Search Documents

By A. J. Kwitowski

Remote control for mining machines ordinarily means the operator is not seated on the machine, but is located within direct view of the machine and work area Thus, remote control operators are exposed to the hazards of roof/rib falls and dust/methane explosions. The U.S. Bureau of Mines has developed a method to disassociate remote operators from these hazards. Off-board, computer-based "tele-operational" systems are utilized that station the operators one-hundred meters or more distant from the working faces. Details are provided for tele-operated systems for thin-seam extraction and haulage equipment in highwall and deep, room-and-pillar coal mines.

Jan 1, 1992

By A. B. Cecala

An evaluation was recently performed on a district recirculation system at a trona mine in Granger, Wyoming. A 1.52m (5 ft) diameter, 37.3kw (50 hp) vane axial fan was installed in a crosscut between the intake and return airways and recirculated approximately 31.4 m'/sec (66,578 ft'/min) of air back into the intake. This amounted to a recirculation factor of approximately 20 pct of the return air. This air was part of the primary ventilation to three different continuous miner sections at operating distances of between 6l0m (2,000 ft) and 1,829m (6,000 ft) from the recirculation fan. The mine environment was constantly monitored for respirable dust, methane, and carbon monoxide in the operating sections and in the main intake and return entries. In addition, air samples were taken with and without the recirculation system during the evaluation and analyzed using gas chromatography. The results of this study showed only small increases in dust, while all other mine contaminants remained at such low levels that it was impossible to determine any relative changes from the recirculation system. Because of this, a brief SF. tracer gas analysis study was subsequently performed to more precisely determine an increase in a mine contaminant with the recirculation system.

Jan 1, 1991

By H. Habenicht, E. Urschitz

Three mining methods for full extraction in flat coal seams - i.e., longwall (L W), shortwall (SW), and rib pillar extraction (RPE) - are com- pared with each other in view of the introduction of a mechanized, self-advancing roof support. Features are shown according to which RPE appears most attractive under certain conditions. In this presentation, the mining methods are outlined and discussed. The new support (Alpine Breaker Line Support, ABLS) is described, and its employment is explained. A trial operation in RPE using the ABLS has been conducted successfully in a South African coal mine. The results and improvements are stated.

Jan 1, 1988

By S. Shankar

The phenomenon of re-entrainment is seen in many environments, such as sand dune formation, soil erosion, fugitive dust emission, spread of radio-nuclides from accidents involving nuclear weapons, etc. A thorough review of existing literature reveals that work on re-entrainment of dust in mine atmospheres is scant. The present study was undertaken as a part of on-going research in the Respirable Dust Center on the prediction of ambient dust concentrations in mine atmospheres (Ramani, 1983) to identify the contribution of dust re-entrainment to the spatial and temporal concentration in mine airways and included wind tunnel and in-mine studies. A set of seven experiments was performed in the Lake Lynn Laboratory Mine of the U.S. Bureau of Mines under controlled conditions. Two types of source coal dust, anthracite and bituminous, were subjected to airflow with a range of air velocities and walking by two different walkers. Six sets of instruments were used along the test section for sampling the airborne particles. The average air velocity just above the coal dust bed varied between 2.1 to 3.2 m/s. Due to re-entrainment as a result of the airflow conditions, the average respirable dust concentration in the center of the mine airway increased to 0.09 mg/m3 (standard deviation = 0.03 mg/m3) from an initial value of 0.02 mg/m3. The concentration of all (i.e., total) airborne dust increased to 0.17 mg/m' (standard deviation = 0.10 mg/m') from an initial value of 0.02 mg/m'. The action of personnel walking, however, caused higher amounts of re-entrainment. Average concentration of respirable and total dust at the center of the mine airway increased to values of 0.28 mg/m' (standard deviation = 0.12 mg/m3) and 1.53 mg/m3 (standard deviation = 1.0 mg/m3), from initial values of 0.03 mg/m3 and 0.05 mg/m3, respectively. It was observed that the dust concentrations were much higher near the floor, immediately at the end of the coal dust bed. Depending on the level of activity and the amount of dust deposited in mine airways, re-entrainment may become an important source of airborne dust away from the point of actual mining.

Jan 1, 1994

By Bee R. Waples

The Alimak Raise Method, using the Alimak Climber, has proven to be a new, fast, economical method of driving raises at the Iron King Branch of Shat-tuck Denn Mining Corporation, Humboldt, Arizona. In order to fully understand the advantages of the Alimak Raise Climber, it is necessary first to describe the basic machine; second, a complete cycle of a raise round; and third, the comparative speed and economy afforded the Iron King operation by using this new method of raise driving: The raise climber consists of a drilling platform that is raised and lowered by two 6.2 HP compressed air motors that drive, through roller chains and sprockets, three worm gears connected in series. These worm gears drive pinions which grip the guide rail rack. The worm gems are fitted with spring-loaded couplings so that a small rock or grit in the rack is passed over without disturbing the mesh between the rack and the other pinions.

Jan 1, 1961

By Kendrick C. Hardcastle

The practice of transporting an ore or matrix from a pit area to the plant process area by means of a hydraulic pipeline has long been used by the mining industry. The industries which have classically used hydraulic transportation of ore to the plant include the phosphate mining industry, the heavy minerals mining industry, the clay mining industry, and the sand mining industry. As the advantages of this method become better known throughout the mining industry as a whole, and as techniques and expertise improve, its use will undoubtedly spread. Its use is presently being contemplated in iron mining diatomaceous earth mining, and several industries where massive removal of overburden is a predicate to economical mining. The widely recognized advantages of hydraulic transport at ion of ore from the pit area to the mines are: 1) Its relatively low initial capital costs. 2) Its speed of relocation at the mine site. 3) The washing and scrubbing action given to the ore by its hydraulic passage into the pit pump and the subsequent trip through booster pumps down the pipeline to the plant.

Jan 1, 1969

By Noel Jarrett

Energy consumption and distribution in aluminum production, conservation accomplishments, and future goals are presented. Electrolysis and electrode manufacture show the greatest promise for major improvements. Means are proposed for reducing waste heat generation in smelting and for conserving energy in anode manufacture by furnace design and substitution of other materials for petroleum coke. Hall-Heroult Process modifications, alternative designs, and the Alcoa Smelting Process are discussed as energy savers. Scrap recycling, more use of aluminum in transportation, and the installation of offshore smelters in less developed countries are shown to be additional means of coping with possible energy dislocations.

Jan 1, 1981

By B. Mishra, A. Staley, D. Kirkpatrick

The major waste product of the alkaline extraction of alumina from bauxite (Bayer Process) is known as red mud. Approximately one ton of red mud is produced for every two tons of bauxite mined. The red mud produced from Jamaican bauxite is rich in hematite, alumina and titanium oxide. It has been shown that more than 90% (by weight) alumina can be recovered from red mud by soda ash sintering and caustic leaching. Hematite can be carbothermically reduced with a degree of metallization of more than 94%, resulting in attempts, for magnetic separation. These separations are desirable because there are no waste products generated. Consequently, there is an opportunity for complete utilization of the waste material. Conversely, the preseparated material could be charged through the tuyeres in an iron blast furnace, or it could be smelted to produce pig iron. If smelted, the concentration of titanium oxide in the slag would be high enough to justify its recovery by an established acid-leach process. This paper describes the results of alumina recovery and the plans for titanium oxide recovery from red-mud. In addition, the situation of ongoing efforts in iron extraction, particularly, the method of magnetic separation of the reduced material. The problems associated with the use of reduced red mud as an alternative to direct-reduced iron (DRI) is also discussed. A critical assessment of the recovery sequence chosen for the products is described based on economics. Key words: Red mud, Waste product utilization, Alumina recovery, Titanium oxide, Iron

Jan 1, 2003

By G. R. Giuliani

Hanna Mining Company's Groveland Mine is located in the Upper Peninsula of Michigan. The low grade iron ore deposit consists of a mixture of magnetite and hematite with chert, jasper, quartz and various iron silicates (1). The ore is beneficiated by magnetic separation and anionic flotation of the iron minerals with chemical depression of the silica. The magnetic concentrate makes up about 75% of the concentrate. The concentrate is pelletized at the rate of 2.0 million LTPY of pellet production. The concentrator facilities were started up in 1959 and the concentrate was marketed as sinter feed until 1963 when the concentrator was expanded and the pelletizing plant was added. The pellet plant now consists of regrinding, elutriation, filtering, balling and induration. The pellet machine is a straight grate which employs updraft drying and cooling and downdraft drying, preheat and firing. It is necessary to regrind the concentrate before pelletizing. The con-centrate is 60% passing 325 mesh, with a surface area of ±lOOO cm2/Gm, and must be ground to about 83% passing 325 mesh, 1600 cm2/Gm blaine surface area, for pelletizing. The energy for regrind has been reduced from 12.5 KW per LT to 8.80 KW ate of 2.0 million per LT. This was the result of changes made in the concentrator where originally a coarse spiral concentrate, instead of the magnetic concentrate which is screened on fine screens to reduce the coarse fraction and prevent overgrinding before flotation, was produced. Also in 1968 an additional concentrating line was added to the concentrator which employs more grinding power than the other three lines. The demand for a high iron grade and lower silica pellet resulted in the investigation of different schemes of upgrading the reground concentrate which had more iron values liberated during grinding for surface area. The reagentized material presented many problems, mainly in selectivity trying to flot the iron and with high reagent consumption having to dereagentize the concentrate for amine silica flotation, in the various flotation systems tried. Tests were then conducted with elutriation (2) which proved satisfactory by removing the lower specific gravity, fine gangue material from the heavier material with the

Jan 1, 1977

By M. A. Chandler, G. T. Adel, J. N. Richardson, E. C. Gutierrez

A rapid, bench-top analyzer has been developed to determine P2O5 content and CaO/P2O5 ratio in phosphate ores. The analyzer utilizes a portable computer equipped with a frame grabber to measure the reflective intensity (gray level) of phosphate samples placed in front of a television camera. P2O5 content is related to the average gray level of the sample, while CaO/P2O5 ratio is determined from the amount of bright material present. The sensor is currently being used to analyze flotation concentrate samples at Texasgulf's phosphate operation near Aurora, North Carolina. Sensor development along with results from laboratory and in-plant testing are discussed.

Jan 1, 1993

By N/A

finally, but not least, the staff of Vaal Reefs Chemical Laboratory for their assistance and patience with the introduction of a new technology,

Jan 1, 1991

By S. D. Thompson, L. Adler

This study reviews and analyzes the empirical methods available for designing the capacities of coal mine gathering belts. The analyses lead to recommendations concerning the application and implementation of each empirical method. Operations research techniques, mainly simulation models, are also briefly mentioned, and a few recommendations are made concerning their selection and application. The objective of the study is to provide a reliable basis for the practicing engineer to properly select, apply, and implement a capacity design method.

Jan 1, 1988

By A. A. Campoli

A stress control design strategy was developed to minimize the explosive failure of highly stressed pillars, during room-and-pillar retreat mining conducted between stiff immediate roof-and-floor strata. A confined core coal pillar strength model was based on in-mine geotechnical evaluations of successful room-and-pillar and longwall bump control designs. Tributary area and linear shear angle approaches were used to estimate development and gob side abutment pillar loads for supercritical section widths. Subcritical width sections separated by barrier pillars to control stress within total extraction panels were optimized with the boundary element program MULSIM/NL.

Jan 1, 1994

By Ralph E. Magnuson

The quality of our environment is of great importance to all of us. Today, there is a great public concern about the degradation of our air, land, and water and the resultant slow death of our planet Earth. The miner has always been concerned with his environment. Historically, mining has been a part of the frontier. As a result, the miner has pioneered and developed many parts of the world. In the beginning, he had to hack out a place for his mine, himself, and his family. He was given accolades and praise for his accomplishments. Now, however, he is attacked as a ravager of the landscape. It was and is no different on the Marquette Iron Range in Marquette County, located in the Upper Peninsula of Michigan. Iron ore was discovered in 1845 and mining was begun by 1848. Over nearly 1 ¼ centuries, a total of 379,197,000 tons have been shipped to market. Ports, docks, railroads, and towns all had to be built in order to get that tonnage out to iron and steel makers. In those early days the environment had to be mastered, not pampered.

Jan 1, 1970

By George M. Meisel

This paper is devoted to a discussion of the factors governing design of concentrators for large grinding circuits. Emphasis is placed on the manner in which use of ever larger grinding mills has affected the size of grinding bays, service cranes, gear reducers and electric motors, and the selection of ancillary equipment for cushioning of the starting load of large mills. Information is presented on the effect of using large grinding mills on the capital and operating costs of concentrators, e. g. : (Fig. 1) ? Benefits in lower cost of mills, drives and materials handling equipment, plant space, power, grinding media, operating labor and maintenance, and in ease of instrumentation and automation. ? Penalties in distribution of materials from the grinding mills to multiple lines of equipment which have not been developed to commensurately large sizes, and higher cost of ancillary equipment.

Jan 1, 1968

By Steve Wirch, Robert Jankowski

The issue of dust control in underground coal mines has been extensively studied by both government and industry. This research work has resulted in many techniques which control the dust or help miners avoid it. Control techniques either prevent the dust from becoming airborne or cleanse the air before it can be inhaled. Avoidance measures minimize the exposure of miners to the airborne dust by blowing the dust away from work areas or making it unnecessary for a miner to occupy a dusty region. One of several successful dust control measures in continuous miner sections is the use of a machine mounted scrubber which cleanses the air and helps to prevent the contaminated air from reaching areas frequented by mine personnel. Research on the application of scrubbers on longwall shearers began in the 1970s and continued into the 1980s. The most successful projects showed only moderate improvement when a scrubber system was mounted on a longwall shearer, and the less successful projects actually increased worker dust levels. There are many reasons that scrubbers have not been successfully applied on longwalls. The most significant of these is that longwalls have across the face ventilation and generally have high face air flows. Scrubbers tend to work best when they are the primary cause of ventilation. Therefore, their capture efficiencies on longwalls tend to suffer because of the exposure of the drums to the primary airflow. Other reasons scrubbers have not been implemented on longwall s include the successful application of an excellent water spray system, effective cutting techniques, and dispersion of dust sources. These techniques can help control drum generated dust, increase production, and limit the relative effectiveness of a scrubber.

Jan 1, 1995

By R. K. Steinhorst

Multivariate cluster analysis, MANOVA, canonical analysis, and discriminant analysis of hydrochemistry data were used to investigate the directions of ground water movement in basalts in the vicinity of the Hanford Reservation, Washington. The statistical analyses indicate that the hydrochemistry of the ground waters in these basalt formations is distinctly different on each side of the Columbia River. This suggests that the river is a ground water divide or that the river is roughly coincident with a hydrogeologic barrier boundary. The statistical procedures used in this study constitute a quantitative means for differentiating ground waters according to hydrochemistry.

Jan 1, 1990

By D. Randall Crooke, Ron R. Jorgenson

Many coal combustion products (CCPs) have historically been unsuitable for placement as mine backfill because of their physical and geochemical properties and/or regulatory status. However, innovations in paste production and transport of CCPs utilizing the high, fine particle contents of these fine-grained waste materials and their water retention colloidal properties produce a non-segregating, self-cementing material that may be environmentally suitable for placement as mine backfill. Both industry and the regulatory agencies are enthused by the possible cost reductions, both in design and construction of disposal sites, and the reduced environmental impacts of CCP realized by implementation of this new use/disposal technology.

Jan 1, 2001

By Peter Ralph

All copper ore haulage at Isamine was transferred to the new 19 level haulage network by mid 1975. Previous experience together with design studies had indicated that a three train operation would be required to haul the scheduled ore production. The ore train with a gross weight of 600 tonne is made up of 15 bottom dumping trucks hauled by twin electric locomotives (Figure 1). Present train speeds reach 40 km/hr and, in the future, this speed could be increased to 55 km/hr. The planned operation on the restricted track network and the relatively high train speed meant that the train driver operated block light system would be inadequate on the grounds of haulage safety and meeting production targets. Some form of Centralised Train Control (CTC) system emerged as a necessity, and as an initial step, tenders were called for a relay control type CTC system. The high cost of these systems and the anticipated high maintenance costs and inflexibility of the offered systems led to the rejection of the tenders. It was decided to develop a CTC system locally and to use a digital computer to perform the basic track [ ] equipment interlocking tasks and monitor haulage operation.

Jan 1, 1979

By E. H. Cho

Pittsburgh #8 coal cleaned by the conventional froth flotation was oxidized in a 2-liter Parr Stirred Top Bench Reactor. The oxidation time was varied up to 5 hours; the temperature, from 150 to 225°C, the oxygen pressure, from 15 to 500 psi; and coal dosage, from 15 to 60 grams in 600 ml of distilled water. The oxidation of coal was evaluated by measuring total acidic group formed on the coal surface as well as by measuring the adsorption of calcium ion from a solution under standard conditions. It was found that the oxidation increased with increasing oxygen pressure without much leveling-off effect. However, the oxidation of coal increased sharply from 150°C to 175°C and then tended to level off above 175°C. The adsorption of calcium was reached more than 3% on the coal oxidized under favorable conditions. The adsorption of calcium on coal increased sharply with increasing equilibrium pH. The BTU loss was sensitive to oxidation temperature. This study concludes that the optimum oxidation of coal should be conducted at high oxygen pressures around (e.g. 500 psi) 170°C for 3 hours. This study also concludes that the oxidation in an autoclave is far superior to that in a fluidized bed in terms of calcium adsorption, BTU loss and reaction time.

Jan 1, 1994