Search Documents

By J. Slivnik, A. Stergarsek

[The site] [Z]irovski vrh uranium ore deposit is located in the extreme north-western part of Yugoslavia, some fourthy kilometers from the capital of Socialist Republic of Slovenia, Ljubljana, not far from the Italian and Austrian border. The sandstone type deposit of uranium ore with medium grade is located in a foothill of Julian Alps. The site shows some typical conditions for this region, which demand special attention in respect to the incorporation of an uranium treatment facility into environment. Among these specific conditions the following site characteristics should be mentioned: - populated area of agricultural and recreational value, - unconvenient climatic conditions with excessive rainfall and long lasting temperature inversions in the winter time, - very pure surface and underground waters which supply the drinking water reservate for large area including the capital of Slovenia, - sharp relief, - unconvenient geological structure. The choise of technology The intention to produce uranium and at the same time respecting the natural characteristics and existing uses of the site made the design of the ore treatment facility relatively difficult one. In general, there were two basic alternatives available perform the task. First alternative was to adopt the usual technological flowsheet with wet tailings disposal and with discharge of used water i.e. liquid effluents into the river. In order to prevent the negative impact of such technology on the sourrounding area sophisticated water purification installation and costly measures in wet tailings disposal e.g. impermeabilisation of large areas by concrete injections, large dam constructions, uncertain capturing of the water sources should be employed. Second alternative was to modify the usual flowsheet by employing the maximal recycling of liquid effluents to the process and to dispose the solid

Jan 1, 1980

By R. R. Jozefowicz, T. X. Ren, J. S. Edwards

The control of methane emission into underground mine workings is important both for the safety and productivity of the mine. As deeper and gasser coal seams are mined, ventilation methods involving increasing air pressures and quantities across mine workings may not be able to cope consistently with methane emission rates during the production cycle. An accurate prediction of methane emission into mine workings is of great significance in the design of ventilation systems and additional methane control methods if required. Research has been conducted to develop a numerical method for simulating methane flow through strata in which permeability is strongly influenced by mining-induced stress. To achieve this objective, both numerical modelling using Computational Fluid Dynamics (CFD) and laboratory tests on rock samples and granular materials under triaxial stress condition were carried out. Correlation has been established between stress and permeability characteristics of rock-measure rocks and laboratory results are being incorporated into the CFD models. This paper introduces the use of CFD techniques to model methane flow through permeable strata around longwall coal faces currently undertaken at the University of Nottingham.

Jan 1, 1997

By Y. Théberge, V. Svalbonas, M. Fresko, E. Stopper

For many gearing applications, calculations carried out to AGMA standards are comprehensive. For very large gears, the elastic nature of the gear and pinion structures begins to play a larger role in determining the load distribution along the teeth. Various factors affecting the stiffness of the gear and pinion sets have been studied through FEA models for actual configurations. In particular, the effect of gear shape, load location, unsymmetrical structures, etc. have been studied in the unaligned and field aligned conditions. Analysis results show that the load distribution factor is highly sensitive to pin-ion stiffness, which affects gear structure design.

Jan 1, 2004

By R. Hogg, M. Polat, S. Chander

A fresh dust generator was designed and built in order to study the agglomeration behavior and other characteristics of freshly generated airborne dust. The size distribution of the freshly generated quartz airborne dust produced by the generator was measured both directly in air and after dispersion in water. It was observed that same dust particles had an apparently coarser size distribution in air than in water, suggesting possible agglomeration of the dust particles. It was also observed that the size distribution obtained by a cascade impactor was very similar to the liquid dispersed size distribution, implying deagglomeration by the impactor. The agglomeration was confirmed by microscopic observations of particles in air and those collected on a microscope slide. The extent of agglomeration played a decisive role on the fraction of the dust actually becoming airborne. It was also found that contamination of the airborne dust by the rolls of the crusher was almost twice as much as that of the product.

Jan 1, 1991

By K. Fuenkajorn, J. J. K. Daeme

Ring tension tests have been conducted on 229 mm (9 in) diameter disks of Grande basaltic andesite and Pomona basalt with various center hole sizes in order to study the relationship between ring tensile strength and relative hole radius (hole radius/disk radius). The tensile strength, [ ] decreases as the relative hole radius, [ ] increases. A power equation, [ ] where C and R represent the coefficients of strength and shape, respectively, adequately represents the ring tensile strength as a function of relative hole radius over the range investigated. This equation can be used to distinguish the effect of the hole size from the strength results, to predict the tensile strength of a ring sample containing arbitrary hole sizes, and to approximate the critical relative hole radius of the material tested.

Jan 1, 1986

By S. A. Jeric

In-pit crushing and conveying of waste has been utilized in the mining industry for over 30 years. In recent years, innovations in crushing, conveying, and particularly waste and leach stacking technology have sparked a renewed interest in continuous haulage systems for large-scale open pit applications. A review of the advantages/disadvantages and operating techniques of crushers, feeders, conveyors, and stacking systems currently available is made. The paper examines some operations that are currently using large scale continuous haulage systems. Finally, a case study is presented that evaluates the application of a continuous waste haulage system in a large open pit mine in the Western United States, The case study includes a economic comparison with the existing truck haulage system.

Jan 1, 1997

By Staff

Assembling consistent data for a 40-year time series is a challenge because of the many changes that have occurred in this period. In many cases, because of process improvements and consumer requirements, grades of materials change in a 40-year span. This can lead to a wide fluctuation in price data simply because of increased costs for premium grades. Sources for obtaining price data can also change during a 40-year period. Changing the data source also introduces anomalies in a time series. In some cases, published price data are not representative of the real value of the material and provide little basis for further analysis. For some industrial mineral commodities, there are only a few producers, and value and production data are considered proprietary. In the data presented in this chapter, every attempt was made to ensure that the data were as consistent and representative of the industry as possible. However, the factors mentioned above may have introduced inconsistencies in some of the data series. Many different factors influence trends for industrial minerals because of the diversity of end uses for these commodities. Trends in production and prices for most of the industrial minerals can be related to one or more of the following: changing demand or technologies in end-use industries, development of new end uses, the effect of environmental regulations, production and processing technology changes, energy costs, foreign competition and substitution by other materials, and production as a byproduct of other minerals. World economic conditions, such as recessions and inflation rates, also play a part in some production and price trends. Data for 40 years of production for industrial minerals in the United States are presented in [Table 1] in 10-year increments. Unit values for the industrial minerals, in actual and constant 1990 dollars, are shown in [Tables 2 and 3].

Jan 1, 1994

By F. C. Nicolli, J. P. Barbosa, P. S. M. Soares, A. V. Estevez

INTRODUCTION Spent household dry cell batteries are frequently disposed of with metropolitan wastestream (MSW) in landfills where they can leak due to handling or aging. Frequent rain and sun cycles, especially in tropical environments, coupled to the action of leachate, dissolve their metal constituents which will eventually reach rivers, lakes and underground water. It is well known that some of these metals are fundamental to sustain life and that is why living organisms concentrate them through their metabolism, but it has been also recognized that beyond specific limits they can definitely be deleterious to the environment. In other words, high concentration of heavy metals are proven to cause chronic or acute diseases and toxic reactions, by acting on mammals' kidneys, liver and nervous system. In addition, some metals frequently used in household batteries, as mercury and cadmium, are said to be carcinogenic (Landis et al. 1995, Silva et al. 1988). Occasionally, plants to treat MSW are coupled to compost production. Household batteries present in MSW can be dragged into these plants, contaminating their products and eventually reaching vegetables making them not proper to consume by people and animals. Alternatively, batteries are also conveyed to incinerators and burned, throwing into the atmosphere volatile species. These can either act as contaminants as toxic vapor species or be delivered by winds and scavenged by rains contaminating soils and water far away from their source. In conclusion, despite the treatment applied to MSW, one can say that battery residues are potentially environmentally hazardous. The careful assessment of the environmental impact caused by residues of household batteries it is not an easy task and it can be referred as a multivariable problem. First, many different household batteries are produced by industry and the potential environmental hazard associated to their disposal depends primarily on the type of battery and manufacturer's technology. These characteristics will dictate how resistant the battery case is to handling and the

Jan 1, 1998

By William G. Davenport, Eric H. Partelpoeg

Direct smelting of copper in a single vessel has long been the extractive metallurgist's dream. Such a process offers the important advantages of (i) maximum use of the energy available from oxidizing the sulphur and iron of the concentrate; (ii) restriction of SO2 emissions to a single constant-strength source; (iii) minimum materials handling and (iv) elimination of at least one process step. Extensive developmental work was carried out in the 1960's and 1970's to implement such single-step processes. Some of the processes reached the prototype stage and it appeared that copper smelting technology was on the threshold of a new, efficient, minimum-pollution era. Since that time, however, the forward thrust has slowed and single-step smelting is still a process of the future. The paper describes in detail the potential advantages of single-step smelting; its history and current status; and the reasons why it has not been adopted industrially. It concludes that the potential benefits of single-step smelting are powerful and that many of the difficulties encountered in the 1970's will be overcome in the 1980's.

Jan 1, 1985

By C. P. Lazzara, F. J. Perzak, C. C. Hwang, C. D. Litton

Fire development and spread along conveyor belts in ventilated ducts were investigated experimentally and theoretically. Various types of conveyor belts used in mining applications were ignited and burned in a full-scale gallery under various flow conditions. The flame spread rates depended strongly on the ventilation air speed. The time-temperature traces of gas and belt obtained at 12 feet from the entrance show that a rapid belt surface temperature change takes place prior to a change in the gas temperature, indicating that radiative heat transfer from the flame to the belt surface plays an important role. Further, anomalies in the flame spread rate in the vicinity of 1.5 m/s air speed (i.e., much greater rate than that observed at either higher or lower speeds) can be explained through the mechanism of flame tilt and the resultant view factor between the flame surface and the belt surface. In order to correlate the fire spread with material properties of the conveyor belts (such as the specific heat, the thermal conductivity, and the pyrolysis temperature) and the fire environment (such as the gas temperature and the ventilation air speed), a theoretical model has been developed. This model is based on the experimental observation that the radiative heat transfer is the dominant mode of energy transfer ahead of the flame front. Agreement between the theory and the experimental results is good.

Jan 1, 1991

By Robert Dimock

The successful management of large dispersed mineral operations is dependent upon accurate and timely decision making. The plant locations providing the data to support the decision making process are generally separated by distances which elongate the time required to accumulate the data at a central focus. The need exists to examine operational data in context with total mining operations, and in relation to target projections and historical trends. The use of microcomputers for local information tasks is an established capability. Grouping microcomputers into local-area networks is rapidly becoming established. Interconnecting multiple local-area networks to provide a free flowing stream of information between all operational locations of a mining enterprise is possible with use of some emerging technologies. The benefit of the potential interconnections and rapid transfer of information can readily be seen from a production reporting perspective. Numerous other advantages exist' by providing routing to enable a workgroup to be established between separated work functions.

Jan 1, 1989

By J. J. Moore, B. Mishra, D. L. Olson

The production of radioactive and reactive metals, such as plutonium, uses various pyrometallurgical techniques that generate significant quantities of waste salts contaminated with hazardous, reactive or radioactive materials. Health concerns, environmental regulations and economic considerations require proper mitigation processes to recover the valuable components and for recycling or unrestricted release of these salts. The Oxygen Sparging Process converts soluble metal halides, such as chromium-, plutonium-, cerium chlorides, into insoluble oxides and/or oxychlorides which can be consolidated and separated for long-term storage or further processing. The matrix salt phase, viz. calcium and/or alkali chlorides, are clean after oxygen sparging and fit for recycling. This method has been described and its optimized parameters discussed to show that RCRA regulated elements, such as, chromium, lead, cadmium, etc. report to the consolidated phase making the salt recyclable. Salt Scrub Reduction Process for the recovery of radioactive and RCRA metals from the waste salts has been developed. The process uses a Ca-Ga intermetallic alloy which recovers over 98 percent of the reactive metals. The matrix salt phase in this process, viz. calcium or alkali metal chlorides, are clean after salt scrub reduction.

Jan 1, 1995

By G. L. Bloomsburg, E. G. Zahl

INTRODUCTION During the past decade, disposal of mine and mill waste material has become an increasingly important issue. Problems of structural stability and seepage effects on stability have been well addressed, and significant technological advances have been achieved [(1-4)]. The primary problem currently facing industry in the waste disposal area is environmental protection. The greatest environmental concern is over the amount of seepage or leachate entering the ground or surface water systems. Methods to determine the quantity of water seeping from a tailings pond have also been covered in the literature [(5-23)]. However, much further work is necessary to fully implement these techniques to evaluate tailings pond performance and accurately predict the various influences of disposal management on seepage from mill tailings. This study is an effort to develop those necessary techniques. The partially saturated method of analysis which is discussed here is applicable to most situations involving seepage from waste piles. In a conventional type of tailings pond, a slime layer is ordinarily built up under the ponded area. This material will consolidate slowly from capillary pressures and the weight of material deposited above it. In situations where this consolidation results in a slime layer of lower permeability than the native foundation soil, a partially saturated flow condition will usually exist in the native soil. This will result in a smaller quantity of water entering the ground-water system than would be predicted by saturated flow analysis. The finite-element program used in this study was originally developed by Neuman [(17)] and is called UNSAT2. The program will analyze problems of saturated or unsaturated, steady or nonsteady flow and can be used with a variety of boundary conditions such as constant flux, constant pressure, maximum flux, minimum pressure, and with infiltration, evaporation, and seepage surfaces. The maximum conditions are controlled by exterior factors such as atmospheric conditions; but the actual flow in the porous media is determined by properties of the porous media. In this test, the computer code was used

Jan 1, 1980

By Eric Leung, Stephen G. Hardcastle, Andrew Dasys

In today's economic environment, Canadian mines can ill afford to neglect their ventilation systems as they can consume 30- 40% of the electricity used in underground mines. In addition, Canadian mines can incur significant heating costs. For mines to be their most cost efficient they must embrace existing and emerging technology to optimize the use of their air; namely, maximizing its work in diluting and removing pollutants, limiting leakage, and avoiding the unnecessary consumption of costly fan pressure all the while ensuring the health of their workforce. Furthermore, in Canadian mines which are heavily dieselized there is great interest within the industry to convert from a rigid quantitative approach to ventilation, based upon engine size, towards a more flexible qualitative approach that provides credit for Clean engine technology" and permits ventilation supply to be driven and based upon pollutant demands. In the future, there is even the possibility that ventilation will only be required to supply oxygen to diesel equipment as the underground hands-on workforce is replaced by surface workers and tele-operation. Such changes will allow mine operators to minimize their electrical usage and operating costs, for in its simplest form the cost of running a fan is proportional to the quantity3; therefore, reducing current ventilation demands or limiting increases brought on by more stringent legislation, can produce very significant cost savings. CANMET, through ventilation surveys and use of its modern 3D-CANVENT ventilation simulator, have been demonstrating to the mining industry how ventilation can be optimally delivered at reduced costs. El-Equip with their leaky-feeder communications and MultiVENT monitoring and control system have facilitated mines to control fans and hence costs, and also monitor such ventilation parameters as pollutant concentrations. These two parties are now combining their efforts to develop an integrated air management system which will be demonstrated at CANMET's Experimental Mine Val D'Or, Quebec. With such an air management system, the ventilation engineer will have: 1) a simple to use simulator to design and test ventilation scenarios; 2) remote controls of fans, doors and regulators to implement changes; and 3) real-time monitoring of airflow, pollutant concentrations, and both vehicle identity and location to show whether changes are necessary. It is only when all three are available, that a mine's ventilation system can be operated at minimum cost.

Jan 1, 1997

By A. Zorychta, T. Cyrul, Z. Kleczek

INTRODUCTION Underground mining causes disturbances of the primary state of stresses. Resulting from those disturbances a loss of stability of rocks that surround excavation may occur interrupting the production and creating life danger for the personnel. One of the manifestations of such an instability is a rock burst phenomenon which mainly occurs at great depths. From the mechanical mint of view the rock burst is a loss of stability /Filcek et a1.,1984; Pietuchow and Linkow, 1976/ due to : - quasi-static stress changes in the surrounding rocks; we will call it s seam burst , - dynamic stress changes in the surrounding rocks caused by rock shocks ; we will call it roof burst. Possibility of the rock burst occurrence Is uniquely determined by the state of stresses existing in the rock mass. In the following sections of the paper we will consider different aspects of this question. Moreover distributions of displacements and failure criteria for a coal seam at longwall mining will be defined. STATEMENT OF THE PROBLEM Determination of the vertical stresses and displacements resulting from longwail mining will be based on the Budryk’s idea of a stress wave /Salustowicz, 1955/. The idea originates from the analysis of a roof plate /beam/ resting on the deformable foundation /Sean/ and subjected to the cylindrical bending. Equation of the bending lice uniquely defines vertical stresses and displacements which are induced in the seam. The equation will account only the shear force effect. Elimination of the bending moment has been shown and discussed by Zorychta and Bcrecki /Zorychta, 1985; Borecki and

Jan 1, 1986

By M. S. Klima

Proper analysis of washability data can lead to the development of a maximum yield coal preparation plant flow sheet. Simulations, as simple as spreadsheet mass and water balancing, are important in examining yield maximization and middlings liberation. Key to such attribute tracking flow sheet simulations is the distribution model, expressing the probability of a species reporting to the product stream. There are many such models in the literature. This paper examines a functional form that can represent or fit most of the proposed distribution functions.

Jan 1, 1997

By Z. Yu

The effect of particle size on coal dewatering has been well recognized However, there are no systematic studies on ultrafine coal dewatering. The results discussed last year revealed the effect of flocculant type and coal wettability on the filtration of ultrafine coal In this paper, the differences in dewatering between -25 µ m ultrafine and -500 µ m fine coal with addition of flocculants, surfactants and oil-emulsions in vacuum filtration are further investigated Significant differences were observed in the reduction of the cake moisture. The utilized emulsions were found to be very powerful and promising filtration aids for both ultrafine and fine fractions of hydrophobic and hydrophilic coal

Jan 1, 1995

JIM ARNOLD: Questions? Comments? Gary, were you gone when I made the comments about corporate puke? [laughter] SPEAKER: You were hiding. BRUCE CAVENDER, BHP Copper: Having worked in both places, I'd like to address the issue of the plant versus the corporate office. One thing to keep in mind is that we are all very engaged with the technical elegance of a lot of the work we do. There's some tremendous technical expertise in the plant. But remember, the guys in the corporate office are only thinking in one denomination, and that's dollars. So we'll see something like a spill, and for us it's a problem. At the end of the day, what the corporation cares about is the financial impact. So we've got to be careful to couch our solutions in dollar terms. JIM ARNOLD: Rebuttal? [laughter] DOUG HALBE: Are you going to rebut this one, Andy? ANDY CARTER, Oxidor Gold Corporation: No, I don't think so. I'm not up to it. I'd just like to address a question both to our panel and the floor. Those of us who've been in this industry any length of time have seen these same mistakes made over and over again. Wherever you go, year after year, plant after plant, you see the same problems. I guarantee you, Doug, that if we have a similar conference down the road, you're going to see the same thing. My question to the panel and to the floor is what is it about our industry that stops us from learning from our mistakes? What characteristic is it that prevents us from learning and makes us repeat the same mistakes over and over again? DOUG HALBE: That's a great question. Someone said in a meeting 10 years ago that if the people who design plants designed airplanes, the planes would be falling out of the air all the time. GARY SIMMONS, Newmont Gold Company: I've got an answer to your question as to why many plants are poorly designed. It's that the minute anybody demonstrates any sort of competence in plant design, they're promoted to a higher-paying job, and the talent pool is left with people of lesser experience. Just think about it: The people who have the experience and have demonstrated it more than once have moved up. JIM ARNOLD: I think that there's another reason, too. Seven or eight years ago I was chairing a session, and I challenged everyone in the session to some day publish an article about the design mistakes they'd made because we never talk about our mistakes. I'll

Jan 1, 1998

By Raja V. Ramani, Sachin Shankar

Re-entrainment refers to dislodgement of particles deposited by both atmospheric and nonatmospheric processes and their subsequent insertion into a flowing field. Formation of sand dunes, snow drifts, soil erosion and fugitive dust emissions are a few examples of the natural occurrence of re-entrainment. Re-entrainment studies have been done for the estimation of potential hazards from nuclear fallouts. The phenomenon of re-entrainment has been utilized for the cleaning of wafers and filters. Re-entrainment is associated with both surface and underground mining activities. However, studies on dust re-entrainment in mine atmospheres are limited. Understanding the re-entrainment phenomenon is important because dust particles lying seemingly harmless on the ground and adhering to numerous surfaces can get re-entrained and become a health and safety hazard. There are significant differences in the kind of re-entrainment encountered in underground mines and those in other fields of interest. These major differences are air velocity, direction of air flow, particle size, amount of particles, and time of exposure. While numerous studies have been done in other fields to identify the role of interacting variables and their contribution to the mechanisms of re-entrainment, no similar reported work is available for dust in mine atmospheres. In this paper, recent research efforts on re-entrainment are reviewed. The most suitable form of representing re-entrainment in underground coal mine atmosphere is presented. Various approaches to studying re-entrainment phenomenon in mines are also outlined.

Jan 1, 1991

By James D. Bennett, David L. Passmore

The Coal Mining Section of the National Safety Council has selected hand and finger injuries of coal miners as a major topic for safety policy analysis [Tinney, 19851. So that facts about hand and finger injuries can be used to guide the Committee's work and the work of policy-makers, we present in this paper detailed analyses of the following factors related to hand and finger injuries received by coal miners between 1975 and 1983: occupations of the injured miners; activities of the miners when injured; machines involved; objects, substances, exposures, or bodily motions that produced or inflicted the injuries; principal physical characteristics of injuries; and events directly resulting in the injuries. We analyze hand injuries for underground and surface mines separately because of the remarkably different production methods and hazards evident in these two operating environments. We do not, however, provide information about hand and finger injuries that occurred in surface operations at underground sites (such as yards, shops, or tipples), auger mining operations, culm banks, dredging operations, mill or preparation plants, offices, or laboratories. The most comprehensive information about the safety of coal mining in the United States is assembled by the Health and Safety Analysis Center (HSAC) of the Mine Safety and Health Administration of the United States Department of Labor. Mine operators in the United States report to HSAC all injuries as required under Part 50, Title 30, of the Code of Federal Regulations (mandated by Section 103 the Federal Mine Safety and Health Amendments Act of 1977, Public Law 95-164). These regulations stipulate that injuries must be reported within ten days of their occurrence on a United States government data collection form, Mine Accident, Illness and Injury Report (MSHA Form 7000-1). HSAC maintains these data primarily to produce federally-mandated reports. HSAC resolves injury reports that are incomplete, checks for errors in data coding and handling, and corrects inconsistencies in data submitted by

Jan 1, 1986