Search Documents

By T. A. Toney

With new lightweight designs, spirals have become standard equipment in coal preparation plants worldwide. To their credit, spirals typically show very low coal losses to the refuse stream under most operating conditions. However, spirals do tend to separate at cut points in excess of 1.80 S.G. Attempts to obtain lower cut points have typically resulted in coal losses to middlings. Middlings retreatment with secondary spirals is therefore becoming common place. Other forms of retreatment with water-only cyclones, hydrosizers, and recirculation have been attempted with some success. This paper reports on a novel (Patent Applied For) approach to retreating spiral middlings m a heavy-media-cyclone circuit.

Jan 1, 1998

By W. R. Dearman, N. Turk

A seismic fissuration index (K) is defined as the ratio of the difference in the P and S wave velocities obtained when a dry rock specimen is tested both under a load equal to half the uniaxial compressive strength of the rock (Vo) and without an applied load (Vd) to the velocity obtained without an applied load (Vd), as K = (Vo - Vd)/Vd. A similar seismic fissuration index is also proposed for classifying the dry rock mass in terms of field seismic velocities. The field equation is extended by including the intact rock seismic velocities. K is found to be related to the porosity of rocks. The proposed equation can equally be used for characterizing saturated rocks, using S-wave velocities. However, the time average equation should be used for characterizing saturated rocks, using P-wave velocities, even though this equation gives upperbound estimates of the rock material and fracture porosities.

Jan 1, 1986

By Alden B. Carpenter

The Dead Sea is the only relatively large body of surface water having bromide concentrations comparable to those in the brines of the Smackover Formation in Arkansas. The Dead Sea, like the Smackover brines, contains a great deal of calcium and is very low in sulfate and iodide. The relationships between potassium, divalent cations, and chloride indicate that over 20 percent of the bromide in the Dead Sea is derived from some source other than by the evaporation of sea water. A similar type of study of the Smackover brines in Arkansas indicates that approximately 60 percent of the bromide has been derived from some source other than sea water. Both the Dead Sea and Smackover brines are very low in iodide suggesting that the excess bromide has not been derived from organic matter. The origin of the excess bromide is probably the same for both of these brines, but the source of this bromide remains unknown.

Jan 1, 1978

By Todd L. Hollingsworth, Jeremy K. Hobbs

In 2001, the Radomiro Tomic Mine located near Calamq Chile, added a tertiary crushing facility. An 84" wide mobile tripper is used to fill their tertiary crushing storage facility. This paper is a we study to demonstrate the drive and control systems in use on the tripper. Of special note is the design concept used to allow the system to operate multiple motors in both demand and regenerative modes through a single VFD. Also noted is the use of touch screen local controls, handheld radio controls, starting/stopping/ braking philosophies, safety device interfaces, and the local to remote control interface.

Jan 1, 2004

By P Moser

Within the EU-research project "Blasting Control", jointly operated with partners from France, Italy and Greece, between 1992 and 1995, the Department of Mining Engineering of the Montanuniversity Leoben, Austria took over the task to develop a diagnosis system applicable in underground drifting, in order to identify possible reasons for blast failures or poor blast performance. For that purpose 120 m of 12 m2 test galleries were excavated at two different mine sites. For every blast performed the collar and bottom position of every hole drilled, the charged hole length and the drift and face profile of the round blasted were monitored. These 'geometrical" data were put directly from the measuring devices into SURPAC, the mine planning software chosen for data analysis. Based on the data computed, 3D plots comparing actual and planned data were made visible on the screen or as hard copies. Experience from the introduction of this system into a mining operation showed, that the system developed contributes to an improved understanding of the reasons for blast failures and forms the basis for an improved blast design. The soft- ware package SURPAC was also used to train the miners directly at the mine site in order to improve the quality of their work.

Jan 1, 1996

By D. W. Fuerstenau, G. S. Sudhir, P. C. Kapur

Quartz-limestone feed mixtures were ground in a laboratory-size, choke-fed, high- pressure roll mill. As compared to individually ground minerals, the harder component (quartz) in the product mixture is coarser, and the softer component (limestone) is finer. An energy split index is introduced for quantifying the disproportionate split of the mill energy between the feed constituents. This index is incorporated into a grinding kinetic model for simulation of the product size distributions of the mineral components as a function of energy input to the mill. The self-similar character of the size distributions is analyzed and an energy-size reduction relationship for the roll mill is highlighted.

Jan 1, 1992

By R. Houot, C. Leschevin, G. Gillet

In mineral processing, conventional magnetic separators are equipped with traditional magnetic circuits (magnetic iron yoke with copper coils or iron-clad solenoid) that develop magnetic fields of less than 2 T'. For minerals of low magnetic susceptibility, use of these circuits has many disadvantages. Only a separator with a superconducting magnet can contribute to solving the problems and produce a high magnetic field. This paper presents and describes a magnetic separator having a superconducting magnet with integrated closed circuit for helium liquefaction. The system generator and maintenance are simplified by extensive automation realized by a versatile program- mable autocontrol unit. A comparative study if the results on concentration and purification of different raw materials with the new and with conventional separators is described.

Jan 1, 1987

By B. K. Mishra, S. P. Mehrotra, Anand Katti

Particle-size monitoring has become routine plant prac¬tice, and on-line measurement techniques have facilitated the proper control and monitoring of particle size. In this paper, the progress on an on-line size measurement technique using a y-ray source is discussed. The tray is emitted from a nucleonic density gauge (NDG) that serves as a slurry den¬sity-measurement device. This unit is calibrated and tested to predict the slurry density. Batch experiments were conducted to study the variation in slurry density of different types of ores, namely, quartz, bauxite and hematite. This data, in turn, is used to predict the size distribution of the solid particulate material making up the slurry. To calculate this size distribu¬tion from the slurry density, the theory of incremental sedi¬mentation is used. Experimental results show that the pre¬dicted size distribution compares well with the actual size distribution, as measured by the Andreasen pipette technique. Finally, a simplified scheme is proposed to monitor on-line size distribution using the nucleonic density gauge

Jan 1, 2000

By William J. Francart, Gary J. Wirth

Fire detection capability in conveyor belt entries of coal mines has advanced considerably since the passage of the Federal Coal Mine Health and Safety Act. The advances in instrument technology and computer based monitoring have provided better fire detection than ever introduced in the industry. This paper discusses recent belt conveyor fires and detections in mines utilizing CO Monitoring Systems. Data from investigative reports is presented on belt entry fires from 1991 to the present.

Jan 1, 1993

By A Pettersson

LKAB owns and operates two of the largest underground mines in the world in Northern Sweden. In Malmberget, with a production capacity of about 30,000 t/day of iron ore, the current main 815 m haulage level is rapidly approaching the end of Its life and plans are being made for its replacement on the 1000 m level. Due to the separation of the orebodies, trucks have been chosen for transporting the ore from the orepasses to the crushers. The trucks currently in use have a capacity of 120 tons. To increase the efficiency of the loaded haul, the new main level will have a favorable slope from the drawpoint locations to the crushers. From the new level the crushed ore will be transported by conveyor to the 815 m level for hoisting to the surface. The paper discusses the planned mining and transportation system.

Jan 1, 1998

By B. J. Sauer

Misapplication of ac induction motors for mine crusher and mill applications has long been a frustration for the driven equipment supplier and the mine operator. Proper selection of ac induction motors is critical to providing efficient production. This paper focuses on the selection of ac induction motors for gyratory crusher, conecrusher and grinding mill applications. The criteria for motor selection includes: proper enclosure, driven equipment torque requirements, bearing life, temperature rise, starting requirements, ambient temperature, altitude and accessory requirements.

Jan 1, 2002

By H. Huang, J. C. Wu, C. H. Xie, Y. Q. Xue, Z. H. Zhang

Two- and three-dimensional groundwater flow models for dewatering in an opencast mine are presented. The models focus on solving special problems using numerical simulations of the opencast mine. These special problems include the drying up of the aquifer, the movement of the model boundary and the prediction of the residual head. These models are used to describe the decline of groumdwater levels in the Yuanbaoshan Opencast Coal Mine and its neighboring area during the drainage period. The simulated values agree very well with the field data. There have been several successful examples of numerical simulation for predicting the mine dewatering rate in an opencast mine. However, The hydrogeological conditions for the Yuanbaoshan Opencast Coal Mine are rather complex, and the total average flow rate is very high at 4.676 x 105 m3/d (1.65 x 107 cu ft/day). In this paper, a two-dimensional groundwater flow model in a large area is developed to solve the problems mentioned above by simulating regional drawdowns of the groundwater level during the drainage period, and a three-dimensional flow model is developed to simulate the residual head near the open-pit bench.

Jan 1, 1998

By A. D. Davis, C. J. Webb, T. V. Durkin

This project took a watershed approach in the evaluation of water-quality impacts from past mining activities and current restoration projects in the Bear Butte Creek basin, a small and well-defined drainage in a heavily mined area of the northern Black Hills. The basin contains numerous inactive and abandoned mines, as well as a heap-leach surface gold mine. Bear Butte Creek normally loses all of its discharge to sinkholes in the Madison Limestone aquifer. Thus, it can affect the water quality of this regionally important water resource. Water-quality data were analyzed, stream surveys were conducted and two abandoned-mine restoration projects were monitored to evaluate the effectiveness of the watershed approach and to identify practical remediation techniques that could be applied to other watersheds. A geographic information system (GIS) was developed to organize information on stream quality, abandoned mine locations, and other geologic and hydrologic data. The watershed approach toward assessing and reclaiming abandoned mines appears to be effective when compared to a point-source approach that might improve water quality at specific sites but not result in significant overall improvement to the watershed because of adjacent sources.

Jan 1, 2000

By B. Markovic

Performance of mineral filler particles in ceramic applications can be enhanced markedly by adsorbing polymers of optimum molecular structure and dosage. In a recent work by Chen and Somasundaran (1997), a novel scheme of controlled polymer adsorption was used to produce nanocomposites of unique core-shell designs. Towards this purpose, adsorption and desorption behavior of selected polyacrylic acids (PAA) on three minerals; alumina, titania, and silicon carbide, was examined as a function of relevant parameters. Adsorption of P AA was found to depend on polymer molecular weight, pH, as well as solids loading. Specifically, the adsorption density was found to increase with increase in polymer molecular weight for non-porous alumina while it was found to decrease in the case of porous alumina. This is attributed to the inaccessibility of the pores to the larger polymers. An unexpected finding was the change in the adsorption density of PAA with solids loadings. PAA adsorbs on silicon carbide only at low pH values when the particles have very low surface charge suggesting that the adsorption in this case is controlled by electrostatic forces. Using polyacrylic acid as bridging agent between the alumina fillers (core) and nanosize alumina or titania particles (shells), controlled layer by layer deposition of nanoparticle on the core particle surface could be obtained.

Jan 1, 1997

By James L. Vanderbeek

The Chino concentrator commenced operation in 1982 as a SAG-ball mill circuit which could process 37,500 stpd of ore. Since 1982, a series of process improvements such as the addition of two stages of SAG recycle crushing, allowed throughputs to increase to more than 48,000 stpd, at the expense of significantly coarser flotation feed sizing and reduced recovery. To compensate a third (tertiary) stage of grinding consisting of four 1250 hp Vertimills was installed which has allowed the flotation feed size and recovery to return to historical levels. The design and operational characteristics of the Tertiary Grinding Circuit are described.

Jan 1, 1998

This chapter looks at the development and use of the operating budget. This is management's plan of action in the short term, usually one year. The operating budget includes all expensed production costs (i.e., all costs reported as cost of goods sold) but does not include expenditures on capital equipment, which are usually justified using discounted cash flow techniques.

Jan 1, 1999

By Wilson I. L. Lim, Jonathan J. Campbell, Luis A. Tondo

An important issue in the use of high pressure grinding rolls when grinding ores is wear of the rolls. Due to the abrasive nature of the ores, significant wear rates have typically occurred. Attempts to address the wear problem require a better understanding of the wear mechanisms. A probable wear mechanism is the abrasion of the rolls surface due to extrusion of the compacted material as it leaves the rolls. This paper presents the results of a study on a number of ores to examine the extent of extrusion that occurs. The study involved laboratory, pilot and full-scale high pressure grinding rolls. The effect of variations in parameters such as grinding pressure, rolls speed, initial gap settings, feed topsize and moisture was investigated. The results indicate that extrusion increases with increasing grinding pressure and rolls diameter, while the use of studded or profiled rolls significantly reduces the extrusion effect compared to smooth rolls. It was also found that rolls speed and feed moisture can have significant effect on extrusion, depending on the material.

Jan 1, 1998

By Thomas P. Meloy

As the importance of particle shape in mineral processing is increasingly recognized as an major variable in predicting the behavior of both individual particles and particle systems, whether it be in dense media, froth flotation, comminution or the flow of particles, new method of shape characterization are being developed, particularly for use on image analyzers. These shape characterization methods may be broadly classified into the analytical, empirical and physical formation methods. Discussed are approaches and the strengths and weakness of each of these methods. Moreover old and new shape measuring techniques are reviewed, particularly the new image analysis methods techniques such as Fourier, Haar, Fractal, Walsh and Delta as well as a variety of other techniques such as tabling, the Cascadograph, settling and L/D ratios. Also discussed are the problems of doing shape research, current progress and the future of the field.

Jan 1, 1990

By Paul Saxton

INTRODUCTION AND SUMMARY This short paper deals with the history of the Nickel Plate Mine from 1898 to 1987, with the major focus on the time period 1984 to 1987. Operations from 1898 to 1955 are reviewed in a cursory manner with the emphasis on some interesting points in the early 20th century. A review of the major exploration work carried out in 1984 to 1987 is presented and the process of moving the project through feasibility, government permitting and construction is described. The Hedley gold camp is situated approximately 40 kilometres east-southeast of Princeton, in southern British Columbia. The area has had a long history of gold mining and between 1902 and 1955 approximately 1.5 million ounces of gold were won from several mineralized skarn orebodies. Most production came from the Nickel Plate and Hedley Mascot mines. AN EARLY TO MID 20TH CENTURY SUMMARY The Nickel Plate is one of the oldest mines in the province. The mine had operated from 1904 to 1930 and, after a period of shutdown, from 1934 to 1955. The mine was revived in 1967 for exploration and. will resume production during the first half of 1987. In the first period the Yale Mining Company and Daly Reduction Company operated for six years and Hedley Gold Mining Company for twenty-one. In the second period the mine was operated by the Kelowna Exploration Company Limited and Kelowna Mines Hedley Limited for twenty-one years. In the present period the mine has been revived by Mascot Gold Mines Limited.

Jan 1, 1987

By David M. Mchaina, Allan E. Hall, Siegfried Rohr, J. D. Botsford

Incidents associated with secondary dust ignitions in the mining of massive sulphide ore deposits are of major concern in Canadian underground metal mines. During stope or development blasting, a highly concentrated cloud of sulfide dust is created and may be ignited, resulting a secondary explosion which releases a considerable volume of sulphur dioxide and possibly other sulphur gases. The consequent pressure, heat and toxic gases can result in loss of life, significant damage to equipment and loss of production. These losses are expensive and should be prevented. Explosions of this type have occurred at the H-W mine of Westmin Resources mainly in the development headings and cut and fill stapes. This paper presents the results of a study conducted at the H-W mine to compare dust sampling methods for explosivity tests. The associated benefits and pitfalls of each sampling technique are examined. The investigative work conducted to develop and test preventive and control methods against sulphide dust ignitions is also discussed. The techniques which will minimize the risk of sulphide dust ignition in metalliferous mines are outlined. A review of current preventive and control measures practised at the H-W mine is also presented.

Jan 1, 1989