Search Documents

To quickly and more reliably measure the alignment and deflection of mine guides used to run skips and cages into a mine shaft. The Problem Conventional mine guide alignment measuring systems require the use of a plumb bob and tape measure. This method is not only laborious, but it is time consuming as well. Approach Aware of the drawbacks of the current measuring method, the Bureau of Mines designed a self-contained instrument system that can accurately perform vertical guide alignment and deflection measurements by remote control. How It Works The Bureau-developed instrumentation system, called the Guide Alignment Measuring System (GAMS), is based on conventional mechanical electronics using inclinometers and displacement transducers. The instrumentation system is attached to an operating skip or cage where it functions as a completely self-contained measurement system, operating in conjunction with nor-mal travel of the skip or cage. An on-board tape recorder or a mini-computer with memory can be used to record all telemetry.

Jan 1, 1987

Enhance coal mine worker safety and productivity by developing a means to control and predict coal mine mountain bumps. Approach The Bureau of Mines has been engaged in extensive research to understand coal mine mountain bumps and their effect on underground coal mining in the United States. Information was collected on the geologic conditions, mining techniques, and engineering parameters at five mountain-bump-prone mines. Although research has not yet evolved to the point where mountain bumps can be effectively predicted or controlled, such studies are invaluable for providing clues that can lead to the development of mountain bump mitigation technology. Case Study Results and Recommendations Mountain bumps in coal mines are explosions of the coalbed that violently release the strain energy stored within it into openings created by mining. Such an event is not only dangerous to mine workers, but can cause substantial amounts of damage to mine equipment, resulting in productivity loss and downtime. In a coal mine, the occurrence may cause coal to be expelled violently from the coal face or coal pillars or cause the mine floor to heave suddenly. Coal bumps are usually accompanied by a very loud noise and tremors or vibrations. Such ground failure:; usually occur in the vicinity of an active gob line in an active retreating room-and-pillar panel, or at or near the face in an advancing or retreating longwall mining panel.

Jan 1, 1989

Reduce the dust levels to which jacksetters and helpers on auger mining sections are exposed by identifying viable, effective methods for control-ling respirable dust on these sections. Approach The Bureau of Mines con-ducted laboratory tests and respirable dust surveys to identify the factors that distinguish clean auger mining operations from dusty ones. Study Results Results of the Bureau's study revealed that ventilation is the most important element of auger mining dust control. The four must important venitilation parameters are airflow, curtain configuration, curtain setback, and curtain installation.

Jan 1, 1988

Decrease dust concentra¬tions of longwall face workers by keeping them up¬wind of the headgate stage loader and crusher. Approach Direct the face airflow from tailgate-to-headgate, the direction of coal transport. How It Works Ventilation is the primary method of dust control on longwall faces, and the most effective ventilation control is to put workers upwind of dust sources. Recent ad¬vances in longwall dust sampling by the Bureau have shown that on some faces, the headgate crusher and transfer points are signifi¬cant sources of dust -some¬times making up more than half of the total dust to which the face workers are exposed. Also, when the air is coursed from head-to-tail, the relative velocity between the air and moving coal on the face conveyor can cause dust entrainment from the conveyor, particularly if the coal is dry. On the faces where these dust sources are a signifi¬cant problem, they may be eliminated by coursing the air from tailgate-to-headgate, provided that the mine roof is stable enough to permit the necessary intake of the tailgate along with an aux¬iliary intake at the headgate.

Jan 1, 1982

By S. R. Zimmerley, John Gross

"The investigation discussed in this paper was undertaken to obtain fundamental data on crushing and grinding and has been confined, so far, to work on quartz.The results of crushing or grinding have hitherto been judged entirely by the amount of the various-sized particles produced, based. on sieve sizing for particles above 74 microns in size and on microscopic measurement or elutriation for particles below 74 microns - a method which could give only a general idea of what had been accomplished.There was a distinct need of a ""yardstick"" for the measurement of crushed material. It appeared that no advance in the fundamental investigation of crushing and grinding could be made without a reliable method of surface measurement and that such a measurement would have to be based on some property of the surface of the crushed material.A number of attempts based on various surface actions, such as adsorption and heat of wetting, were made to measure surface on quartz particles, but all gave unsatisfactory results. After some preliminary work it was decided that a dissolution method based on Wenzel's law-- ""the reaction velocity between solids and liquids is proportional to the area. of contact""4 -- would be the most feasible.Early use of the dissolution method had been made for surface measurements5, and lately Dr. Geoffrey Martin and his coworkers in England used the dissolution method to determine surface on quartz. They compared the amount of quartz dissolved from a sample in one hour by a hydrofluoric acid solution, with the amountdissolved from a measured quartz cuboid6,After investigating the solvent power of sodium carbonate, sodium hydroxide, and hydrofluoric acid for quartz, hydrofluoric acid was selected as the most suitable solvent, and a dissolution method was developed which gives very reliable results.During the dissolution of quartz in hydrofluoric acid, the reaction velocity changes for two reasons: there is a change in concentration of solution, and a change of surface of the solid. The amount of quartz dissolved in a definite period of time is therefore not a true measure of surface. If, however, the reaction velocity or rate of dissolution for various periods of time be plotted, a curve will be obtained which, if extrapolated to the zero time ordinate, will give the rate of dissolution before any change of surface or any change in the solvent has taken place, and which is a true index of surface. This rate of dissolution, expressed in percentage of the original sample at the zero time ordinate, is designated herein as the ""Initial Rate"" or as simply ""I. R."""

Jul 1, 1928

By Martin Berman

The Bureau of Mines has investigated the mineral matter content of 38 American coals using X-ray fluorescence. Measurements of the Ka intensity for magnesium, aluminum, silicon, sulfur, calcium, and iron permit the determination of those elements as well as an indirect determination of the ash con-tent of the coals. The percentage of each of the six elements was corrected for absorption by all six elements as well as by hydrogen, carbon, nitrogen, and oxygen. It made little difference whether the values used for hydrogen, carbon, and nitrogen were obtained from chemical analysis or whether average values for all coals were used. In all cases, oxygen was obtained by difference. The correction for absorption by all these elements involved the inversion of a 6 X 6 matrix and was performed by computer. Assuming that the elements magnesium, aluminum, silicon, calcium, and iron were present in the ash as oxides, the quantity of ash was determined. The results for the mineral elements as well as for ash and oxygen were in good agreement with chemical results. Particle size was found to have a significant effect on fluorescence intensities. A study of size effects was made for pyrite particles, since the sulfur content of coals is of particular interest. Theoretical equations were derived and verified relating the intensity to particle size. It was found that the coal samples must be ground to less than 2 microns. Sulfur appears in several forms in coal, and the effect of sulfur form on intensity was investigated. It was found that the Ka intensity was independent of sulfur form but the Kß intensity varied with the type of sulfur. Thus, the Ka intensity was used for determination of the quantity of sulfur present. Utilization of the sulfur KB intensity did not permit a determination of the proportions of sulfur forms present in coal. However, for synthetic mixtures of cystine and pyrite in carbon black, measurement of sulfur Ka and Kß permit determination of each constituents from measurements of sulfur intensities alone.

Jan 1, 1968

By Michael G. Zabetakis

The process of ?gasfreeing? has been defined3/ as "* * * the removal of oil and vapors from tanks, pipelines, and compartments to render such spaces safe for the intended work," Generally, part or all of a vessel is gasfreed for one of several reasons: Periodic cleaning; tank inspection or repairs; shipyard overhaul or major repairs; or change of cargo, Curing the gas- freeing, flammable or explosive4/ mixtures (mixtures through which a flame can propagate after ignition by an open flame, heated object, electrical charge, or other means) may be produced. These mixtures create an explosion hazard, as the pressures produced after their ignition are often great enough to completely demolish the vessel and kill all those aboard, This paper outlines a study by the Federal Bureau of Mines of the gas explosion hazards likely to be encountered while gasfreeing a vessel compartment. To better understand these hazards it will first be necessary to review the language used in gas- explosions work. This language is considered in the following sections. Inert gases such as carbon dioxide, nitrogen, water vapor, and others can be used to decrease the range of combustible-vapor concentrations in which flammable mixtures are formed. Sufficient quantities of such gases can often be added to cause a mixture that originally was flamable to become nonflammable. Unfortunately, the use of water vapor in this application is complicated by the fact that elevated temperatures are required to keep the water in the vapor state. In practice, it may be difficult to maintain these elevated temperatures throughout the space (such as a cargo tank) to be inerted for any length of time. Accordingly, where other inert gases are not available, it may be desirable to gasfree a Lank by using heated air. To do this, the combustible vapors should be flushed as quickly as possible from the space to be gasfreed. In a properly designed system, large tanks were gasfreed with a littlee as 6 volumes of air per volume of tank capacity.

Jan 1, 1961

By B. J. Scheiner

Carbonaceous gold-bearing ores of the type that occur in north-central and northeastern Nevada were investigated by the Bureau of Mines as part of its Heavy Metals Program. Specific objectives were to identify the carbon and organic compounds that prevent adequate gold recovery from the ore by cyanidation and to develop an economical process that would overcome the detrimental effect of the carbonaceous constituents. Activated carbon and long-chain organic compounds containing sulfur and nitrogen were found in the ore. Part of the material consisted of stable gold organic complexes. A mild oxidation technique that allowed gold extraction as high as 96 percent by subsequent cyanidation was developed. A variety of oxidants was shown to be effective in improving gold recovery, including chlorine and sodium hypochlorite (NaOC1). An electrolytic oxidation process was developed that was particularly advantageous from an economic and effectiveness standpoint.

Jan 1, 1971

Reduce dust on long wall faces by using a gob curtain to lower air leakage Into the gob and raise the airflow along the face. Approach A brattice curtain (gob curtain) Is hung between shield #1 and the rib in the headgate entry forcing the ventilating air stream to make the 90° turn and stay on the face side of the shields rather than leaking into the gob. How It Works Air leakage is greatest in the headgate area because the gob behind the first few shields remains open due to the roof bolts in the headgate entry. In addition to the open gob, there is a large gap between shield #1 and the rib. Prevention of air leakage behind the shields is accomplished by the Installation of a curtain between the first shield and the rib extending from the roof to the bottom. The curtain Is advanced with the shield line each pass and is helpful In maintaining a sufficient air quantity along the face. The biggest Improvement due to this curtain is seen in the first 25-30 shields where the Increased air volume lowers dust concentrations through dilution.

Jan 1, 1981

By James W. Vogh

The report covers initial findings in an experimental program to identify diesel exhaust odorants and determine their contributions to diesel odor. The approach was to isolate selected component groups from exhaust and to evaluate the contribution of each group to exhaust odor. Results were obtained for those carbonyls and phenols that could be isolated from exhaust through inter-mediate conversion to oxime derivatives. Unsaturated aliphatic aldehydes and sterically hindered carbonyls were not included. Hydrocarbons intermediate in the diesel range were "also evaluated and an odor contribution was found from those of the aromatic group. The evaluated carbonyls, phenols, and hydrocarbons were found to account for about 20 pct of the total odor in exhaust from an indirect-injection engine during idle. For exhaust from the indirect-injection engine operating under load and from a direct-injection engine at no load, these compounds were found to have no significant levels of odor.

Jan 1, 1972

By Lloyd A. Morley

To reduce safety and production problems, it is essential that the electrical operating characteristics of coal mining equipment and their electrical subsystems be clearly understood. The Bureau of Mines and the Pennsylvania State University have developed techniques to monitor and analyze several of the critical parameters. A unique system for measuring traction locomotive consumption at the machine has been assembled and utilized. Conclusions from 27 continuous miners show that voltage levels are directly tied to machine efficiency. The Bureau of Mines and Pennsylvania State University, along with West Virginia University, are currently monitoring and accessing mine power transients. Results exhibit that voltage transients of three to five times the line -to-line value are common on underground distribution systems.

Jan 1, 1975

Provide a method for obtaining in situ measurements of coal cutting forces which are needed for mining machine design. Approach A portable in-seam testing device is carried to the face of an underground coal mine heading to measure the cut-ting force encountered by a continuous miner pick directly at its maximum depth of cut. How It Works The tester frame is attached directly to the coal surface with four one inch diameter threaded studs resin-bolted into 1-1/4 inch diameter holes which are drilled 30 inches deep. Spherical nuts and washers compensate for misalignment between the bolts bearing plate, and traverse beams. Spacers can be placed over the studs to assure that the traverse beams remain in the same plane. Cutting forces are applied by a hydraulic cylinder that moves the pick of the tester through a twin-chain arrangement which gives a 20-inch cutting stroke with

Jan 1, 1982

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

3. Preliminary Evaluation of Mine Sealing Techniques As the first stage in the development of a technique for the remote sealing of mines, a state-of-the-art survey of various mine sealing techniques was conducted. This was expanded to include a review of different materials offering some potential for use as a mine sealant. Techniques for the remote placement of materials for other applications were evaluated, and system concepts for dis¬tributing remotely placed materials were developed. This preliminary review led to the development of a functional description of a general mine sealing technique to meet the specified conditions. Various potential system configurations were synthesized. These were subjected to a preliminary evaluation based on estimated confidence in system performance, development risk, cost, and sealing time. Based on this preliminary evaluation, promising mine¬sealing techniques were selected for further development. This section presents a review of the following: (a) Techniques for constructing permanent seals from within a mine. (b) State of the art in remote sealing for mine fire control. (c) Techniques for remote placement of materials for other applications. (d) Systems for distributing remotely placed material. (e) Materials for mine sealing. (f) Synthesis of remote mine sealing concepts.

Jan 1, 1973

Improve the dust control effectiveness of dry collection systems on surface coal mine drills. Approach Use a dust pelletizer to convert the respirable dust particles discharged by the dry collector into dust pellets that present no health hazard. Background Blasthole drills are well-known sources of respirable dust that can contain significant amounts of quartz. The drills frequently use a dry cyclone-filter type collector that can obtain dust reductions theoretically greater than 95 pct. However, surface mine drills using dry collectors typically have three major dust sources that significantly reduce the overall effectiveness of the collection system: (1) the dust collector dump cycle, (2) drill shroud leakage, and (3) leakage around the drill stem seal in the drill table.

Jan 1, 1989

To produce industrial-grade titanium castings by processes that are nonpolluting and lower cost than the currently used rammed-graphite process. Approach Foundry-grade zircon and olivine sands, bonded by waterglass or bentonite, are used to make shell or rammed molds which require relatively low-drying temperatures and do not generate noxious fumes during drying or casting. Procedures Three separate processes have been developed which meet the stated pollution and cost goals. These are: 1. Waterglass-bonded rammed zircon or olivine sand molds are dried at 480°F, zirconia washed, redried, and used in an inductoslag or skull-casting furnace. 2. Waterglass-bonded zircon or olivine sand shell molds are formed at 560°F, cured at 620°F, zirconia washed, dried at 480°F. and used in an inductoslag furnace. 3. Rammed zircon and olivine sand molds are bonded with western bentonite, zirconia washed, dried at 980°F, and used in an inductoslag or skull-casting furnace.

Jan 1, 1981

Reliably detect fires by sensing sub-micrometer-sized particles released into the air by smoldering or burning materials. Approach An extremely sensitive, ionization-type fire detector has been built that continuously draws air samples through its ionizing field and collects the ionized smoke particles downstream, thereby generating a proportional electrical output signal. (An offshoot instrument measures the size distribution and number of sub-micrometer particles in air.) How It Works Mine air to be monitored is drawn through the instrument assembly by a small pump. A pre-filter and cyclone remove dust particles and other particles larger than 0.6 micrometer diameter. The air and remaining aerosol-sized particles flow through a gastight tube which contains the detector. See diagram. Smoke and other sub-micrometer-size particles moving Into the detector, pass through an Ionizing field, and are struck by alpha particles released from radioactive source located on the axis of the tube, The alpha particles move radially outward until they strike smoke particles or molecules of air or water. When struck, a smoke particle or molecule loses an electron and becomes positively ionized.

Jan 1, 1979

By Stephen C. Tadolini, Thomas M. Barczak

An underground investigation was designed and implemented by the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of pre-driven longwall recovery rooms supported with pumpable concrete roof supports. The pumpable roof supports were instrumented with hydraulic pressure cells to measure support loading. Displacement of the support was also measured to assess the support reaction to ground movements. Movement up to 12.5 m (40 ft) into the roof was measured with sonic probes and multipoint extensometers. Borehole pressure cells were installed in the panel fender and outby pillars to evaluate load transfer. Shield loading was also assessed to determine the impact of the panel fender yielding on face loading. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 3.12 m (10 ft) from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 15-20 cm (6-8 inches) once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 10 m (32 ft) horizon with total deformation ranging from five to 10 cm (2 to 4 inches), indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in instabilities that can lead to catastrophic results. Understanding the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields is providing valuable information for the refinement of the NIOSH Ground Reaction Curve for standing and intrinsic roof support system design.

By William G. Gruzenaky

The separation of yttrium and the individual rare-earth elements (lanthanons) from mixtures in which they occur has been a difficult problem through-out the years. Because of the increased interest in the various uses of these metals, the economy of their production may become of great importance. Studies relative to this problem, undertaken at the Federal Bureau of Mines Albany Metallurgy Research Center, resulted in the development of a solvent extraction method by which yttrium can be separated from the rare-earth metals. A separation factor of 10.93 was obtained between yttrium and cerium from a single-stage extraction, and a factor of 1.78 was obtained between yttrium and erbium from a multistage system. The valuable metals were extracted from euxenite by caustic soda fusion or by chlorination, and several separation methods were investigated. Partial separation of the yttrium and rare-earth element fraction was made by chemical methods and by solvent extraction. Thermal decomposition of aqueous rare-earth nitrates or selective ignition of yttrium and rare-earth oxalates yielded a fraction enriched in cerium. A fraction enriched in the light rare-earth elements resulted from a double sulfate precipitation, whereas a potassium ferrocyanide pr cipitation yielded a fraction enriched in yttrium. Precipitation with dimethyl phosphate yielded a fraction enriched in yttrium and heavy rare-earth elements. Enriched fractions were obtained with several solvent extraction systems. A system consisting of rare-earth nitrates, nitric acid, and tri-n-butylamine-3 methyl-2-butanone favored the separation of yttrium from the heavy as well as from the light rare-earth elements.

Jan 1, 1961

By W. E. Anable

A 180° magnetic deflection residual gas analyzer mass spectrometer with a mass range of 2 to 200 amu was used to study the nature of gases evolved during arc and electron-beam melting of certain reactive and refractory metals. The partial pressure of residual gases over molten Mo, Hf, Ti, and Fe, was found to be similar: Water and hydrogen were evolved from the samples and from the furnace components, carbon dioxide and carbon monoxide resulted from deoxidation of some of the melts. Argon and acetone were residuals in the system, and methane was a decomposed organic compound from the oil diffusion pump.

Jan 1, 1969

By Wilbur I. Duvall

In this report, the Bureau of Mines presents a theoretical solution for the stresses and displacements in an infinite elastic plate containing a circular hole the boundary of which is loaded by applied radial stresses over four separated arcs. The problem solved is a two-dimensional approximation of the stresses and displacements developed by a large tunnel-boring machine anchored in a circular tunnel. Analysis of the solution shows that the tangential tensile stresses induced on the boundary of the circular opening can be minimized in the roof and maximized in the floor of the opening by proper spacing and loading of the four arcs.

Jan 1, 1967