Search Documents

By A. J. Friedrich

Conveyor belts are designed to go unnoticed. When they work well, they attract little attention. When they are not doing the job right, it is noticeable, and they need to be fixed immediately. Vulcanising contractors compete for the maintenance of belts in mining/quarrying and general materials handling worldwide. Damage repair is approached in similar fashion. The damaged section of belting is normally cut out and discarded, and the belt re-spliced using hot vulcanising, Cold splicing, or mechanical fasteners/clip joints. However, there is a cost-effective alternative, alleviating the need to remove damaged sections which are often perfectly recoverable. This is the use of cold-curing repair resins and adhesives.

Jan 1, 2000

By H. Sevim

The logic and capabilities of a long-term production planning method for open pit mining are presented. This is a new method that can be used to obtain simultaneous solutions to the four interrelated parameters of open pit mining: mine life, specific blocks to be mined each year, the amount of ore and waste to be mined each year, and the ultimate pit limits. An efficient milling cutoff grade can also be obtained through a systematic analysis. A production plan for a real-life gold deposit is given to illustrate the logic and the capabilities of the method.

Jan 1, 1994

By Simona Markic

With the aim of environment protection the program package HOMOGEN is used for realizing the planning and noxious components control in the coal produced. Using the program package PRIPREMA the division in levels and transformation (Hermite polynoms) in the N (0,1) distribution are made. By separated kriging 50 m x 50 m blocks are estimated on the levels and detailed distributions of the estimated component content are obtained. The face - longwall face is built in the blocks estimated in this way, and the direction of mining is determined. Using the stochastic simulation the distribution of the estimated production component (e.g. sulfur) on the face is obtained. Simulating the production of all faces in operation the distribution of the estimated daily mine production component is obtained. The estimated depot component is obtained in the same way. This procedure is used in the short-term planning of the estimated component movement for a given period in advance, and also in the daily production control in the case of changing conditions, e.g. the increased atmospheric pressure. The technology is successfully applied to the Velenje Lignite Mine Slovenia.

Jan 1, 1992

Building aggregates, basic materials for the construction industry, must be produced according to socio-economic and environmental sustainability principles, i.e. the three fundamental components of Sustainable Development. On this subject, an introductory discussion about the interpretation of these concepts in the field of mineral production and construction industry is first presented. As for the socio-economic aspect, aggregates are then illustrated as being essential resources for the development of the society, underlying that it is possible to understand their fundamental socio-economic role only through the analysis of the whole product life cycle, from production to end use and beyond. The same has to be done on the environmental side to assess the environmental impacts of aggregates: one should look for, not in the quarry phase only, but also in all the downstream activities of the construction process, including the use phase and beyond. Based on this approach, in the second part of the paper, the results of some investigations focused on eco-profiles of building aggregates, gathered through the application of LCA methodology are presented and discussed. In such a context, strengths and weaknesses of LCA indicators will be discussed, as well.

Jan 1, 2007

By J. Hanna, J. Jung, I. J. Anazia

Electrothermal production of elemental phosphorous (P4) generates substantial amounts of highly toxic phossy water and sludges. Because of their high phosphorous contents and lack of reliable processing technology, large tonnages of these hazardous wastes have accumulated from current and past operations. To date, the sludges are stored in ponds or above ground in special containment vessels at various locations around the country. Two samples of electric furnace phosphorous sludge (obtained from the Tennessee Valley Authority (TVA) in Muscle Shoals, AL and FMC Corporation in Pocatello, ID) were investigated using physical separation techniques to recover the elemental phosphorous and to render the residual material nonhazardous. The techniques tested include sizing, froth flotation and dispersed air oxidation. Flotation and sizing produced concentrates containing 69% - 90%P4, with recovery in the range of 60% - 87%. Dispersed air oxidation of the fines and tailings products was effective in the removal of an additional 10% - 15% of the P4 in the sludge.

Jan 1, 1993

By F. F. Peng, D. C. Yang, G. Yanief, E. H. Cho

This study deals with carrier flotation of cerium dioxide, a surrogate of plutonium oxide, which is the major contaminant at the Nevada Test Site (NTS). The objective of this study was to determine the feasibility of using carrier flotation for remediation of the site. In this study, a - 200-mesh fraction of pure cerium dioxide was used. Oleic acid was used as the collector, while calcium carbonate was used as the carrier. Mechanical-cell tests were conducted to float the surrogate from a mixture containing uncontaminated NTS soil, both in the absence and presence of the carrier. It was found that the addition of the carrier drastically enhanced the flotation recovery of cerium dioxide. The flotation recovery of the surrogate increased from 34% to 65% by adding only 0.5% calcium carbonate (-150 mesh). The recovery further increased to 95% by adding 10% calcium carbonate. The flotation method utilizing a carrier of calcium carbonate seems to have a high potential for the remediation of the soil contaminated with radionuclides at the NTS.

Jan 1, 1998

By I. Shah, L. G. Austin

A method for quantitative investigation of the phenomena involved in fine grinding of materials that follows the changes in the breakage rates of fine particles has been presented. For relatively hard, brittle, non-coating material like quartz, the slowing down effect of breakage rates starts to be significant at relatively coarse sizes, which goes often undetected in closed circuit grinding systems, producing relatively coarse product, say P80=75µm However, for fine grinding systems, as the -10µm fractions begin to build-up, and classification becomes more difficult, the build-up of fine sizes causes a slowing down effect Compounding this problem is the difficulty of obtaining accurate cumulative weight size distributions in the fine size region.

Jan 1, 1983

By D. Krzyszton, P. Czaja

Mining explosions in rocks originate stress waves of great intensity, which crush the surrounding rocks and are then propagated as a seismic wave. Seismic waves are the cause of dynamic loading of pillars and their subsequent destruction. In calculating safe dimensions for inter-room pillars, not only the stresses conditioned by overburden pressures should be taken into consideration, but also the dynamic stresses caused by explosion. This is of particular importance for pillars with great specific acoustic impedance which have been destroyed mainly by the reflected seismic wave. It is possible to take dynamic loading into consideration in the calculation of pillars when the parameters of the propagation wave, the dynamic elastic constants of rocks, the strength properties of rocks, the strength properties of rocks subjected to dynamic loads and the parameters of the blasting charge are known. An example of the calculation for the safe width of an inter-room pillar subjected to the seismic effect of an explosion is given and the possibilities of reducing the dynamic loading of pillars are discussed.

Jan 1, 1982

By Meliton M. Garcia, Satya Harpalani

This paper discusses the results of an investigation carried out in an underground mine to characterize the volatile by-products adsorbed on airborne particulates following the detonation of four common explosives including ANFO. The primary objective of this study was to determine if any organic amine compounds, particularly nitrosamines, and any polycyclic aromatic hydrocarbons were produced and trapped in the dust that a miner might inhale during the workday. The production of these substances is of great concern because of their suspected carcinogenic nature. The results of the study indicated that a large variety of the by-products are adsorbed on the particulates generated, and thus remain airborne following the detonation of explosives. The major by-products retained by the dust were bis(2-ethylhexyl) phthalate, and aliphatic hydrocarbons with carbon chains ranging from C12 to C28. One explosive, a water gel, produced the polycyclic aromatic compound, trimethylnaphthalene. No nitrosamine compounds were detected.

Jan 1, 1989

By Henry P. Ehrlinger III, Latif Khan, John M. Lytle

The primary purpose of this project was to produce and test coal concentrates made from coal preparation plant waste fines for use in a slurry-fed gasifier. Concentrates from several individual waste streams were examined to determine their amenability as feedstock for a slurry-fed, slagging, entrained-flow gasifier. The tests included analyses of the plant feed and product, material balances, and estimates of gasification reactivity and of pumpability. The following preparation plant fines were examined: • fresh rejects produced in a plant processing underground- mined Springfield Coal • fresh rejects produced in a plant processing underground- mined Herrin Coal • fresh rejects produced in a plant processing surface-mined Springfield Coal and Herrin Coal • Five-year old impounded fines rejected during processing of underground mined Herrin Coal. At high coal recoveries the Btu content of the concentrates was greater than the Btu content of the utility product from the plant. The coal recovered from fines was found to be entirely acceptable for gasification and pumping without additives.

Jan 1, 1995

By Tomb. T. F., R. A. Haney

During the past several years, the Mine Safety and Health Administration (MSHA) has conducted studies in underground mining operations to obtain information on occupational exposures to diesel particulate (DP), mine environmental DP levels and on the effectiveness of methodologies used to control DP. The studies conducted were representative of four coal mines and 10 metal mines. The metal mines included two lead-zinc mines, one limestone mine, two potash mines, one zinc mine and four salt mines. Three of the four coal mines were using disposable diesel exhaust filters to remove particulate from the exhaust and one was using a reusable wire mesh filter. Results of these studies indicate that average DP levels in coal mines not using exhaust filters range from 0.9 to 2.1 mg/m3, The use of exhaust filtration devices reduced these levels by about 50% to 90%. Studies conducted in metal and nonmetal mines showed average DP levels ranging from 0.3 to 1.6 mg/m3.

Jan 1, 1996

By Gerald L. Dollinger

INTRODUCTION Today more tunnels are being bored by mechanical means in igneuus and metemorphic rocks (i.e. "hard" rocks) than ever before, and there is reason to believe that this trend will continue in the future. Because of this, there is an increasing demand fur stronger, more powerful machines and fur cutters that are capable of handling the high loads and abrasive rock conditions that often accompany hard rock tunneling. Tunnel boring machines ("TM's") built today, therefure, generally have higher thrust and torque capabilities than those built in the past, and they are equipped with the largest cutters and rings now available. The recent experience in hard rock tunneling has demunstrated that TBMs can be both efficient and ecunumical under such conditions, and that acceptable performance rates can be achieved in all but the hardest rock. In spite of this success, it is believed that improvements in buth the cost of boring and in performance rates can still be made through mudificatiuns in the existing kerf cutting system. Some impruvements in TBM performance under hard rock conditions, fur example, have already been made thruugh the development of constant section rings that maintain a constant edge width and, therefore, a constant level of performance as they wear. The recent experience in hard rock tunneling has also produced a wealth of new TBM performance data through the systematic study

Jan 1, 1983

By R. L. Bleifuss, S. Zhong, H. E. Geotzman

Microwave heating of iron ore was investigated as an alternative to conventional reduction processes to solve the problem of slow heat transfer. Microwave heating and reduction tests were run on composite green balls made from coal and magnetite concentrate. Benchscale tests were run on both powdered and pelletized feeds using a 15 kW microwave generator. A significant increase in the reduction rate was obtained. With 20% excess stoichiometric carbon in the mix, more than 90% reduction of the iron ore can be achieved in about 10 min at temperatures of around 1,000°C. The reduction of iron ore with coal by microwave heating produces a pure, dust free, high-Btu flue gas that can be used in related thermal operations. Depending on the purity, the reduced iron product could be fed directly to an electric arc furnace for melting. In some cases, the removal of a slag phase may be required to eliminate excess silica and alumina.

Jan 1, 1997

By P. E. Nielsen, T. L. Loga, B. B. Mauko

A numerical model is presented which simulates the dynamic fracturing process for a circular geometry fracture in a uniform stress medium. The dependence of crack aperture and net pressure in the crack upon various dominant parameters of the fracturing process is discussed. An analysis of a 75% nitrogen foam fracture in a coal seam at 5600 feet (1707 m) is also presented. The analysis is based upon the discussed parametric trends, the job records of treatment parameters, and a Nolte plot of net downhole pressure. It is interpreted that fracturing with water, in pre-foam fracture pump tests, resulted in significant fracture height growth. However, the subsequent foam fracture had reduced height growth due to the high effective viscosity of the foam and due to the higher magnitudes of elastic modulus and stress in the bounding rock strata with respect to the coal.

Jan 1, 1986

By George H. K. Schenck

Decisions to develop deposits of calcareous materials for cement production are based largely on anticipated markets for heavy construction which utilizes concrete. The geologist should understand the fundamental factors that underlie such management decisions, so that his field work and reports will more effectively relate to the information requirements of managers in the cement industry. The paper examines the relationships that exist between exploration and development of calcareous raw materials for cement manufacture and changing factors in the marketing of cement. Continued overcapacity, improved technology, changing distribution patterns, ease of entry, economics of scale, and the nature of product demand are some of the characteristics of the cement industry that are basic to decisions regarding exploration programs and property development.

Jan 1, 1966

Cost accounting information is used primarily for (1) planning, control, and performance evaluation; and (2) managerial decision-making. Incremental analysis is a tool for managerial decision-making. It is designed to estimate future financial performance, namely the benefits and costs associated with alternative courses of action. Decisions may be distinguished as pertaining to short-term or long-term activities. Long-term activities frequently focus on capacity decisions and the attendant capital budgeting processes used to quantify the financial effects of these decisions. Short-term decisions typically address short-range production quantity and pricing issues, outsourcing, selection of the optimal mix of products, inventory management, and the acceptance of special orders. This chapter addresses these short-term decisions.

Jan 1, 1999

By B. Elevli, M. D. G. Salamon

Production scheduling of an open-pit mine is one of the most important steps in open-pit mining. The mine's production schedule defines the distribution of cash flows and, as a result, directly influences the net present value (NPV) and overall economic feasibility of a project. The need to plan and operate a mine with an optimum production schedule has been obvious for some time, but the methods used to obtain such a schedule have not been so obvious. The current practice is to do a trial and error analysis by hand. In an attempt to improve the way production scheduling is currently done, a new computer based production scheduling algorithm was developed. This paper describes the fundamentals of this newly developed heuristic scheduling algorithm and its application to a gold deposit. The results of this case study show that the schedules, based on the new method, provide improved cash flows compared to production schedules done manually.

Jan 1, 1992

In the hierarchy of performing mine planning tasks, production scheduling is naturally at the bottom. Yet good production scheduling is probably the most demanding and difficult task to achieve for various reasons. Being the last task in the mine planning hierarchy, a proper production schedule must not only conform to both the long-range and the short- range mine plans but also satisfy many practical details that are unique to day-to-day operations. For example, the averages which were good enough for both long-range and short- range mine planning are no longer good enough for production scheduling. Instead, the variations become the overriding concern. The answer must also be obtained quickly and on time, thus adding another dimension to the overall problem. Because of these considerations, many production scheduling problems have been begging for solution during the past decade. Many attempts were made to solve the production scheduling problems in the past using computers and the available operations research (OR) techniques, particularly among academic groups. However, it is probably true that, compared with the current full-time computer usage in long-range and short-range mine planning, very little computer usage is being made in production scheduling to date.

Jan 1, 1979

By Byron N. Cooper

The Revenue Act of 1926 provided for five simple categories of natural resources to have the benefit of depletion allowances. In the 1947 Revenue Act, the number was increased to twenty-five, and in the 1951 Revenue Act to fifty-four. Of this number, fourteen were allowed 5 per cent; nine, 10 per cent; twenty-nine, 15 per cent; one, 23 per cent; and one (oil and gas), 27.5 per cent. The 1951 Revenue Act created a host of difficulties, including application of the "end- use criterion" and determination of the commonly accepted meaning of such terms as limestone, dolomite, chemical- and metallurgical-grade limestone, marble, calcium carbonates, and magnesium carbonates. Dolomite, for example, was listed at 10 per cent depletion allowance, but without definition. In the great amount of litigation growing out of the 1951 Revenue Act and its administration, it became essential to understand the derivation and subsequent usage of these common geologic terms. One thing that became clear was that our definitions changed significantly between the time that the 1951 Revenue Act became law and the time that later cases were tried. Some geologists neglected to learn about first usages of such terms as metallurgical limestone, and about meanings that were applicable when the 1951 Revenue Act was written and passed. Legal meanings in this paper are discussed in the light of certain famous cases that have been tried and settled.

Jan 1, 1966

By M. A. S. Martins, H. Medeiros, B. Y. B. Dos Santos

This paper contains the geometallurgical studies, performed for Mineração Rio do Norte bauxites, applied to a selected area belonging to Plateau Saracá III, referring to an exploitation period of one year and three months, approximately. It is worth mentioning that Mineração Rio do Norte has the biggest bauxite operation in Brazil producing 8,500,000 tons of concentrate per year. The studies included wide investigations directed to the final objective of establishing a precise mining and production planning, based on the different behavior of the distinct bauxite ores, when submitted to industrial processes. Geometallurgy can be defined as the study of the regionalization (space distribution) of the metallurgical variables of a mineral deposit. This study involves and integrates all process engineering, geology, geostatistics and mining planning, among others. The development and application of the geometallugical studies to Mineração Rio do Norte were motivated by several reasons and necessities, among them: 1. Improving the forecast of the amount of concentrate (metallurgical mass yield) produced; 2. Improving the equipment operational efficiency, providing a more homogeneous feed; 3. Conducting a more precise material balance that permits a better daily, monthly and yearly production control; 4. Improving the forecasts for the final products generated by each ore type; 5. Obtaining better knowledge of the behavior of several ore types, submitted to the different process unit operations; 6. Promoting adequate ore blending, producing an homogeneous feed during mining operation.

Jan 1, 1998