Search Documents

By G. Lyman

The cross-belt sampler is a device that is very widely used even though it has not been ratified by the Standards associations. This paper is concerned with the bias testing of two cross-belt sampler designs against stopped belt samples and a cross-stream cutter at the belt end. The bias analysis is carried out using size distribution as the analyte and conventional t-testing and the Hotelling T squared test, which are compared for their effectiveness. The paper considers the issue of detectable bias and the statistical planning of bias tests.

Jan 1, 2010

By G. G. le Roux

The purpose of the investigation was to assess various options for increasing the efficiency of the conveyor belt transporting system used at 4 Belt Shaft at Lonmin?s Marikana operations. The reason for the investigation was to prevent the occurrence of a ?bottleneck? at the main ore passes delivering ore to the conveyor belt system, thus creating more fluent operational conditions. The options assessed for increasing the efficiency of the conveyor belt transporting system were: ?Variation of the conveyor speed ?Concurrent tipping from two ore passes on the belt ?Increase the available drive unit power ?Increasing the feed rate from vibratory feeders ?Change in belt width/belt specifications The report shows that the most preferable option to the current situation at 4 Belt, Lonmin, would be the option of concurrent tipping from two ore passes to the belt.

Jan 1, 2008

By H. Krogerus, P. Niemelä, P. Oikarinen

High carbon ferrochromium is produced by carbon reduction. No replacement for carbon as reductant has yet been developed. The reduction creates a considerable amount of CO-gas. In open and semi-closed furnaces the gas is burned when leaving the burden. In closed furnaces the formed gas is sucked out by a fan, washed and utilised as fuel. The formation of carbon monoxide is presented briefly starting from thermodynamic considerations up to solid and liquid state reduction. The volume, composition and energy content of the furnace gas are discussed, focusing on the raw materials and pre-treatment processes of the furnace feed as well as on the process equipment and control. Outokumpu has been using closed and sealed furnaces and utilising the CO-gas in its Tornio Ferrochrome Works since 1968. Today in Tornio with an annual ferrochromium production of 260 000 t CO-gas production is 186 million m3, representing 68 MWh an hour. At the same time the furnace power input is 95MW. About 98 % of the CO-gas is utilised, whereof 30% in the ferrochrome production itself. This paper focuses on the characteristics and utilisation of CO-gas. CO-gas is secondary energy, which on one hand saves primary electric and fossil fuel energy in ferrochromium production and, on the other, replaces other fossil fuels at the adjacent steel works. The characteristics of the fuel, requirements for utilisation as well as health and safety aspects are discussed. Utilisation of the gas has a high impact on the total dust and gaseous emissions and on the energy optimisation at the ferrochromium and steel works.

Jan 1, 2004

By W. Barnett

The Limpopo Metamorphic Belt is a complex geological terrane with at least three major deformational events. Tectonically juxtaposed lithology, open to isoclinal folding, crosscutting and re-activated shear zones and metamorphic gneisses and schists make pit slope design and maintenance a risky business. Venetia diamond mine?s Cut 3 is planned to reach 360 m by 2011. The difficult rockmass created problems in the original pit and a new more comprehensive slope design was necessary. Nearly 9 km of geotechnical drilling were undertaken to produce a new geological model and provide geotechnical information near the final Cut 3 face. All existing data from the pit were brought together into a database. SRK Consulting were brought into the project to audit the process and provide most of the manpower for the data analysis. Existing failures were back-analysed and the geotechnical domains identified. Analyses of only the southern domains are discussed in this paper. Geotechnical engineers can design slopes at any angle, but it is up to the managers at the mine to decide what risk they are willing to accept in a slope design. Once the issue of risk was discussed and settled in respect of the consequences of failure, each of the main geotechnical domains were analysed to produce a slope design at5% probability of failure with 15% above the first ramp. A risk assessment of the design was then undertaken to determine what risk the design placed on the equipment, personnel and the profitability of the overall mining operation. The risk assessment indicated minimal risk to the operation. One of the main assumptions of the final design is that the pit slopes will be dewatered. A project was immediately put in place to determine a groundwater model for the mine and to thereby determine the best dewatering procedure. However, it should be obvious that it is practically impossible to prevent benches from getting briefly saturated with water during storm conditions. It was therefore necessary to look specifically at supporting the crests of the ramps in the problematic southern domains to guard against the possibility of crest failure during heavy rains. The data available were re-analysed toward this objective. Spiles were recommended as the most cost-effective support system, and a probabilistic approach was used in the design. The final design has a 5% probability of failure, and the analyses indicate a strong sensitivity of the required spile spacing to the strength of the reinforcement material that will eventually be used. The pit slope parameters derived as per the discussion in this paper have just begun to be implemented at Venetia Mine.

Jan 1, 2001

A typical sub-level block cave mining extraction method employs an undercut level to establish a cavity in hard rock, and as such requires special support methods and products to be installed during the development phase. The undercut level development in the block cave orebody is then sacrificial, and support elements will eventually report to the crusher and perhaps conveyor belt systems for transportation to surface. The choice of support products installed in the undercut level development should take cognizance of the detrimental effect these could have on the mining system such as cutting of conveyor belts, obstructing crushers, safety aspects, and productivity. This work explores the probability and practicality of making use of new-generation support products to make the operation safer as well as enhance productivity in the development phase and during the undercut operation. This paper will investigate the use of glass reinforced plastic(GRP) rockbolts and GRP mesh instead of conventional steel bolts and mesh along with resin capsule-filled holes with the GRP bolts. Complementing this with thin spray liner (TSL) application as another means of creating a safer operating environment, as well as a productive support medium, will also be addressed. These proposed items are envisaged to reduce production downtime and improve the safety of our people. These items are all easy and light to handle, cuttable and crusher friendly, as they will break up during the crushing process.

Jan 1, 2012

By R. Abela

Heavy mineral sands are usually beneficiated in a spiral concentrator circuit prior to separation of heavy minerals into streams of zircon, rutile and ilmenite. The performance of the spiral concentrators is heavily affected by the presence of slimes in the rougher feed. The paper quantifies the effect of slimes content and discusses the beneficial effect of spiral feed de-sliming. The net effect of inefficient slimes removal can cause significant recovery losses of the heavy minerals present in the feed.

Jan 1, 2003

By Stefan Basista, Janusz Tomala

Modern constructions of electric ferroalloy furnaces are still based on applying in the lower "liquid" areas the standard carbon materials. What can be illustrated by the experience from several years, in the part of tap hole, hearth walls and bottom, is that so-called carbon or semigraphite microporous materials are successfully being applied. These materials, compared to the standard carbon, give better resistance to the attack by liquid metal and other wear factors. Generally this group includes materials characterised by considerable share of pores of diameters below1µm (significantly exceeding 90% of total porosity). The microporosity increases the resistance to the infiltration of the liquid metal. The effect of microporosity can be obtained by introducing silicon (or its compound) additive to materials based on electrically (or gas) calcined anthracites, electrographite and binder. Moreover, by introducing other ceramic additives, the microporous materials are more resistant to dissolution by the liquid metal. Observing the trends of "improving the materials" in the last years, it is clearly seen that the share of non-carbon additives is bigger and bigger, so we can reasonably speak of rather carbon-ceramic materials. In this paper, the survey of the most important quality criteria, which must be met by the carbon furnace linings, as well as the new testing methods will be presented.

Jan 1, 2007

The estimation of the spatial variation of the b-value of the Gutenberg- Richter relationship is important for both the general interpretation of the mechanism of rock mass response and seismic hazard assessment. The interpretation of b-value as a parameter of rock mass response is discussed in this paper. The methods applied to evaluate the spatial variation of b-value and the algorithm for obtaining the magnitude of completeness and b-value for subsets of data are presented with some verification analyses. The algorithms presented enable the automation of a spatial evaluation of b-value.

Jan 1, 2014

By W. Dziurzynski, S. Nawrat, A. Krach

The paper presents research on the influence of the goaf methane inflow on a fire. The problem was investigated by a computer simulation of a fire developing in a goaf. A relevant mathematical model of the fire was selected, which considered both burning of coal and methane. The combustion process is very sensitive on the oxygen and methane concentrations, which was indicated on graphs of the fire temperature evolution. Examples of computer simulation for various location of the fire were considerd. Analysys of results confirms the influence of the content of the goaf methane on development of fires.

Jan 1, 2003

By Y. M. Chen, H. L. Zhang, W. U. Bing, C. Q. Zhou

Multiphase flow in the widely used Vanyukov furnace was numerically studied. An unsteady three-dimensional and three-phase flow model was firstly built using the computational fluid dynamics (CFD) software ANSYS FLUENT®, and then solved with the volume of fluid (VOF) and k - ??model. The results showed that the proposed model could be used to predict the multiphase movement, the slag/air fluctuation, the vortex formation, and effects of structural and operational parameters. By fast Fourier transform (FFT), the dominant frequency of density with time signal was calculated as 0.29 Hz. The analysis of different injection flow rates of enriched air indicated that this variable has a major effect on the mean slag velocity. The peak mean velocity increased from 2.17 to 4.99 m/s while the flow rate of enriched air varied from 70 to 160 m/s. The proposed model provides a method to optimize the furnace structure and operating conditions for the best furnace performance and lowest energy consumption.

Jan 1, 2015

By Y. Jin

Magnesia ramming materials have been widely used in China instead of magnesia bricks as furnace lining materials of ferroalloy refining furnace. The paper introduces the development of the ramming material, recounts its chemical composition, physical property and application characteristics. Because of its high MgO contents and fine sintering property, the ramming furnace bottom has the properties of good refractory, monolithic construction and thermal shock resistance. The changes in mineral composition and furnace tearout characterization show the reasons for the bottom?s long service life. The obvious benefits are widely achieved, the annual saving cost in refractory is about 2 millions US dollars.

Jan 1, 2004

By C. F. Vos, J. D. Miller, J. C. Davidtz

Small replacements of C12-trithiocarbonate (C12-TTC) for dithiocarbonate (DTC)/dithiophosphate(DTP) in a reagent suite for the flotation of platinum group metals (PGM) have significantly improved the rejection of gangue. Coupled to this is an improvement in kinetics, grade and recovery of PGMs. In a pilot-plant trial, after a 5 mole per cent replacement of the current DTC/DTP collector combination by C12-TTC, large opaque bubbles were replaced by small clear ones. In addition, a similar flotation response was realized with one-third of the current depressant dosage. During a preliminary plant trial on underground UG2 ore, the initial rougher concentrates were characterized by higher PGM concentrate grades and this was in part due to improved chromite rejection. The concentrate produced from the TTC trial also exhibited a much finer particle size distribution. The overall circuit performance, which included secondary regrind and flotation, showed an increase in concentrate grade of approximately 44% while the tailings grade remained unchanged

Jan 1, 2006

By T. Kagogo, M. Neser, C. Knobbs, E. Gerryts

"Contrary to the way it is often portrayed, the average organization or company is far from being a cold, calculating machine. It is actually a highly emotive place where interaction with people is a fundamental part of its ability to perform satisfactorily.The company, through its employers, expects employees, including new graduates, to have the ability to cope adequately with this emotive environment. The graduate is frequently unable to meet this expectation because he/she has not been developed to do so. Technical knowledge is his only asset. This deficiency manifests itself in leadership shortcomings, both intrapersonal and interpersonal. Further analysis reveals a deficiency in three elements of leadership - self-awareness, oral communication, and an ability to work cooperatively in teams.To address these three elements of leadership, Sasol Coal, a subsidiary of the big petrochemical company in South Africa, sponsored a leadership programme at the University of Pretoria for their final-year bursary students in the faculty of Engineering. This programme, the Sasol Engineering and Leadership Academy (SELA), consisted of a number of interventions designed to address the three areas of self-awareness, oral communication, and cooperative behaviour in teams. These interventions varied from an intrapersonal nature to interpersonal aspects. Psychometric assessments were followed by experiential modules dealing with the three constructs.SELA was evaluated at the end of the year. The results showed a positive shift in the main constructs of self-awareness, communications, and cooperation. This was measured quantitatively and qualitatively. Conclusions were drawn and recommendations for improving the programme were proposed."

Jan 1, 2014

By C. Knobbs

Contrary to the way it is often portrayed, the average organization or company is far from being a cold, calculating machine. It is actually a highly emotive place where interaction with people is a fundamental part of its ability to perform satisfactorily. The company, through its employers, expects employees, including new graduates, to have the ability to cope adequately with this emotive environment. The graduate is frequently unable to meet this expectation because he/she has not been developed to do so. Technical knowledge is his only asset. This deficiency manifests itself in leadership shortcomings, both intrapersonal and interpersonal. Further analysis reveals a deficiency in three elements of leadership ? self-awareness, oral communication, and an ability to work cooperatively in teams. To address these three elements of leadership, Sasol Coal, a subsidiary of the big petrochemical company in South Africa, sponsored a leadership programme at the University of Pretoria for their final-year bursary students in the faculty of Engineering. This programme, the Sasol Engineering and Leadership Academy (SELA), consisted of a number of interventions designed to address the three areas of self-awareness, oral communication, and cooperative behaviour in teams. These interventions varied from an intrapersonal nature to interpersonal aspects. Psychometric assessments were followed by experiential modules dealing with the three constructs. SELA was evaluated at the end of the year. The results showed a positive shift in the main constructs of self-awareness, communications, and cooperation. This was measured quantitatively and qualitatively. Conclusions were drawn and recommendations for improving the programme were proposed.

Jan 1, 2014

By J. H. Potgieter

This paper describes two cases of corrosion that occurred in dry-process, rotary, cement-clinker kilns. In the case of the kiln with five pre-heater stages, the attack occurred primarily from sulphates that probably originated in the raw feed and fuel being used in the plant and that penetrated the refractory lining. The corrosion was similar to ash-deposit corrosion often observed in steam boilers. In the second case the plant consisted of a long dry kiln with a single pre-heater fitted to the feed-end. In this case the corrosion could be ascribed to alkali chloride penetration through the refractory-brick lining and subsequent hot corrosion of the kiln shell.

Jan 1, 2004

By N. E. Yasitli

There is a considerable amount of lignite reserve in the form of thick seams in Turkey. It is rather complicated to predict the characteristics of strata response to mining operation in thick seams. However, a comprehensive evaluation of ground behaviour is a prerequisite for maintaining an efficient production, especially when top coal winning by means of caving behind the face is applied. A comprehensive modelling of deformations and induced stresses is vital for the selection of optimum production strategy. In this study, numerical modelling and analysis of a longwall panel at Omerler underground coalmine have been carried out by using the software called FLAC3D developed based on the finite difference technique. Firstly, a 3-D numerical model of the M3 panel has been prepared. Secondly, induced stresses formed around the longwall face have been determined as a function of face advance where the face was located at the bottom of thick coal-seam. Results obtained from modelling studies have revealed that the front abutment vertical stress was maximum at 7 metres in front of the face and magnitude of front abutment stress was found to increase up to a distance of 200 metres away from the face start line. As the face was further advanced after 200 m from the face start line, there was not any significant change in the characteristics of front abutment stresses. Results of numerical analysis of the panel were in good agreement with in situ observations.

Jan 1, 2005

By M. Seeger

The demographics and the growing numbers of people provide a strong signal that the demand for electrical power in Southern Africa will grow considerably over the foreseeable future. Without a steady and increasing supply of electricity development of the continent is likely to be constrained. The inventory of solar, wind, hydrothermal, geothermal and biomass resources will probably provide sources of energy for the future The parallels between extraction of natural resources in the minerals industry and the green energy industry is striking, and the well-established project development process in the minerals industry provides an ideal and useful template for comparing the establishment and development of green energy projects. The potential levels of power generation and carbon savings are described.

Jan 1, 2010

By E. Robles

The Tati Activox® Project (TA®P) is the first step towards the implementation of the Norilsk Nickel Activox® process. The ultrafine grinding (UFG) and autoclave pressure leach process conditions are the heart of the Activox® patent. Low grade base metal sulphide concentrates are leached in the process to recover the base metals and to produce LME grade nickel and copper cathodes and cobalt carbonates. The downstream processing of the metal-containing liquor produced by this process includes solvent extraction circuits to extract and concentrate metal-rich solutions, before the various final products are obtained. This paper gives an overview of many of the relevant design aspects taken into consideration in the design of the Tati Activox® solvent extraction circuits. It addresses key design elements related to leach process conditions such as scaling, materials selection for corrosive solutions, pH control, crud formation and treatment, multiple SX trains designed to prevent organic cross-contamination, and design aspects related to the mitigation of fire risks.

Jan 1, 2009

By R. Dass

Paper written on project work carried out in partial fulfilment of B. Sc Eng (Extractive Metallurgy) degree Screening is an industrial process that splits material at a specific cut size into one fraction of particles larger than the cut size and another fraction of particles smaller than the cut size. Particles are vibrated to increase the probability of them being accurately classified and to move the oversize particles off the screen surface. In conventional screening, the screen mesh vibrates with a single frequency and the particles on the screen are all exposed to this same frequency. The Ultimate Screener (see Figure 1) is a new screen technology that imparts multi-frequency vibrations to the screen mesh so that different parts of the screen surface vibrate at different frequencies. The Ultimate Screener incorporates an additional deck that holds the multi frequency adapters as shown by Figure 2. These special adapters can transform single frequency vibrations into multi frequency vibrations. When the screen motors are switched on they begin to vibrate. This vibration is transmitted to the adapters via the body of the machine. The adapters then modify the vibration to have multiple frequencies, which are transmitted to the screen surface via resonating rings.

Jan 1, 2004

By M. A. van Nierop

Load behaviour in an industrial mill has been measured directly by inserting probes through liner bolts. The data from conductivity probes have indicated the presence of premature centrifuging during manipulation of the load mass. Overloading conditions were also encountered. Overloading and premature centrifuging both reduce the power drawn by the mill. These effects have been successfully modelled.

Jan 1, 1997