Search Documents

By L. G. Austin

Introduction My first contact with industrial milling was during the time I worked in the electricity generating industry in the United Kingdom. In visits to power stations to investigate either deposits in the boiler furnaces or polluting deposits settling around the stacks. I had to check the performance of the vertical coal pulverizers, since poor pulverization aggravated both problems. Naturally, then, when I came to the USA in 1957 to take a PhD in fuel technology at Penn State, I was put to work to review the science of coal pulverization. After this reviewing, I was completely confused. On one hand, there was a well-developed understanding of stress-strain equations, and a rap- idly developing knowledge of how stressed, brittle solids fractured, based on the Griffith crack theory. On the other hand, reading in the grinding literature gave me: • Kick's Law, which was clearly not correct in the light of modern fracture theory; • Rittinger's Law, which was also clearly not correct; • Bond's Third Law of Comminution, which was claimed to have something to do with the Griffith crack theory, but where the connection between the two was made by intuitive pseudo- scientific reasoning I could not accept; • the choice of mill motor power for the most common type of coal mill, the Raymond pulverizer, was calculated from the fan power required to move air through the mill. Although I could accept the empirical connection between the two, it made no sense from the point of view of fracture energy. Even today, most books or review chapters on size reduction start from these laws. incorrect statements abound in the literature, such as “the Hardgrove Index is based on Rittinger's Law," which it is not, "The Bond theory states that work input is proportional to new crack tip length produced in particle breakage," which is not true, etc. My own test work showed that these "laws" did not fit the data for grinding of coal. At about this time, Epstein (1 948) and Broadbent and Callcott (1 956), following the original work by R.L. Brown (1941) at the British Coal Utilization Research Association, proposed describing breakage as a series of fracture stages. I took their concepts and developed the basic differential equation for a batch grinding process continuous in time, analogous to a batch chemical reactor. Robin Gardner then joined the project and did his PhD on treating batch grinding in the same way as a batch chemical reactor. He found that the basic equation had already been partially derived by Sedlatschek and Bass (1 953) in Germany. We confirmed experimentally the validity of the equations for describing batch grinding (1 962) and formulated the equation describing steady-state continuous grinding in a fully-mixed mill. At about the time this work was published, Gaudin and Meloy (1962) and Filippov (1961) independently published essentially the same equations, but without experimental proof of the validity of the concepts. I will give a brief overview of what these beginnings had led to in the design of mills for size and power, and show some of the results of this more detailed understanding of grinding processes. Concepts of Fracture Mills such as tumbling ball, rod, pebble and autogenous mills and vertical mills such as the Raymond, and E-type apply compressive stress to lumps or particles relatively slowly. Compressive stress applied to a particle of an elastic brittle solid imparts overall strain energy to the solid and produces local regions of tensile stress, (Fig. 1) (Berenbaum and Brodie, 1959). Irwin (1949) showed from solution of the stress-strain solutions that a small hole in a region of tensile stress reduces stress concentration at the hole, that is, the tensile stress at the tip of a crack or flaw in a solid is much higher than the general tensile stress in the region. The longer the crack, the higher the stress concentration. Griffith (1920) hypothesized that when the regional tensile stress is large enough, then the chemical bonds at a preexisting crack tip are stretched to breaking point, as illustrated in Fig. 2. When the bonds break, the crack becomes longer, the tensile stress concentration increases, the situation is unstable and a crack opens up (propagates) a surface of tensile stress, creating its own tensile stress at the leading edge. Stored strain energy is converted to the kinetic energy of the moving stress field, which is analogous to sound propagation through the solid, so the crack tip accelerates to velocities approaching those of sound. The moving crack will pass through regions that were previously under regional compressive stress. The equations for "ideal" and "Griffith" strengths are where a is the intermolecular distance, y is Young's modulus, g is the energy

Jan 1, 1998

By John A. Herbst, William T. Pate

Column flotation is emerging as one of the most important new separation technologies of the decade. Attendant to this development is the need for a quantitative understanding of the dynamic characteristics of columns. An understanding of the many important sub-processes occurring in the cell makes possible the development of dynamic simulators for flotation columns which will aid in the design of control systems for dynamic and steady state optimization. This paper presents a dynamic model for the column flotation cell developed from a population balance point of view similar to that which has been successfully applied to conventional flotation cells. In particular, the mixing that occurs within the pulp is modeled with a distributed-volume, mixer-in-series model as an approximation to the axially dispersed plug flow transport that occurs in the cell. This simpler approach avoids the distributed transport model which often leads to mathematical intractability. Other phenomena dealt with are the attachment and detachment of particles from bubbles in the froth and pulp, the transport of water and the bubble volumes with the froth and pulp phases. Simulation of the flotation of an Illinois No. 6 coal in a pilot plant flotation column were performed to test control strategies.

Jan 1, 1989

By M. S. Basich, J. S. Scope1, J. H. Raeder

During 1983, The Youghiogheny and Ohio Coal Company's lost-time-incidence rate was 8.1, equal to the average for underground bituminous operators. How- ever, one half of all lost-time injuries were low back, back and neck related. In reviewing these results, we determined that substantial improvement could be made. We investigated existing back schools and the possibility of opening an in-house clinic. In September 1984, we began The Youghiogheny and Ohio Coal Company's Back Care Program. The objectives of the program are to reduce the number of back injuries incurred at the work site, hasten recovery time, decrease medical and workers' compensation costs and provide the employee with a thorough understanding of his problem. A state-of-the-art clinic capable of treating injuries to the spine and extremities has been established at the work site. The clinic is staffed by a licensed physical therapist and is offered to all employees on a voluntary basis under physician referral. The approach to treatment is multi-phasic. For the typical patient, the initial goal is to reduce pain and correct dysfunction. Treatment modalities such as auto-traction, extension exercises, ultra sound and moist heat are frequently used. During this period the patient is given extensive education regarding his problem. As soon as more vigorous activity can be tolerated, a work-hardening pro- gram consisting of job simulation activities designed to improve flexibility, strength and functional capability is begun.

Jan 1, 1986

By J. Abbott

This paper gives a brief description of the Compania Ninera del Pacifico (CNP) a subsidiary of the Campania Acero del Pacifico (CAP), its participation in the Chilean Iron Ore mining and the gradual development of its activities. mainly in this paper, it is explained the CNP experience in the production of 34 million tons of self-fluxing pellets for Blast Furnace in a period of ten years in its Huasco Pellets Plant.

Jan 1, 1989

Traditionally, production volume has been considered the major determinant of cost. As volume increases, total cost increases but unit cost decreases. This concept has been so widespread in industry that many of the tools used to analyze costs are based on production volume as the sole measure of activity and driver of unit cost-fixed and variable costs, cost-volume-price and breakeven analysis, contribution margin, flexible budgets, and others. Clearly, volume is a driver of cost. It is important in both a tactical sense (to the manager at an operating mine) and a strategic sense (as one determinant to the firm's overall cost position). However, many other factors influence costs as well, even though they have not been studied to the same extent. For example, production managers know that their costs will be reduced if the workforce does not have accidents. Safety costs are to a large extent independent of volume. Other cost components increase as volume increases, such as some environmental charges. Some costs may or may not reflect volume changes. Maintenance, for example, may appear as either a fixed or variable cost, as can operating labor in facilities that are highly automated. In the strategic sense, where the firm is selecting a strategy to pursue competitive advantage and increased profitability, all costs are variable. This reflects both the strategic intent and the long-term time frame associated with strategic positioning. Tactically, on a month-by-month basis, some costs are essentially fixed. Cost driver analysis must therefore consider the relevant time frame.

Jan 1, 1999

By Jakub Nalaskowski, Robert Aranowski, Jan D. Miller, Jan Hupka

The polyolefins, mainly polyethylene and polypropylene particles, are used as an active filler material in polymer-polymer blends and are being used for the modification of asphalts to pro- vide for high-load, low-maintenance road construction. The stability of prepared blends depends on the interaction forces between polyolefinfiller and the matrix and/or between two polyolefin filler surfaces in the polymeric matrix. Various additives, especially surfactants, can be used to modify these interactions and improve the stability of polymer blends. In current research, direct force measurements between polyethylene (PE) surfaces in n-tetradecane, a nonaqueous solvent imitating the polymer matrix, were performed in the presence of lauric acid and dodecylamine using the AFM colloidal probe technique. Additionally, the zeta potential of polyethylene particles in the presence of surfactants in n-tetradecane was measured. The interac- tion forces between the polyethylene surfaces can be described as a combination of electrical double layer repulsion and steric repulsion between polymer chains extending into the n-tetradecane sol- vent. The addition of surfactant to the n-tetradecane was found to increase the repulsive force between the PE surfaces. The strongest repulsion was observed for dodecylamine. Additionally, the temperature efect on the interactions in n-tetradecane was studied. It was found that steric repulsion between the PE surfaces increases with an increase in temperature.

Jan 1, 2003

By C. J. Pritchard

As productivity improvements reduced the number of continuous miner sections from seven to three while maintaining full productive capacity, a decision was made to test an advancing tailgate ventilation system on the shortwall mining section. Having the shortwall mine its own return air system has freed the third mining section for more productive, less costly mining. The advancing tailgate has provided effective ventilation across the face and gob with acceptable pressure losses. The tailgate development continuous miner section has been since transformed from a low productivity part-time function to a high productivity development/retreat panel and is available for long term mine development duties also.

Jan 1, 1989

By J. D. Miller, C. L. Lin

As the techniques and resolution for three-dimensional spatial analysis have advanced in the last decade, it is now possible to map in detail the microstructure of multiphase materials in three-dimensional digital space. In this regard, three-dimensional X-ray microtomography offers a unique imaging capability. Spatial resolution on the order of 10 µm can be achieved with the use of microfocus X-ray generators. Recently, a state-of-the-art cone beam X-ray microtomography system was installed at the University of Utah for the quantitative analysis of multiphase materials in three dimensions. This facility was designed to obtain 2,048 by 2,048-pixel reconstruction over a 10-mm diameter, while also allowing for the imaging of somewhat larger (40-mm) objects. The system is capable of handling high-density materials, even materials having a density as high as 8.0 g/cm3. This unique, one-of-a-kind instrument can be used to obtain three-dimensional spatial reconstruction for many applications, such as three-dimensional liberation analysis, pore structure analysis of particle beds during filtration and the air-void system of concrete structures. The utilization of X-ray microtomography not only allows for the quantitative analysis of multiphase systems but also allows, for the textural characterization and determination of phase continuity. This paper presents information regarding the current use of this new facility and a review of potential applications for the advanced analytical system. Key words: Cone beam X-ray microtomography, Three-dimensional analysis, Material characterization

Jan 1, 2003

By Richard S. Ghent, Daniel G. Warnock

JOHN HAMRIC: Our next speakers are Richard Ghent, manager of environmental health and safety for CF Industries, Hardee Phosphate Complex, in Wauchula, Florida. Richard has 20 years' experience with environmental health and safety affairs. He has a bachelor of science degree from the University of South Carolina. With him is Daniel Warnock, who is supervisor of safety and training also at the Hardee Phosphate Complex. Daniel's experience is in safety programs and electrical training. Their presentation is "Regulations Versus Management Practice." RICHARD GHENT: Written procedures give structure to safety programs. At their best, they are brief and understandable to facility personnel and clearly identify roles and responsibilities. At worst, they attempt to recite the entire regulation they are intended to address. Some regulations, such as OHSA's Hazard Communication Standard, require employers to develop, implement, and maintain a written program. As written programs and procedures are developed, some basic questions arise: Is the program designed to achieve compliance with regulatory requirements or does management expect the program to go beyond compliance to some higher level of performance? Management may have difficulty in measuring and communicating performance expectations in safety. A facility with 4 million safe work hours does not suddenly become unsafe the day their safety record is broken. Generally, management expects safety programs to meet regulatory requirements and to protect the employer from enforcement actions and fines from regulatory agencies. Management also expects that safety programs will result in a safer work environment with fewer incidents, accidents, and near misses. But it is difficult to know when a safety program has succeeded. If the program is expected to go beyond compliance, what other standards should be included (e.g., ANSI standards, company management practices, lessons learned from inspections and audits, recommendations from safety committees, etc.) in the

Jan 1, 1998

By G. Vik, P. Chryssanthakis, S. C. Bandis, L. Haruik, N. Barton, M. Christianson, A. Makurat

The large jointed chalk reservoir situated at 3 km depth in the North sea's Ekofisk field is undergoing major compaction after nearly 15 year of oil and gas production. Approximately 150 km 3 of the overlying sediments, mostly shales, are involved in the subsidence. A maximum central subsidence of nearly 3 meters, and a maximum present rate of 45 cm per year has set in motion numerous studies of the phenomenon. Non-linear finite element (FEM) and non- linear distict element (DEM) analyses of the compaction and large scale subsidence were performed. Consistent differences between the continuum and discontinuum analyses were noted. In the latter, slip on hypothetical bedding planes and sub- vertical or vertical faults was allowed, which possibly gives a more realistic simulation of the real processes of subsidence in such a large body of rock. Laboratory studies of the reservoir joints included roughness measurement, JRC and JCS characterization, direct shear tests while saturated in heated Ekofisk oil, and coupled closure-shear-flow tests with heated oil followed by heated sea water. Discontinuum modelling using Cundall's UDEC was performed on representative jointed assemblies (two sets of steeply dipping conjugate joints) to investigate the effect of a major reduction of pore pressure within the deformable matrix and along each joint. It was found that the large shrinkage deformation of the matrix allowed joint shearing to occur despite the constraint of uniaxial strain. Relative mass bulking due to small but widely distributed joint shear possibly explains the observed maintenance of excellent productivity despite large vertical strains in the reservoir.

Jan 1, 1986

By W. J. Schlitt

Introduction Heap and dump leaching are low-cost metal production techniques that are gaining in popularity among gold and copper producers. However, the flow of solution in heaps and dumps has received little attention in the literature. This is unfortunate since solution flow is one of the few parameters subject to operator control. Thus, solution management may well influence both operating costs and plant performance. Costs aside, there are two important aspects of solution flow to be considered -the metallurgical and the hydrological. Some of the metallurgical factors have recently been discussed (Jackson and Ream, 1980; Schlitt, 1984; Schlitt and Nicolai, 1987). These cover solution application rates and methods, irrigation rates, leach-rest cycles, and nonvertical solution flow. According to Caldwell and Moss (1985), however, the hydrological aspects may be more significant than the metallurgical ones. In particular, a phreatic surface will form when excessive flow leads to an accumulation of water and the associated buildup of pore pressure within the rock pile. Such internal flooding can either originate at the foundation or at some other zone of very low permeability. The latter condition gives rise to an impounded volume of solution, i.e., a perched water table (see Whiting, 1985). Caldwell and Moss point out that a rising zone of saturation is probably the most common cause of dump failures. Of course, such failures have even occurred in heaps that were carefully prepared for leaching (Milligan and Engelhardt, 1984). Thus, flooded conditions and perched water tables represent an important safety consideration as well as having an impact on metallurgical performance. The following sections describe a case history in which a perched water table developed within a copper leach dump. The description includes background information, solution flow rates, and metallurgical data. Then this situation is compared to one involving normal drainage. Description of the leach system The leach dump in the case history is located at a shutdown open pit copper mine. It was built in two lifts, with the second added some 20 years after the first. There is little detailed information available on the initial lift. It was built with rail¬hauled waste and was generally less than 30 m (100 ft) high at the crest. The area available for leaching was about 120 m (400 ft) wide and more than 380 m (1250 ft) long. The dump surface was prepared for leaching by dozing ponds approximately 12 m by 12 m by 2.5 to 3.0 m deep (40 ft by 40 ft by 8 to 10 ft). The ponds were leached by flooding with barren leach solution returned from a scrap iron cementation plant. Based on mill feed at the time, the average waste grade was probably close to 0.4% Cu. The first lift leached well. It accepted high flows, which together with the waste grade, produced a rich pregnant leach solution (PLS). Old records indicate a PLS of "50 lb Cu/ 1000 gal," or about 6 g/L. As later drilling would indicate, such a high tenor led to dissolution of considerable scrap iron that was returned to the dump. The iron then hydrolyzed and settled out on the pond bottoms. In addition, the waste settled substantially so that the unleached crest was 3.0 to 4.5 m (10 to 15 ft) above the ponded area. Eventually, the leachable copper was extracted and the dump became less permeable. Thus, the PLS tenor dropped until it became uneconomical. About ten years later, mining resumed and the decision was made to add another lift to the dump. This was done without giving much thought to a subsequent leach operation. Hence a 24-m (80-ft) lift was built on top of the original dump. The surface of the latter was not prepared in any way, e.g., by leveling and/or deep ripping, prior to over-dumping. Examination of subsequent drill cuttings indicated that the new lift contained about 0.2% Cu, with chalcopyrite and chalcocite (50:50) being the predominant copper minerals. Most of the chalcocite occurred as rimming on the abundant pyrite, with the pyrite to chalcopyrite ratio estimated at 10 to 1. The use of 100- and 120-ton trucks for haulage caused some waste compaction during emplacement. In addition, the host rock itself was relatively soft, being a porphyry intrusive material that was partially altered to clay. As a result of the initial compaction and clay swelling, the rate of water percolation from the new leach ponds was slow and the ponds often contained considerable standing water. Even frequent ripping failed to provide a sustained improvement in the percolation rate. The poor surface permeability was exacerbated by hydrolysis of iron salts which settled as a layer on the pond bottoms. Partly as a result of the permeability problems, metallurgical performance was not up to expectations. These had been based on laboratory tests which showed about 20% copper solubilization in two weeks. Continued copper extraction in the tests also suggested that a substantial percentage of the copper would eventually be recovered. However, the PLS grade in the actual operation peaked briefly at about 0.48 g/L Cu (4 lb Cu/1000 gal), then declined to a range of only 0.24 to 0.36 g/L Cu (2 to 3 lb Cu/1000 gal). The poor leaching was traced to a lack of oxidation of the sulfides. There were two principal observations supporting this conclusion. First, there was no evidence of any heat being generated within the dump. As discussed elsewhere (Schlitt and Jackson, 1981; Hiskey and Schlitt, 1982), pyrite oxidation is quite exothermic and the high pyrite content of the waste should have led to an increase in the temperature of the leach solution as it percolated through the rock pile. Second, there was no sign of any natural convective air flow through the dump.

Jan 1, 1987

By Daryl L. Gusey, John T. Neubert, Matthew A. Sares

The Colorado Geological Survey completed an inventory of environmental degradation associated with abandoned and inactive mines on National Forest System lands in Colorado. In the course of the inventory, areas with naturally occurring acid rock drainage were also noted. Approximately 18,000 abandoned mine- related features were inventoried, including about 900 features that are considered significant enough environmental problems to warrant further investigation. Water quality data, such as pH and conductivity were gathered at all features where water was present, such as draining adits, seepage at the toe of dumps and tailings, and standing water in shafts. Samples were taken where field tests indicated low pH andlor high conductivity, including several areas with naturally occurring acid rock drainage. Samples were analyzed for dissolved and total metals, and for selected anions. All mine locations and data collected by the field geologists were entered on field forms and, subsequently, into a computer database and GIS format. With the information provided by the inventory, the Forest Service, in cooperation with other agencies, has been able to prioritize abandoned mines for reclamation. In most cases, cleanup is approached on a watershed basis. Mines in priority watersheds have been selected for reclamation first. Watersheds where studies prerequisite to cleanup are occurring include the upper Anirnas River, Willow Creek (tributary to the upper Rio Grande), Chalk Creek (tributary to the upper Arkansas River), the Uncompahgre River, and the Alamosa River. During the inventory, evidence of naturally occurring water quality degradation was found in areas where little or no evidence of mining activity exists. These areas include the upper Alamosa River, the Middle Fork of Mineral Creek, Peekaboo Gulch, and Handcart Gulch. Water from these natural sources has been found to significantly exceed Colorado water quality standards for several metals.

Jan 1, 2000

By T. M. Karppanen

Shotcrete is used both in mining and tunnelling for supporting rock. Both dry and wet processes are used for shotcreting, and each produces good quality concrete. Thick shotcrete layers function as a concrete arch supporting loose rock. Thin layers prevent relative movements between the blocks of rock due to the fine concrete in the cracks and joints. No progressive fallouts occur since key blocks are kept in place. Rockbolts are often used together with shotcrete in order to create an arch around the tunnel making the rock to support itself. Shotcrete is sprayed either manually or by means of mechanized equipment. The aim is to spray required the layer thickness in one pass and with a minimum amount of rebound. Sprayed layers should also be as even as possible. The tip of the nozzle should be moved in circular movements. The shotcrete should be sprayed at a right angle to the rock surface; the optimum distance from the nozzle to the application surface must be found by experiment. In a mine shotcreting forms a materials handling system which includes batching, transporting and the actual shotcreting. The equipment used vary depending on the spraying method, mining conditions and the location of the mine. Shotcreting is performed with a purpose-designed unit in most cases where operation is mechanized. The shotcreting unit consists of a spraying machine with a hose and a nozzle, an additive system, a manipulator and a mobile carrier with all the necessary controls and accessories. The key element of the unit is the shotcreting manipulator which holds and guides the nozzle as required. The manipulators currently in use are hydraulically operated, and their remote controlled booms are also often called robots. These manipulators have enabled users to increase their output capacities, to remove the operator away from unsafe areas and from the influence of dust and rebound. Furthermore, they improve the shotcrete quality and reduce shotcreting costs.

Jan 1, 1989

By T. F. Deems

The nature, usage and comparatively rare occurrence of ball clay is described. The importance of these white firing plastic clays in ceramics, particularly in the production of industrial sanitary ware and tiles, is emphasized. The US deposits are briefly discussed. What is known about relevant deposits in Brazil, Argentina, Colombia and Venezuela (the four largest ceramic producers in South America) is also described. The ceramic plants have been sited near the centers of population rather than the plastic clay deposits. At present, extraction is probably concentrated on surface residual deposits and lenses which require minimum investment. Native plastic clays are used exclusively in the tile plants, but in sanitary ware, they are often used as extenders of imported ball clays.

Jan 1, 1997

By D. K. Grubbs

Red bauxites from Breadnut Valley, Clarendon Parish, Jamaica, are very homogeneous in texture. Bauxite minerals are uniformly distributed in a groundmass, the predominant grain size being smaller than l um (Figure 1 Although the deposits have a massive, non-stratified structure, they all seem to have been affected by postformational faulting which is evidenced by shear zones running subvertically through the deposits. These shear zones stand out very clearly because of a yellow staining along their faces. Often yellow zones, ranging from a few m to several cm in thickness, have developed. When the shear zones are cut at an angle, they appear as yellow veins. Near the surface of the deposits, yellow material forms shallow irregular lenses (Figure 2). In most cases, tree roots (hair roots), or their imprints, are associated with the shear zones or stained areas. In fact, the yellowish color is especially pronounced along these roots and often disappears where the roots end (Figure 3). The mineral composition and texture of red groundmass and yellow zones are markedly different. Secondary phosphate minerals and a higher goethite to hematite ratio characterize the mineral composition of the yellow zones. It should also be noted that Al-substitution in goethite from these areas is significantly higher than in goethite occurring in the groundmass (Figure 4).

Jan 1, 1980

By G. E. Wasson

Coal in most refuse ponds including those owned by Consolidation Coal Company can be recovered by froth flotation techniques. Laboratory studies show that the flotation conditions required for coal recovery varied greatly from pond to pond. The variables found to be most important for high coal recovery and low product ash were: a) the amount and type of flotation reagents and b) the degree of conditioning before flotation. Coal recovery at a rate of 0.504 kg/s (2 tons/hr) was demonstrated at a pond site employing a mobile froth flotation unit.

Jan 1, 1988

By V. E. Housman

EPA's Mining Waste Section within the Office of Solid Waste is continuing to collect and analyze information on mining waste management practices. Starting in 1991, the Mining Waste Section has continued to conduct site visits and prepare case study reports on the waste generation and management practices of operating mines. In choosing sites to study, a reasonable attempt was made to provide diversity in mining commodity types, geographic regions, geology, climate, and environment. To date, EPA has visited the following mines: Asarco Troy (copper) in Montana, Newmont Rain in Nevada (gold), Cyprus Thompson Creek (molybdenum) in Idaho, LTV Steel (iron) in Minnesota, Phelps Dodge Morenci (copper) in Arizona, Doe Run Fletcher (lead) in Missouri, Brewer (gold) in South Carolina, IMC Four Corners (phosphate) .in Florida, Pennzoil Culberson (sulfur) in Texas, Nerco Cripple Creek (gold) in Colorado, Copper Range White Pine (copper) in Michigan, Magma San Manuel (copper) in Arizona, Colosseum (gold) in California, and several gold placer mines in Alaska, including the Valdez Creek Mine. EPA has prepared a case study report on each facility. The mine operators were provided an opportunity to comment on their respective site visit report and their comments have been included in' each respective report. These site visit reports have in turn been incorporated into technical resource documents which provide a detailed description of each mining sector. EPA is currently reviewing the technical resource documents and plans to release the documents in the Spring of 1994.

Jan 1, 1994

By B. R. Addison

In the Spring of 1991, Georgia Marble Company of Arizona (GMCOA), acquired the Andrada Marble Company located near Vail, Arizona, approximately 32 km southeast of Tucson. The Georgia Marble Company operation consists of an open pit quarry and a recently constructed, state of the art calcium carbonate milling and processing facility. The open pit quarry exposes white, crystalline, CaCO3, Escabrosa limestone that meets our customer criteria for Consumer and Industrial Filler applications. The Georgia Marble Company Arizona Division facility is designed and engineered to produce a wide range of milled calcium carbonate that includes finely ground and coarse screened products.

Jan 1, 1994

By M. D. Baker

Coal-water slurry preparation requires fine grinding and cleaning of coal by flotation. Finer grinding leads to increased ball wear and its effect on the surface properties of coal becomes of concern. Marked ball wear tests were performed to study the effects of oxygen, pH, the soluble species of coal and the addition of pyrrhotite on ball wear. The synergistic action of coal and oxygen greatly enhanced the corrosion of mild steel balls during grinding. Electrochemical measurements on a mild steel electrode in coal slurries and SEM observations of grinding ball surfaces were carried out to explore the corrosive wear mechanism.

Jan 1, 1989

By Michael C. Montoya, Craig Hopper

It has been well established that the ability to soft start a conveyor will give many benefits to the conveyor user. The effects of deceleration on belt tension have not been as extensively studied. This paper presents the findings of field measurements on the belt tension of a conveyor undergoing various rates of deceleration. The control of conveyor drive motors by Variable Frequency Drives (VFDs) allows the conveyor to be controlled during both acceleration and deceleration. The conveyor is allowed to ramp to a stop without putting unnecessary stress on the belt or conveyor structure.

Jan 1, 2000