Search Documents

By M. F. G. Bruce

Two backfill systems have been developed on West Driefontein, namely the centrifuge dewatered tailings system and the cyclone-classified tailings system. Modifications to the two systems since the publication of the original paper (Close and Klokow, 1985) are discussed in addition to the results obtained. Considerable experience has been gained from the operation of the centrifuge dewatering units as well as the placement of dewatered tailings in a difficult mine environment. The centrifuge dewatered tailings method has proved successful in the extraction of a highly stressed block of ground at No. 5A Sub-vertical Shaft. The utilization of backfill support in this area made it possible to dispose of a high-grade barrier pillar. This pillar was considered necessary prior to the introduction of backfill support. The recovery of the gold from this pillar made the use of dewatered tailings backfill cost- effective, despite high labour and maintenance costs. Current experience with the bagfilling method of placing cyclone- classified tailings indicates that it is viable and requires considerably less capital investment. Although expensive at present, it is envisaged that costs will decrease once cheaper bags and other forms of stope support are used. The placement of backfill in small-diameter sausage-type bags requires no change in mining cycle and allows the backfill to be placed close to the stope face. Both backfill systems are being expanded but preference is to be given to the cyclone-classified tailings system.

Jan 1, 1988

By S. Özgen

In this study, the possibility of beneficiation of chromite tailings in the Uckopru/Fethiye-Turkey region by a combination of hydrocyclone and multigravity separator (MGS) was investigated. The two significant operational parameters of hydrocyclone, which were diameter of the apex and diameter of the vortex, and the three significant operational parameters of the MGS, which were drum speed, tilt angle, and wash water, were varied and the results were evaluated with the central composite rotatable design. In order to produce a chromite concentrate by hydrocyclone and MGS, mathematical model equations were derived by computer simulation programming, applying the least-squares method using Minitab 15. Second-order response functions were produced for the grade and recovery of chromite concentrates.

Jan 1, 2012

By C. M. G. Wortley

One of the major deliverables of the AMIRA P754 Project, which was sponsored by several major mining companies, was a code of practice and guidelines for metal accounting for the mining and metallurgical industry. These had the objective of improving the auditability and transparency of metal accounting from mine to product, thus assisting in good corporate governance. The overriding objective of mass measurement for metal accounting is to establish the mass of the particular material or component present at a specific time, or the mass flow of that component over a defined time period, to a defined accuracy suitable for metal balancing. As such, it is the first measurement in the chain that includes sampling, sample preparation and analysis, each of which introduces its own errors. Materials often contain moisture, the proportion of which must also be established in order to obtain the dry mass. They may also have to be measured as a volume or mass/mass flow of slurry, or in stockpiles or storage areas, in which case the relative density must be measured. Both the density and moisture measurement often introduce significant error. Whereas a great deal of effort has been directed at sampling, sample preparation and analysis to improve accuracy and establish the error, the same can seldom be said for the mass determination, including the moisture and density measurements. The possible major causes of error are highlighted and methods of reducing them discussed. Mass measurement can be classified into those measurements necessary for custody transfer and primary accounting of the input and output streams to a plant or operation, and measurements required for secondary accounting, or management control. The latter include intra company transfers and plant area performance, and those required for plant control only. This paper is concerned only with primary accounting measurements. The code and best practice state that the equipment should be certified (as sized) as is required for custody transfer. The most accurate and precise of the various possible methods is the static measurement of mass on a weighbridge, platform scale or a weigh bin. If static measurement is not possible, which is often the case for ore fed to a plant, possible alternatives are electromechanical conveyor belt weighers or in-motion weighing of rail trucks. In all cases the material must be adequately sampled to enable a representative moisture content to be determined to calculate the dry mass. Where material is flowing inside conduits, only certain types of the multiplicity of flow meters available may be used and, in the case of slurries, very few flow meters are suitable. As most flow meters measure volume or velocity, the density of the material must also be measured. The basic requirements in order to achieve satisfactory results for the mass, of the component of interest, are listed, as well as common problems and pitfalls encountered in practice. The measurement of the mass of stockpiles and in-plant stocks, often required for metal accounting, is often the largest source of error in metal balances. The reasons for this and methods for reducing and managing the effect are discussed.

Jan 1, 2009

By J. R. Percival, L. Ip, M. D. Piggott, S. J. Neethling

Component wear due to particle-laden flow is a significant challenge in the minerals processing industry in the handling and transportation of abrasive mineral slurries. Studying wear through experimentation is time-consuming and expensive; therefore possessing the ability to accurately simulate, understand and predict wear in these complex environments is highly desirable. The ability to predict wear is important in both the design of equipment in order to maximise the performance over the wear life of the components, as well in minimising potentially costly and dangerous failures and unscheduled maintenance.. Particle-induced wear is a complex problem, requring an understanding of coupled fluid-solid motion, geometry deformation in response to fluid-solid behaviour, moving geometries and wear modelling. Although the literature demonstrates that rebounding particles and changes to surface profiles can have a significant effect on subsequent wear rates and patterns, the challenge of implementing a model to account for this effect in complex geometries has been addressed by only a few authors in the literature. This paper describes a new wear simulator, leveraging fluidity, an open-source, massively parallel, finite element based CFD simulator capable of unstructured adaptive meshing. The wear simulator includes the ability to model particle-laden flow using representative Lagrangian particles and dynamic remeshing of geometry in response to wear and component movement. These capabilities are demonstrated using wear and the associated dynamically deforming boundaries within a Coriolis tester arm, with the results comparing favourably with the experimentally observed wear patterns. Keywords: CFD, wear, two-phase flows, anisotropic mesh adaptivity, boundary deformation

Jan 1, 2020

By O. G. Motlogelwa

Any company operating a fleet of trucks will be greatly advantaged if the associated fuel costs can be decreased. The optimal tonnage that trucks should be hauling to ensure minimum consumption of diesel fuel has been investigated. The fuel consumption in litres per ton for a fleet of trucks hauling different tonnages of iron ore was recorded in a time-motion study and the optimal tonnage was determined. The following points emerged as a result of the research: > The diesel fuel consumption in litres per ton decreased with increasing tonnage, which means that in order to improve fuel efficiency, the trucks should carry 21 t > As a result of queuing, Africa Truck Hire (one of the two equipment contractors) loses R282.57 per day to diesel that the trucks burn when they are left idling. It is thus advisable that the company adopt a policy of requiring the drivers to switch their engines off while queuing at the stockpile > Filling up the trucks during each shift or rationing the quantity of diesel to 200 litres each shift has a negligible impact on the trucks' fuel efficiency > For the company to spend 35% of their revenue on fuel, the diesel price would have to be between R8.14 and R8.78 per litre.

Jan 1, 2013

By F. Trabzuni

Elutriation of solid reactants from fluidized bed reactors can affect their process performance and efficiency greatly. Chlorination fluidized bed reactors for selective conversion of solid metal oxides to metal chlorides are used widely these days. This study provides a platform for a proper understanding of reactant solid characteristics and solid shrinkage interaction with elutriation rate constants using multi-sized particles, sand-like, ?Geldart B? chloridable materials. The study has found that actual elutriation rates of the reactive system are influenced by complex parameters? interaction including bed diameter, reactor freeboard height, bed minimum fluidization velocity, and reactant?s physical properties.

Jan 1, 2009

By P. G. Terrazas Prado

This paper presents the results of research on the development and application of a custom-made truck cycle and delay automated data collection system (TCD-ADCS) in a surface coal mining. Truck cycle and delay field data are locally stored in trucks and then synchronized and replicated through a wireless network into a centralized server containing an already-developed integrated production management system (IPMS). The system relies on motion sensing and distance travelled in order to automatically define the cycle starting/ending points, cycle time, position, and delay time. Connectivity and communication between loading equipment and trucks are also established. Communication between the equipment operators and TCD-ADCS system is via a user-friendly graphic interface. The hardware used for the development of this system consists of a rugged touch-screen personal computer, 2.4 GHz radio transmitter antenna, and a commercial GPS receiver. The system was developed, tested, and deployed at a surface coal mine in the USA. Keywords surface coal mining, truck and shovel, data collection, information systems.

Nov 1, 2013

By R. K. Brummer

A simplified two-dimensional plane strain numerical technique for the non- linear modelling of a tabular mining excavation in brittle host rock under high stress conditions is described. The model has been developed using relatively straightforward assumptions based on extensive underground investigation of the fracturing and deformation of rock at the stope face in deep gold mines on the Witwatersrand, together with observed rock behaviour under laboratory conditions. The reef rock is modelled as a linear string of yielding elements which interact horizontally, while the elastic rockmass remote from the reef is modelled using boundary element techniques. This elementary technique is shown to produce results which agree closely with the observed behaviour of the fractured rock during the mining of a remnant pillar

Jan 1, 1987

By V. E. Cogho

Optimum Coal Mine comprises numerous defunct, active, and future mining sections. The mine is primarily a large opencast coal mine; however, underground mining activities will be increasing steadily over the next five years. Opencast and underground mining activities have a significant impact on surface and groundwater resources. To ensure that the mine will be able to continue with its mining operations in the catchment, the extent of this impact requires that substantial intervention and mitigation measures need to be implemented to ensure the environmental integrity and economic use of the catchment's water resources. In developing a sustainable long-term mine water management strategy, numerous scenarios had to be analysed. The various scenarios are a combination of water and land management activities. The main components of the mine's integrated water management strategy include: ? Management of water recharge by continual and appropriate rehabilitation of disturbed land ? Beneficial re-use of impacted mine water for coal plant process water and mining operations ? Reclamation and desalination of remaining excess impacted mine water to potable standard. From the mine's long-term water balance, it is evident that the continued implementation of numerous water management actions is required to mitigate the water resources impact in a sustainable manner. In addition, the installation of a water reclamation plant at Optimum Coal Mine (15Ml/day) is a key step for the mine to achieve a zero impact target.

Jan 1, 2012

Gold Fields is the world?s fourth largest gold producer with operations in South Africa, Australia, Ghana and South America. All of Gold Fields? South African Operations are located in the Witwatersrand Basin and are intermediate to deep level underground mines exploiting gold bearing, shallow dipping tabular orebodies, which have collectively produced over 50 kt (1,608 Moz) of gold over a period of more than 100 years. Although the use of Monte Carlo as a business tool was introduced in 1964, it has only been in the last 30 years that it has gained increasing acceptance within the mining industry. However, the application thereof has been mostly limited to determination of risk in project areas. This paper however, considers the possibility of using Monte Carlo simulations to asses the underlying ?Root Cause? criteria critical to the operations management of existing mining operations. Currently, working operations have a distinct advantage over project areas as they have a wealth of historical information at hand. This, in turn, can be utilized to model distributions and relationships that can be used in Monte Carlo simulations, the results of which can be analysed to determine areas of concern. Projects can then be set up to ameliorate the effects of these and in turn reduce the risk of not achieving the operational targets. It is here that it must be stated emphatically that it should be the ?root causes? and the associated relationships that need to be emplaced within the model in order to achieve results that reflect the true causal relationship. The paper outlines possible sources of ?root cause? relationships and considers the outcomes of these in a case study on a large South African Gold Mine.

Jan 1, 2009

By W. C. Joughin

A risk evaluation model has been developed that enables the quantification of expected injuries and economic losses resulting from rockfalls associated with a support system in a given geotechnical environment, which is described in Part I (Joughin et al., 2011b). Part II presents the validation of the risk evaluation model. Underground mapping of joints and rockfalls was carried out to provide data for field calibration of the model. This survey was limited to small rockfalls, due to the relatively short period of mapping. Therefore the model was also correlated with rockfall and rockfall injury data collected by mine personnel. The analyses showed that the model provides a reasonable estimate of the expected frequency and size of rockfalls and the frequency of rockfall injuries, but further work is required to enhance the model. Three case studies are presented, which show the benefits of improved support systems from both economic and safety perspectives. This work has demonstrated that the risk evaluation model and the software developed are immediately useful, but further work is required to develop and improve the tools.

Jan 1, 2012

A number of issues relating to the computational aspects of pillar design are addressed in this paper. The computation of average pillar stress values is important when attempting to establish criteria for pillar design and in the analysis of the stability of tabular pillar layouts. One of the default ?classic? numerical methods that are used to determine pillar stresses is the displacement discontinuity method. In many instances it is not clearly understood that this approach does suffer from some limitations, particularly in relation to the fact that in coarse element simulations, the simulated average pillar stress (APS) can depend on the chosen mesh size. The nature of this error is highlighted in this paper and some strategies are suggested to bound the magnitude of these errors. It is demonstrated as well that the popular linear stiffness approximation to pillar or seam compressibility does appear to allow reasonably accurate estimates of the average pillar stress when either the pillar height is varied or when the seam modulus differs from the host rock modulus. A practical implication of this study is that if the seam modulus is noticeably lower than that of the host rock, such as for coal seams, it is important to use a linear stiffness constitutive model for the pillars rather than a ?rigid? pillar assumption. This added complexity seems unnecessary, however, when simulating hard rock pillars in mines where the seam modulus is very similar to that of the surrounding rock.

Jan 1, 2011

By A. Holder

A major mud push occurred on the 870 m production level, scraper drift block cave at Dutoitspan diamond mine in November 2011, during which it is estimated that more than 4 400 m3 of mud engulfed the west cave. The production level was successfully evacuated during the mud push with no loss of life or injury to personnel, thanks largely to mine employees being well trained in and adhering to on-mine mud rush evacuation procedures. All access to the west cave was lost as a result of the mud push. Clean-up operations are currently under way to regain access to the production level, to establish the extent of damage to scraper drifts and equipment, and to evaluate what remedial works may be required to resume production. The magnitude of the Dutoitspan mud push necessitated a detailed investigation into the key contributing factors leading up to the incident, which are discussed in this paper. Mud rush mitigation measures in place on scraper drift block caving operations at Dutoitspan, Bultfontein, and Wesselton diamond mines in the Kimberley area are critically reviewed. Recommendations are furthermore made for enhanced mitigation based on mud rush risk profiles derived for different production areas in these old scraper drift block caves. Keywords mud push, mud rush, scraper drift, block cave, mitigation factors, risk profiles, risk management structure.

Jul 1, 2013

A large body of work exists discussing the impact of grinding media on mineral flotation. Generally, the work indicates that a change to a less electrochemically active grinding environment has positive benefits on downstream processing. There is a fear, however, that these benefits may not be realized when treating low sulphide containing ores, typified by UG2 style deposits. A series of experiments was developed to test the flotation response of UG2 ores using the Magotteaux Mill® to determine if measurable differences in the pulp chemistry could be discerned using a range of grinding media types. Further, the flotation responses of the contained sulphides (chalcopyrite, pentlandite and pyrrhotite) were determined. The data collected provided strong evidence that the grinding environment can significantly influence the pulp chemistry and flotation characteristics of all sulphide minerals, even when the ore contains less than 0.5 per cent total sulphide. The results show that the change to an inert media type produced a substantial improvement in the flotation rate of all sulphide minerals, as well as the PGMs.

Jan 1, 2009

By J. A. Maritz

Since the dawn of mining, pillars have been used as primary support to ensure stable workings. Early designs were based on trial and error, after which more scientific means developed over time. A vast amount of progress has been made, especially in soft-rock room-and-pillar design methodologies, from which hard-rock design theories developed with minor changes to constant parameter values. The commonly used Hedley and Grant method for hard rock and Salamon and Munro methodology for soft rock draw on the tributary area associated with the pillar, the width-toheight ratio of the pillar, and a back-analysed strength reduction factor. In these methods, only the vertical stress, or stress normal to the pillar influences the load applied to the pillar. This investigation considers the possible influence of shear stresses on pillars in a room-and-pillar layout in single reef planes and multi-reef environments, based on elastic numerical modelling methods. The possible shear stress poses a safety and financial risk to the design process, whereby an undersized pillar would lead to unstable working conditions, whereas oversized pillars could lead to an under-utilized ore resource.

Jan 1, 2014

In the wake of the financial crisis that affected world markets in 2002, there has been an increasing international focus on corporate governance. Various corporate governance codes of practice have been introduced, such as the Sarbanes-Oxley legislation in the USA, the Combined Code in the UK, and King III in South Africa. This focus on corporate governance has increased since the most recent financial crisis in 2008, the effects of which are still being felt world-wide. In the mining and minerals industry, reliable metal accounting is essential to sound corporate governance and is also becoming a focus of increased attention and concern, particularly as the figures generated by the metal accounting system feed directly into the financial accounts of mining companies. Mass measurement, sampling, and analysis provide the input data for the metal accounting system and sound corporate governance requires that the procedures used are based on best practice and that the data generated is accurate and handled correctly, transparently, and consistently to produce the accounting reports. The AMIRA Code of Practice for Metal Accounting has been widely adopted in the industry as a means to achieve this, and the compilers of the Code have conducted numerous metal accounting audits at operations, both in South Africa and abroad. These audits have shown that there is a real need for such a code of practice. Keywords metal accounting, AMIRA Code, corporate governance, risk management.

Jan 1, 2014

Newmont is one of the few remaining large mining companies that was established in the early nineteen hundreds. The company has a long, colourful and enviable history. This paper provides highlights of Newmont?s business and technical history since its inception in 1916, its transition to a ?gold only? company in the early 1990s and progress since that time up until the present day. Details of Newmonts current gold operations and its gold production profile for 2008 are also provided in the paper Over the last 50 years Newmont has developed a host of innovative gold technologies to meet the challenges of treating the complex refractory gold ores, found at the company owned mines in the Carlin region and around the world. Details of the technologies are provided and they include chlorination, roasting, bacterial and pressure leaching, leaching gold with thiosulphate and thiocyanate, N2Tech flotation, HPGR treatment of hard and abrasive ores and, finally, the use of Hydro-Jex technology for improving gold recovery from heaps.

Jan 1, 2009

By J. Grobler, J. Zietsman

"Understanding the influence of feed material mineral assemblage on spiral separation is paramount for the successful and consistent operation of a spiral plant. Plant stability is required to maintain high recovery of valuable heavy minerals (VHM). Standard material analysis methods used in the heavy mineral industry to evaluate spiral separation behaviour are unable to quantify performance differences in the case of large variations in feed assemblage. This study illustrates a systematic approach to evaluate spiral separation performance. This technique was applied on a four-stage spiral plant. The performance information was used in a circuit simulation to clearly illustrate the importance of correct setting of the spiral splitter position and resulting spiral mass loading to ensure optimal circuit stability and maximum VHM recovery.IntroductionHeavy mineral sands deposits generally consist of naturally fine-grained, free-flowing sand due to the way in which the deposit was formed. The size of the heavy minerals market is roughly 8 Mt/a of zircon and titanium combined (Iluka, 2013). If an average combined feed grade of 5% zircon and titanium and an average combined overall product recovery of 80% are assumed, the resulting run-of-mine feed tons that would require primary spiral beneficiation is 200 Mt/a. The number of spirals required for the processing of this material, assuming 6500 operating hours per annum, an average of 2 t/h per start, and the same number of rougher spirals as other duty spirals, is over 30 000 spirals for the heavy mineral sands business alone. These numbers clearly illustrate the importance of the spiral in the heavy mineral industry.The aim of a spiral plant in the primary processing value chain of a heavy mineral process is to reject non-valuable quartz (a light mineral) from various valuable heavy minerals (VHM). The product from the spiral plant is a heavy mineral concentrate that has a reasonable grade (more than 90% heavy minerals) at a reasonable heavy mineral recovery (greater than 90%). This benchmark is fairly easy to achieve if all the mineral particles are well liberated (as in the case free-flowing sand), the feed is properly deslimed (-45 µm fraction removed to less than 5% of the solids mass), and the spirals are fed within design solids concentration (water to solids ratio) and design spiral load (dry tons per hour per start)."

Jan 1, 2017

By B. Steyn

AngloGold Ashanti?s Obuasi Mine, in Ashanti Province, Ghana, operates a plant utilizing bacterial oxidation technology. The mineralization consists predominately of arsenopyrite with gold associated in the sulphides. The plant was commissioned in 1994, at that time was the largest BIOX® plant in the world, and has been operated by AngloGold Ashanti since 2004. The constraints identified in the plantwere the flotation capacity, BIOX® feed size and disruptions to the BIOX® process. This paper focuses on the practical steps that were followed in order to increase the recovery of the plant. The original plant design was based on a head grade of 10 g/t and an overall recovery of 86.5%. In 2007 the plant was operating at an overall recovery of 79.2% at a head grade of 5.6 g/t and this has improved to 80.6% at a head grade of 5.8 g/t during the last quarter of 2008. Additional improvement to 81.5% are expected by the end of April 2009. Improvements that have been implemented include: ?Replacement of the regrind mill ?Installation of additional float capacity ?Installation of a scavenging circuit ?Installation of a complete water treatment plant. In addition we have focused on the effect of the water circuit on the BIOX® process and the steps involved in correcting this problem. The water circuit was originally designed as an open circuit and through environmental considerations the circuit was closed towards the end of 2007. The bacteria in the BIOX® are particularly sensitive to cyanide and cannot tolerate levels above 0.05ppm (free cyanide), this required extensive modifications to the water circuit. The plant improvement project is ongoing and the current scope of work should be complete by the end of April 2009. Further research and development work is being planned, which includes a ?white rot bacteria? that can consume the preg-robbing carbon and oxidize the sulphide in a single pass.

Jan 1, 2009

By L. P. Fatti

An important feature affecting the classification of a remotely sensed scene is that the data are, in general, spatially correlated. Various approaches are discussed towards incorporating the correlation between neighbouring pixels when they are classified on the basis of their spectral reflectance data.

Jan 1, 1987