Search Documents

By Earl Cook

A high-energy economy based on fossil fuels is in fundamental conflict with an ideal of clean air, clean water, undisturbed scenery, and maintenance of fragile ecosystems. There is an inevitable trade-off between the material standard of living of a modern society and the conservation of its environment. During the past four years, some of the costs of environmental protection have been internalized in the energy-flow system of the United States. The cost of bituminous coal and fuel oil usable under new air-quality standards has doubled or more. The cost of mining coal underground has risen because of a 20-30 percent reduction in productivity resulting from new environmental health and safety legislation; the economic impact of proposed surface-mine regulation may be equally severe. The cost of producing electric power has been rising at a 12 percent annual rate because of environmental costs, and would be climbing still more steeply were it not for the continued forced subsidy of natural-gas consumers by natural-gas producers. The efficiency of the automobile, already a monument to the triumph of self- indulgence over economy, is being further decreased by addition of anti-pollution devices. Part of the recent sharp rise in agricultural costs stems from the fact that five energy units of fossil fuel go into U.S. agriculture for every energy unit of raw food that leaves the farm; further large injections of fossil-fuel energy occur in the transport, processing, and refrigeration of farm products.

Jan 1, 1974

By G. J. Joy

Although rates of pneumoconiosis in coal miners have declined substantially in the United States since the passage of the Federal Coal Mine Health and Safety Act of 1969, new cases continue to occur, including cases of rapidly progressive disease. In contrast, Australia's underground coal mining industry has reported few new cases of pneumoconiosis for more than 20 years. Mortality from coal workers' pneumoconiosis in official health statistics and the prevalence of pneumoconiosis among miners screened in X-ray surveillance programs are also lower in Australia. The U.S. National Institute for Occupational Safety and Health (NIOSH) was requested by both industry and labor stakeholders to examine this issue, with the ultimate aim of reducing the rate of pneumoconiosis among U.S. coal miners. A number of factors, including coal dust exposure, silica exposure and coal rank were examined as potential contributors to the above noted differences. Comparison of coal rank data from each country did not illuminate the issue. Air sample data from the coal mining industries in both countries show that coal dust levels in Australian mines are somewhat higher than those reported in similar U.S. mines; however, quartz exposure for Australian miners is lower than for many U.S. miners. If quartz is contributing to the greater number of cases of pneumoconiosis in the United States, more effective dust control measures, as well as an independent exposure standard for respirable quartz in coal mining, should be implemented to reduce this potentially disabling condition.

Jan 1, 2012

By Ronald W. Marrs

Kimberlite contains a unique assemblage of minerals and exhibits a characteristic pattern of spectral reflectance in the visible and near-infrared wavelength region. This spectral pattern is readily discerned in well-exposed kimberlite outcrops, but becomes increasingly difficult to identify when outcrops are partially covered by vegetation or soils derived from non-kiaberlitic materials. Detection of poorly exposed kimberlite diatremes is possible using multispectral imaging techniques in which spectral bands are chosen to optimize contrast between he kimberlitic soils, non-kimberlitic soils and vegetation. Careful processing of the multi-spectral data is also essential in order to separate the spectral signature of kimberlite from the signatures of other components of the scene.

Jan 1, 1984

By Kirk L. Prather

Why discuss techniques of accident prod lot on? Would it not be more useful to discuss means to reduce accidents? This discussion will answer these questions by suggesting ways in which effective accident prediction techniques improve the ability to foresee and prevent accidents. Accident Prediction Process The secret to accident prediction is to utilize the tendency for history to repeat itself. The same circumstances and the same human behavior that produced accidents in the past tend to produce accidents in the present and the future. The ability to predict accident occurence in the future by projecting from the past is a statistical process. In a bookmaker's jargon this means "playing the odds" or "the percentages". A horse or a sports team may be beaten on any given day, but by skillfully assessing the factors of past performance and assigning odds, many clever bettors make money in the long run.

Jan 1, 1973

By L. K. Eigenbrod

Throughout the mining industry, pneumoconiosis is one of the most severe occupational health problems being faced. The goal of completely eliminating pneumoconiosis as an occupational health hazard was underscored by the Federal Government with its enactment of Public Law 91-173 (Federal Coal Mine Health and Safety Act of 1969). Under this law, permissible dust level standards will be placed at 2 mg/m3 in mine atmospheres by December 30, 1972. The mining industry is thus faced with the tremendous technical challenge of achieving this level. Two basic questions can be raised with regard to this legislation. First, does a maximum dust concentration of 2 mg/m3 prevent the occurrence of pneumoconiosis? Secondly, can this dust standard be achieved using presently available methods and equipment? A precise answer to the first question has not yet been developed by the medical profession. Studies are continuing on the origin, prevention, and therapy of pneumoconiosis, and permissible dust levels could become even lower as medical evidence accumulates. The mining industry has addressed itself to the problems of dust con-tro1 for many years as related to personnel health, explosive mixtures, visibility, and machinery damage. Dust control methods being employed involve

Jan 1, 1971

By Clifford W. Schultz

Four native copper ores, two conglomerate and two amygdaloidal, were tested to determine their amenability to sorting. One of them, a conglomerate ore from the Kingston mine, showed a high sortability as evidenced by an 80 pct recovery of copper in the minus 6-, plus 1/2-inch size range. Using the Kingston as a case example, the cost of mining and concentrating was estimated for a standard case and five optional cases involving varying degrees of sorting. This analysis indi¬cates that the production cost per pound of copper can be reduced on the order of 1 to 1-1/2 cents per pound along with a significant decrease in capital investment.

Jan 1, 1975

By Praterm J. D.

The process parameters for effective utilization of nitric acid as an oxidant for copper-iron sulfides have been developed. Leaching variables found to be important were acid concentration, temperature, time, atmosphere, pressure, mineral type, particle size, and percent solids. Particular attention was devoted to analysis and control of fumes evolved during the oxidation. Responses recorded were metal extraction, elemental sulfur formation and oxidation, product gas composition and evolution rate, reagent consumption, and residue flotation response. The paper concludes by laboratory testing a flow sheet based on the above observations. Ninety-eight percent of the copper contained in a chalcopyrite-bornite concentrate was recovered, requiring 1. 6 pounds of nitric acid to be regenerated externally per pound of copper extracted. Iron remained in the leach residue as hydrogen jarosite and was ultimately rejected from the system by froth flotation. Sixty percent of the sulfur contained, in the heading concentrate reported in the elemental form; the remainder was oxidized to sulfate and eliminated with the hydrogen jarosite in the flotation tails or by neutralization of the solvent extraction raffinate with lime. Nitrogen was evolved primarily as NO and NO2; up to 3 percent N2O was also present. Gases containing sulfur were absent except when pyrrhotite was solubilized in the absence of soluble copper. In this case, H2S was evolved.

Jan 1, 1972

By S. A. Suhler

The detection of hazardous geological anomalies through remote sensing techniques is the subject of current research efforts sponsored by the U.S. Bureau of Mines. In this review, hazardous geological anomalies are discussed with respect to the "view" presented along with potential operational concepts for each technique. The design and development of a borehole radar is described with emphasis on the potential range and resolution capability of the system under realistic underground conditions. Results of field tests at two coal mines and at a hard rock future subway location are presented.

Jan 1, 1978

A conventional paddle-type mixer and a gravity flow mixing device were evaluated for conditioning of phosphate ore with fatty acid and fuel oil, and for acid scrubbing prior to cationic flotation. Gravity flow mixing required less residence-time, but slightly higher reagent concentrations to achieve recovery levels similar to conventional conditioning. Grade was less sensitive to reagent concentration using the gravity flow mixer. For acid scrubbing, the gravity flow mixer proved equally effective. In this paper, the effect of time, pulp density, reagent concentration, and emulsification on conditioning and acid scrubbing efficiency of the two devices will be discussed.

Jan 1, 1987

By Brian Stimpson

A recent study by the National Academy of Engineering concluded that if the U.S. Coal Industry is to double production by 1985 it must open 30 new 2,000,000 tons per year surface mines in the eastern states and 100 new 5,000,000 tons per year surface mines in the western states, in addition to major growth in underground mining. Major expansions in coal mining are also planned in other countries. Engineering geology can play an important part in coal mine development, operation and abandonment (Table I), and with the increasing scale of surface coal mining and the requirements of environmental legislation, it seems certain that engineering geology and geotechnics will play a growing role in surface coal mining.

Jan 1, 1976

By Robert E. Gray

The vat leaching operation at the Yerington Mine was started in October, 1953. The original plant facilities consisted of primary and secondary crushing, eight leaching vats, precipitation launders, sulfuric acid plant and the necessary maintenance, warehouse and administrative facilities. By 1961, 35,000,000 tons of oxide ore had been removed from the mine exposing the underlying sulfide ore body. A 5,000 ton per day concentrator was constructed and put into operation to treat the sulfide ore in November, 1961. The original crushing plants were used for both oxide and sulfide ores. By adding a third crushing shift for six days per week, the treated ore was increased from 12,000 to 17,000 tons per day. To balance the oxide and sulfide ore reserves, the concentrator was expanded to 13,500 tons per day in 1967. Again, no additional crushing facilities were added. It was anticipated that the treatment rate of oxide ore would be reduced from 12,000 to 9,000 tons per day. Instead, the addition of two crushing shifts per week, and improved operating procedures, increased the treated ore to 26,500 tons per day, 13,000 tons to the vat leaching and 13,500 tons to the concentrator.

Jan 1, 1975

By Harlan N. Barton

A commercially available portable X-ray spectrograph, lightweight and of rugged construction for vehicle or field camp use, was used for the determination of Ba, Cu, Fe, Mn, Pb, Rb, Sr, and Zn in stream sediment geo- chemical samples. Investigations showed a relative standard deviation of 1-3 percent, detection limits of approximately 100 ppm; and significant matrix effects. Coefficients of correlation greater than 0.9 were obtained between portable X-ray and emission and atomic- absorption spectroscopy analyses. A geochemical map of a known mineralized area showed good agreement with maps prepared by other methods of analysis and sample media.

Jan 1, 1980

By James H. Boettcher

In the second quarter of 1979, ASL Inc. inquired whether Crocker National Bank ("CNB") would provide $4 million in term loan financing to help ASL acquire the outstanding shares of the S&S Coal Company in West Virginia. ASL had, prior to approaching CNB, sought financing with the assistance of a financial advisor from a number of commercial banks without success. A summary of the initial terms requested by ASL is shown in Table I compared with the actual terms the transaction closed with. It is not difficult to note that the two sets of terms differ significantly. This is often the case when financing requests based on the expectations and vision of a mine developer are juxtaposed with more pragmatic requirements of a commercial bank. The "art" and fun of structuring financing plans for mining ventures (highly leveraged acquisitions or grass roots) comes in working with mine developers to arrive at a final financial structure that meets their objectives and constraints as well as those of the bank or other financial institution providing much of the financing. This article briefly describes the process we went through with ASL beginning with the terms they requested initially and ending with the ones on which the transaction was finally closed.

Jan 1, 1981

By Paul L. Bearden

The accumulation, handling, and utilization of sludges formed from wet process phosphoric acid is one of the major problems in the industry. The purpose of this paper is to explain some of the considerations and techniques that can be employed to provide some measure of control over the problem. An acid made from a Central Florida phosphate rock is used to illustrate the effects of one process design approach used to provide one type of control. Other approaches or techniques are discussed on a general basis. In every case, the discussion is purposely limited to conventional dihydrate processing in which phosphoric acid is produced from the filter at a strength of approximately 30% P205 and is subsequently concentrated to higher strengths such as 44 and 54% P205.

Jan 1, 1966

By G. S. Dobby

Particle collection is considered to occur by particle collision with the bubble followed by the particle sliding over the bubble during which attachment may occur. Collision is quantified by a collision efficiency, EC. The existing model for EC is extended by including particle inertia. Attachment is quantified by an attachment efficiency, EA calculated as the fraction of particles which reside on the bubble for a time greater than the induction time. These calculations use recent data on the liquid velocity distribution over the upper half of rigid spheres. Collection efficiency, EK is given by EK = EC ? EA. Detachment is not considered. The mode is examined and shown to agree with much experimental data. For example the maximum observed in recovery vs particle size (d) can be explained as E increases with increasing d , while EA decreases. The decrease in selectivity at fine sizes is in accord with the model result that for dp < 5µm, EA ? 100% (i.e. EK ? EC) almost regardless of induction time. A decrease in bubble size does increase EK but does not improve selectivity. A high particle density (> 5g/cm3) is shown to cause a sharp peak in recovery vs size and a decreased maximum size of floatability. Finally, the possible effects of bubble and particle concentration are explored.

Jan 1, 1985

By Richard L. Ash

Usually stresses generated by explosive charges during blasting are considered to propagate through materials in a spherical manner. Although conical stress-waves had been suggested by a few investigators they have never been clearly defined or critically observed. An experimental technique using models and lengths of Mild Detonating Fuse was developed to produce conical stress-waves and study their effects. Several materials with different properties were tested to compare the influence of those properties on wave shape and crater formation. The investigations showed that whenever column charges were end-initiated, conical stress-forms were produced if the explosive&apos;s velocity exceeded the energy propagation velocity of the surrounding material. The stress-cone angle significantly affected fragment size and shape as well as the geometry of craters produced.

Jan 1, 1967

By Craig J. Nelsen, J. Leroy Schutz

The Carache Canyon Prospect consists of a hypabyssal breccia pipe which intrudes a gently dipping sequence of Cretaceous Mancos Formation and Mesa Verde Group shales and sandstones. This sedimentary sequence is intruded by a number of Oligocene (34-30 Ma) calc- alkaline sills. The formation of the breccia pipe and its subsequent gold mineralization is related to the emplacement of an alkaline intrusive complex dated between 30-26 Ma. An exceptionally large block within the pipe provides compelling evidence that brecciated sills and sedimentary rocks form a relict stratigraphy that collapsed 400-800 ft (120-240 m) below their counterparts outside the pipe without substantial changes in stratigraphic position. Native gold and sulfide mineralization within and around the pipe occurs in fractures that are primarily controlled by competency differences between sills and sedimentary rocks and secondarily controlled by ductility contrasts between the relatively brittle Mancos Formation hornfels and the more ductile Menefee Group shales. The resulting pattern of gold mineralization is a series of stacked, tabular, mineralized sills and sandstone separated by barren shale in an annular region along the southwest margin of the pipe. A series of near-vertical, subparallel, sill and sandstone breccias separated by barren or weakly mineralized shale breccia occur within shallow levels of the pipe.

Jan 1, 1990

By T. Kawashima

The expanding volume of maritime coal transportation is intensifying the problems concerning large vessel service port construction, transshipment and environmental control. The major problem is the transshipment of coal. Customary methods for bulk transfer must be improved and/or new systems developed. Slurry unloading has a key role in the new systems. The present report reviews progress in slurry transportation research which has been done in Japan since the 1960s when large scale experiments for domestic transportation were done. Experiments on the effects of vibration on the slurry cargo and on reslurrying are discussed.

Jan 1, 1982

By Sheldon P. Wimpfen

Forecasting, an ancient art, is con-ducted by everyone in varying degrees. It is a vital aspect of mineral production and conditions must be predicted over a long time frame in all aspects of the industry from exploration to plant construction. Although many government agencies as well as private industry make forecasts, there are insufficent "make good" analyses performed. The performance of more such studies could sharpen forecasting ability.

Jan 1, 1983

By M. L. Bricker

The Jim Bridger Mine is operated by Bridger Coal Company and is located in Sweetwater County, 35 miles (56 km) northeast of Rock Springs, Wyoming (USA). The general location of the mine site is shown on Figure 1. Bridger Coal is a joint venture of NERCO Coal Corp, the operator, and Idaho Energy Resources Company. The permit boundary encompasses in excess of 20,000 acres (81 km2) and is nestled against the western side of the Continental Divide. Production started on July 3, 1974, and the mine has produced approximately 90 million tons (82 million t) while moving approximately 450 million cubic yards (344 million m3) of virgin earth. Annual production averages 5 to 7 million tons (4.5 to 6.4 million t) of run-of-mine coal. Coal is consumed on site by the Jim Bridger Power Plant, a 2,000-megawatt generating station, and the electricity is transmitted to the Pacific Northwest power grid (Oregon, Idaho, Northern California, etc.).

Jan 1, 1991