Search Documents

By D. H. Carlson, J. H. Johnson, C. F. Renders

Research was conducted at a western coal mine on a wide variety of underground mining vehicles to develop testing procedures for portable instrumentation monitoring of tailpipe concentrations of diesel particulate matter (DPM), carbon dioxide (CO2) carbon monoxide (CO) and nitric oxide (NO). DPM was measured using the Emissions Measurement Appa¬ratus (EMA) developed by Michigan Technological University (MTU), and an ECOM-KL five-gas analyzer was used to measure gaseous tailpipe concentrations. Baseline concentrations of the tailpipe pollutants were measured using vehicle systems to load the engine. Concentrations before and after the water scrubber were measured and water scrubber efficiencies were estimated by calculation. Field measurement procedures were established. Heavy-duty vehicles with automatic transmissions were loaded using the torque converter to stall the engine. Consistent engine loading for light-duty vehicles with manual transmissions involved placing the transmission in neutral and adjusting the throttle to maintain a constant engine speed of 2,500 rpm. Tailpipe CO2 concentrations for Caterpillar 3306 and 3304 engines were compared to laboratory CO2 data from Caterpillar and MSHA to help determine if engine settings were correctly adjusted for operation at high altitudes. (Perfect agreement between the mine vehicle tailpipe and laboratory measurements would not be expected because of the differences in the test conditions.) DPM concentrations for light-duty vehicles ranged from about 20 to 160 mg/m3, and one light-duty vehicle averaged near 1,000 mg/m3. DPM concentrations for heavy-duty vehicles ranged from about 55 to 200 mg/m3. Widely ranging DPM concentrations for a particular vehicle type reflect the state of maintenance, fuel rate settings and different engine loading procedures as well as differences between samples collected upstream and downstream of the waterscrubber. The calculated DPM removal efficiencies due to the water scrubber varied considerably between vehicles, ranging from 13% to 51%. Calculations indicate that, under worst-case conditions, very large reductions in DPM may be required to meet the proposed DPM PEL of 0.15 mg/m3, even on vehicles with water scrubbers. In-mine ambient air studies, which are needed to actually measure the impact of the tailpipe concentrations on the work environment and the effect of mine ventilation on the dilution of DPM were not done in this first set of tests.

Jan 1, 2000

By Ricardo D. Presnell, Erich U. Petersen, William J. Tafuri, Donald M. Hausen, Russell C. Babcock, William L. Gunter, Thomas R. Gibson, Douglas N. Halbe, Jay W. Hammitt

The Barneys Canyon orebody is a sediment-hosted disseminated gold deposit located 8 km (5 miles) north of the Bingham Canyon porphyry copper mine. Mineable oxide reserves are 8.6 million tonnes (9.5 million short tons) grading 1.64 g/tonne (0.048 oz/ton) gold. Host lithologies are carbonates and siliciclastics of the Park City and Kirkman-Diamond Creek Formations of Lower Permian age. Gold distributions are controlled by favorable stratigraphic units and associated alteration, and structures. Dominant alteration is decalcification and bleaching of carbonates, and argillization and bleaching of sandstones. Gold to silver ratios are greater than 1:1. Anomalous trace metals include arsenic, antimony, mercury and thallium. The Melco deposit lies 2.4 km (1.5 miles) southwest of the Barneys Canyon deposit. It is spatially associated with a steeply northwest-dipping siliciclastic breccia in the Kirkman-Diamond Creek Formation at the contact with underlying orthoquartzites of the Freeman Peak Formation. Both gold-bearing oxidized and sulfide lithologies are present, often in sharp contact. Mineable oxide reserves are 2.8 million tonnes (3.1 million short tons) grading 2.40 g/tonne (0.07 oz/ton) gold. Anomolous trace metals include arsenic, antimony, mercury and thallium, which are generally present in concentrations greater than those at Barneys Canyon, particularly in sulfide-bearing material. A spatial, temporal and genetic relationship is proposed between the Melco deposit and late-stage gold mineralization at Bingham Canyon, although both the Melco and Barneys Canyon deposits have many similarities to Carlin-type gold deposits.

Jan 1, 1990

By James Stewart

"THAT WHICH WE CANNOT SEE" INTRODUCTION Often it has been stated that the greatest of all fears is fear itself - fear created only by that which we cannot see or by that which we fail to understand. The elimination or minimization of fear can best be accomplished by a thorough understanding of the underlying causes of the fear. As related to the mining industry the omnipresent fear is the dread of acquiring cancer through accumulated exposure to "that which we cannot see" - radioactivity. The understanding of the resulting exposure effects can best be obtained through acquisition of authentic data and the subsequent analysis of the same by a group of highly qualified specialists. I may point out that the nuclear industry and its source, uranium mining, greatly surpass any other industries in the degree of public awareness as to its potential environmental effects. Public out-cry has always influenced major decisions relating to how industries conduct their operations and much of their effort has resulted in many changes. The issues of health and safety in the mining industry have created considerable public concern, but intense concern to those of us directly involved within the industry. Increasing concern regarding the effect of human activity on the quality of the outer environment of air, land, and water has developed within the past two decades. There is now a growing concern about the health and safety of persons at work in their inner environment, of their working-places in industry. Hearings and investigations conducted in Canada by three appointed "Royal Commissions" have all confirmed that this concern is well justified when focused on the health and safety of workers in our mines. REGULATORY CONTROL OF URANIUM MINING OPERATIONS In Canada, the ownership of mineral resources and the control of their extraction, except for uranium, is vested under the "British North America Act" in the provinces. In all provinces the statutory basis for health and safety provisions in the mining industry can be found in the provincial "Mining Acts" with each province assuming the responsibility to produce its own "Mining Act". In particular, all of the Mining Acts in Canada place upon the management of a mine the responsibility to ensure that provincial provisions are met. The "Federal Register" and mining companies parallel this arrangement in the United States. Equivalent legal

Jan 1, 1981

By J. A. Herbst

Grinding circuits employed in mineral processing operations are designed to produce feed materials for beneficiation steps such as flotation and magnetic separation, which are sufficiently fine to achieve good liberation of valuable minerals from gangue without over- grinding. In many respects, grinding is the most important unit operation in a mineral processing plant. If adequate liberation is not achieved during grinding, subsequent separation steps will yield low metallurgical recoveries and/or product grades. Grinding energy requirements and operating costs typically exceed 50% of the total expenditures of the entire plant. Because grinding is an inherently energy intensive process and grinding circuit capital and operating costs are high, it is essential that such circuits be run as efficiently as possible. In- creased efficiency in grinding usually translates to a decrease in the energy required to produce a metric ton (short ton) of product size material. It is generally accepted in the mineral industry that efficient grinding circuit performance can not be achieved without the use of some form of automatic control. This is true because all circuits are subject to random disturbances which, if left unchecked, will upset circuit performance and rob a plant of productivity. Such disturbances arise from a variety of sources including natural variations in ore characteristics (particularly hardness changes), uncontrolled water additions, feed-rate upsets, changes in crusher performance, and mechanical upsets such as blockages in pumps and classifiers. Many of these disturbances occur with a frequency which is too high for an operator to detect and react to efficiently. Disturbances which occur on a time scale of several minutes up to several hours can be effectively dealt with using automatic control.

Jan 1, 1979

By I. F. Walder

Mill tailings from skarn-type base metal deposits were studied in order to ascertain potential element mobility in response to weathering. Hypogene ore minerals are sphalerite, galena, and chalcopyrite, showing minor supergene oxidation to smithsonite, cerussite, and covellite. Gangue minerals are pyrite, pyrrhotite, magnetite, hematite, andradite and grossular gamet, hedenbergite, calcite, ankerite, and quartz. Foremost of the eleven tailing piles studied, the hypogene sulfide minerals show no or only incipient post-mining oxidation. Iron oxides and hydroxides form the main oxidation products in the tailings and are enriched in heavy metals. A distinction between pre-and post-mining oxide phases may be obtained based on petrographic observations which distinguish whole-grain versus partial grain replacement. Zn and Cd do not appear to be enriched in the weathering derived oxidation minerals and will be more easily leached from the tailings than other metals.

Jan 1, 1994

By J. R. Patts, L. D. Patts, S. J. Janisko, T. Barone

"Controlling float coal dust in underground coal mines before dispersal into the general airstream can reduce the risk of mine explosions while potentially achieving a more efficient and effective use of rock dust. A prototype, flooded-bed scrubber was evaluated for float coal dust control in the return of a continuous miner section. The scrubber was installed in line between the ventilation tubing and an exhausting auxiliary fan. Airborne and deposited dust mass measurements were collected over a period of three days at set distances from the fan exhaust to assess the changes in float coal dust levels in the return due to the operation of the scrubber. Mass-based measurements were collected on a per-cut basis and were normalized per foot of advance by the continuous miner. Results show that average float coal dust levels measured under baseline conditions were reduced by over 91% when operating the scrubber. INTRODUCTION In 2012, underground mining in the United States produced over 342 million tons of coal [EIA 2013]. During the cutting, crushing, and transport of this coal, dust is generated and can be entrained in the air ventilating the mine. Title 30 Code of Federal Regulations Part 75.400-1 (30 CFR§ 75.400-1) defines float coal dust as particles of coal that can pass a No. 200 sieve. These coal particles can be carried by the ventilating air into return entries before settling onto mine surfaces [NIOSH 2006]. If this float coal dust becomes re-entrained into the airstream, it can propagate an explosion throughout mine workings [Harris et al. 2010]. Application of rock dust in underground coal mines is required by Federal regulation as a means of preventing the propagation of explosions by float coal dust. In order to meet Title 30 Code of Federal Regulations Part 75.403 (30 CFR § 75.403), 80% incombustible content must be maintained in the composition of dust deposited in mine entries [76 Fed. Reg. 35968 (2011)]. This fraction of incombustible content is increased if elevated levels of methane are present. In order to maintain the required incombustible content, frequent or constant application of rock dust is undertaken by mine operators. Title 30 Code of Federal Regulations Part 75.2 (30 CFR § 75.2) defines the properties of the rock dust that must be used by mine operators."

Jan 1, 2015

By B. A. Hancock

It is not at all surprising that causticized potato and potato derived amylopectin starch solutions performed much better than their parent starches. Some preparation is required to rupture the starch granules to effect the polymeric adsorption and interparticle bridging necessary for selective flocculation. In laboratory work comparing the deslime performance of causticized and autoclave cooked laboratory corn starch solution preparations, it was found that higher deslime weight rejections, with attendant proportionally greater iron unit losses, occurred with the causticized starch. These results may be specific to the ore involved but they do suggest that cooking and causticizing cause different starch granule rup- ture and/or starch breakdown, which have an effect on desliming response. I calculated from the data in the article that the slimes product grades were high - 24.3% and 20.3% Fe when 53.7% and 54.5% Fe concentrate products were obtained, respectively, in Table 4, and 21% Fe with a 62.6% Fe concentrate in Table 5 - using the natural tailings sample, which had a head of 34.3% Fe. It may be advisable for the authors to consider different starch preparations in future investigations. The combination of upgrading and selectivity results presented in Table 4 are not as good as the authors suggest. The authors' claim that a system has been developed to produce saleable concentrates from the Kudremukh tailings is quite disconcerting. There are many hurdles yet to be crossed before commercial application of selective flocculation becomes possible because differ- ences between the very small-scale laboratory tests conducted and commercial application are rather large. Among the many differences are varying circuit feed grades that will occur from use of tailings, the apparent face that much lower tailings grades will be encountered in practice (it is much easier to achieve a high concentrate grade with reasonable recoveries using 34.3% Fe tailings as in the study rather than 25.3% Fe tailings grades that the plant apparently averages), the hydraulic nature of the thickeners used in operations compared to the static system used in laboratory tests, the different size distributions that will be obtained from a plant closed grinding- classification circuit, and differences in water used in a plant operation and the laboratory. The authors wrote that it was necessary to overgrind to be sure that the coarse gangue would not settle with the iron oxide floccules. This situation is likely to be exaggerated in commercial operations where it is assumed cyclones would be used for classification. Because cyclone classification is greatly influenced by particle densities, there will probably be an even greater difference in size between the iron and gangue particles in the plant, which would make the gangue slightly coarser still in relation to the iron. This would make the selective flocculation-desliming separations using the procedure employed by the authors even more difficult and, using the dispersant system the authors employed, greater overgrinding would be required. To grind finer to minimize the coarse gangue in the flocculated iron oxides is quite inefficient and appears not to broach the problem. The actual problem appears to be insufficient dispersion of the ground pulp. In this situation, addition of a dispersant would likely be required to attain a sufficiently high pulp dispersion level to efficiently effect a selective flocculation-desliming separation. Although the very coarse particles would still have a tendency to settle with the floccules, it probably would be found unnecessary to overgrind as much as indicated. Use of an optimum combination of dispersant and pH modifying reagents may also significantly improve the selectivity of desliming. Additionally, although it is possible that sufficient dispersion may be obtained by pH control alone in some situations, it is quite probable that added dispersity was obtained in the reported work from using distilled water. It is research experience that distilled water enhances dispersion. In commercial operations it may not be expected that sufficient dispersion will be obtained by pH control alone, unless the water used in the process is by nature quite dispersive. Overall, a change in the Kudremukh tailings dispersant scheme appears necessary where a dispersant is used in conjunction with a pH modifying reagent. With this change, different dispersion-flocculation responses will result that would have to be further evaluated. Therefore, it is still an open question whether an efficient and effective selective floccula- tion separation using Kudremukh tailings may be obtained that will produce saleable concentrates.

Jan 1, 1987

Crushing and grinding The Crushing and Grinding Technical Committee There was substantial activity in the area of crushing and grinding with the improved outlook in the industry. The Crushing and Grinding Committee's theme of 1987's Annual Meeting in Denver was Fundamentals of Mechanical Design for Crushing and Grinding Mills. At the meeting, the concept of gearless sag mill variable speed drives was taken out of the closet, dusted off, and a wraparound motor was put on hard copy with the ordering of a 9.7- x 4.5-m, 8.2-MW (32- x 15-ft, 11,000-) sag mill. Additionally, comparisons were provided to the mill design of the gearless drive sag mill and the twin 4.5 MW (6000 hp) do variable speed drives placed on the drawing board for the Kennecott UCD Expansions. This involved a 10- x 4.5m, 8.9 MW (34- x 15 ft, 12,000 hp) sag mill. Differing opinions were also expressed in technical presentations pertaining to the need for quality mill specifications in design and manufacturing. J. Berney-Ficklin of Bechtel presented a paper outlining the need for quality design and manufacturing specifications in large scale grinding mills, and the overall cost reduction in capital and operating costs. Others presented differing specific views, but all emphasized a central theme. Quality and reliable designs in large mills should not be compromised. In-pit crushing applications continue to increase, overseas and in the US, in both mining and quarrying. Different in-pit crushing units have been classified as mobile, with integral transport systems; semi-mobile, typically modular systems that use separate transporters for repositioning; semi-stationary plants that must be dismantled before transporting and typically require earthwork and concrete foundation work; and stationary in-pit crushing plants, which remain in place for the life of the pit. The majority of equipment sales of conventional crushing and grinding circuits in 1987 were to gold mining operations. There have been two areas of end use: • conventional jaw/gyratory or impact crushing circuits preparing low grade ores for heap leaching; and • small scale sag/ball mill circuits preparing higher grade ores for classical cyanide leach/ recovery circuits. There was also continued interest in ABC and SABC circuits for both base and precious metals plants. High pressure roll crushers continue to attract considerable interest in the cement industry. There, they are used to prepare raw materials or clinker for subsequent ball/tube milling. However, they have apparently been less successful in the mineral industry where the energy savings/ capacity gains have been much less dramatic. Several papers covering the theory and application of these machines were presented in an industrial minerals session on cement at the SME Annual Meeting. The Third International Conference on Hydrocylones, held in England in October produced several papers of interest on classification and screening to the mining industry. In particular, a new cyclone apex, developed by Mt. Newman Mining, shows promise of reducing water flow to the cyclone underflow stream and, therefore, increased underflow pulp densities and reduced fines recycle in grinding circuits. A twin vortex hydrocyclone was also described and shown to give a sharper split than conventional units. Similar double cyclones were introduced in the 1950's, but failed to achieve widespread acceptance. This was due mainly to a proneness to blockage in the transitional zone. It will be interesting to see whether this latest variant can overcome this problem in the typical operation. A number of North American iron ore plants installed the capability to produce fluxed iron ore pellets. Most chose to grind the stone on site with circuits designed to grind taconite ore. Methods employed to grind this material included single-stage ball mills closed with fine screens, rod and ball mill circuits - both open and closed with cyclones - and semiautogenous mills, followed by ball mills closed with screens or cyclones. Dewatering and tailings disposal B.M. Moudgil and D.L. Sober, University of Florida Due to tightened environmental regulations and the need for more efficient land use, a greater interest in dewatering and waste disposal has developed. As a result, research efforts in flocculation, surface chemistry, and polymers science have focused on the problems related to the dewatering of solid mineral wastes. A few studies have been conducted to examine the flocculation process. Hogg et al., (1987) discussed the formation and growth of flocs. They determined the size and density of flocs was controlled by the physical conditions of the system (e.g. agitation,

Jan 5, 1988

By Paul F. Saxton

Introduction As the world economies continue to face an increased demand for natural resources to support growth in the established and developing world, the western mining industry has expanded its operations and funding of mineral developments into new and relatively unexplored regions of the world. Mining companies worldwide, in order to grow in a global economy, are now actively exploring and developing mineral resources in the emerging markets of South and Central America and most recently have expanded activities throughout Asia. South East Asia Resources (S.E.A. Resources) has recognized the vast resource potential offered by countries such as China, India and Indonesia, Asia's main driving forces of economic growth and has made a commitment to be actively involved in the area. These countries rich in mineral resources, represent some of the highly prospective and underexplored regions on earth. Their vast potential has been underestimated because of political reasons and overlooked as Central and South America still continue to be the focus of exploration for many mining companies. Most of these Asian countries have faced a prolonged period of political unrest and it has not been until recently that they have begun to enjoy a relatively stable political climate which has encouraged foreign investment, growth and economic development. These countries are in need of capital to develop their infrastructure and market economies. Their wealth in resources is one of the best methods to achieve their goals. Gold is usually one of the first targets to be extracted from developing economies. Equivalent-sized gold projects tend to cost less to develop and require less supporting infrastructure than base metals. These projects are easier to finance and, most important of all, tend to give a quicker return on investment than that offered by base metals. They also provide the economy with precious foreign exchange, international investment and the technology required to build the country. Following is a graph representing the global re-allocation of the total capital investment on the twenty largest gold projects now under construction with the total for those under construction in 1990.

Jan 1, 1996

By James G. Tilton

Subsidence resulting from mining operations, has been the object of sporadic study for many years. Reports have shown that subsidence has ranged from minor settlement detected only by precise measurements to great slips where buildings are destroyed, roads disrupted, and large fissures opened at the surface. For years, a controversy has raged over the question of whether there is a positive or negative angle-of-draw. None of these questions can be given a flat answer for the variables controlling, subsidence are infinite. Generalizations can be made for various situations and areas but some means of control must be executed.

Jan 1, 1966

By N. D. Jagger, I. M. Arbuthnot

Introduction Over the last five years, a large number of small- to medium-sized carbon-in-pulp treatment plants have been built in Australia, most designed to treat between 250,000 t/a and 1.5 Mt/a of ore. Because of the limited capital resources and tight cash-flow positions of these relatively small mining companies, the primary requirement was often to get a plant built and operating in a short period of time and at minimal capital cost. Therefore, since the inclusion of both pre-leach and tailings thickeners represents an obvious and significant capital cost, most of these plants were built without thickeners or even detailed, cost-benefit analyses on their inclusion. In some cases, the increasing use of High Rate Thickeners (HRTs) in the mineral processing industries has, however, resulted in a reassessment, because of their considerably lower cost. This reassessment was triggered primarily by the need to conserve water in arid mining areas where borefields are costly to install and water is limited. With the startup and operation of these installations, the resulting significant savings in cyanide consumption has been recognized, in many situations, as a primary justification for the installation of HRTs. Solution balances Degradation of cyanide occurs in the tailings water discharge to slime dams. The degree of degradation (cyanide loss) in the water recovered depends on a number of factors, but it is usually assumed to be about 90%. The most important mechanisms of CN loss are through HCN losses and oxidation by oxygen in the air, which also assists in the hydrolysis of CN. These mechanisms are supported by the large dam surface area and the long retention time of the tailings water in the dam. By thickening the CIP tailings at the plant and recovering as much tailings water as immediately possible, these losses are avoided. The retention time in an HRT is less than three hours, and the surface area is relatively small. Therefore, CN losses are negligible, which is not necessarily the case in conventionally-sized thickeners. Fig. I shows a block diagram of a 100-t/h gold plant without a thickener. In this example, 50% of the tailings water pumped to the tailings dam is recovered, and the CN concentration of the returned water is 10% of the tailings CN concentration of 150 ppm. Fig. 2 represents a plant with an HRT on tailings, thickening to 55% w/w solids. In this case, the thickened tailings are pumped to the dam, and 25% of the contained water is recovered. The recovered water and the mill make-up water are not sent directly to the mill; instead, they are added to the thickener feed and mixed with it prior to thickening. By doing this, the tailings are effectively washed, and the additional cyanide is recovered. Solution balances over these two circuits show cyanide recoveries of 5% and 65%, respectively. Thus, the thickener use increases cyanide recovery by 60%. Fig. 3 shows a two-stage HRT circuit in a countercurrent decantation (CCD) configuration. In this example, an additional 13% of cyanide is recovered through the use of the second-stage unit. This configuration can be justified when residual cyanide levels are high. Capital and operating costs - Case study 1 Illustrative cost figures are based on a CIP tailings thickener installed, in early 1988, as part of Dominion Mining's treatment plant at Paddy's Flat near Meekatharra. (All costs within this paper, unless stated otherwise, are in Australian dollars.) [Assumptions: Feed rate 150 t/h Ore moisture content 5% Leach density 40% solids Underflow density 55% solids Residual cyanide in tailings 150 g/m3 Flocculant dosage 15 g/t Consumable costs: Water $ 0.40/m3 Cyanide$ 2.00/kg Flocculant$ 4.50/kg Power$ 0.12/kWh Length of tailings pipeline2,500 m Capital costs of the major items involved in the thickener installation are given below: Thickener unit, 15-m diam $ 230,000 Water return pumps 12,000 Water recirculation pumps 28,000 Feed box 5,000 Flocculant make-up system 18,000 Flocculant storage tank and dosing pumps 11,000 Piping and valves 85,000 Electrics and instruments 47,000 Civil works 29,000 Installation 69,000 Total cost$ 534,000] Savings in capital costs that can be attributed to the

Jan 1, 1993

By T. A. Gray

There are several potential large-volume uses for coal ash in mining-related applications that could be environmentally and economically beneficial to mining companies. Actual usage, however, may be constrained by regulations or by perceptions of coal ash and the potential uses. To identify currently allowed uses and to assess constraints to coal ash use in the eastern coal fields, questionnaires were sent to state coal mining agencies to determine their policies on coal ash utilization and to mining companies to solicit their viewpoints on coal ash utilization. Identifying and understanding the constraints will allow for the development of a coordinated and consistent approach to remove or reduce these constraints and possibly allow for increased utilization of coal ash by the mining industry. This paper summarizes the findings of our investigation.

Jan 1, 1995

By Simon D. Strauss

This paper discusses the ways in which the metals industries dealt with surplus capacity in the past, primarily the twenty years, 1950 - 1970. During this period, the bulk of metals production in the market-economy countries was controlled by private sector companies. Since then, public sector companies have played an increasingly important role in the metals industries of the market-economy countries. Of course, the change was not overnight. It occurred gradually over a period of many years. Indeed, by 1965, several developing nations had adopted policies of government control of metal operations previously in private hands. The metals industries are so many, so large and so diverse that the constraints of time make it impossible to deal with all segments. To illustrate the problems of surplus capacity in the metals industries during the period, this paper focusses primarily on three metals. One experienced rapid market expansion between 1950 and 1970; one had a growth more or less in line with the expansion of the world economy; and one lagged well behind the pace of industrial expansion. No one will be surprised if aluminum is identified as the metal with rapid growth; copper is identified as the metal that kept pace with the world economy; and tin is identified as the laggard. Individual computations of the rate of growth for these metals show some variations, but most estimates place the increase in aluminum consumption in the market economy countries between 1950 and 1970 at a compound annual rate of about 8%. The corresponding figure for copper is a compound rate of 4%. Tin consumption showed no growth. A widely accepted point of view is that sharply rising demand will force the price of a commodity to increase substantially in order to attract a necessary expansion of supply. The corollary to this is that stagnant demand will hold prices down, as there is no need to stimulate new supply and it may be necessary to force marginal producers out of the market. The experience with aluminum, copper and tin in the years 1950-1970 does not support this theory. In 1950, the average prices in the United States market as reported by the American Bureau of Metal Statistics were 17.74 a pound for aluminum, 21.24 a pound for copper, and 95.54 a pound for tin. The corresponding figures in 1970 were 28.74 a pound for aluminum, 57.74 a pound for copper and 174.24 a pound for tin. Aluminum, with the greatest market growth, rose by 60%, whereas tin rose 82% and copper by 172%. Clearly, other factors were a more important influence on price than was the trend of demand To revert now to the capacity issue, during the period under review aluminum demand was rising so sharply that that industry had no sustained problem with surplus capacity. Instead, if anything, capacity may at times have been a constraint on demand. The industry succeeded in attaining explosive market growth through imaginative research and promotion programs. Some of this growth was the result of substitution of aluminum for other commodities – steel, copper, wood and glass as examples. But much of the growth was the consequence of developing entirely new products through technological innovation. Prior to World War 11, the number of aluminum producers was extremely limited. Alcoa and Alcan in North American and Pechiney and Alusuisse in Europe were the dominant firms. The developing countries had virtually no production and in Japan and Germany production was only a small fraction of the North American output. During the War years the United States had financed the construction of many new facilities. After the war these plants were sold by the government to Reynolds and Kaiser in order to foster more competition in the market. Subsequently many other concerns became aluminum producers, both in the United States and elsewhere and competition for markets intensified.

Jan 1, 1989

By C. E. Jordan

The Bureau of Mines conducted research to measure the improvement provided by fine bubbles on the flotation of fine-sized particles (minus 20-um size) in an effort to improve flotation efficiency in our domestic minerals industry. The turbulent velocity distributions of the fluid within the flotation cell were measured as a function of time and position and used to increase the precision of a fine particle, turbulent flotation model. For the mineral system investigated, improved flotation response was obtained under laboratory conditions by using small bubbles and intense agitation. These results matched the model's predicted response.

Jan 1, 1989

By John A. L. Campbell

Are safety concerns justified regarding the potential for a gas explosion due to recirculation when a scrubber is used on a continuous miner? The role of a respirable dust scrubber on a continuous miner section using blowing face ventilation is examined in this paper and the above question answered. Methane control using high efficiency scrubbers coupled with blowing face ventilation is promoted.

Jan 1, 1987

By N. M. Cheimanoff

GEOCAD is an ambitious research program aimed at the development of a computer based system assisting the geologist and the production or planning engineer. BONANZA, its mining part, is a computer production scheduling tool (short to medium term) of particular relevance to complex orebodies. The principle is to simultaneously use a powerful information management system (CAD potentialities) and small expert modules integrating the exploitation context and the engineer's knowledge (Artificial Intelligence tecniques). As an illustration, a module of mineable block determination for underground exploitation is discussed.

Jan 1, 1989

By S. Makni, C. Bazin, D. Hodouin

This paper reviews approaches for the real-time estimation of mass flow rates and assays using data from on-stream analyzers and flowmeters in a flotation circuit. Results obtained using one algorithm operating on-line with an industrial flotation circuit are presented.

Jan 1, 1998

By Roland C. Walker

Traditional headed rebar has existed in the mining industry as a ground support product for many years. The head of a rebar bolt is most commonly produced by hot upset die forging. Upset die forging produces a rugged, simple head that performs well. Certain elements of the head must comply with regulatory standards, such as ASTM F432-95, which offers a standard test procedure to ensure quality of the product. The head style produced by all major manufacturers has been optimized to reduce manufacturing costs, provide greater miner safety and provide an excellent performing product. Observations were made in some mines of heads failing under in-situ loading. These observations could not be replicated according to the ASTM testing method. This paper highlights the problem and how a solution was developed. The development includes pictures of in-situ failures from the underground operations, laboratory replication tests indicating how this loading occurs, and then the use of this calibrated test method to validate the new design created.

Jan 1, 2009

By Malcolm J. McPherson

This paper describes the algorithm used in a BASIC program for an IBMXT microcomputer, to simulate the underground mine climate. The program called CLIMSIM has been developed and refined over several years as a result of considerable use at operating mines. The program has been designed to be easy to use and be understood by the practicing mine ventilation engineer. It provides predictions of the work place climate, so that the optimum ventilation/cooling system can be designed to obtain a certain air cooling power or effective temperature at the work place. An example is given of the application of the program to a mechanized cut and fill stope at the Homestake gold mine in South Dakota.

Jan 1, 1986

By Gurses Oner

In situ leaching is a relatively old mineral extraction method; however, historically only a small portion of copper has been produced from small scale operations. Recently, in situ leaching technology because of its intrinsic advantages over conventional mining and milling is being considered as a viable option for recovering copper from both low grade oxide and sulfide deposits. This paper presents the application of computers to investigate in situ technology using large whole core leaching experiments. Computers were applied to three different areas: (1) experimental control and data acquisition, (2) non-destructive evaluation of samples using x-ray computed tomography and image processing and (3) mathematical modelling and data analysis.

Jan 1, 1992