Search Documents

By M. Matabane, T. Khati

"Accurate delineation of the contact between a kimberlite pipe and country rock at production level depths is a challenge due to limited geological data. Geological information is obtained from widely spaced diamond core boreholes which are drilled either from surface or from higher mining levels within the pipe. Kimberlite pipe/country rock contacts are notoriously irregular and variable, further reducing the confidence in contact positions defined by the drill-holes. At Finsch Diamond Mine (FDM), the opportunity arose to further improve the confidence in the contact positions relative to the planned slot (end) positions of each sublevel cave tunnel during the development stage of these tunnels. As a result, the accuracy of the 3D geological model has improved.The use of diamond drill core for this purpose is expensive due to site establishment requirements. The lengthy time taken during site establishment also delays the development of tunnels and support cycles, thereby extending the completion dates. FDM has reduced delays during development by adopting percussion drilling, in conjunction with gamma ray logging. The S36 drill rig is mounted on a moveable platform and does not require a costly and lengthy site establishment. The holes are generally drilled (0°/flat) on grade elevation, and these holes could also be drilled from the rim tunnels (developed in waste) into the kimberlite pipe. A single-boom production drill rig is normally used to drill holes about 20 m in length.On completion of the contact delineation drilling, gamma logging of the holes is conducted using the GeoVista geophysical sonde (or probe) to log the natural gamma signature of the dolomite/ kimberlite contact. The advantage of this tool is that the readings are continuous within centimetre intervals, and due to contrasting characteristics between kimberlite (rich in clay minerals) and dolomite, the contact position can be determined accurately. The better definition of contact positions also adds value to tunnel stopping distance in terms of developing the tunnel’s slot at the optimum distance from the contact (easier blasting of longhole rings, avoidance of contact overbreak and premature waste ingress, and other matters relating to extraction of ore from these tunnels). This method is highly successful and has reduced development costs (on-time completion), improved definition of the pipe’s contact position for geological modelling, improved blast design, and mitigated early waste ingress by maintaining the contact’s integrity."

Feb 1, 2019

By E. Lutz, M. Momayez, K. W. Brown Requist

As real-time air quality monitoring becomes more prevalent in US underground mines, it is important to provide the highest data reliability with the fewest possible sensors. Real-time sensors remain costly, and these costs are not exclusively financial; the time required to install, calibrate, and maintain real-time sensors poses a large barrier to widespread implementation. Current atmospheric monitoring systems typically rely on displaying point-specific values. This requires operators to infer real-time airborne contamination distributions. Monitoring and control software utilizing mine ventilation network (MVN) solvers has been implemented in limited cases because of their ability to simulate ventilation systems quickly, but these solvers use a one-dimensional representation of the mine, limiting spatial resolution of estimated distributions. Computational fluid dynamics (CFD) has likewise been considered as a means to improve spatial resolution, but processing times prevent its use as a basis for monitoring and control. For the real-time monitoring of airborne contamination distributions, we propose a spatial interpolation method that can estimate the distribution of airborne contaminants in near-real time. This method provides a middle ground between fast processing times and increased spatial resolution. With the use of a pathfinding algorithm and optimization through absolute percentage error minimization, this method outperforms spatial interpolation with a Euclidean distance. By providing contamination distribution information to operators, this method and its derivatives stand to outperform current atmospheric monitoring systems.

Apr 16, 2024

By F. K. Crundwell

The rate of dissolution of sulphide minerals is frequently interpreted in terms of the passivating behaviour of a layer of material on the surface. This interpretation has driven research to identify and possibly remove this layer from the surface, and thus yield higher rates of dissolution. The identification of such layers has proved difficult, with different researchers claiming different compositions for possible layers. An alternative framework has been pursued by the author and co-workers, who have argued that the rate of dissolution is governed by the electronic structure of the minerals which give rise to their semiconducting properties. Researchers sceptical of this approach have argued that semiconducting properties are only important in highly pure substances. In this paper, we review the electronic and semiconducting properties and discuss how they impact dissolution behaviour. These properties affect their colour and dissolution properties even though the minerals are not high purity substances. Keywords: Dissolution, leaching, passivation, semiconductor, chalcopyrite

Jan 1, 2020

By Axel Schulze

HUGO PETERSEN has developed from the traditional firm of the same name that was established in 1906 in Berlin and is an engineering company specialising in general plant engineering now based in Wiesbaden. HUGO PETERSEN has many years wide-ranging experience in process plant engineering, primarily in the field of Sulphuric Acid Processes and Gas Cleaning. Together with its main shareholder, Chemieanlagenbau Chemnitz GmbH (CAC), a company with over 40 years experience in the international plant engineering business, HUGO PETERSEN implements turnkey new plants from initial consultancy right through to commissioning. In addition, HUGO PETERSEN can offer its clients improvements and revamps of existing plant systems. Initial consulting, planning and implementation take place within the context of a lean company organisation with experienced engineers and specialists. In all respects, many years of experience guarantee expertise over a wide range of possible applications For clients from the chemicals and metallurgical industries, as well as those in metals processing, HUGO PETERSEN GmbH?s breadth of experience means not just an efficient introduction to new methods and processes, but also their full implementation. In addition, along with design and construction for individual components, the company?s range of services also covers supply of complete plants, as well as modernisation projects and revamps in line with local conditions and existing quality requirements With own technologies and patents in the field of gas cleaning and sulphuric acid, supplemented by licences and cooperation projects, HUGO PETERSEN ensures expertise over a wide range of applications. With specialists and expert knowledge in these fields of application, HUGO PETERSEN is your partner of choice, supporting you and bringing your acid, and project to a successful conclusion.

Jan 1, 2009

By J. Witley

"Narrow tabular platinum group element deposits in the Bushveld Complex of South Africa are typically evaluated by diamond core drilling from surface. Several short deflections are drilled from each mother hole in order to obtain multiple intersections at a close spacing (less than 1 m). Examination of the intersections from deflection drilling revealed the importance of these deflections in understanding the representivity of the borehole, obtaining an estimate of the nugget effect, and mitigating the undesirable effect of the high grade variability at the ultra-short range that is a characteristic of these deposits. The use of deflections in estimation was investigated by means of a number of techniques and scenarios in order to find the most appropriate way to use them in an estimate. A significantly improved level of confidence was gained from using multiple close-spaced intersections rather than a single borehole intersection. IntroductionThe Upper Group 2 chromitite layer (UG2 or UG2 Reef) is known for its remarkable geological continuity, being traced almost uninterrupted for tens of kilometres. However, what is often less well emphasized is the high variability in platinum group element (PGE) grade and thickness (and therefore PGE content) and internal reef stratigraphy over very short distances (several metres or even tens of centimetres).This paper examines the application of short drill-hole deflections in evaluating UG2 PGE mineral resources at Marikana in the western Bushveld Complex of South Africa."

Jan 1, 2017

By L. E. Kun, R. O. Oelofsen, E. J. J. van Vuuren

High-rate floc-blanket clarification of gold pregnant rotary filtrate was introduced at the Vaal Reefs South gold plant of the Anglo American Corporation during February 1978. A. daily 12 000 to 15 000 t of filtrate, with an average suspended-solids concentration of 350 mg/I, is continuously clarified to a concentration of less than 2S mg/I of suspended solids in a modified plant pachuca (10 m in diameter) at throughput rates of 7,7 to 8,5 ma/m2.h by the addition of 5 g/t of ferric chloride inorganic coagulant and 0,2 g/t of Superfloc NI00 flocculant. The pachuca overflow is then clarified further in seven Stellar candle pressure filters of 54,S m2 surface area to under 5 mg/I of suspended solids. The combined clarification cost when the hopper clarifier is used in conjunction with the Stellar filters is R0,0032 per ton of liquid treated, which is approximately 60 per cent lower than the cost of Stellar filtration on its own. The savings are mainly due to the reduced use of filter pre-coat, the consumption of which has dropped by 70 per cent since the introduction of hopper clarification.

Jan 1, 1979

By M. J. King, W. K. B. Loftus, H. S. Simpson

SYNOPSIS The history of the early diamond fields and primitive methods of diamond recovery are traced, giving a brief description of the improvements made in final diamond recovery processes and techniques up to the present day. In particular the emphasis is on the effect of improved equipment in reducing final hand sorting time and labour, better security and greater recovery of fine diamonds.

By Nicolle Krusberski

Potential errors in XRF analysis are discussed and investigated with specific reference to the analysis of ilmenite samples. A selection of ilmenite samples was chosen and prepared using two XRF preparation techniques: pressed powder pellet and unroasted fusion bead. The merits of the two methods have been discussed in this paper for ilmenite analysis by XRF. Recommendations have been made regarding the use of pressed powder pellets especially with regard to the mineralogical effects that were evidenced during this investigation. The fusion bead technique was found to be far more accurate and able to meet short turnaround requirements provided the calibration methodology used is specific to the grade of samples analyzed.

Jan 1, 2014

In China, thin coal seams are rich in resources but are technically challenging. The mineable reserves in these seams account for 20.4% of the total coal resources, while the current production accounts for only 10.4% of the total annual production. Characteristics such as narrow mining space, low level of mechanization, poor working environment, and high cost of mining, restrict the development of mining safety and efficiency. Recently, fully mechanized mining technology has developed rapidly for thin coal seams, the level of yield and efficiency has reached or exceeded the international standard, and some state-owned key coal mines are considering automation of their mining process. In thin coal seams with hard stone bands that contain concentrations of pyrite, a specialized software, LS-DYNA, is used to calculate the rational blasting parameters that are used in the deep-hole pre-splitting blasting. Using this method the hard stone bands are fractured effectively, and hence increasing the coal productivity. In addition, mining advance rate were increased by enhancing the level of fully mechanized equipment and safety improved by increasing gas drainage from the gas outburst prone seam located some 7 m below the coal horizon. At present, thin coal seam mining technology faces many challenges, including the low level of equipment automation, the low advance rate in mixed coal-rock ground, and the large number of the mine personnel underground. By lowering the labour intensity and improving efficiency through automation and other measures, more efficient working faces can be implemented in thin coal seams.

Jan 1, 2012

By P. N. Erasmus

This paper considers the fundamental concepts of support design for underground openings in highly stressed ground. It concludes that the conventional deformed reinforcing bar, woven mesh and cable lacing support methods that have been widely used in deep gold mines are quite in appropriate for the support of highly stressed tunnels. The following is suggested as the criterion for adequate dynamic support under rockburst conditions: the energy absorbed by a support unit (yielding through some acceptable limited displacement) should exceed the kinetic energy generated by the mass of rock that is intended to be retained by that unit. Duraset in conjunction with SRK Consulting has developed a yieldable steel tendon called the Durabar®. It is unique in the sense that it cleverly utilizes the property of the ductility of ordinary low-carbon steel from which it is made to accommodate the excessive displacement it is subjected to in the case of rockbursts or swelling ground.

Jan 1, 2009

By S. C. Essack

"Tenova Pyromet has designed a slag flow control valve that throttles the flow of slag in order to control the tapping rate. In addition, the valve has proved to be a reliable tool for closing the furnace during normal operation as well as emergency conditions. The valve makes use of a water-cooled copper element that is hydraulically operated and attached directly to the slag tap-hole. The equipment is compact, simple to maintain, and cost-effective to purchase and install. It can be retrofitted to most existing slag tapholes with minimal modifications.During the development phase, finite element method (FEM) and computational fluid dynamics (CFD) software was extensively used to model predicted operating conditions and to optimize the design. By using CFD, it was possible to understand the flow patterns inside the copper and to optimize these to improve overall performance.The slag valve was installed and commissioned in 2011/2012 on a 12 MW furnace as part of a new mineral wool plant in the USA. It has performed well since its installation despite operating under conditions in excess of the original design criteria. During the first 6 months of operation it quickly became the preferred method of closing the furnace, although the design intent was for occasional use during emergency shutdown conditions only. Since replacing the mudgun as the main method of closing the tap-hole, a few minor changes have been made to the installation in order to cope with the increased heat load and much higher frequency of use."

Jan 1, 2014

By K. Moxham, A. Smit, R. Pickering

Since the early 1970s research has been ongoing to develop a cost-effective way of continuously mining the narrow reef, hard rock, typical of South African gold and platinum mines. In the late1980s it was shown that impact ripping was a practical solution for the deep gold mines. In March2001 Lonmin and Sandvik agreed to co-operate in an endeavour to design and manufacture a prototype narrow reef mining machine with the ultimate aim of producing such a machine on a commercial basis that would enable Lonmin to create a safer and more productive environment within its mines and for Sandvik to enhance its leading position as a supplier of a new generation hard rock cutting machine. This paper describes the developed technology, the current progress of the delivery of the required objectives and the optimum mining layout for the roll-out of the mining method.

Jan 1, 2006

By S. V. Rungan

The modern mining industry is increasingly being tasked to comply with various legal, industry and social prerequisites. In addition to complying with these, the mining industry is further expected to effectively report on their compliance. Although there are many models that aid the mining industry in compliance and reporting, it is perhaps opportune for a new model to be introduced. The Compliance Spindle is postulated as a new and alternative model which is easy to understand and has the possibility of implementation in South Africa and other jurisdictions as well. The Compliance Spindle is also an effective tool to educate future compliance officers. The new model provides for all aspects of compliance and reporting and can be easily modified to take account of new developments in the mining compliance and reporting arena.

Jan 1, 2010

By G. J. McTeer, D. J. Rioux

Teck Metals Ltd operates an integrated zinc-lead complex at Trail, British Columbia, Canada. Since 1997, KIVCETTM flash smelting technology has been utilized for the treatment of zinc plant residues and lead concentrates. Trail Operations’ furnace uses four water-cooled jackets for bullion tapping. This paper provides an overview of KIVCET bullion tapping for the past 16 years, and discusses successes and challenges encountered with respect to operations, training, and monitoring.

Jan 1, 2014

By F. T. Cawood

This article offers a personal and independent view on the threats to the sustainability of the South African minerals industry. It argues that if the six identified threats of insufficient spending on research and development, general standard of education, nationalization, inadequate infrastructure, Aids prevalence and labour inefficiency are not acted upon as a matter of urgency, the future of the mining industry, along with its important contribution to the economy, is at risk.

Jan 1, 2011

By Paul Fouchè

Contents ?Purpose ?Introduction ?Why manage a mineral resource ?Sampling or tracking from source ?How can RF tracking help ?Project Goals ?RF System ?Tracer Layout ?Antenna

Jan 1, 2005

By M. M. Masood, G. Y. Raju, T. Verma

The inverse velocity method has proven to be an effective approach for predicting slope failures in surface mines by analysing displacement monitoring data. However, the accuracy of inverse velocity method predictions is significantly affected by instrumental noise and natural environmental variations, which influence the identification of different deformation stages. To enhance predictive accuracy, this study applies and evaluates three filtering techniques to velocity time series data: Exponential smoothing filter, short-term smoothing filter, long-term smoothing filter and also compares it to raw data (no filtering). A refined prediction framework, that is, filtered inverse velocity method analyser, is proposed to improve slope failure forecasting in surface mining operations. The results demonstrate that filter selection plays a crucial role in optimising failure time predictions, offering valuable insights for geotechnical monitoring and early warning systems in surface mines.

Sep 1, 2025

By Wilson. D.

The Vaal Triangle Branch of The South African Institute of Mining and Metallurgy was established on 20th November, 1986, at a meeting enthusiastically supported by local members. In attendance were special guests Dr H. Wagner (President, SAIMM) and Dr O.K. H. Stefen (Junior Vice-President, SAIMM).

Jan 1, 1987

By M. B. Díaz Aguado, I. Á. Fernández, C. González Nicieza, B. S. Menéndez

This paper summarizes the works that the Research “Group of Ground Engineering”, belonging to the Mining Department of the University of Oviedo, Spain, has been developing in close cooperation with the Regional Mining Department, since 2001, in order to control and monitor an experimental underground limestone exploitation by the room and pillars method. The aim of the current research is not only the geotechnical characterization of the rock mass (by means of laboratory and site tests) or the instrumentation of its displacements and stress changes (using convergence meters, INCREX probe, extensometers and rigid inclusion cells), but, moreover, to undertake intensive monitoring and control of such pilot mine, which is mined exclusively in order to accomplish this research. The data transmission was made on line via Internet, to achieve a full understanding of the behaviour of the experimental mine, to access data from remote locations and to visualize results from a website. All the collected information becomes input data for several numerical models using finite differences under a program developed in the research Group, ALMEC. The simulation and a final economical analysis lead to a design of an underground exploitation, at production scale, for a resource that is traditionally mined by means of open-pit process methods that could be worked underground with less environmental impact. The main purpose achieved by this exhaustive analysis is the technical and economic viability of such mine, for their optimisation for a future productive exploitation.

Jan 1, 2003

By P. L. Moolman

An approach to the design of a tailings disposal system is presented using an example from a platinum project on the eastern limb of the Bushveld Complex as a base case. The design is driven by two inputs: namely, maximizing water recovery and minimizing power cost, expressed as cubic metres and kilowatts per ton of solids deposited on the tailings storage facility respectively. The approach considers low-, medium-, and high-density platinum tailings and uses material-specific aspects such as thickening and rheology to determine the most economical option. An analysis based on direct capital and operating cost (water and electricity) shows that the medium-density scenario results in the lowest total cost per ton of tailings deposited, even though this system results in the highest electricity consumption per ton of tailings deposited. As the cost of water and electricity is likely to increase in the future, the higher-density tailings disposal options become more economical, with the paste option the preferred option.

Jan 1, 2012