Search Documents

By S. Jennings

The Red Dog massive sulfide deposit is located in the western Brooks Range of Alaska 100 miles north of the village of Kotzebue. It contains the largest zinc reserve in the world. Reserves were doubled in 1995 with the discovery of the Aqqaluk deposit and significantly increased in 1996, with the discovery of a deep zone of mineralization to the north. At present the global reserve and resource is 143 million tonnes of 16.1 % zinc and 4.3% lead. Red Dog is a silica + sulfide synsedimentary replacement deposit hosted in barite and black shale of the Mississippian Kuna Formation. Red Dog was thrust northward during the late Mesozoic Brookian orogeny. Understanding the setting of the deposit at the time of formation and its subsequent deformation history is critical to current exploration efforts and to future discoveries in the district.

Jan 1, 1998

By Charles R. Jenkins

Three sedimentation ponds had their performance evaluated before and after installation of modifications. Each pond had a floating baffle installed, two had siphon outlets and one had a floating outlet device. Baffles inhibited short circuiting, and the outlet devices retarded flow following a rainfall event, and drained the pond creating a large storage volume to maximize detention time. Total suspended solids and settleable solids tests were run on samples of influent and effluent to evaluate pond performance. Particle size analyses were run on samples containing measurable amounts of solids. Performance improved in each pond, with baffles providing the major improvement. Through the entire surface mining process un- protected soil is exposed to direct rainfall and subject to accelerated erosion. Without controls, receiving streams would be "choked" by the additional sediment load. Several states, including West Virginia, require that sediment control ponds be constructed to trap the sediment before the water enters receiving streams. Even well designed ponds have exhibited difficulty in meeting effluent limitations. In a study supported by EPA, about half the ponds did not meet effluent limitations (1). There is a critical need to reduce sediment losses using presediment pond controls or by improving sediment pond performance. The objectives of this study were to evaluate modifications designed to improve sediment pond performance by; 1) monitoring three ponds prior to modification, 2) install floating baffles and 3) modify the principle spillway and determine the change in pond performance.

Jan 1, 1985

By G. A. Hayes

The range of gold ores tested at AMMTEC LTD over several years has resulted in the requirement to analyse for the mode of occurrence of gold in order to assist selection of ore processing options. The aim of this paper is to describe the laboratory testwork and analytical procedures which have been of benefit in detail­ing the mode of occurrence and mineral associations of gold and hence being of value in developing an optimised ore processing route. The range of ore and mineral assemblages described include relatively simple pyrite and free milling ores, more complex pyrite plus arsenopyrite gold ores and the quite com­plex associations of gold in copper bearing ores or with car­bonaceous mixed sulphide ore assemblages. The aim of this paper is to describe the laboratory testwork and analytical procedures which have been of benefit in detail­ing the mode of occurrence and mineral associations of gold and hence being of value in developing an optimised ore processing route. The range of ore and mineral assemblages described include relatively simple pyrite and free milling ores, more complex pyrite plus arsenopyrite gold ores and the quite com­plex associations of gold in copper bearing ores or with car­bonaceous mixed sulphide ore assemblages.

Jan 1, 1996

By Paul W. Johnson

Chemical mining is the in situ extraction of metals from ores located within the confines of a mine (broken or fractured ore, stope fill, caved material, ores in permeable zones) or in dumps, prepared ore heaps, slag heaps, and tailing ponds on the surface. These materials represent an enormous, untapped, potential source of all types of metals. The field of chemical mining, now in its infancy, encompasses the preparation of ore for subsequent in-place leaching, the flow of solutions and ionic species through rock masses and within rock pores, the leaching of minerals with inexpensive and regenerable lixiviants under prevailing conditions of the in-place environment, the generation and regeneration of such solutions, and the recovery of metals or metal compounds from the metal-bearing liquors. It is not inconceivable that eventually our ore reserves will consist largely of low-grade, refractory, and inaccessible new deposits and low-grade zones near previously worked deposits, caved and gob-filled stopes, waste dumps, tailing ponds, and slag-heaps. Chemical mining promises economic recovery from these types of deposits. Before it can come of age, however, a much better understanding is needed concerning its chemical and physical aspects.

Jan 1, 1967

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"During the last ten years great strides have been made, on the Mesabi Range, in the practice of beneficiating low grade iron ore material. By .beneficiation is meant all methods of removing impurities, and raising the iron content to a point where it can be sold in open market, the principal impurities being silica and moisture. The • general processes to which low grade iron ores are amenable are as follows:1. Thermal(a) Drying ; removes hydroscopic or atmospheric moisture. .(b) Calcining; removes carbon dioxide from iron carbonate, molecular water from hydrated hematites, and atmospheric moisture.Roasting; removes sulphur, carbon dioxide, molecular water and atmospheric moisture.Agglomeration; primarily for the purpose of preparing finely divided material for blast furnace; briquetting and sintering.2. MechanicalScreen sizing; removes rock and sand.Classification; removes sand by means of currents of water of varying velocities.Log washing; removes fine sand.Jigging; removes larger particles of impurities than is possible by log washing. Certain types of jigs remove fine sand.Reciprocating tables; recover fine iron particles from sand discarded by above processes.Magnetic separation; applicable to the commercial separation of the magnetic oxide of iron from gangue material. From a scientific standpoint it is possible to separate certain hematites and limonites from their gangue:(g) Miscellaneous processes; comprise dry concentration, electro-static separation and other processes."

Jan 1, 1920

By Max Friedemann, Alexandros Bousdekis, Anna Gustafson, Helmut Mischo, Håkan Schunnesson

Many devices used in mining are not monitored by sensors or do not have their own intelligence. By retrofitting sensors and real-time data processing, machines can be integrated into an existing digital infrastructure. Within the project Mine.io funded by the European Union a Sandvik DE110 exploration drill rig is being digitized using various AI algorithms at research and education Mine “Forschungs- und Lehrbergwerk Reiche Zeche (FLB)” of TU Freiberg. The aim is to increase the productivity of drilling with real-time evaluation of the current rock to be drilled and the current maintenance status of the drill rig. The drill rig is equipped with a speed sensor, pressure sensors in the hydraulics, 3-axis vibration sensor, borehole length measurement and temperature sensor. The sensors are additionally attached to the drilling rig and no structural changes on the drill rig are necessary. All data are processed real-time at a server structure outside of the mine using AI algorithms to analyze which rock (ore or host rock) is being drilled and to perform predictive maintenance. Processed Data are visualized for the operator to optimize the workflow and the productivity.

Feb 1, 2025

By Christine E. Turner-Peterson

Pore-filling organic material concentrated uranium to form sandstone-hosted primary uranium deposits in the Jurassic Morrison Formation of the Grants uranium region, New Mexico. Petrographic observations and radiometric ages for primary ore in the Westwater Canyon Member require that the organic material was emplaced early in the diagenetic history of the host sandstone; in fact, organic material was emplaced before major compaction. This inferred early emplacement constrains models concerning the nature and origin of the organic material and thus also constrains models of ore genesis. Reconstruction of the burial history of the basin indicates that Late Jurassic-Early Cretaceous time, the interval of inferred emplacement of the organic material, was probably not a time of hydrocarbon generation and migration. Nuclear magnetic resonance analyses, elemental abundances, and isotopic studies provide further constraints on the nature of the organic material, and data from these studies are consistent with a humic acid rather than an oil origin. In addition, the overall tabular shape of primary uranium orebodies and the way these orebodies are suspended in the host sandstone mimics Recent deposits of humate, the precipitated form of humic acids. The critical clue that favors a humic acid origin for ore-related organic material is provided by the nature and patterns of postdepositional alterations that are spatially and temporally related to primary ore, specifically destruction of detrital magnetite and ilmenite (iron-titanium oxide) grains. Humic acids are implicated in the destruction of iron-titanium oxide grains because these organic acids are one of the most effective natural agents in leaching of Iron from these grains. Thus, timing constraints, chemical evidence, orebody geometry, and the nature and patterns of ore-related alterations favor a humic acid origin and suggest that an oil origin is highly unlikely. Because alteration of iron-titanium oxide grains tracks the pathways of humic-bearing solutions through the host sandstones, it is possible to trace these solutions back to their source. Alteration patterns in the Westwater Canyon Member suggest that the humic-bearing solutions originated as pore fluids in the mudflat facies of the overlying Brushy Basin Member and moved into adjacent sandstones during early dewatering of the mudstones. The humic acids precipitated, by the process of cation loading, in tabular layers. Uranium was concentrated within these tabular layers by complexation with the humic acids to form primary uranium orebodies.

Jan 1, 2013

By L. Alagha, O. Molatlhegi, S. Khatibi

"In the present study, the effect of organic/inorganic (hybrid) polyacrylamide polymer on fine coal flotation was investigated. Raw coal samples contain about 37% of ash-forming mineral at a feed size of -75 + 38 um were subjected to flotation tests in the presence of in-house synthesized hybrid Al(OH)3-PAM at different polymer dosages and pH values. Results show a significant improvement in both combustible recovery and ash rejection at 1 ppm polymer dosage. Further improvement of combustible recovery was obtained when flotation was performed at pH 5. Interfacial properties of coal particles before and after flotation were examined through electrokinetic (zeta potential) measurements of coal/water slurries. Zeta potential vs. pH curve were established and compared. In the case of raw coal/water slurry, zeta potential-pH curve resembles the ash-forming minerals (silica and clays) more than coal. After Al(OH)3-PAM-assisted flotation, the zeta potential of froth/water slurry shifted to more positive values point which strongly indicates significant removal of ash-forming minerals from coal by Al(OH)3-PAM. INTRODUCTION Coal has been a major commodity in meeting the world energy demand during the past several decades (Milici et al., 2013). According to the international energy agency, global coal demand will continue to increase for the coming decades. With increasing world population, the global electricity demand would also increase as more people would get access to basic electricity especially in developing countries (Maggio & Cacciola, 2012). Due to this increase in energy consumption, operations in coal mining and beneficiation processes have been highly mechanized to meet the demands. This mechanization has increased the quantity of raw fine coal particles produced which contain high amount of ash-forming mineral matter (slimes). Aplan et al., have reported that the major constituents of ash-forming minerals in U.S.A coal are clay minerals such as kaolinite, montmorillonite and illite (Aplan, 1997). Conventional froth flotation for fine coal cleaning suffers mainly from two major problems: 1) Low recovery of ultrafine coal particles due to slime coating by ash-forming minerals, and 2) The lack of selectivity, which results in the flotation of middlings and entrainment of mineral fines in the froth (Polat et al., 2003). Slime coating on both valuable and air bubbles have been proposed to explain the observed reduction in flotation recovery especially when fine grinding is required. In this case mineral matter may be degraded to extremely fine or colloidal sizes thereby creating difficulty in the water clarification process such as flotation. Slimes inhibit bubble-particle attachment, and increases reagent consumption due to the increase in solid/liquid interfacial area, resulting in low coal recovery."

Jan 1, 2015

By Colleen A. M. Gibbs

On July 30, 1979 New Council on Environmental Quality (CEQ) regulations for implementing the procedural provisions of the decade-old National Environmental Policy Act went into effect. These new regulations replace approximately seventy different sets of agency regulations, providing some uniformity throughout the Federal government in the conduct of environmental reviews and preparation of environmental impact statements (EIS). This attempt by the Federal government at a general improvement in the preparation and quality of EIS's presents an opportunity for the mining industry to evaluate how the EIS process for mining proposals can be expedited. The environmental impact statement is often a key element on the critical path of a major mining project. Preparation of the EIS is ordinarily the responsibility of the Federal agency with primary decision-making authority over the project. Still, the proponent, i.e. the mining company, can play a major role in the process and have a major impact on the timeliness and adequacy of the effort. Typically, the Proponent will conduct (or will hire consultants to conduct) environmental baseline studies of, for example, air quality, wildlife, geology, water quality, vegetation and archaeology. These studies are then compiled into an environmental report and submitted to the agency. The agency verifies the data and incorporates them into the environmental impact statement.

Jan 1, 1979

By A. S. Ibrado, D. W. Fuerstenau

"Gold, silver and copper form various complexes with cyanide, of which only the singly charged dicyano form adsorbs appreciably on activated carbon. The adsorption of the dicyano complexes appears to be controlled predominantly by chemical reaction at the surface of a shrinking unreacted core. Metal uptake over time is non-linear, which eliminates control by boundary layer diffusion. The rate of adsorption is not enhanced by a reaction interruption, which suggests the absence of concentration gradients in the pores. Finally, the rate of adsorption increases with decreasing activated carbon size in a manner consistent with the shrinking core model. The results of this investigation accentuate the importance of efficient acid washing of carbon and removing carbon fines from the barren carbon stream. INTRODUCTION With the dwindling reserves of high-grade ores, most of the world’s gold is produced from low-grade ores by cyanide leaching. In the past, leaching was followed by the Merrill-Crowe process, in which gold is precipitated from clarified pregnant solutions by zinc cementation. This process is still being used for high-silver ores, where the cost of carbon stripping becomes prohibitive. For deposits with silver-to-gold ratios of about 4 or less, adsorption on activated carbon would be the usual solution purification step taken. The process simplifies solid-liquid separation and offers a viable solution to preg-robbing organic carbon in some ores. The modern industrial application of carbon adsorption started with the carbon-in-pulp (CIP) process, where carbon adsorption was used mainly as a solution purification step. In 1973, Homestake Mining Company commissioned the first large-scale CIP plant in the U.S.A.1 Later, carbon was added earlier in the circuit to control preg-robbing by adsorbing gold cyanide onto activated carbon as soon as it is dissolved. The scheme is successful because activated carbon is a stronger adsorber than the organic carbon found in preg-robbing ores. This process came to be known as the carbon-in-leach (CIL) process. Numerous research investigations have been performed on the chemistry involved in the CIP process, which at the time of its introduction was not clearly understood. Of these, research on the kinetics of adsorption probably bears the most immediate impact on industrial practice,2,3 where adsorption systems rarely reach equilibrium, if at all, and slight slowdowns in the adsorption rate can translate into significant decreases in revenue. To illustrate this, organic compounds, like flotation reagents, have been known to impair CIP circuits. However, laboratory tests showed that the organic compounds do not significantly affect the adsorption capacity of activated carbon. Rather, the harmful effect may be attributed to a lowered adsorption rate.4,5 Also well known is the faster rate at which fine activated carbon powders reach equilibrium compared to coarse activated carbon, even though the final (equilibrium) amount of material adsorbed per unit weight is the same."

Jan 1, 2015

By S. Shankar

Available literature on the effect of re-entrainment on overall airborne dust concentration in mine airways or the fundamental mechanisms of coal dust re-entrainment in mine atmosphere is scant. Therefore, as part of the Respirable Dust Center's ongoing research, a three part study was envisaged: study of the re-entrainment phenomena of anthracite and bituminous coal dust particles in a wind tunnel under the influence of varying air velocities; study of the same in the Lake Lynn Laboratory Mine of the USBM with both airflow and walking by personnel causing re-entrainment; and mathematical modeling and computer simulation of the re-entrainment phenomenon. In this paper, results from the re-entrainment studies in the wind tunnel and the Lake Lynn Laboratory Mine are presented. Further, the results from the wind tunnel studies are compared with the results from in-mine studies conducted at the Lake Lynn Laboratory Mine of the USBM. Comparing the results from the two studies it was observed that increasing air velocity increased the rate of re-entrainment, but increased time of exposure decreased the airborne dust concentration. Compared to same size particles, a mixture of sizes created more airborne dust concentration when re-entrained. It was also observed that contribution of airborne dust concentration due to airflow was negligible compared to the contribution due to walking.

Jan 1, 1995

By Ronald B. DeDiemar

It is generally held that cone crusher application technology is strictly an art and thus subject to the vagaries of emphirical and/or trial and error judgments. While this is basically true, certain factors have been identified which, when properly defined, can significantly reduce the element of chance. This paper will bring out these factors as well as pointing out other technologies available to predict and/or analyze cone crusher performance.

Jan 1, 1977

By Carlos Fonseca, Gustavo Usero, Roberto Mentzingen Rolo, Gabriel Moreira, Octavio Rosa de Almeida Guimarães

Geological domain modeling is an important step in mineral resources evaluation. The procedure can be laborious and time-consuming, especially in multivariate settings. However, estimates are significantly improved when carefully limited by geological variables. This paper proposes a workflow for geological domain modeling suited for stratigraphic deposits. The workflow consists in automatically defining the domains by using clustering algorithms, generating the surfaces that represent the contacts by interpolation and subsequent triangulation, and simulating the surfaces. The proposed workflow produces consistent and realistic results and allows the user to test different domain configurations and assess volumetric uncertainty automatically and quickly.

Jun 25, 2023

By G. Almgren

With the exception of sublevel caving, the most common method of underground mining in Sweden is the "cut-and-fill" method. It is normally used for mining non-ferrous metals , and' is used extensively in the complex sulfide ore mines of the Boliden Company in north and central Sweden as well as the mines of the STORA and Vieille Montagne Companies in central Sweden. All in all, the cut-and-fill method is used in 13 of Sweden's 45 mines. As the mines are relatively small, the volume of ore mined by this method represents only about 5 % of the total ore production in Sweden. The commercial value, however, is much large than this percentage would imply. The production volumes and grades of some typical mines are shown in Table I. As seen, when rated internationally, the grades are comparatively low. The prices are set according to ?international metal prices? as dictated by the London stock exchange, and in lieu of governmental support, rational management methods are critical in order to achieve satisfactory profit.

Jan 1, 1975

By Y. V. Vasylchuk

This paper presents an algorithm for optimizing the classification of surface mine material subject to excavating constraints. High-resolution expected profit models are input and optimized to classification maps subject to site-specific rectangular excavating constraints. This optimization problem defies traditional closed-form analytical solutions; a practical heuristic algorithm has been developed to quickly determine the optimal final destination for the material subject to realistic constraints. The optimization is fast and generates results that achieve up to 98–99% of the total expected profit achieved with free selection. This algorithm provides a fast viable option for practical application in short-term grade control and in managing multiple realizations in long-term resource estimation.

By A. A. Jonke

The combustion of fossil fuels in a fluidized bed of calcined limestone particles is a potentially efficient and economically attractive process for the generation of steam for electric power production and other uses. The process results in greatly reduced emissions of both sulfur oxide and nitrogen oxide pollutants. Development work, evaluations and design studies are being carried out by various organizations under contract with the U. S. Environmental Protection Agency and the Dept. of Interior (Office of Coal Research). The AEC's Argonne National Laboratory is one of the principal participants in the development program under interagency agreements with EPA and OCR. This paper covers the principal reasons for developing fluidized-bed combustion, its advantages and disadvantages over conventional combustion methods, and some of the potential applications of the process. The participants in the multi-organizational program, the sponsoring agencies, the general status of development of the overall project, and the chief program areas that still require resolution are discussed. The main features of the program of work at Argonne National Laboratory and the results achieved so far are also included.

Jan 1, 1974

By Ross A. Scarano

It wasn't until late 1976 that the U. S. Nuclear Regulatory Commission (NRC) set about to address the uranium tailings issue in earnest. It was decided that a generic environmental impact statement related to uranium milling operations would be prepared to support formal tailings regulation. We recognized, however, that this was a task that would take many years to complete and we could not take a "business as usual" approach to tailings management in the interim; the issue was too sensitive. To facilitate licensing during the interim period, the NRC developed guidelines in May 1977, for the industry in the form of the following performance objectives for tailings management: Siting and Design 1. Locate the tailings isolation area remote from people such that population exposures would be reduced to the maximum extent reasonably achievable. 2. Locate the tailings isolation area such that disruption and dispersion by natural forces is eliminated or reduced to the maximum extent reasonably achievable. 3. Design the isolation area such that seepage of toxic materials into the groundwater system would be eliminated or reduced to the maximum extent reasonably achievable. During Operations 4. Eliminate the blowing of tailings to unrestricted areas during normal operating conditions. Post Reclamation 5. Reduce direct gamma radiation from the impoundment area to essentially background. 6. Reduce the radon emanation rate from the impoundment area to about twice the emanation rate in the surrounding environs. 7. Eliminate the need for an ongoing monitoring and maintenance program following successful reclamation plan. 8. Provide surety arrangements to assure that sufficient funds are available to complete the full reclamation plan.

Jan 1, 1980

By Joe D. Mitzel

The Indian Head fine has been in existence since 1922. For over 56 years there have been North Dakota people mining coal at this same location. The area affected will fit inside a circle 5 km in diameter, and the coal is lignite. The seam thickness has varied from 2.4 m to 3.65m, and the overburden from 6 m to 30 m in depth. me Lignite coal which is being mined at the Indian Head Mine is from 15.8 x l0 6 to 16.7 x 10 6 J per kg; it has a moisture content of 33 to 38%; an ash content of 5 to 10%; and a sulfur content of from 0.5 to 0.7%. The moisture content and the fact that we crush the coal co a top size of 14 cm x 0, are two of the characteristics or the product which cause it to freeze and remain inside of the railroad cars on the slope sheets. The market for the coal initially was almost entirely local coal sales. That is, coal was sold to people in the area who used the lignite to heat their homes, stores, offices, schools, and churches. Back in the early 1920's, there were no stoker-fed boilers, or pulverized fuel boilers, as we have in today?s marketplace. Basically, all of the coal was sold as lump coal, pieces about 30 to 35 cm square, to be used in furnaces: and nut coal with a top size of about 7.5 cm to 10 cm to be used in the old kitchen cookstove. All of the coal fines, less than 5 cm, were screened out and layed onto a pile. There was no market for the smaller sizes of the lignite coal. It has been our experience that when the coal is in lumps or chunks larger than 7.5 cm to 10 cm, there is a very slight possibility of freezing. That is the chunks themselves freeze, but by their nature, they do not cling to one another or form large masses of frozen material which are difficult to remove from the slope sheers of the railroad cars.

Jan 1, 1980

By Halter L. Gould

Since the turn of the century there has been a marked increase in population, industrial and economic growth, and in energy requirements in the United States. During this time our energy needs have been met largely by natural gas and petroleum, but as our reserves of these materials are depleted, we are going to depend more and more on our large reserves of coal. The mining of coal for electrical power production has increased at a rapid rate during the past decade. Over half the coal produced in the United States in 1971 came from mines utilizing surface mining operations (Paone, et al, 1974). Surface mining is expected to increase as the rising cost of oil places more demand on coal for energy. About 57 percent of the coal reserves in the United States lie in the area west of the 100th meridian. About one-quarter of this can be mined by current surface methods. This would involve the disturbance of approximately 1.5 million acres (600,000 hectares). By the year 2000, projections indicate disturbance of about 200,000 acres, or 300 square miles, in the West. Mined areas receiving more than 250 mm of annual precipitation can usually be revegetated without irrigation if the spoils are properly shaped, the surface layer consists of suitable plant growth media, and proven techniques in rehabilitating disturbed rangeland are applied. Areas receiving less than 250 mm of annual rainfall or with high evapotranspiration rates pose a more difficult problem. Revegetation of these areas can probably be accomplished only with major inputs of water and good management (National Academy of Science, 1974).

Jan 1, 1978

By Mike Ghassemi

It is clear that precise overground and under-ground mapping is an important factor for all designers. Due to rapid changes in underground construction, tunnel designers are increasingly in need of updating project information. This article explains the latest techniques for detecting under-ground utilities as well as underground mapping. Global Positioning System (GPS) is a very ac-curate and popular navigation and mapping system that has been used extensively above ground, but is not used for underground mapping as signals are not strong enough to pass through ground or water. Most underground techniques were developed for military applications during the first and second world wars. Later, the techniques became public. For example, ground penetrating radar was developed for the military in 1970 to be used for locating tunnels under the demilitarized zone between North and South Korea. Later, the same technique was used for detecting unexploded ordinance such as plastic land mines.

Jan 1, 2011