Search Documents

By Norman F. Schulz

The technical excellence of separation achieved in a mineral concentration process, or any other process where two constituents of any kind are physically separated from each other, is expressed uniquely and quantitatively by the Separation Efficiency: ES = (R ? Rg) where R is the percentage of the valuable constituent and Rg the percentage of the waste appearing in the concentrate. The Separation Efficiency meets all the usual requirements of a true efficiency and is independent of the nature of the process used. It can be visualized as the percentage of the feed material that, in effect, actually undergoes complete separation while the rest of the feed is distributed randomly and unchanged into the two separation products.

Jan 1, 1969

By T. A. Ring

The bed filtration of colloidal particles has been modeled by performing a differential particle balance. The balance considered the localized particle deposition rate to be the sum of three rate resistances: 1) mass transfer to a region near the surface; 2) adhesion onto a partially filled surface; and 3) resuspension from a partially filled surface. The differential particle balance equations, one for the free particles and one for the adhered particles, were solved by a finite difference algorithm. The results of this model are compared to experimental filter breakthrough curves.

Jan 1, 1983

By R. J. Lee

Asbestos analysis is conceptually simple. The objective, in most environmental analyses, is to determine the number of asbestos fibers per unit area or volume in a sample. The sample may be a consumer product, an ambient air sample, or a water sample. This determination is complicated by several factors including sample collection and preparation, counting techniques, and the operational definition of asbestos in use. Three different definitions have been used in the study of environmental samples; these are summarized in Table 1. [ ]

Jan 1, 1979

By Haydn H. Murray

Although alumina constitutes about ii percent of the earth's crust, it is expensive to separate and purify for the production of aluminum with the exception off the alumina in bauxite. The United states has a variety of non-bauxite resources that could substitute for bauxite, including high alumina clays, alunite, dawsonite in oil shale, anorthosite, and nepheline syenite. Each of these resources are discussed from the standpoint of geology, geography, processing, potential recovery, and environmental problems. Potential by-products include silica from clays, potash and sulfuric acid from alunite, soda ash from dawsonite, and soda ash and potash from anorthosite and nepheline syenite.

Jan 1, 1982

By Paul T. Allsman

The guiding principle in developing this plan resulted from evaluating potential future markets for oil, the quantity of mineable oil shale and the optimum rate of production comensurate with market demand on the available oil from shale. In addition, the rate of production may depend upon a solution to the problems of scarcity of resources other than oil shale. The rate of production finally will tend to establish the choice of technologies with these limits. The principle components discussed will be: 1) The place of oil shale among the various energy sources and its relative adaptability for use in the area of major consumptive demand. 2) A recalculation of the reserves and their classification on the basis of quantity, grade - gallons per ton, - and physical characteristics principally thickness, overburden and depth.

Jan 1, 1982

By John T. Cumberlidge

The Groveland deposit, in the Upper Peninsula of Michigan, consists of an E -W trending overturned syncline of Middle Precambrian Vulcan iron formation. At Groveland, the Vulcan formation can be divided into four units or facies. The total succession may be more than 550 feet thick, and consists of a basal unit composed of a lean chemical quartzite with traces of magnetite; a non-banded, partly clastic unit characterized by the preponderance of hematite over magnetite; a transition unit of well-banded magnetite-bearing iron formation interbedded with non-banded oolitic hematite; and a well-banded magnetite-quartz silicate unit at the top of the exposed sequence. The present magnetite-hematite ratios of different units within the orebody are considered to be a primary (post-diagenetic) feature of the original sediment. Subsequent regional metamorphism has increased the grain size of the original iron oxide minerals, but did not appreciably alter the oxidation state of the original sediment.

Jan 1, 1964

By Donald E. Steif

The Tower Mill is a vertical stirred mill using steel balls or pebble grinding media. This device is designed for fine grinding at significant power savings when compared to conventional tumbling mills. This paper describes the machine, its operation, application, and performance for wet grinding.

Jan 1, 1984

By J. A. Finch

A closed grinding circuit, typified by a ball mill-cyclone combination, is often required to treat a feed comprised of a variety of minerals of differing properties. Usually, the individual behaviour of the minerals is not assessed, a procedure which requires sizing and metal or mineralogical assaying of each size fraction. Further, sizing is frequently by screening to perhaps 325 mesh meaning that detail on the important -44 um fraction is unavailable. It is well appreciated that minerals can exhibit both individual classifying and grinding behaviour. Recognizing that cyclone classification results from differential centrifugal settling and acceleration rates, then minerals of differing specific gravity will exhibit individual mineral cyclone performance curves. If the minerals have differing grindabilities, then individual mineral rates of breakage may be expected. When treating an ore containing minerals of a range in specific gravity and/or grindability, individual mineral behaviour in the closed-circuit grind could be notable and perhaps important to the overall concentrator performance. An example is a lead-zinc ore, as shown by Kelsall et al.(1,2) This paper describes the individual mineral cyclone performance curves at sizes down to ti 10 um for the four major minerals at two lead-zinc concentrators; the Sullivan concentrator at Kimberley, British Columbia, and the Pine Point Mines concentrator at Pine Point, North West Territories, both operated by Cominco Ltd. In addition, individual mineral grinding behaviour for the four major minerals at the Sullivan concentrator is presented.

Jan 1, 1977

By C. A. Rowland

Wet grinding rod mills have been used for 50 years to grind ores and to make specification sand. The application of wet grinding rod mills is well understood. Until recently, there have been very few installations of dry grinding rod mills. The basic principles learned from wet grinding rod mills that were used in the application of dry grinding rod mills are 1. It is possible to extrapolate the performance of 5' and 6' diameter wet grinding rod mills into larger diameter rod mills with the larger mills performing as predicted. Wet grinding rod mills as large as 14' diameter (inside shell) by 20' long using 19.5' long rods are in use operating satisfactorily. 2. Wet grinding rod mills generally grind more efficiently when the fines are left in the mill feed than when the fines are removed from the feed. 3. Wet grinding rod mills produce little tramp oversize and generally can be operated in open circuit except when very close control on the top size in the product is required. When operated in closed circuit, the circulating load is normally less than 100%. 4. The power required for the desired grind can be accurately determined from the work indices obtained from rod mill grindability tests on the material to be ground. Where required it is necessary to, apply inefficiency factors for oversize feed and for larger or smaller than normal- ratios of reduction. Recent applications for rod mills have developed where it is required that dry grinding be used. These recent applications cover the grinding of 1. Lead sinter, lead slag and limestone. 2. Iron ore. 3. Silica for making glass sand. 4. Cement clinker. 5. Coke.

Jan 1, 1968

By Jozef S. Stachulak

INTRODUCTION Conveyor belt fires represent a serious hazard in underground mines. This fact is well understood in most mining countries. The statistical data for Ontario mines (1) indicates that the majority of the conveyor fires occurred at the head pulley of the conveyor belt. The main emphasis for fire prevention and detection should then be concentrated at the drive pulley of the conveyor designed to transport non-combustible material. In the case of conveyor belt fires, it is of utmost importance to detect the hazard at an early stage, when the overheating has not yet reached the ignition point. Thermal noise detection sensors were installed in 1987 at several conveyor sites at Inco mines. PRODUCTS OF COMBUSTION THERMAL DEGRADATION OF CONVEYOR BELT Various investigations on conveyor belt fire hazards have been made in the past (2, 3, 4, 5, 6, 7). Several belt samples (6, 7) were subjected to thermal oxidative degradation. The belts used in these tests were neoprene, polyvinyl chloride and styrene-butadiene rubber (6). About 70 different compounds were identified in the volatile thermooxidative products. As expected, hydrogen chloride was the major toxic product formed, accompanied by relatively low quantities of other toxic compounds such as carbon dioxide, carbon monoxide, sulfur dioxide, carbon disulfide, hydrogen sulfide, benzene, chloroprene, cresols, chloroethanol, formic acid and C8 hydrocarbons. The research investigation (8) performed by the USBM indicated that "smoldering combustibles generate a very low level of CO compared to the level of smoke produced". The cited publication (8), states that, "During smoldering combustion, typical mine combustibles produce about 2.5 times more smoke than CO. As fires develop to their flaming stages, the trend reverses and about eight times as much CO is produced as smoke." The reader is referred to several significant sources of additional information pertaining to emission products that can be found in references (8), (9), and (10). ANALYSIS OF FIRE HAZARDS U.S.A. AND ENGLAND Nearly 15 percent of all underground coal mine fires in the United States involved ignition of conveyor belts (7). In many cases, the fires propagated through thousands of feet of belt entry and created losses in the millions of dollars. Some of these fires consisted of rubber belts. Some involved polyvinyl chloride and neoprene belts that were classified "fire resistant". Typically, a belt fire begins after the conveyor is stopped. The fire is initiated by burning coal dust and grease accumulation around defective rollers or belt drives that have become heated by friction (7). An analysis of 113 conveyor fires (11) showed that 41 originated at the driving pulleys, 32 at the defective rollers, and 40 elsewhere on the conveyor system. The severity of the fire, which can spread along a conveyor road, has been emphasized by the disaster at Creswell Colliery, Derbyshire, on September 26, 1950, when 80 men were overcome and killed by toxic fumes from the fire (12). The fire started from smoldering caused by friction, and developed into a flaming combustion, propagating along the roadway containing the rubber belt at an estimated speed of 40.2 m/s (90 mph), and travelling a total of 650 m (2100 ft) THE INFLAMMATION OF CONVEYOR BELTS THE MECHANISM OF IGNITION Defective operation of a conveyor belt may start a fire in several ways: - Friction of the belt on the drive pulley. - Jamming of a guide roller, and others.

Jan 1, 1991

By Stanley N. Watowich

Recently the petroleum market has made us aware that we are indeed global natural resource consumers, and as such, we have become captive to fundamental global resource economics and their attendant vagaries. Global resource supply problems are as old as civilization and mineral exploration one of its important catalysts. On the basis of natural resources empires have been expanded and new frontiers have been developed. Global consumption and production might even be viewed idealistically as a system dedicated to optimizing distribution to the consumer. However, this is not the case. Political instability and increased government polarization make dependency on a global market somewhat insecure. The U.S. must evaluate its domestic mineral re- sources on the basis that all metals are critical and that dependency on even the common and base metals may ultimately weaken our domestic economy and our potential international relationships and could cause critical weaknesses as demonstrated by the petroleum problem. This paper evaluates specifically the Duluth Gabbro Complex, of Northeastern Minnesota, (figure l), as a potential resource of critical and strategic metals. First, a chronology of some of the early exploration, will be followed by more recent intensive company studies and preliminary evaluations of economic feasibility. Lastly, metallurgical data, on some optimum conceptual mining plans will allow metal production data to be compared with an estimate of U.S. domestic needs in 1990. The purpose of this paper is to put into focus the difficulty of converting resources into vitally needed reserves.

Jan 1, 1981

By Edwin K. Maughan

The Rocky Mountain region contains part of the paleocontinental shelf that lay in Arizona and New Mexico through Utah, Colorado, and Wyoming into Montana and North Dakota. The shelf was bounded by the northeast-southwest-trending Transcontinental arch and the Cordilleran miogeocline in late Paleozoic and early Mesozoic time. Major tectonic features that affected middle Phanerozoic sediments on the shelf were the Big Snowy trough and Williston basin in the north and the ancestral Rocky Mountains in the central part of the region. The Zuni uplift and similar positive areas occurred along the axis of the Transcontinental arch in the southern part. The late Paleozoic and early Mesozoic sedimentary rocks record transgressive-regressive marine cycles in which the Cordilleran shelf and much of the adjacent craton were inundated by epeiric seas. Early in the Carboniferous, an epeiric sea covered most of the shelf. Greater topographic relief developed in Late Mississippian, was at a maximum in Middle Pennsylvanian, and then diminished through Permian and Triassic time. The development in the Pennsylvanian Period of horsts and grabens along northwest- trending faults on the northwest flank of the Transcontinental arch resulted in the ancestral Rocky Mountain system. The eastern part of the region was emergent by Middle Triassic, and the emergence lasted until Middle Jurassic, owing to uplift along the Transcontinental arch. During the early part of the Mesozoic, the sediments were dominantly terrigenous and were deposited mostly in shallow littoral marine environments shifting to continental. Most middle Phanerozoic structural elements within the area of the shelf are characterized by lineaments that have either an east-northeast or a conjugate north-northwest trend. The east-northeast lineaments closely parallel the northeast trend of the continental slope (miogeocline) in Nevada to southern Idaho. The conjugate set closely parallels the northwesterly continuation of the miogeocline north of an approximately right- angle bend in south-central Idaho. The northeasterly trending Transcontinental arch and the northwest-trending margin of the Canadian Shield are parallel structural elements with the north- east and northwest trends of the miogeocline. The rectangular lineament pattern on the shelf suggests a system of rectilinear fractures within the underlying Precambrian crystalline basement rocks that moved several times in the Phanerozoic in response to external forces applied against the continental crust. Movement of these blocks influenced erosion, deposition, and lithofacies of the sediments in middle Phanerozoic time. Zones of crustal weakness, represented by the lineaments bounding these blocks, probably were influential in localizing sedimentary mineral accumulations and petroleum deposits, as well as later igneous intrusions, volcanism, and emplacement of hydrothermal ores. Igneous activity in this region was rare during the middle Phanerozoic, but these conjugate fractures seem to have been avenues for later passage of hydrothermal solutions responsible for ore emplacement.

Jan 1, 2013

By Wang Xuewen, Bao Qingbao, Xie Jiacheng, Yan Zewen

This study puts forward a virtual memory cutting method based on the prediction of AFC shape. The integrated key technologies include the generation of virtual teaching cutting curve, the height adjustment strategy of front and rear drum, cutting height adjustment strategy, the reciprocating cycle of cutting technology and so on. Through the two algorithms, SVM and ELM, the form of the next working cycle can be obtained by rolling prediction using the form information of AFC in the first several circulations. Based on the obtained dynamic fluctuation of the form in the vertical and horizontal working faces, the position and cutting information of the shearer during its operation can be controlled and predicted in advance, the memory cutting template can be adjusted and modified in time. Employing this method, the more stable, accurate and timely memory cutting of the shearer under the uneven coal seam could be realized.

Aug 16, 2021

By Mathew Cook

Technological developments in Distributed Fiber Optic Sensing and improvements in both hardware and software have allowed fiber optic sensing systems to be deployed in a variety of applications such as pipeline leak detection, perimeter security monitoring, and power cable real time thermal rating. Recently, there has been a larger adoption of monitoring of conveyor belts in so called Conveyor Health Monitiring Systems (CHMS) within the mining and bulk material handling industries to identify idler conditions on an ongoing basis. Several attempts have been made to institute sensing capabilities into conveyors with mixed success. However, recent breakthroughs in modeling, installation methodology, and technology, as well as increased understanding of application and industry requirements, have allowed the technology to be deployed at both experimental and commercial scales. This paper summarizes the application conditions and requirements, design considerations, methodologies used, the outcomes achieved, the logistical and field considerations, and the future possibilities of the use of this technology in CHMS using Distributed Fiber Optic Sensing.

Feb 22, 2026

By E. R. Bauer

A primary goal of Ground Control Research, Bureau of Mines, U.S. Department of the Interior, is to develop information that can be used by the mining industry to reduce accidents and fatalities due to failure of mine roof. A specific research objective is to determine methods to detect hazardous coal mine roof. This paper reviews the existing and experimental techniques, and describes a recent Bureau of Mines contract research project that resulted in a simple technique and prototype instrument for evaluating mine roof competence.

Jan 1, 1986

By K. Osseo-Asare

LIX63 in combination with DNNS selectively extracts nickel and/or cobalt from acidic leach liquors with pH values as low as 1.0. Nickel/cobalt and cobalt/nickel selectivities are achieved by varying the relative concentrations of LIX63 and DNNS. Increasing LIX63 concentration retards both extraction and strip-ping rates while DNNS has the opposite effect. Slope analyses of equilibrium data indicate that both LIX63 and DNNS are present in the extracted complexes. Examples of possible flowsheets are presented.

Jan 1, 1978

By Walter von der Linden

On April 14, 1975, Consolidation Coal Company began to operate a longwall face in their Shoemaker Mine using shield supports. This was the first time that shield supports were used in the United States (1) 1/. Shortly thereafter, Kaiser Steel Corporation started a shield longwall face at their York Canyon Mine (2). From October 1975 through May 1976, three more longwall faces were commissioned in mines located in south-western Pennsylvania and northern West Virginia. In June 1976, four installations had completed their first panel and two installations had completed the subsequent move to the second panel where coal production is now well under way. During this time (April 75 to June 76) the total number of shield support face operating months, including moving time, was 40 and the combined face advance was approx. 17, 000 feet (5200 m) with face lengths varying from 450 - 550 feet (137 - 168 m). While the shield support experience in the U.S. is still limited on the basis of time and mining parameters, the operating results of all faces have been very satisfactory. New record 24 hr production figures were set and - far more important - long term production figures could be sustained on an impressively high level even when taking face moving time into account. The purpose of this paper is to review the performance of shield type supports in the U.S. and to assess their value as longwall supports for U.S. underground mining conditions with regard to roof control, maintenance, operator convenience, safety and productivity.

Jan 1, 1976

By F. G. Miller

Over the past 30 years, the coal industry has been continually striving to perfect methods for cleaning fine coal to acceptable ash and sulfur contents while maintaining maximum product yield. The flotation process has been part of this effort and its importance is expected to grow as new utilization technology demands finer and purer coal products. The work outlined in this paper is part of a larger effort aimed at development of new and improved flotation systems for removing sulfur and ash from as-mined coal as well as for producing super-clean coal for future markets. The concepts and data presented are now serving as a basis for designing fine-coal circuits in which improved efficiency is obtained by optimum use of flotation.

Jan 1, 1986

By A. Johnson

When are SMART transmitters the smartest choice? To answer this question requires a closer look at SMART transmitter technology. It is necessary to understand this technology in order to recognize how it can best be utilized to give the greatest value for the application. And, once the decision to buy transmitters has been made, it becomes a question of whose SMART transmitter to buy. For, although the under-lying technology is similar, the differences that exist in how the technology has been implemented can make a dramatic difference in the end result. What prudent users of SMART technology do is to analyze their needs by application before making their buying decision.

Jan 1, 1988

By Allan M. Hale

Taconite tailings reclamation, especially the stabilization of tailings ponds, .dams, and slopes, can be effectively accomplished through the use of appropriate vegetation. Utilizing vegetation provides both aesthetic and ecological enhancement of a site while at the same time protecting tailings structures against wind and water erosion. Generally, the methods and techniques for establishing vegetation are well known; however, there are many site-specific factors that can alter a particular reclamation approach. Those factors include slope gradient, tailings material size, solar exposure, and physical and chemical properties of tailings. In addition to the site-specific factors, variations in climate, geography, and physiography of a region can have a pervasive influence on the success or failure of a revegetation program. Both the site-specific and regional factors control reclamation planning in such areas as plant variety selection, methods and times of plants establishment, maintenance techniques, and subsequent monitoring methods. As a result of this multifactor relationship, it is important to establish a data base that identifies both the site-specific and location conditions in order to tailor the reclamation plan to the specific area. When an appropriate data base has been collected, detailing the various site-specific and regional factors that will influence a revegetation program (in the absence of previous testing), it is very beneficial to apply experimental techniques to develop the reclamation plan for a specific site. The reclamation plan for a specific site may include several techniques adapted for the differences found within the specific site as the result of topographic or other influences. Considering this, the Reserve Mining Company and Dames & Moore undertook to develop a successful reclamation plan based on a detailed test plot program conducted at the Mile Post 7 location.

Jan 1, 1980