Search Documents

By H. Akgun

Design of plugs for abandonment of boreholes and shafts may be governed by the bond strength between the plug and host rock. This paper presents the results of push-out tests on cement grout plugs in salt. Two expandable cement grouts have been tested. The average interface shear strengths ranged from 2 to 12 MPa. Peak shear stresses at failure, assuming an elastic stress distribution along the interface, were up to eight times higher. Standard deviations commonly reached 20%. Dissolution along the interface was observed, and may have been enhanced by clay inclusions in the salt. This dissolution appears to have reduced bond strengths. Application of the results to the design of plugs for larger openings (e.g. shafts, drifts, or boreholes) is discussed.

Jan 1, 1991

By Richard G. Almes

Since the failure of a major coal refuse disposal embankment and impoundment in the Buffalo Creek watershed near Man, West Virginia in early 1972, there have been extensive changes in the design and construction requirements for coal refuse disposal facilities located throughout the United States. The primary emphasis has been on improving the safety of these facilities, particularly for impoundments which are capable of storing millions of gallons of process water and storm runoff. The Mine Safety and Health Administration (MSHA) of the U.S. Department of Labor (formerly the Mining Enforcement and Safety Administration, U.S. Department of interior) has been the lead federal agency in promulgating regulations pertaining to coal waste disposal. In 1974 and 1975, studies were undertaken by our firm under contract to the Mining Enforcement and Safety Administration to prepare a comprehensive engineering and design manual to be used by operators and engineers in the planning and design of coal refuse disposal facilities with the intent ion of avoiding any more Buffalo Creek failures. The resultant 800-page document addresses major subjects such as safety, environmental controls, and cost. Specific topics include characterization of coal refuse, classification of disposal facilities, project planning, geotechnical investigations, testing and design requirements, hydraulic and hydrologic design, environmental factors, operations, and monitoring, instrumentation, and maintenance.

Jan 1, 1980

Mill #4 processes mildly refractory ore from Carlin Trend deposits. Diagnostic analysis of plant operating data was used to generate a mathematical model containing the important parameters influencing gold recovery. The model was used to direct modifications to plant operating practice. The cyanide-dosing strategy was changed to reduce gold losses from preg-robbing and to cut reagent consumption. A finer grind was achieved without capital investment. The density in the carbon-in-leach circuit was lowered, and tighter control was exercised over the plant throughput. These changes resulted in a recovery increase of at least 2%, worth $111,000/month at $300/oz ($9.64/g) gold, and concomitant reagent cost savings of $55,000/ month.

Jan 1, 2000

By J. C. Heter

Industrial Mineral Fillers, LLC. is in the initial stages of mining and processing Anorthosite (CASPAR TM) at its CASPAR mine located in Soledad Canyon, Los Angeles County, California The CASPAR is being mined from the Precambrian San Gabriel Anorthosite Complex of the western San Gabriel Mountains. Preliminary results suggest that CASPAR is a desirable alternative to silica sand used in construction applications, such as, stucco, grout, abrasives, and other uses including filtration and golf course recreation sands. With the use of standard ore dressing techniques, CASPAR is suitable for use as a filler in paint, plastics and rubber. Environmentally, CASPAR has advantages over silica sand, in that, there is no detectable Free Silca.

Jan 1, 1997

By M. Kuchta

A linear integer programming (MIP) model to solve the long-and short-term production-scheduling problem for sublevel caving operations is presented. The MIP model is designed as a multi-time-period problem to provide monthly schedules that meet production, blending and sequencing requirements. One of the most important issues during the development of the MIP model was the requirement of sequencing between blocks. In this mathematical model, unique constraints that ensure sequencing of the production from sublevels are developed. A suggested method of handling a large number of variables is also given. The MIP scheduling model was implemented on a data set obtained from the Kiruna Iron Ore Mine located in northern Sweden. The initial MIP model implementation was successful and provided a solution that optimized resource recovery while meeting monthly and yearly production constraints. The scheduling results obtained based on the Kiruna Mine are further presented and discussed.

Jan 1, 2003

By Gill Montgomery

Although fluorspar is considered an industrial mineral by usage and value, its geological occurrence and the mining and milling methods employed make it more akin to the non-ferrous metal ores. Likewise methods of exploration for it are more like those used in the search for lead and zinc, with which fluorspar is often mixed. In fact, it often takes the mixture of fluorspar, lead, zinc, plus maybe barite to add up to enough recoverable values to make the mineral an ore by definition. This is so true where the fluorspar portion is low grade, perhaps less than 25 percent. Until the development of modern steel milling in World War I times, the invention of aluminum smelting, and development of the fluorine chemical industry and air conditioning, there were few uses for fluorspar aside from ceramic fluxes in the flint glass industry and for uses as glazes for pottery and china. Pure fluorite crystals have long been admired as semi-precious and ornamental minerals of many delicate colors.

Jan 1, 1983

By John F. Burst

For several generations now, the high alumina clayey sediments of Southeastern Alabama and Southwestern Georgia have supplied those regions with steady, mineral-based income although the impact of that income has been relatively minor until recently. Since World War II, mining activity has increased algebraically with over half of the total ore value in the Alabama area having been recovered since that time. The Georgia area production increases are even more dramatic. The trends are continuing and the next decade should see ore winning figures which will dwarf all previous production. It's time for the mining engineers to take note of this development as the mining methods, similar to the production, have developed rapidly and now offer challenges for the most competent professional. The development of mining techniques has followed a classic pattern. Beginning almost a hundred years or so ago, with the loading of weather-resistant surface boulders into mule-drawn wagons, mining methods have progressed to discovery of limited surface exposures in outcrop and eventually to stripping and development of non-obvious, subsurface deposits. Little by little, the overburden thickness of new pits has increased until, at present, pits with 100' -125' of overburden are being actively worked. Ground water problems in the Eufaula District are particularly challenging. At A. P. Green's J. W. Baker Pit, #l, in Barbour Co., Alabama, it is necessary to continually pump groundwater at the rate of about 400 gallons per minute from wells on the periphery of this large pit in order to keep the water table low enough to allow mining of the ore body.

Jan 1, 1972

By Conrad W. Steller

What is the definition of a successful construction or development project? It could be described in many ways: a project that performs as designed; a project completed on time, a project completed within budget. The title of our talk today is, "The Advantages of Applying Design/Build -Construction Management to the Mining Industry." As our talk develops, you will see that rather than tell you how to apply this concept, we will discuss the advantages and details of Design/Build so that you can independently apply the concept. Design/Build is not new, and it cannot be universally applied. It has, however, within the past ten years, carved a specific and substantial place in the overall construction -development market. The reasons for its rather recent rise to considerable prominence as a concept is due, in part, to the increasing urgency of gaining productive access of a production facility and, in part, to the inherent advantages of the concept's economics--and they are considerable. If the Design/Build concept of contracting were fully understood, it would, without exception, be the favored way for private industry to contract for its new construction and development as well as renovation work. The basic advantages are: earliest possible access and completion at the lowest cost. Design/Build is often equated and compared to "fast track" or "turnkey" methods of construction. The Design/Build concept can, in fact, be both of these or neither. "Fast track", in and 6f itself, implies that the project will be phased construction, that is to say, it will be built quickly; whereas I "turnkey" is a measure of the completeness of the project, usually meaning essentially that the

Jan 1, 1977

By Derek J. Barratt

The existence of a critical size buildup in an autogenous or SAG mill can be predicted from proper examination of drill core and ore samples. Methods of dealing with such critical size in a primary mill are reviewed in the context of ore properties, whether or not pilot plant-scale testwork has been conducted, and also with respect to the design of new plants or the retrofitting of existing operations. The implications of not planning for pebble crushing in situations where it is appropriate are discussed.

Jan 1, 1992

By C. J. Bise

In August, 1977, the Federal Surface Mining Control and Reclamation Act was signed into law [I]. It stated that: "The Congress finds and declares that because of the diversity in terrain ... and other physical conditions in areas subject to min ing operations, the primary governmental res- ponsibility for developing, authorizing, issuing, and enforcing regulations for-surface mining and reclamation operations subject to the Act should rest with the States." Section 516 of Title V (Control of the Environ mental Impacts of Surface Coal Mining) of the Act deals with the surface effects of underground coal mining operations. "Each permit issued under any approved State or Federal program pursuant to this Act and relating to underground coal mining shall re quire tfieoperator to adopt izeasures consist ent with known technology in order to prevent subsidence, causing material damage, to the extent technologically and economically feasible, maximize mine stability, and main tain the value and reasonable foreseeable use of such surface lands, except in those instances vhere the mining technology used requires planned subsidence in a predictable and controlled manner: Provided, that nothing in this subsection shall be construed to prohibit the standard method of room and pillar mining. "

Jan 1, 1980

By L Usoni

Collectors commonly used in flotation to date fall into two main classes: ionic and nonionic. The use of neutral or oily collectors is generally limited to the flotation of nonpolar minerals onto which they are adsorbed by forces of a physical or 'Van der Waals' type, while ionizable chemical collectors are utilized for all other types of minerals, adsorption in this case involving bonds essentially of a chemical nature. Though chemical adsorption is more selective than physical adsorption, even heteropolar collectors are active towards certain classes of minerals (sulphides for example) rather than towards one individual mineral. Thus, in order to float a given mineral from a mixture of minerals belonging to the same class, modifiers have to be used to render the action of the collector more specific. However, there are often considerable difficulties involved in this procedure and the desired results are not always attained, especially in the case of minerals of complex composition whose surface properties are not sufficiently well known. Hence the importance of seeking out collectors capable of linking selectively with given minerals. Selective linkage is possible if the collector structure incorporates active groups having specific affinity for certain cations characteristic of the mineral surface. The decision to investigate the possibility of utilizing chelate--forming reagents for flotation was based on the premise that phenomena which occur in solution and involve chemical reactions in the strict sense of the meaning and those which occur on the surface are closely correlated (1)

Jan 1, 1971

By Jeffrey J. Daniels

Advances in borehole geophysical research for mineral assaying, and remote detection of mineralization away from the borehole. Nuclear activation measurement research has provided accurate in situ assays of economic metals with neutron-gamma activation, using a high resolution intrinsic-germanium detector. Although nuclear activation analysis is the present "best-hope" for obtaining in situ assays for some elements, gamma-gamma and magnetic susceptibility measurements can provide accurate assays for lead-zinc and magnetite, respectively. Borehole optical spectroscopy and x-ray fluorescence are being investigated as possible in situ assaying techniques for some minerals. More laboratory and field calibration research is needed before nonlinear complex resistivity (NLCR) can be routinely used as a quantitative assaying tool. Field tests have shown that variations in the local geologic environment can affect the quantitative accuracy of assay values from downhole NLCR measurements. Deeply penetrating borehole geophysical methods are increasingly being used for mineral exploration as drilling costs and exploration have increased. Borehole electrical measurements have been shown to be useful for detecting conductive orebodies that are not interesected by a drillhole. Hole-to-surface resistivity, and surface-to-hole time-domain electromagnetics are demonstrated to be particularly effective for defining mineralized zones in a massive sulfide environment. Borehole gravity meters and three-component magnetometers have been developed and should prove useful for defining geologic anomalies away from the drillhole.

Jan 1, 1985

By A. Bascetin

Materials produced in quarries have been used for different intentions such as concrete and cement raw material, asphalt and embankment aggregates, railway ballast. Especially in cement manufacturing, the chemical composition and the uniformity of the raw materials play a strategic role in the economy and quality of the cement process. Therefore, it is necessary to achieve uniformity and desired chemical composition and maintain these at all production stages according to the type of cement produced. To achieve this goal the production planning and pit design play an essential role. This paper briefly outlines the production optimization of cement raw materials in a quarry in Istanbul western part of Turkey. For the purpose it was used the 3D ore body modeling and the geostatistical techniques. The variation of chemical components (%CaO, %Al2O3, %Fe2O3 etc.) and quality control parametres (LSF, SR, AR and etc.) obtained from the quarry were determined. Then the values of unknown chemical components and quality control parameters in the ore body were estimated using Kriging which is one of the geostatistical interpolation methods. The open pit design was also created by specifying wall slopes and taking into consideration of the grade distributions of the benches. The most important revolution in the paper is investigating the effects of the block dimensions in block modelling which is important for reserve estimation. The other important point in the study is using the different range values in variogram analysis for determination optimal reserve estimation. n this study, the effects of two parametres on reserve and waste amount estimation were determined according to CaO% distribution. The study was pointed out that the changing of the two parameters are very important for the optimal mine planning and environmental considerations.

Jan 1, 2010

By Yongjun Xian

The release of fluid inclusions has a strong potential for the unintentional activation of pyrite during flotation. The present study aims to characterize fluid inclusions in a natural pure pyrite. The results indicate that a certain amount of fluid inclusions exist in the pyrite. The fluid inclusions assume a variety of shapes, including long strips, oval shapes and irregular shapes, with sizes that range from a few microns to dozens of microns. From the EDS results of hollow positions that resulted from the fracture of the fluid inclusions on the pyrite surface, certain amounts of Al, Cr, C, O, Ag and Cu were clearly detected; these elements were not detected in FeS2 pyrite itself. The contents of the inclusions were released into solution when the sample was subjected to a grinding process. Under experimental conditions of 2 g of pyrite cleaned in 40 mL of pure deionized water under an inert atmosphere, the concentrations of Cu, Fe, Cl- and SO4 2- released from the inclusions reached concentrations of 3.29 × 10-6, 32.52 × 10-6, 51.57 × 10-6 and 75.90 × 10-6 mol/L, respectively. These values are significantly greater than those from the experimental nonoxidative and oxidative dissolution of the pyrite. The fluid inclusions of pyrite were, therefore, concluded to represent the dominant sources of Cu, Fe, Cl- and SO4 2- in the aqueous solution. The present investigation provides a new understanding of the source of the unavoidable metal ions in the pulp and may benefit understanding of the flotation theory and environmental geochemistry.

By Christopher Mark

Six decades ago, the most dangerous job in the USA was mining coal underground. Roof falls were responsible for half of the deaths, killing about 100 miners every year. Fast forward to 2016 and zero roof fall fatalities. Just three miners were killed by roof falls during the following 6 years. How did the mining community achieve this historic goal? This paper starts by analyzing the roof fall fatalities in 1968, categorizing them by their fundamental cause. Then, it shows how each type of roof fall was reduced over time, using snapshots of the fatalities occurring in subsequent decades. Along the way, it evaluates the influence of the regulatory environment, changing mining methods, and better ground control technology. The study found that in 1968 more than half of roof fall fatalities at large mines were attributable to an inadequate safety culture. The immediate effect of the 1969 Coal Mine Health and Safety Act was to reduce the riskiest activities, like needlessly going under unsupported roof. Other hazards, like large roof falls, required technological developments before they were brought under control. Roof Control Plans, which the US Bureau of Mines had been advocating since the 1920s, played a significant role throughout the process.

Mar 12, 2024

By Felicia F. Peng

The manganese removal from aqueous solution containing high Mn2+ concentration by adsorption and oxidation was studied using manganese oxide particles as the adsorbent. The operating parameters including pH, flow rate, initial manganese concentrations, and oxidant dosage affect the performance of Mn2+ removal were evaluated in a laboratory packed column. In the multi-column adsorption tests, each additional column doubled the time for complete manganese removal. No further decrease of pH was also observed once it was lowered to pH 4.5 to 5. This finding implied the possibility of complete high manganese removal without further pH adjustment during adsorption. Oxidation of Mn2+ by dissolved oxygen was found to be insignificant for manganese removal for high Mn2+ concentration. Adsorption was the predominated mechanism involved with manganese removal. Extremely low H+/Mn2+ stoichiometry compared to the reported values was measured. These low values suggested that different adsorption mechanisms such as chemisorption other than H+/Mn2+ ion exchange might play an important role at low pH. This paper presents the quantity and explanation of the results obtained for the mechanism of adsorption and oxidation of high concentration manganese on the manganese ore particles.

Jan 1, 1997

By J. B. Platt

Many utility fuel choices 1990-95 defied expectations, with utility decisions and coal market developments ever more closely linked. The Central Appalachian coal boom never occurred; clean-enough coal was developed in the hard-hit Midwest; Colorado-Utah coal surged; Pittsburgh seam production strengthened; utilities embraced Powder River Basin coal; and emission allowance prices collapsed. Competition drove productivity gains, but the future is not a simple repeat. Phase 2 brings fewer viable compliance options. Mega-railroad pricing has become a key risk factor --will this be countermanded by merging utilities and power market competition? Revenue losses from vintage contracts are problematic. Uncertainty also plagues natural gas, in spite of unanimity across major forecasts, since recent experience has been so heavily influenced by the gas bubble.

Jan 1, 1997

By Alden B. Carpenter

Brines (a solution containing more than 100,000 mg/l dissolved solids) in sedimentary basins are genetically related to evaporites in one of three ways: (1) dissolution of evaporite minerals, generally halite; (2) interstitial fluids in evaporites which are expelled from their source rock during compaction; (3) incongruent alteration of hydrous evaporite minerals (carnallite). Most brines of commercial interest originate as interstitial fluids in halite-rich rocks. These fluids are initially rich in magnesium, sulfate, and potassium but evolve in composition to an Na-Ca-Cl brine during their migration to their present host rock. A particularly important reaction in this process is: 2CaCO3 + Mgt+ = CaMg(CO3)2 + Cat (1a) This reaction reduces the magnesium content of the brine and ultimately converts it to a calcium-rich brine. The loss of sulfate occurs by two mechanisms. One of these is by direct precipitation as calcium sulfate (either as gypsum or anhydrite): Ca 2+ + SO4 2- = CaSO4 (2a) Additional sulfate may be lost from the brine by sulfate reduction: S042 + 1.33CH2 + 214- = H2S + 1.33CO2 + 1.33H20 (3a) The loss of carbonate species occurs by precipitation as carbonates: H2O + C02 + Cat = CaCO3 + 2H+ (4a) The net result of reactions 3 and 4 is: Ca 2+ + SO4 2- + 1.33CH2 = H2S + CaCO3 + 0.33H2O + 0.33CO2 (5a) The loss of potassium from brines is caused by the formation of potassium aluminosilicates: 2K+ + Al2Si2O5 (OH)4 + 4SiO2 = 2H + 2KAlSi2O8 + H2O (6a) The hydrogen ions produced by this reaction dissolve carbonates: 2H+ + CaCO3 = Ca 2+ + CO2 + H2O (7a) The net result of reactions 6 and 7 is: 2K+ + CaCO3 + Al2Si205 OH)4 + 4SiO2 = Ca2 + 2KA1Si3O8 + H2O + C02 (8a) A study of brines from central Mississippi has shown that the composition of these brines is related to the interaction of pore fluids from evaporites with minerals in the enclosing sedimentary rocks.

Jan 1, 1978

By J. Alatalo

Autogenous grinding is a process of reducing the particle size distribution of an extracted ore by using the ore itself as the grinding media. It is a process that is difficult to control and there is a lack of knowledge of the events occurring inside the mill. To find out more about how the mill behaves under different processing conditions, a full factorial test was performed with iron ore in a pilot-scale pebble mill at the LKAB R&D facility in Malmberget. To complement this work, a strain gauge detector was embedded in one of the mill?s rubber lifters, the Metso Minerals continuous charge measurement (CCM) system, and was used to get more information about the charge dynamics. The data from the experiments has been analyzed. For production purposes, an increase in the number of particles smaller than 45 µm can be regarded as a probable increase in the production rate. The analysis shows that there will be an increase in fines at 65% of critical speed, especially when the mill is 45% full. This setting will also increase the power consumption, but improves the grindability of the ore even more. The deflection of the lifters is smaller for lower critical speeds. A higher degree of filling also gives a smaller toe angle and a higher shoulder angle as expected.

Jan 1, 2011

By J. Alatalo

Autogenous grinding is a process of reducing the particle size distribution of an extracted ore by using the ore itself as the grinding media. It is a process that is difficult to control and there is a lack of knowledge of the events occurring inside the mill. To find out more about how the mill behaves under different processing conditions, a full factorial test was performed with iron ore in a pilot-scale pebble mill at the LKAB R&D facility in Malmberget. To complement this work, a strain gauge detector was embedded in one of the mill?s rubber lifters, the Metso Minerals continuous charge measurement (CCM) system, and was used to get more information about the charge dynamics. The data from the experiments has been analyzed. For production purposes, an increase in the number of particles smaller than 45 µm can be regarded as a probable increase in the production rate. The analysis shows that there will be an increase in fines at 65% of critical speed, especially when the mill is 45% full. This setting will also increase the power consumption, but improves the grindability of the ore even more. The deflection of the lifters is smaller for lower critical speeds. A higher degree of filling also gives a smaller toe angle and a higher shoulder angle as expected.

Nov 1, 2011