Search Documents

By D. R. Lowe

Silicic volcanic ash and its alteration product, bentonite (montmorillonite and cristobalite), occur widely within sedimentary phosphate deposits. The genetic link, if any, between volcanism and phosphate deposition has yet to be satisfactorily established The phosphatic member of the Santa Margarita Formation (upper Miocene) in northwestern Ventura County, California, consists of approximately 15 per cent volcanic ash and bentonite. Ash and bentonite units greater than one foot thick can be subdivided into a lower zone of airfall origin and an upper zone of mixed ash and terrigenous detritus washed in from surrounding land areas. This upper zone also contains up to 20 percent phosphate pellets. These thick volcaniclastic units are typically overlain sharply by thin beds (less than 6 inches thick) of relatively pure, silica-cemented pelletal phosphorite. The shelf basin in which the phosphatic sediments accumulated was characterized by quiet, reducing but not euxenic bottom waters; Abundant decaying organic debris, mainly diatoms, served as a reservoir of readily available phosphate. The sudden influx of a large volume of silicic volcanic ash into this basin and its subsequent alteration to montmorillonite had two profound effects on thechemistry of the interstitial and bottom waters: (1) during alteration magnesium was removed from these waters and incorporated into the montmorillonite lattice, and (2) the pH of these waters increased as alteration progressed Both of these effects led to the crystallization in the bottom waters of carbonate fluorapatite. This accumulated as thin phosphorite beds immediately above the volcaniclastic units.

Jan 1, 1972

By Richard B. Berg

Until its closure in 1999, the Antler was North America's only active chlorite mine. The mine is located 25 miles (40 km) southeast of Butte in the Silver Star district - an old Montana gold mining district. In 1975, two prospectors searching for talc re-examined a prospect showing a green, fine-grained mineral resembling talc. Following identification and testing of this magnesian chlorite (variety clinochlore), Cyprus Industrial Minerals began processing ore from this deposit in 1976. Chlorite veins ranging up to 30 feet (9 m) in thickness were formed by essentially complete replacement of Precambrian (Archean?) quartzofeldspathic gneiss. Chlorite replacement was controlled by near- vertical faults. These chlorite veins, typically surrounded by envelopes of sericitic alteration, were formed by the introduction of magnesium-rich hydrothermal fluids, probably related to the Proterozoic talc-forming event in southwestern Montana. Luzenac America, Inc. acquired Cyprus' talc operations in 1992, and continued to mine this deposit until the ore body was mined out in March 1999, and the mine was reclaimed. Total sorted ore production from this deposit is about 250,000 short tons (st) (227,000 metric tons [mt]). Chlorite from this deposit was primarily used in ceramic and paint applications.

Jan 1, 2001

By W. M. Aubrey

Cobbing, as used in this; paper, refers to coarse dry magnetics separation. It is applicable when, by its practice, plant cost can be reduced or the value of its products increased by the removal of a barren or lean reject or a high grade final product. This paper attempts to describe cobbing as it is now being practiced, and also the problems that are of concern to the operator and design engineer. In preparation, 16 plants were contacted, all of which were very cooperative with their time and data.

Jan 1, 1958

By J. Siege1, R. S. Popielak

A computer model was used to simulate the effect of leakage through confining beds on a hypothetical in situ leach operation in an aquifer with a thin mineralized section. The simulations were used to assess economic and potential environmental implications of leakage on an in situ leach operation. Four scenarios were modeled - three representing cases with different degrees of confinement, and the fourth representing a stratified ore zone under a low degree of confinement. The model simulated the travel path and travel time of lixiviant given the hydraulic conditions prescribed in each scenario. The results show that the travel path and travel times vary by about 10% for confinement ranging from nearly impermeable (essentially no leakage) to an extremely low level (thin confinement with a permeability about equal to that of the aquifer) for isotropic aquifer conditions. The aquifer thickness contacted by the lixiviant varied from 85% to 90%. Horizontally, 55% to 60% of the aquifer was contacted. The flow paths in the stratified aquifer were reduced in the vertical direction and expanded horizontally. Forty- five percent of the aquifer thickness was contacted vertically with 88% contacted horizontally. Break- through time for lixiviant traveling at mid-depth of the aquifer increased two times when the leakage was increased from nearly zero to a value representative of thin and highly permeable confinement. Leakage affects the economics of in situ mining by (1) increasing the time required to leach out the ore, and (2) increasing the thickness of the ore zone aquifer to be restored. The potential for environmental impacts appears to be minor. In all four simulations, the lixiviant did not contact the confining strata. Restoration would be limited to cleanup of the ore zone aquifer within the thickness contacted by lixiviant and within the radius of the lixiviant that traveled farthest away from the production cell.

Jan 1, 1988

By Y. F. Vasyuchkov

In general a term "unconventional mining or "non-traditional mining technology" getting more and more familiar to the mining engineering media. There are several alternating terminological combinations such as "in situ mining", "borehole mining", "shaftless mining", "mineless mining", "geotechnology" etc.; specific terms denote particular method of unconventional mining technology: "underground coal gasification in situ", "underground coal combustion in situ", "borehole hydraulic coal mining" and others. Principal scheme of unconventional coal mining technology is shown in Figure I:

Jan 1, 1997

By G. A. Doyle

The White Pine Mine is the second-largest active underground copper mine in the United States, covering an area of approximately 13 square miles in the Upper Peninsula of Michigan. The mine operator intends to initiate in-stope solution mining by circulating a solution of mine water, sulfuric acid, and ferric iron through rubblized ore and recovering copper from solution. As planned, the solution would be retired in the mined-out stopes following completion of solution mining activities. Investigations into the fate of the retired solution mining fluid indicate that the solution, through time, will change from an acidic, metal-rich solution to a near-neutral, reducing solution containing much lower concentrations of metals. Investigations include reaction path modeling (EQ3/6) and laboratory and in-mine experiments. The combination of neutralization and reduction will result in precipitation of most metals, primarily as metallic sulfates, chlorides, and sulfides.

Jan 1, 1996

By Tom Bruington

This paper discusses the accuracy of determining the quantities of gold and silver on activated carbon in various stages of process for typical precious metals flowsheets. Accurate plant performance evaluation depends upon reliable estimates of carbon and precious metals inventories. The sources of sampling error are identified and methods of reducing them discussed. Several case studies illustrating the sensitivity of flowsheet performance to sampling error are presented.

Jan 1, 1991

By V. F. Swanson

A mathematical model for free and hindered settling of minerals was developed. This paper describes how to apply the model in designing systems, such as fluidized bed, elutriation, mixing pumping systems, involving solids and fluids.

Jan 1, 2000

By Scott Horton

In no Confederation of Independent States (CIS) country does the mining sector play quite so commanding a role as in the mountainous Central Asian republic of Kyrgyzstan. Its president, Askar Akayev, says he would like to develop his country into "a Central Asian Switzerland." However, in Switzerland, the gold is largely under the street along Zurich's renowned Bahnhofstrasse. In Kyrgyzstan, though, the gold is still in the mountains. Accordingly, Kyrgyzstan's recent adoption of a comprehensive new mining law has attracted widespread attention. Akayev recently completed a tour of the United States. His visit drew large crowds from the business community at events staged in New York and Washington, DC. The success can be attributed as much to the attractiveness of Kyrgyzstan's min¬ing sector as to the personal charms of the nation's president. Led by a half-billion-dollar investment by Canada's uranium giant Cameco, the mining sector is leading Kyrgyzstan's economic revival. And Bishkek is beginning to show some of the same signs of a "boom town" that already mark its Kazak neighbor, Almaty. Mercedes and BMWs already outnumber the Volgas on Bishkek's major traffic arteries. After nearly two years of debates involving government advisors and a final round of deliberation in Parliament, Kyrgyzstan finally adopted its second mining law. This followed quickly in the wake of measures enacted in neighboring Kazakstan and proposed in Russia. Kyrgyzstan's new law replaces the 1992 law "On Mineral Resources." It was one of the first enactments of an independent Kyrgyzstan. The 1992 law made a major contribution to the introduction of free-market economics in the country by ending the state monopoly over mineral exploration and development. It also laid the groundwork for an independent mining industry. According to Kyrgyz government reports, Kyrgyzstan has about 270 commercially viable deposits of almost 40 types of mineral resources. These include oil, gas, coal, precious-, nonferrous-, ferrous-, rare- and basemetals. However, the nation's key draw is gold. Since enactment of the first law, the government has issued more than 100 licenses for geological prospecting for and development of established deposits of gold.

Jan 1, 1998

By Roger G. Haga, Richard P. Campbell

Introduction Project scheduling . . . . • What is it? • Why is it done? • Who does it? • How is it done? • When is it done? These are some of the questions that will be addressed in this paper. It is intended that by exploring these questions, an understanding of project scheduling, its purpose and benefits can be achieved. The purpose of this article is not to describe in detail "how to schedule", but rather to give an overview of the scheduling function on a project. A successful scheduling effort is dependent upon the people responsible for developing, implementing, and monitoring the schedule, and the tools and procedures that are used. These three elements are integral components of project scheduling. What is it? A schedule is the integration of network relationships, resource constraints and the calendar. The schedule identifies when the activities "will" be done, while the network states when they "must" be done. Networking techniques are the most widely accepted scheduling tool for complex projects. The benefit of the network is the simplicity in illustrating, presenting and analyzing the dependency relationships of a project. The logic network is the foundation of the schedule. When calendar dates are applied to the logic network, it becomes a schedule which provides the basis for evaluation of project status, forecasting the occurrence of events and controlling the project. The sequence of activities that requires the longest time to complete determines the overall duration of the schedule. This longest sequence of activities is called the "critical path". The "critical path method" (CPM) is used to describe this particular schedule network methodology. The two common conventions of CPM networks are the "arrow diagram met hod" (ADM) and the "precedence diagram method" (PIM). There are arguments in favor of each of these two methods, and usually the one that is used is a matter of personal preference, project directive or corporate procedure.

Jan 1, 1986

By Donald L. Meredith, Jeffrey Harris, Donald A. Stanley

Principal Components Analysis (PCA) is a versatile, multivariate statistical method that the Bureau of Mines is applying to mineral processing data to achieve data simplification and pattern recognition. The principal components are obtained from an eigenanalysis of the data matrix. To achieve data simplification PCA replaces a larger number of measured variables with a smaller set of principal components and at the same time removes a significant amount of experimental error. Data simplification and error reduction make PCA useful in process control. Plots of the individual principal components form the basis of a pattern recognition technique that allows detection of significant variations in the structure of the data. These applications of PCA are illustrated with appropriate mineral processing data.

Jan 1, 1993

By Paul D. Chamberlin

The evolution of heap and dump leaching has followed the development of agglomeration, materials of construction for leach pads and ponds, solution distribution systems, testing techniques, and state regulations. They are now mature processes. Possible future directions and developments are discussed. In situ leaching of precious metals is waiting to be commercialized. Regulators are reluctant to allow the use of cyanide because of the potential for excursions and operators are reluctant because of the potential for lawsuits. Developments in alternative lixiviants are needed before in situ leaching is accepted.

Jan 1, 1989

By S. W. Clark, R. Meglen

A seismic refraction survey of selected environs of Brewster Phosphate's Lonesome mine near Bradley, FL identified various layers of overburden, minable matrix (ore body) and basement (i.e., bedrock) that correlated with core logs. Bivariate correlation procedures determined that statistical relations existed between mining parameters and seismic velocities. For instance, a correlation of approximately -0.6 was inferred between P wave velocity and ore grade.

Jan 1, 1990

By Zhen-lu Zhao

The manipulators possibly used in underground mining must deal with unpredictable obstacle while keeping certain positions and orientations of end effector, and in some cases, are required to possess redundant joints in order to be more flexible. This kind of manipulators might be fitted with jumbo drill or platform as auxiliary to potentially deal with some utility works in versatile way, such as installing rock bolts, guniting, blasting, charging, surveys and measuring work, etc.. This paper describes numerical procedures of performing inverse kinematic problems for redundant manipulators .The procedures, based on the generalized pseudoinverse of Jacobian matrix, are developed to lead to kinematic solution at both singularity and ill conditioning, and to guarantee continuous sequence of positions of the end effect or. Furthermore, the solution to optimization and obstacle avoidance is investigated. A numerical example is shown to illustrate the approach.

Jan 1, 1989

By R. S. Austin

One third of the world's and most US kaolin is produced from Late Cretaceous and Early Tertiary sedimentary strata in Georgia and South Carolina. The kaolin is part of a belt extending to Arkansas of aluminous lateritic deposits, including bauxite. Original sediments were profoundly altered by chemical weathering during Early Tertiary time. Mining exploits those uncommon deposits where extreme leaching and chemical recombination have produced a clay of nearly pure mineral kaolinite. . Its whiteness, brightness, fine particle size, platelet shape, surface chemistry, and chemical composition make kaolin an important pigment, filler, extender and chemical compound in the paper, paint, plastics, ceramics and catalyst industries.

Jan 1, 1998

By M. Karmis

The algorithms for the mathematical modeling to predict productivity of underground room-and-pillar mining systems are well known and documented. These algorithms consider the time-varying relationships between mining equipment for a given geometty of operations as well as other constraints. This paper presents WebConSim, a newly developed, Web-based, user-friendly computer simulation tool for the Windows environment. The simulator is easily customized for use by field engineers, planning engineers and management and will help mine operators plan the optimum mining sequence for different mine geometrie and equipment layouts. Program output includes production data and equipment utilization indices, as well as time driven event chains that can be used for virtual reality presentations.

Jan 1, 2002

By James Lonergan

This paper describes the application of the Graphics Assisted Under Ground Engineering (GAUGE) software to a 2-layered room and pillar hard rock mine. The graphics- assisted mine modeling and mine planning capabilities of GAUGE are demonstrated. The system uses polygons to model the room and pillar mine design and displays the model in plan view on the graphics screen,. The planning engineer interactively specifies areas to be mined in the medium or long term. The system calculates and accumulates tonnages and grades for the user-specified areas based on the layer being mined and the particular unit operation (drifting, widening or benching).

Jan 1, 1989

By F. F. Aplan

Estimations have been made of the tonnage of raw ores and coal treated by various beneficiation processes. The amount treated by gravity concentration is substantially greater than that treated by flotation, with coal representing the bulk of the material treated by gravity means. A discussion is given of the trends and anticipated improvements in gravity methods. Except for the concentration of iron ores, magnetic and elec- trostatic separation processes find their greatest use in the beneficiation of non-sulfide ores. Exciting new developments in magnetic materials and separation process (and, to a lesser extent, in the electrostatic process) indicate a substantial increase in the application of such processes to ores and a broad variety of non-ore uses.

Jan 1, 1989

By R. J. Puchala, B. M. Hawrylewicz

High voltage electrical discharge in water causes instantaneous release of accumulated energy into water. The experiment described in this paper regards the utilization of the electric discharge phenomenon in rock splitting. The pressure in the shock waves created by the discharge inside a small volume of water enclosed in solid rock causes stresses which can result in breakage of rock. Holes drilled in tested samples were notched in order to weaken the tensile strength of the rock and achieve a uniformly directed split. The influence of the notches was theoretically analysed and compared with experimental data. Results of the tests have been statistically elaborated in order to correlate the newly-created surface to the energy supplied.

Jan 1, 1986

By G. A. Hope, K. Watling, R. Woods, I. Chandra, I. M. Ritchie

This paper presents two aspects of gold leaching research and development. The first section of the paper covers the development of innovative gold leaching processes. The research in this area has concentrated on the development of new thiosulfate leaching systems which use Fe(III) stabilized by ligands as the oxidant in place of copper(II)+ammonia. The second section will cover the development of innovative techniques such as surface enhanced Raman scattering (SERS) to study the leaching of gold in cyanide solutions. It will be shown that the use of in-situ SERS yields information which cannot be obtained using other methodologies.

Jan 1, 2005