Search Documents

By W. C. Patrick

The Spent Fuel Test-Climax (SFT-C) was con- ducted to evaluate the feasibility of retrievable deep geologic storage of commercially generated spent nuclear-reactor fuel assemblies. One of the primary aspects of the test was to measure the thermomechanical response of the rock mass to the extensive heating of a large volume of rock. Instrumentation was emplaced to measure stress changes, relative motion of the rock mass, and tunnel closures during three year of heating from thermally decaying heat sources, followed by a six month cooldown period. The calculations reported here were performed using the best available input parameters, thermal and mechanical properties, and power levels which were directly measured or inferred from measurements made during the test. This report documents the results of these calculations and compares the results with selected measurements made during heating and cooling of the SFT-C.

Jan 1, 1986

By Richard Jr. Ray, Richard Druesedow

The Virginia Operations of Consolidation Coal Co. include a diversity of mine fan configurations which have been tested to quantify pressure losses through the inlet ductwork. Airflow and pressure measurements were taken at four shaft sites to calculate losses for the 90-degree bend at the top of the shaft and the self-closing dampers or closing doors located between the shaft and fan. Velocity contours were then developed from the test data to determine flow patterns in each fan system component. In addition, yaw and pitch angles of airflow through the fan annulus were measured to evaluate turbulence levels created by various inlet ductwork designs. The test results indicate that proper design of the shaft collar and ductwork arrangement for main mine fans can substantially reduce system pressure losses and air turbulence. BY minimizing the pressure drop experienced on the surface, these design improvements enable the bulk of the total pressure developed by the fan(s) to be utilized in the mine.

Jan 1, 1995

By B. J. S. Sceresini

The Filblast Cyanidation Process incorporates the advantages of intense high shear mixing, high dissolved oxygen concentra­tion and high pressure to achieve extremely rapid gold dissolu­tion rates. This is made possible without suffering from high energy or wear rates by the unique design of the Filblast gas shear reactor. The reactor is a rugged and compact in-line device which can be constructed from a variety of wear and chemical resistant materials. High temperature tolerance is also possible so that the device can be incorporated into a pressure leach circuit with significant capital cost savings because of the high capacity to volume ratio that is an inherent feature of the device. For cyanidation applications the outer casing is protected by a polyurethane coating and the internal parts are of wear resistant polymer. The largest unit built to date has overall dimensions of 1200 mm length by 300 mm diameter and has a capacity of about 150 dry tonnes per hour at 40-45 % solids. Service life at this throughput is at least three months. Six mines are currently employing the Filblast Process and another six are conducting plant trials. The ore types range from highly reactive, almost impossible to treat, pyrrhotite/ arsenopy­rite to deeply weathered clay ore which forms a highly viscous pulp. It has been found that the effect of shear thinning has resulted in improved leaching and adsorption kinetics resulting in higher carbon loading and reduced soluble gold loss. Total tonnage treated is approximately eight million tonnes per annum. This paper presents the operating benefits and cost savings which have been achieved in four plants, two treating oxide/ sulphide ore blends and two treating highly reactive sulphide ore and concentrate. Filblast leasing and maintenance charges and pump operating costs are about ten percent of the benefits. A conceptual cyanidation circuit based on the Filblast Cyanidation Process is also discussed. The Filblast System is an in-line pressure leach aerator/ reactor which generates very high shear and greatly enhances mass transfer rate by generating extremely small gas particles where oxygen gas is required for oxidation reactions and/or utilising the high shear characteristics to minimise the diffusion boundary layer. Both of these rate limiting factors effect the rate mechanism for gold cyanidation. Initially two multi-stage Filblast aerator cartridges formed a leach train but now the trend is to install a single submersible cartridge of equivalent perfor­mance. This design simplifies installation and minimises change-out times. However the in-line concept can be employed where high pressure leaching or pressure oxidation is required. The reactor is submerged in the leach tank so that the mass of gas micro-bubbles contained in the discharging slurry is entrained in the agitator vortex and is thoroughly dispersed throughout the tank. A diagrammatic representation of a leaching circuit incorpo­rating the Filblast Reactor is shown in Figure 1. The recirculation pump takes new feed directly from the cyclone overflow trash screen either under gravity or pump fed and recirculates the balance to maintain 250 - 270 m3/h total slurry flow. All of the leach feed slurry gets at least one pass through the Filblast thereby eliminating short-circuiting. Typically a 6/4 EAH Warman pump drawing 60-70 kW is required to circulate 250 m3/h through the system. The back pressure generated by the Filblast is in the range of 400-500 kPa depending upon pumping rate, pulp density and slurry rheology. The high shearing rate effectively negates the viscous effect of slurries and the addition of a gas further reduces the pulp density by virtue of the intensely aerated, homogeneous medium. The gold leaching Filblast cartridge elements are made of polyurethane but stainless steel, ni-hard, rubber or ceramics can be used depending on the operating temperature and design duty. The efficiency of the Filblast Leach Reactor in gold cyani­dation is due to the extremely efficient mixing, oxygen dissolu­tion and surface polishing action of the Filblast design. Either air or oxygen may be used but Atomaer recommend the use of oxygen because of the rate benefits gained from cyaniding at [02] significantly > 20 ppm D O in the reactor. Very high DO concentrations have been measured; in excess of 50 ppm. There is some debate as to whether the value is a true measure of the DO or the oxygen meter sensor is measuring the effect of a mass of very fine bubbles of free oxygen. Regardless of the fact the reactor has registered some amazing gold dissolution rates commonly in excess of 80 % during transit of the pulp through the reactor. The elapsed time is less than half a second!

Jan 1, 1995

By G. D. Naugle, L. C. Atkinson

Introduction Deep open-pit mines invariably affect the local and regional hydrologic systems. Pit dewatering, occurring during mining operations, puts an obvious hydrologic stress on these hydrologic systems. However, post-mining hydrologic impacts resulting from the pit refilling with groundwater following the cessation of mining activity can also be significant. The prediction of the rate at which the post-mining pit will fill with groundwater is a critical aspect of assessing the long-term hydrologic impacts. Numerical groundwater flow modeling provides a method for predicting the groundwater refilling rate of the pit. The rate at which pit "lakes" fill depends on several factors: •the rate and duration of pit dewatering; •the depth and size of the ultimate pit and •the pre-mining hydrologic regime. These factors can be incorporated into a detailed numerical groundwater flow model that can then be used to assess the effects of dewatering and post-mining recovery on the local and regional hydrologic systems. A sufficiently detailed, numerical groundwater model provides the oportunity to: •account for complex geology near the pit; •assess the impact of active pit dewatering and •predict the long-term impacts of post-mining groundwater flow into the pit. A detailed groundwater model incorporating these items has been developed and applied at an operating open-pit mine. Developed by Durbin and O'Brien (1987), the three-dimensional, finite-element, groundwater flow model was used to represent the hydrologic system of an approximately 253-km2 (98-sq mile) area surrounding the pit. Historical groundwater elevation data, stream flows and meteorologic, geologic and geophysical data were used to establish the dimensions and initial conditions for the model. Steady-state conditions, representing the pre-mining local and regional hydrologic systems, were simulated using the initial conditions incorporated into the groundwater model. The groundwater model was then utilized to simulate various dewatering programs, to predict the filling rate and the groundwater depth in the ultimate pit once mining activities are complete and to assess the long-term impacts on the regional groundwater flow system. Development of pit lake model Groundwater modeling efforts were completed in two phases. The first focused on pit dewatering activities, while the second phase concentrated on the post-mining effects on the hydrologic system. The final estimates of groundwater elevations calculated during the pit dewatering simulations were used in predicting the post-mining recovery of the hydrologic system. The groundwater model was also modified prior to the second phase to account for the volume of rock removed during mining activities. To account for the actual volume of rock mined, the geometry of the post-dewatering model grid was modified to approximate the final pit geometry. The depth and width of the ultimate pit were divided into eight idealized stages that represented significant changes in the bench geometries. These eight stages were then introduced sequentially into the model according to the predicted water elevations within the pit. In this way, changes in the volume and depth of water within the pit were accounted for through time. Once the ultimate pit geometry was accounted for in the model, it was necessary to assign new hydraulic characteristics to those parts of the model grid (elements) that represented excavated rock. The solution of the numerical model requires that finite hydraulic conductivity values be assigned to the portion of the groundwater model that represents excavated rock. Therefore, the calculated groundwater elevations differ, somewhat, between the edges and the center of the open pit. These model-calculated water elevations at the edge and in the middle of the open pit represent the elevation of water that would occur in the pit lake. To minimize the error in the estimated level of water within the pit lake, the hydraulic conductivity was increased to a value that would: •minimize the predicted difference between the groundwater elevations across the open pit and •produce a numerically stable solution. Specific storage is the hydrologic parameter that accounts for the water produced by compaction of the aquifer matrix. To predict the groundwater volume that would flow into the ultimate pit, this parameter was assigned a value equivalent to the compressibility of water. This value of specific storage reflects the post-mining groundwater storage occurring as an open body of water. Additionally, a specific yield of 1.0 was assigned to the pit elements to represent the 100% porosity of the open pit. In

Jan 1, 1994

By D. Royston

Curved pulp lifters have been incorporated in SAG and AG mills in Australia. The aims have been to ensure complete discharge, at high throughput, of both slurry and coarse solids, especially at high mill rotational speeds. Curved pulp lifters can overcome incomplete discharge and back-flow of solids down the pulp lifter that can occur in straight-radial pulp lifters (and is a major cause of wear). They can be designed to prevent reverse flow of pulp via grates back into the mill. Experience with curved pulp lifters now extends to three years over three mills, in one mill as an installation from new and two as retro-fitted installations. Curved pulp lifters, relative to conventional designs, offer improved discharge and wear performance and well as high impact-resistance and wear life of the curved pulp lifter grates.

Jan 1, 2000

By R. N. Chakravorty

It is well established that coal can react with oxygen in air at ambient temperature and as a result heat is produced. If the heat is not fully dissipated the temperature of the coal mass will increase, thereby enhancing the rate of oxidation with a greater production of heat. If this phenomena continues, the coal mass can ignite under favourable heat accumulation conditions. A number of mine fires are caused each year due to this phenomena, commonly known as spontaneous combustion. The early detection of spontaneous combustion is of prime importance to mining engineers since any fire which could be detected at an early stage may save the mine from considerable damage and subsequent loss of production. Obviously, there is no single general criteria by which one can assess whether the under- ground mining of a coal seam will result in liability to spontaneous combustion. This has made it imperative to develop systems for the early detection of heating and to follow its development. In recent years considerable advances have been made in the design and development of methods for the early detection of spontaneous combustion. The Mining Research Laboratories (CANMET) is presently investigating the problem of spontaneous combustion in coal mines with Kaiser Resources Ltd. at their hydraulic mine at Sparwood, B.C. on a co-operative basis, and some of the work was described earlier in the Canadian Institute of Mining & Metallurgy Bulletin (1,Z). This paper summarizes and updates the work done by CANMET on the detection of spontaneous combustion in coal mines.

Jan 1, 1980

By John P. Fillion

This paper will present an overview of conveyor haulage systems. Technical and economic feasibility will be examined as conveyor haulage is applied to large western surface coal mines. Theoretical analysis and actual cases will be presented from NERCO Coal Corp. experiences in bringing this application to their Western mines.

Jan 1, 1989

By F. Seymour

A dynamic programming algorithm is presented that takes a series of nested phases, a fixed mining-rate schedule and a fixed plant-production-capacity schedule, and, from these, finds the mining and cutoff grade sequence that maximizes the net present value. This tool allows the mining engineer to quickly look at project sensitivity to various production capacities, commodity prices and costs. A description of the algorithm is given along with examples of how it has been used at Newmont Gold.

Jan 1, 1996

By V. Rajaram, D. P. O’Connor, L. Sakamoto

In 1988, the Metropolitan Water Reclamation District of Greater Chicago (MWRD) imposed a no-blasting specification (blasting is restricted to the construction shaft and shaft bottom or boot) on the Deep Tunnel project. This was prompted by numerous complaints from residents in the vicinity of the project and controversies experienced on previous projects from blasting the rock overlying the tunnel. This paper will describe the methods used by two major contractors driving 20 km (12.5 miles) of tunnel, and drilling more than 36 shafts under this restrictive specification. The impacts are detailed on design, construction, schedule, cost and the environment.

Jan 1, 1993

By P. Somasundaran

The use of chemical additives in ultrafine grinding will be reviewed in this paper for the case of grinding of quartz in solutions of surfactants and inorganic electrolytes including some dispersants under different conditions of pH and ionic strength Mechanisms are examined by correlating the grinding effects with those obtained for the influence of these chemicals on zeta potential, pulp fluidity and flocculation/dispersion characteristics The analysis suggests grinding depends mainly on the state of aggregation of the ground products inside the mill and pulp fluidity Implications of the observed effects on ultrafine grinding in general are discussed

Jan 1, 1983

By W. P. Stroud, R. S. Dennen

A ground penetrating synthetic pulse radar system has been used by the US Bureau of Mines to probe into a coal pillar to locate hidden structures or anomalies. Direct matrix inversion was used to obtain a velocity image of the interior of the pillar. The reconstructed image showed the existence and location of a relatively low velocity material within the pillar. Core samples were taken from the pillar in a region surrounding the low velocity material. Analysis of the cores showed the presence of a clay vein coinciding with the low velocity material imaged in the tomogram.

Jan 1, 1992

By C. M. Marquardt

The materials handling systems in the large concentrating plants have required the employment of a considerable number of workmen, many of whom had very little to do except to act as watchmen to avoid bad spills at belt junctions and to operate tripper cars, shuttle belts, etc. Much time also was spent in watching bins to make sure they were properly filled. Approximately four and one-half years ago the author, Yin coopera¬tion with the engineering and supervisory personnel of The Anaconda Company at Anaconda, Montana, began to give this problem serious consideration. Prior to this the author had developed, at the request of The Anaconda Company, a transistorized resistance-sensitive probe relay system for detecting the level of ore in bins. With this system cables or chains were suspended from insulators above the bins and were of suitable length to determine the elevation of the ore in the bins.

Jan 1, 1962

By H. Suharyono

The results of an experimental study of polymer-induced flocculation of clay suspensions in continuous, stirred-tank reactors are presented. The effects of polymer dosage, mixing time and mixing intensity are shown to be generally similar to those observed for equivalent batch systems, but flocculation appears to be generally less effective in the continuous process. Settling rates are lower and supernatant turbidities are higher for the continuous system. It is postulated that non-equilibrium effects due to simultaneous polymer adsorption and floc growth can be exploited so as to enhance flocculation in batch systems. The nature of the continuous process, however, offers less opportunity for taking advantage of such effects. Conditions in a continuous flocculation system inherently lead to a closer approach to equilibrium.

Jan 1, 1994

By Frank F. Aplan

Coal flotation offers the promise of a highly effective, large tonnage, low cost means of cleaning fine coal. Unfortunately, it has, to date, not lived up to its promise. Several problems that need to be addressed before coal flotation can achieve its promise are discussed and possible solutions offered.

Jan 1, 1989

By H. Pieterse, K. S. Fraser, J. R. Goode

The Goldstrike autoclave plant is designed for the pressure oxidation of 1363 t/d (1500 stpd) of refractory gold ore. The plant was commissioned in early February 1990 over a one week period - an unusually short period for a plant of this complexity. The rapid plant start-up is attributed to certain detailed design and control aspects of the plant. This paper discusses key features of the autoclave plant with emphasis on the design of the splash/flash system of heat recovery and the control systems. Commissioning and plant operations over the first three months are reviewed.

Jan 1, 1990

By P. Mousset-Jones, F. Calizaya

Currently, a 4.3 km long drift is being developed on the 3440 level in the Lower Kalamazoo project at the San Manuel Mine, Magma Copper Company, AZ. The drift, located at 1050 m below surface, is being constructed using a 4.6 m diameter tunnel boring machine (TBM). The drift is ventilated by a forcing type auxiliary ventilation system. At the face, to mitigate the impact on the work environment of the TBM, the system is equipped with dust extraction and refrigeration systems. Recently, to evaluate the ventilation conditions in the drift, a continuous monitoring system has been installed. The system can be used to measure the air velocity, barometric pressure, relative humidity and air and rock temperatures. This study describes the capabilities and limitations of this system, and presents a summary of the results.

Jan 1, 1995

By K. R. Price, M. Gauna

Jim Walter Resources No. 4 mine produces coal through retreat longwall mining at 610 to 670 m (2000 to 2200 ft) of depth. A three entry, total yield pillar, longwall development experimental region was established for three adjacent longwall panels utilizing 6.1 m (20 ft) wide gate section pillars. Presently, the first longwall panel is completed with roadway deformational behavior monitored for a ground control assessment of the mining system. Data illustrate that the total yield pillar gate section design at No. 4 mine is presently comparable to gate section designs having large equal size chain pillars. Ground conditions will continue to be monitored during the mining of subsequent longwall panels in order to determine the ground control implications from multiple panel extraction.

Jan 1, 1986

By Roderick K. Davey

Kennecott Copper Corp.'s Metal Mining Div. operates three major open-pit copper mines in the western United States. These operations include Utah Copper Div., Ray Mines Div. in Arizona, and Chino Mines Div. in New Mexico. At each of these operations, the material is loaded by large electric shovels and transported by both truck and rail haulage. In 1977, 197 350 774 t (217,542,000 st) of ore and waste were mined at these operations, and 302 040 t (332,942 st) of copper were produced. Also a significant amount of molybdenite was produced as a byproduct. In operations as complex and large as these, there is an inherent need for up-to-date reports concerning how much material was mined during the previous day, and year-to-date, what equipment is scheduled for maintenance, how equipment has been performing, etc.

Jan 1, 1979

By Nora M. Hutt, Kevin A. Morin

One technique for controlling ongoing acidic drainage is to relocate and submerge net-acid-generating waste rock in a lake or water-retaining impoundment. This can lead to the overall improvement of water quality and the reduction In short-term environmental liabilities. A case study of this technique is the Eskay Creek Mine in northern British Columbia. Some findings of the study are: (1) the addition of lime to each truckload of rock, based on its rinse pH, neutralized the accumulated acidity and suppressed the accumulated-metal release, (2) only 10-20% of the dump's neutralization potential had been consumed when acidic drainage appeared, (3) water chemistry in the watershed recovered roughly three years after relocation, and (4) environmental liability was reduced due to the cessation of on-land acidic drainage with no degradation of lake chemistry.

Jan 1, 2000

By P. K. Davis, B. Gharib

The results of a previous basic study of the flow and design characteristics of hydrocyclones demonstrated that a recovery as high as 99% with a product rating* of 0.95 can be achieved on a batch+ basis with a single, water-only cyclone if it is configured properly. The next logical step was to demonstrate continuous processing of gob for the efficient recovery of coal by means of a laboratory-size demonstration system. A project to design and construct such a single-¬cyclone system was sponsored by the US Department of Energy, which also sponsored the initial study. A recovery of 93% with a product rating of 0.89 was demonstrated. The system design and the data taken are discussed.

Jan 1, 1990