethylthionocarbamate (IPETC) and O-isobutyl-N-ethoxycarbonylthionocarbamate (IBECTC) on chalcocite, chalcopyrite and pyrite has been studied using UV and in-situ FTIR~ATR spectroscopy. Thionocarbamates were found -to adsorb strongly on chalcocite at pH 4-10, but consider-ably less on chalcopyrite and pyrite. The FTIR spectra show that the surface species of thiono-carbamates are bonded to metal atoms on the mineral surfaces. However, at high concentrations, IBECTC also forms physically-adsorbed species. Adsorption of these thionocarbamates cannot remove or prevent the formation of sulfoxy oxidation products on pyrite, unlike the case with the xanthate-pyrite system. This finding may account for the observed flotation selectivity of these reagents against pyrite. The spectroscopic information is compared with flotation test results.

Jan 1, 1988

By Noel A. Genco, Edward F. McCarthy, Robert J. Piniazkiewicz

Talc, when it can be isolated as a pure mineral, has a composition of 63.36% SiO2, 31.89% MgO, and 4.75% H,O. However, as a commercial commodity less than half of all talc sold has a purity exceeding 95%. Nevertheless, impure talc products find a multitude of uses and few substitutes in many industrial applications. Minerals commonly associated with and sold together in talcose mixtures are chlorite, dolomite, mica, magnesite, and tremolite. Steatite was originally a mineralogical term applied to pure talc. Today steatite usually denotes a high-talc ceramic body used as an electrical insulator, and the talc used in such applications is known as steatitic talc. Steatitic talc generally is found in massive, high- purity form and in the past was machined directly into electrical parts, which rarely is done today. Impure varieties of massive or block talc are still commonly termed soapstone. Soft massive talc, suitable for crayon manufacture, has been referred to as French chalk. It has been common practice to discuss talc, soapstone, and pyrophyllite under the same general heading. In the case of soap- stone and talc this is natural, since many different types of platy, soft minerals exhibiting a high degree of lubricity (commonly referred to as slip) have been grouped together and called soapstone or talc. Further, there are mineralogical relationships between pyrophyllite and montmorillonite and between talc and hectorite. Thus, talc and pyrophyllite are sometimes referred to as clay minerals. When finely divided talc or pyrophyllite are combined with water in proportions to make a slurry, the end product does have the appearance of a clay-water mixture. Soapstone for utensils and ornaments was mined by prehistoric Native Americans on Santa Catalina Island, CA. In the mid- 1800s soapstone from deposits along the western foothills of the Sierra Nevada Mountains was used by white settlers as building and ornamental stone and for the linings and foundations of furnaces (Anon., 1956). Previous to 1916 the annual recorded production in California did not exceed 1.8 kt. From 1912 to 1918, however, output rose sharply when the Talc City, Western, and Silver Lake mines were put into operation. From 1916 to 1935, the state's annual output of talc was in the range of 8.2 to 18.2 kt. There was another increase in the mid-1930s, when the use of talc in wall tile grew rapidly. In California the production of talc grew to 57.2 kt in 1943. The post-war building boom helped California's production to grow to 108.9 kt in 1951. Production stood at 149.8 kt in 1968, 13 1.6 kt in 1969, 167.9 kt in 1970, and 140.7 kt in 1972. In the mid-seventies and early eighties, however, California's talc production declined to approximately 20 kt in 1992 due to reserves exhaustion and the material's tremolite content, which raised significant product liability concerns at the time. Talc mining in New York State dates from about 1878, when a Colonel Palmer and associates opened the first commercial talc mine on the Nelson Freeman farm near Talcville. In 1893 this operation was sold to International Pulp Co., which changed its name to International Talc Co. in 1944. The company was acquired by R.T. Vanderbilt Co., Inc., in 1974. A new talc operation, Gouverneur Talc Co., owned by R.T. Vanderbilt Co., began operations near Balmat, NY, in 1948. The initial capacity of the processing plant was 180 tpd (Gillingham, 1950). Subsequent expansions have increased capacity to more than 725 tpd. Talc was discovered in the area of Johnson, VT, in 1902, marking the birth of the Vermont talc industry. American Minerals Co. initiated plant operations at Johnson in 1904. MagnesiaTalc Co. opened a plant at Waterbury, VT, in 1913 (Burmeister, 1963, Trauffer, 1964) and acquired American Minerals Co. in 1923. The Waterbury mine had a long history as a producer of talc crayons. Eastern Magnesia Talc Co. was formed in 1924 by the merger of Eastern Talc Co. and Magnesia Talc Co. In 1956 Vermont Mineral Co., with a talc mine at Hammondsville, VT, was also acquired. A new plant was then built at Gassetts to produce roofing products. In order to produce high grade products for several markets, Eastern Magnesia Talc Co. began operating a modem froth flotation plant at West Windsor, VT, in 1964. The ore was provided by the Hammondsville mine. This operation, known as Windsor Minerals, Inc., continued from 1972 to 1989 as a subsidiary of Johnson and Johnson Co. In 1989 Cyprus Minerals Co. acquired Vermont Talc, Inc. and Windsor Minerals, Inc.. thus consolidating the talc mining and processing operations at Hamm, Windham, Johnson, Chester, Ludlow, West Windsor, Troy, and Reading, VT, under one ownership. As the result of Cyprus' sale of its worldwide talc assets to the RTZ Group in 1992, its US talc operations are now part of Luzenac America, Inc.

Jan 1, 1994

By Dwayne C. Kicker, Duk-Won Park

As the use of longwall mining increases in the U.S.. there is a need to better understand the stress redistribu- tions indicative of this method. To control high stress concentrations, the yield pillar concept has been developed. A physical longwall mine model has been designed to study the effect of yield pillars in deep mining. The model in- cludes sensitive stress measuring devices, a new excavating technique, and a new model material. This study includes the use of both regular and yield pillar systems and has successfully simulated the mode of stress change in chain pillars.

Jan 1, 1986

By Houston Kempton, David Atkins

Mining in semi-arid climates can produce environmental impacts that will not begin for hundreds of years, but once started, may continue for thousands of years. Pit lakes may eventually exceed toxicity thresholds as metals are evaporatively concentrated, and slow unsaturated flow through acid-generating waste can eventually load several kg-SO4/m2-yr to underlying water tables. U.S. regulations are poorly equipped to respond to delayed and long-term environmental impacts, delaying permits as operators and regulators grapple with uncertainty. Improved uncertainty analysis, additional long-term mitigation options, and explicit regulatory guidance offer solutions to this dilemma.

Jan 1, 2000

By Stephen G. Whittaker, Rosalind A. Schoof, Martha J. Steele

In determining remedial action objectives for metals in soils, the U.S. Environmental Protection Agency typically assumes that the metal concentrations in house dust are the same as the metal concentrations in soil. Data now available from several studies that were conducted in mining communities suggest that for some metals, concentrations in house dust may be lower than those in soil. This paper reviews available data on the relative soil and indoor dust concentrations of arsenic and cadmium and examines how changing assumptions regarding indoor dust concentrations of arsenic affects risk assessments and determination of cleanup levels.

Jan 1, 1992

By T. Ruff, J. Steele

The lack of visibility near earthmoving equipment results in an average of five fatalities in U.S. surface mines each year. These accidents occur when a piece of equipment either strikes another vehicle or worker, or travels over the edge of an embankment. Researchers at the National Institute for Occupational Safety and Health have evaluated off-the-shelf proximity warning systems that sense obstacles near the equipment and provide an alarm to the operator. Limitations of existing systems have necessitated the development of new systems designed specifically for mining equipment, including a GPS-based proximity warning system and a computer-assisted stereovision system.

Jan 1, 2004

By Kirk Conway, Richard L. Unger

The U. S. Bureau of Mines conducted a research project to analyze the design of underground mining equipment with respect to ease of maintenance and maintainer safety. The work included a review of maintainability design literature, an analysis of maintenance related accident data, field reviews of equipment designs, and interviews with mine maintenance personnel and equipment manufacturers. Based on the findings, a set of maintainability design recommendations have been prepared. The final recommendations document includes maintainability engineering information for equipment designers, as well as a buyers' guide to aid purchasers of mining machinery in evaluating the maintainability of equipment.

Jan 1, 1992

By Michael Michaylov, Elana Vlasseva

This paper presents a method for three-phase foam preparation recipe optimization. The pressurized foam is injected into porous media of gob area for prevention and fighting of SPONCOM fires. The method includes laboratory experiments for main foam properties as well as mathematical optimization procedure. Optimization criteria are formulated reflecting foam application purposes. The influence of solid phase on foam heat stability is shown. Results from optimization procedure for four foam agents by varying fly ash consistency of foam are presented. Theoretical basis for original construction of foam generator, specially constructed for of three-phase foam generation, is set u

Jan 1, 1997