Search Documents

By G. G. O. O. Uwadiale

Starting from a crude ore assaying 45.6% Fe, a fine-grained oolitic iron ore was concentrated by the oil agglomeration technique to 90% Fe recovery and 65% Fe assay. The ore required grinding to minus 5 µm to effect adequate liberation, and the technique yielded optimum results at pH 9. The roles of pH, collector, and bridging liquid concentrations on selectivity and yield of iron minerals in the concentrates are discussed.

Jan 1, 1991

This paper reports on the behavior of mercury and its compounds during the thiosulfate leaching and recovery of gold. Thiosulfate solutions are shown to dissolve Hg0 and Hg2Cl2 to a similar extent as cyanide, but the leaching of HgS is significantly slower in thiosulfate solutions compared to cyanide. Hence, the use of thiosulfate may be an option for treating ores containing high levels of cinnabar, especially since the legislation concerning the discharge or sale of mercury is becoming more restrictive. The deportment of mercury during gold thiosulfate loading and recovery using a strongly basic anion-exchange resin was also studied. Although the mercury thiosulfate complex loads on the resin, the adsorption is weaker than for gold, with an equilibrium constant between gold and mercury of 51. Resin loaded with gold, mercury and copper was pre-eluted with thiosulfate (to remove copper) and eluted with a chloride and sulfite eluant. The majority of the mercury is eluted by the eluant and, hence, its deportment closely follows gold and the eluate would need to be treated to remove either mercury dur-ing or prior to gold electrowinning.

Jan 1, 2010

Many organisations, including those in the resources industry have Board-level endorsed principles on sustainability. A key challenge, however, is how to systematically integrate these high-level principles into the design and operation of mineral processing plants. In an effort to meet this challenge the Sustainable Operations framework, called SUSOP®, was conceived and developed through the Corporative Research Centre for Sustainable Resource Processing (CSRP) in Australia. Somewhat analogous to HAZOP (Hazard and Operability Studies) which is well entrenched in the resources industry, the key aim of SUSOP® is to produce a holistic, systematic and rigorous methodology for identifying and assessing sustainability opportunities and risks. This paper argues the need for such a sustainability framework, presents the key elements of SUSOP®, highlights how case studies enhanced its development and articulates the reasons why such a framework will have growing importance into the future.

Jan 1, 2011

By Robert Snow, Yingxue Yu, Patrick Zhang

The FIPR/SAPR process is FIPR's third approach to develop a viable alternative to the Crago "Double Float" process for phosphate flotation. SAPR stands for Single-collector, All-anionic Phosphate Recovery. The FIPR/SAPR process - offers a universal flowsheet for any anionic reagent system and flotation feed of varying sizes. For an unsized or fine flotation feed, the FIPR/SAPR process consists of the following steps: 1) high-solids conditioning with an anionic collector; 2) anionic rougher flotation, with the rougher concentrate sized at 48 (or 65) mesh and the +48 mesh recovered as a final product; and 3) cleaning flotation of the -48 mesh fraction from step 2. In a variation of step 2, the rougher concentrate from the first two cells may be collected as a final product, and the rougher concentrate from the last two cells sized at 48 or 65 mesh. The new process was tested with a blend of anionic collectors, achieving single-digit Insol at 85 + % recoveries.

Jan 1, 2002

By J. H. Bassarear, J. D. Vincent

General. Copper, the first metal used by man, today is the third in consumption after iron and aluminum. Compared to these it is relatively rare, with less than 0.01% of the earth's crust copper, 8% aluminum, and 5% iron. Nevertheless. our modern civilization is heavily dependent upon copper because of its high conductivity and resistance to corrosion, ease of working, durability, wide range of properties by virtue of its readiness to form alloys with other metals, and its attractive colors and texture that make it so desirable for many crafts and arts. These attributes explain why copper is chosen for a long list of uses, including electrical wiring, switchgear, and bus bars; piping, roofing, and siding; and manufactures of brass, bronze, and other alloys. The fact that copper ore is mined in nearly all parts of the world is significant. Its importance is shown in Table I, which gives figures on world production from 1968 to 1977. In the Free World, North and South America and Africa are preeminent. The table also shows the generally upward trend of production in this period; accurate figures for 1978 and 1979 from the same source are not yet available (1980), but it is certain that major environmental, economical, and political factors continued to disturb the industry in those years and into 1980.

Jan 1, 1985

By Ernest Peters

To model the zinc pressure leach, equations have been written that describe the rates of individual reactions taking place, including (a) oxygen mass transfer, (b) ferrous oxidation by dissolved oxygen, and (c) ferric reactions with ZnS and other minerals. In the continuous process, at steady-state, these take place at the same rate, and so the equations can be solved simultaneously. Model calculations using simultaneous equations are shown in graphical form to demonstrate the effect of different variables on the leach performance.

Jan 1, 1993

By A. D. Trujillo, R. D. Wunder

The Chino Mines Co., a Kennecott- Mitsubishi partnership, located in Hurley, NM, recently completed a $405 million modernization of its mine, concentrator, and smelter facilities. The mine/concentrator modernization commenced in 1980, and the smelter modernization began during 1982. Modernization of the mine and concentrator facilities involved increasing the mining rate from 98 kt/d (108,000 stpd) to 152.2 kt/d (167,800 stpd). Ore mining was designed to increase production from 20.2 kt/d (22,300 stpd) to 34 kt/d (37,500 stpd). A new concentrator was con- structed near the mine using semiautogenous grinding. The new smelter uses the INCO flash smelting process, increasing capacity by 40.8 kt/a (45,000 stpy) to 99.8 kt/a (110,000 stpy) of saleable copper.

Jan 1, 1988

By S. Liu

A general account of nitrogen-generating systems, including the surface fixed, surface-mobile and underground-mobile types is presented. These systems have recently been adopted in coal mines in China to prevent and extinguish fires. The paper stresses nitrogen -injection technology and relevant systems of monitoring and stopping air leakage.

Jan 1, 1998

By Z. T. Bieniawski

After many significant advances in mining, including development of sophisticated methods for strata characterization and numerical modeling analyses, the engineering design process in mining strata control is as primitive as it was two decades ago. Yet, major advances in design methodologies have occurred in other branches of engineering. Is creative design in mining a myth only? Are we deluding ourselves when we talk about innovative mining design of today? Did you know that most design experts are often unaware of their own decision-making processes? This paper explores the methodology of creative engineering design as a new recognized discipline.

Jan 1, 1987

By William H. Schiffbauer

Research is being conducted toward making underground mining equipment autonomous. This will facilitate improvements in safety by relieving workers of dangerous tasks and will increase production by providing more accurate control with less down time.. A Bureau of Mines developed microcomputer network has enhanced this research by permitting a group of diverse computers to interact with a mining machine as well as with each other over a common data link. The network is composed of specially integrated off-the-shelf hardware and industry-standard operating system and programming languages. Using the network, researchers can conduct various experiments with the mining machine using a diverse group of intelligent sensors, computers, and microcontrollers. Descriptions of the mining machine, the mining machine control computer, control algorithms, -the microcomputer network architecture, and communication protocols are discussed.

Jan 1, 1989

By Eric Monrad

Discrete event simulation modeling provides a tool to quantify the throughput capacity of stockyards. Interactions between the main equipment types (trains, dumpers, conveyors, stackers, reclaimers, shiploaders) can be captured, including route blockages, breakdowns, and planned maintenance. Simulation has been successfully used at world-class stockyard facilities to determine current capacity and to identify gains resulting from improvement projects. Recent projects have focused on iron-ore, coal, and soya facilities, but the technology is suitable to be used on any bulk material type.

Jan 1, 2008

By G. M. Rao

It has been a universal observation that rich grades of ores and minerals are getting depleted, simultaneously the demands for civilization are ever increasing coupled with occurrence of poor grades of ores and minerals posing a problem to the processing engineers. At the same time, the cost of mining and milling are increasing, creating a situation where the management has to handle and process low grade ores at an economic level keeping environmental stipulations and control to be safeguarded which has been an additional cost for the management to comply with.

Jan 1, 1994

By Robert L. Sundeen, Richard V. Wenberg

INTRODUCTION Early rock-bolting practice usually consisted of ran¬domly installing bolts, using hand-held drilling equip¬ment such as air-leg mounted sinkers or stopers. As bolting technology evolved, the practice of installing uniform bolt patterns was developed, utilizing random bolt installation as required within the uniform pattern. The uniform rock-bolting technique, when used as the principal method of rock support, requires drills and jumbos designed specifically for rock bolting. This equipment is similar to conventional face drilling machines, except that the jumbos can orient the drills to obtain any necessary bolting angle; often, this means bolts may be installed at or near perpendicular to the centerline of the drift or stope opening. Fig. I shows a typical rubber-tired rock-bolting jumbo of the type commonly used in drifts and room-and-pillar mining. Modern rock-bolting jumbos are capable of drilling the required holes, inserting rockbolts, and torquing them to proper levels. Jumbos also are available for use with resin-anchored bolts. Probably the most unusual of this type utilizes a rotating bolt turret that carries the rock drill, resin charging unit, and the bolt in a single mechanism. Once the turret is loaded with the resin and bolt, further manual effort is not re¬quired. Drilling and bolt placement are accomplished by the operator from a station remote from the bolt site. Fig. 2 shows this turret device. Roof-bolting jumbos are available mounted on rail, crawler, or rubber-tired chassis. Various types of rock drills are used. Depending upon the type of rock, these may include rotary, percussion, or rotary-percussion drills. Fig. 3 shows a typical rail-mounted jumbo. CONDITIONS INFLUENCING APPLICATION General Rock Conditions Rock-bolting generally is applicable in moderately hard to hard rock. No particular type of rock is ex-

Jan 1, 1982

By R. C. Bryan, D. B. Jamison

This paper describes a procedure for minimizing the operational costs associated with blending sodium in coal at a surface mine in the Powder River Basin. Mine site blending is performed by adjusting daily production rates for high- and low-sodium pits. These adjustments are designed to produce a consistent sodium value called the blending target. The mine's contractual limit for sodium is sufficiently close to the field average value that any decrease in the sodium blending target may result in an opportunity cost, if the number of potentially minable tons is reduced. Conversely, any increase in the blending target may result in a higher sampling cost if more information is required to keep the blend within contractual limits. Blending parameters were defined using a geostatistical block model of sodium content that was based on analyses of hundreds of in-pit sample holes. Variograms for these data were used to compute the marginal costs of opportunity and sampling for a series of hypothetical in-pit drilling patterns. These marginal costs provided a basis for selecting optimum values for key parameters such as the blending target, production variance and in-pit sampling density. The benefit of implementing these optimized parameter values is that operational costs of sodium blending will be minimized over the long-term. At the mine where this procedure was developed, each dollar spent to increase the sampling density to the optimum value was shown to generate a $10 savings in opportunity cost.

Jan 1, 1991

By C. K. Lee

The influence of passageway fires on ventilation flows was investigated in three horizontal fire tunnel s: 1. a laboratory-scale fire tunnel network, 2. a small-scale fire-plume tunnel, and 3. a large- scale simulated mine gallery. Wood was used in the first and third tunnel and gas-burners were used in the second one to generate passageway fires. Experimental measurements included gas mass flow rate, velocity, temperature and pressure in the passageways and exhaust fans. The overall and local effects of the fires were investigated by comparing these measurements obtained before and during the fires. Results show that a passageway fire essentially increases the flow resistances of the passageways of a tunnel flow network by virtue of volatile fuel mass injection and high combustion temperatures. The ventilation air flow rate is consequently throttled to lower values than that before the fire. At severe throttling, reverse flow occurs. Conditions for reverse flow are characterized by two Froude numbers based on gas velocity and density upstream of the fire, and height of the passageway. The Froude numbers and the characteristics of the passageway fire are necessary to analyze mine ventilation/fire interaction and to predict mine ventilation patterns during fires.

Jan 1, 1980

By Ralph D. Daley, Kevin E. Redinger

The production of coal/water fuel (CWF), a highly loaded mixture of finely ground coal, water, and chemical additives, presents a unique opportunity for significant ash and sulfur reduction through physical coal cleaning. Froth flotation can be integrated with the staged, wet, fine grinding inherent in the CWF production process. A laboratory scale research program was conducted to demonstrate the feasibility of a flexible, integrated coal cleaning/CWF process flowsheet. Performance of the conceptual flowsheet was examined for two coals of CWF commercial interest, Upper Freeport and Pittsburgh seam coals, from central and southwestern Pennsylvania, respectively. Several multi-stage coal flotation and reverse flotation circuits were evaluated. CWF was produced from the cleaned coal in each case at similar solids loadings and viscosities as observed for the raw coal. However, the ash loading and SO2 emission potential for each CWF had been significantly reduced.

Jan 1, 1988

By Sidney L. Hansen

This report was written because of concerns of the possible error involved when stopping leakage is incorrectly assumed to be turbulent. It is common practice to use turbulent flow to characterize each airway branch for computer models of mine ventilation circuits. This report addresses computer methods to accurately model air-leakage paths. A graphical method is described for deriving the equations of leakage through stoppings. The significance of modeling leakage according to the proper flow regime (turbulent or laminar) is demonstrated by the following method. A hypothetical mine was developed to represent present-day conditions. The stoppings of the mine were chosen to leak according to laminar flow properties. The mine was represented by constructing two base models. One base model used turbulent leakage equations for each stopping, while allowing the corresponding resistances to vary. The other base model used the correct laminar leakage equations and held corresponding resistances constant. The mine circuit was then expanded to demonstrate future development. The expanded portion was designed with stoppings that were identical to those in the base mine. The mine in the future state was represented by two projection models. Each projection model was an extended version of its associated base model; one used turbulent leakage equations and one used laminar leakage equations for stoppings. The laminar projection was theoretically correct and is used as a basis for comparison of differences in airflow quantities. Rather than modeling every leakage path for stoppings, a more practical approach is also discussed. A good level of accuracy is maintained by combining leakage paths if the proper flow equations are used. This method was used on the hypothetical mine projection and the flows were very similar to the theoretical values.

Jan 1, 1989

By W. D. Diment

The concept of flying employees in and out of remote mine sites on a regular rotation basis, rather than establishing permanent support communities nearby, has gained increasing acceptance by mine operators, unions and regulatory agencies in Canada. The development of successful fly in/fly out programs and resultant compressed work schedules is dependent on meeting design requirements through comprehensive research of worker profiles to ensure the selection of suitable employees and the implementation of satisfactory working conditions. This paper presents an overview of Canadian mine industry practice with regard to the fly in/fly out mode of operation and compressed work schedules.

Jan 1, 1987

By John C. Braithwaite

Gold production commenced in New Zealand during the gold rush of 1861, and recovery to date is over 900 tonnes, almost 60% of which was alluvial. New Zealand pioneered development of bucket line dredges during the 1880's. The advent of the modern hydraulic excavator and increased gold price led to a resurgence in alluvial production with about one hundred plants in operation in 1988. The processing plants are mainly floating, with throughputs of 50-100m3/hr fed by backhoes of 20-40 tonne operating weight. Some larger plants with more sophisticated recovery systems have commenced over the last few years, with the largest using a 180 tonne backhoe.

Jan 1, 1989

By Rick McGregor, David Blowes, Mike Choi, Ralph Ludwig

The oxidation of sulfide minerals at an ore transfer location in Western Canada has resulted in widespread contamination of underlying soil and groundwater. The oxidation of sulfide minerals has released sulfate [SO,] and heavy metals including cadmium [Cd], copper [Cu], nickel [Ni], lead [Pb], and zinc [Zn] into the groundwater. A compost-based sulfate-reducing reactive wall was installed in the path of the plume in an attempt to reduce the potential impact of the heavy metals on a down-gradient marine inlet. Monitoring of the reactive wall over a 21-month period has shown that Cu concentrations decrease from over 4000 ug/L to less than 5 ug/L. Cadmium, Ni, Pb, and Zn concentrations also show similar decreases with treated concentrations generally being observed near or below detection limits.

Jan 1, 2000