Search Documents

By R. T. Stull, L. E. Geyer

"Previous Work:As outlined in previous papers* ond clays for graphite crucibles have been tested at the plants of the Detroit Lubricator Co., and the Detroit Copper and Brass Rolling Mills, Detroit, Mich.These tests indicated that there were two American clays (Missouri pot clay and Illinois kaolin) that tested better than the Klingenberg (German) clay. Dorset (English) ball clay was tenth in the list.Making the Crucibles:After it had been determined that American clays can be used successfully in graphite crucible manufacture and service, the next step in the investigation was to determine the value of American graphites as compared to the foreign, These final tests were carried out at the plant of the Detroit Lubricator Co., through the courtesy of Mr. G. B. Duffield. The crucibles, as previously. were made at the plant of the Vesuvius Crucible Co., Swissvale, Penna., from a formula compiled by the Bureau of Mines and under the supervision of Bureau engineers.The graphites to be tested were given an initial to indicate their source. The number of crucibles made and shipped are set forth in Table 1."

Nov 1, 1923

Control dust generated during undercutting in salt mines without causing ore-solubility problems that result from excessive water use. Approach A foam generator was developed to provide a reliable foam to control dust on cutting machines used in mining water-soluble ores. The system was designed to keep total foaming agent/water mixture flowrates below the flow-rates characteristic of water-only systems. The foam generator consists of a reservoir to hold the premixed agent and water, a metering pump, and a small compressor to aerate the mixture. The system is compatible with all cutting machines. How It Works One of the current wet-bar techniques, the through-the-bar trickle system, pumps water through a pipe in the cut-ting bar to its tip placing the water behind the kerf. If the pipe conducted foam effectively the foam would be released in the kerf where it would mix with the cuttings and the dust produced by the chain. For improved foam delivery, however, it is recommended that the pipe be replaced with an external channel welded along the top of the bar. This provides excellent dust control while avoiding the accumulation of copious quantities of foam in the heading. The system is very simple. The foam generator is a 50-gallon tank filled with a mixture of water and foaming agent. The mixture is pumped through a wye fitting to a second line where it is mixed with compressed air, (300

Jan 1, 1984

Reduce longwall shearer operators' dust exposures by more effectively suppressing the dust generated by the upwind cutting drum. Approach Direct more of the shearer water supply to the upwind drum, thus reducing the shearer operator's exposure to respirable dust while making more efficient use of water. How Proportioning Permits More Efficient Use of Water On most longwall mining operations, the cutting action of the shearer drums is the primary source of dust. Al-though the amount of dust generated is directly related to the amount of coal and rock cut by the drum, the exposure or the shearer operators to dust depends more on their work position relative to the upwind drum. When cutting with the airflow, the upwind drum, cutting bottom coal and floor rock, is the primary generator of dust reaching the operators. The lead drum is downwind of both shearer operators and is thus of less concern. (See diagram). When cutting against the airflow, the lead drum is upwind-taking a full cut, including roof rock-and both shearer operators may be exposed to very high levels of respirable dust. Currently, water sprays mounted on the cutting drum provide the most effective method of controlling dust from longwall shearer drums, and all longwall mining operations use some type of bit flushing or cavity filling water spray system on the cutting drums. Bureau surveys of longwall operations, conducted as part of its research program to reduce respirable dust, have indicated that six longwalls with better than average compliance records use higher than normal water flowrates to the cutting drums. The average water flow to the shearers at these six operations was approximately 60 gpm-about 50 percent more water than is normally supplied to double-drum longwall shearers.

Jan 1, 1982

Develop a training program to help mine workers effectively fight small fires in underground Goal mines. Training would enable miners to make rapid judgments on whether to attempt extinguishment, and how best to use the firefighting equipment on hand. Approach Fire reports were analyzed to define and delineate physical and behavioral variables which affect firefighting activities, and to determine effective procedures for extinguishing small fires. A course was then designed to train miners in such procedures. Finally, the course was reviewed by industry experts and administered to a group of miners to determine needed revisions and to validate the course. How It Works Analysis of fire data showed that six items should be emphasized in teaching proper fire response: 1. Alertness to fire potential. 2. Immediate power cutoff. 3. Internal, external communication. 4. Teamwork in fighting fires. 5. Role of ventilation and position of men inby the fresh air side. 6. Effective use of fire suppressant materials.

Jan 1, 1983

By S. P. Howell, M. W. Von Bernewitz

"Introduction. The first short—flame explosives were made in the United States during the year 1902, then the mount was 11,300 pounds. In 1902 they were designated ""permissible explosives"", and were required to meet specific tests. By 1912 the total consumption thereof had increased to 24,630,000 pounds, equal to 5 per cent of the total quantity of all kinds of explosives produced in this country; while in 1922 the total was 43,429,000 Pounds, or 10 per cent of the production, and 18 per cent of the explosives used for the mining of coal.Each year the Bureau compiles statistics of explosives, one important object of this being to show the extent to which permissible explosives are replacing other classes of explosives in coal—mining operations, and the influence of such replacement in reducing the number of accidents caused by explosives in this class of mines. The consumption of permissible since 1916 has considerably exceeded the quantity of high explosives (dynamites, etc.) used in coal mines. While the increase in use of permissible is good, the replacement of other explosives therewith is not nearly as good as with be, considering the known general efficacy and safety of permissibles."

Mar 1, 1924

By L. A. Johnson

The Bureau of Mines analyzed three cores from the south Seep Ridge area of the P. R. Spring tar sand deposit of northeastern Utah. Four tar sand zones are indicated in the area. The zones range in average thickness from 13 to 24 ft. The total net thickness of the tar sand in the three coreholes ranges from 71 to 112 ft. The tar sand occurs between the depths of 27 and 254 ft. It has good porosity, 25.6 pct of bulk volume; high permeability before and after oil extraction, 819 and 2,218 md, respectively; but a relatively low oil saturation, 36.5 pct of pore volume. Gravity of the oil ranges from 8.20 to 16.5° API.

Jan 1, 1975

By A. B. Hooker

Investigations at the Pittsburgh Experiment Station have shown that the satisfactory operation of aflame safety lamp depends not only upon proper design and assembly of the lamp but upon the kind of fuel used, and that much of the trouble experienced with permissible flame safety lamps at mines is due to the common use of motor gasolines, none of which is suitable in the present types of permissible flame safety laps. This report gives the results of a limited study to determine what satisfactory fuels are available, the specification limits of such fuels, and to suggest modifications of assembly and care of the lamps to improve performance with any satisfactory fuel.

Jan 1, 1938

By F. N. Kissell

The Bureau of Mines used sulfur hexafluoride (SF6) tracer gas to evaluate the effectiveness of gob ventilation and/or sealing practices at three coal mines, each having different problems associated with their mined-out areas. The purpose of these ventilation studies was to better understand whether current techniques employed for ventilation or sealing are successful at minimizing the potential for gob fires and explosions. The work performed at each mine is discussed: One is a long-wall operation that uses ventilation to carry off hazardous gases, and two are room-and-pillar operations, each with far different concerns, that seal off the gobs to isolate them from the main mine ventilation. In all cases employment of the Bureau's SF6 tracer gas technique resulted in answers to questions raised by the mine operators concerning the effectiveness of their gob ventilation or sealing practices in preventing mine fires.

Jan 1, 1986

To find solutions for common safety problems encountered in the handling of trailing cables, based on observations at many different surface mining operations. Approach Practices in handling trailing cables were Investigated through personal visits to over 40 mines, supplemented by visits to cable manufacturers and cable repair service companies. The most effective solutions to the safety problems en-countered were noted and are described In the project final report. Examples are given in this Technology News. Accident Experience Most cable-related injuries occur as a result of workers lifting, pulling, tripping, or being struck by the cable. The Table gives the frequency of occurrence for injuries reported during a recent 3 1/2 year period.

Jan 1, 1982

Develop improved blasting practices that can help to curb overbreak in highwalls at surface mines, thereby reducing the hazards of rock-falls to workers and equipment, The Problem The serious hazard in surface mining is the falling of rock from highwalls. Poor highwall stability is caused in part by geologic conditions, but often is aggravated by faulty blasting practices, where the explosive energy not only fractures the rock to be excavated, but also damages the rock that borders the excavation. This reduces the general stability of the hlghwall and increases the rockfall potential. The probability of injury to mine workers or damage to equipment associated with exposure to the highwall increases with the height of the highwall and the extent of its overbreakage. Most rockfalls occur in the first 15 days after a new highwall is exposed. This statistic is significant since most of the work below a highwall is done during this period. The area of greatest hazard is within 25 ft of the toe for rocks that fall vertically, and up to 90 ft from the toe for falling rocks that are deflected by the highwall during their descent, The workers most frequently involved in such accidents are dozer operators, ground laborers, and shovel operators or oilers.

Jan 1, 1985

By Larry G. Stolarczyk

1.0 FRAMEWORK FOR COMPARISON This document describes the decision factors that bear on the selection of the modulation process for the wireless underground medium frequency (MF) communication system. The selected modulation process must satisfy the Bureau of Mines stated objective of improving general communications within an underground mine. The improvement being sought includes the development of a wireless communication technology of measurable benefit to both mine safety and mine productivity. The improvement will allow wireless communications paths to exist between roving miners. The wireless communication paths will also be made compatible with the existing underground telephone system to extend paging and voice communication throughout the underground mine. The new wireless equipment will include man-pack, vehicular, repeater, and base station transceivers. Repeaters and base stations will feature coupling networks for interfacing with the existing telephone circuits. Frequency modulation (FM) and single sideband (SSB) modulation processes are analyzed in view of the special conditions associated with underground mining. Of primary importance is the tremendous electrical noise generated in an operating mine that could adversely affect communications quality. High noise coupled with high attenuation rate of near field signals forces the communication system to be inherently short range. Fortunately, near field signals can propagate over great distances on underground wires and cables. The framework for comparison is generated by presenting all factors that

Reduce costs of surface mine reclamation by improving bulldozer operating efficiency. Approach A draft power indicating system helps bulldozer operators adjust blade height and other controls for maximum load movement, by continuously indicating the rate at which work is being done. How It Works This system continuously measures both the push of the blade against the overburden, and the true ground velocity of the bulldozer. It multiplies those quantities to determine the real work rate of the machine. The system consists of a velocity sensor, a blade load sensor, processing circuits, and a work-rate indicator. The processing circuits include an analog multiplier which has an output signal representing the draft power (velocity x load = power). The draft power, or pushing power is a measurement of the work rate at that moment.

Jan 1, 1979

By Charles E. Whieldon

This report presents the results of a study on part of the Smithfield oilfield, Wetzel County, W. Va. The primary purpose of the investigation was to determine the original and the present volume of stock-tank oil in the formations and to investigate the feasibility of waterflooding the Gordon Stray, Gordon, and Fourth sands underlying the I. D. Morgan lease. The study was based on laboratory core analyses, geophysical well logs, geologic considerations, and various field prediction data from the I. D. Morgan lease. The Bureau found that, of the three sands cored, the Gordon Sand was the best prospect for waterflooding, and that a properly engineered water flood should recover 136 to 230 barrels of oil per acre-foot from this formation.

Jan 1, 1967

By Forrest T. Moyer

THE SAFETY record of the mineral and mineral-fuel-mining-and-processing industries retrogressed slightly in 1964, as indicated by the 3-percent increase in the frequency rate of all injuries. A slight improvement in the fatality rate was more than offset by the less-favorable rate of occurrence of nonfatal injuries. The overall-operating activity of these industries was lower in 1964 as measured by slight declines in employment and total man-hours of worktime. Injury Experience.-The rate of occurrence of all disabling work injuries in the mineral industries was 18.00 per million man-hours. This overall rate in 1964 comprised frequencies of 0.29 for fatal injuries and 17.71 for nonfatal work disabilities, which compared with respective rates of 0.30 and 17.20 in 1963. Fatalities totaled 538 or 30 less than in 1963. However, the total nonfatal disabilities of 33,151 in 1964 was 492 higher than in the preceding year.

Jan 1, 1965

Reduce rockfall fatalities and injuries by using innovative blasting practices to reduce damage to the rock at the excavation limits with little or no increase in cost. The Problem Falls of highwall have been a leading cause of fatalities, injuries, and equipment damage in the surface mining industry. Although the number of highwall falls is not great, when such an incident does occur it is about 14 times more likely to be fatal or result in severe injury and damage to equipment than other types of surface mine accidents. Overbreak or damage to the rock from poor or improper blasting practices is a major factor contributing to rock falls. Presplitting or cushion blasting is the technique most often recommended for improved wall control. This type of blasting however, adds to drilling and blasting costs and is not universally accepted by the industry. Air gap presplitting techniques, also called air decks, are currently being used in some mines as a less costly alternative to conventional presplitting. Approach Blasting can cause highwall damage, but proper blasting techniques have been shown to reduce the magnitude of rockfall problems. In preventing rock falls, it is important to maintain the natural strength of the rock structure to the greatest extent possible. Improved blasting practices have three main advantages: 1) they are preventive rather than corrective in nature; 2) they are cost effective; and 3) they have a very low impact on the mining operation when properly implemented. New ways of evaluating highwall integrity, such as seismic refraction tomography, were investigated.

Jan 1, 1991

Provide means for rapidly re-establishing ventilation control in metal mines after blasting, for emergency applications, and for routine temporary use. Approach Two quickly-installed, parachute-like stoppings have been developed and tested by the Bureau's Pittsburgh Mining and Safety Research Center. How the Parachute Stopping Works The parachute stopping can be fastened to an existing anchor point, opened, and effectively block the air flow, in less than two minutes. Because the parachute stopping tends to be self-scaling, its performance is generally better than that of conventional fabric stopping. However, the periphery of the parachute stopping must be longer than the periphery of the mine opening, Figure 1 shows the parachute stopping deployed in a mine entry. To reduce leakage during routine use, the cloth at the periphery of the parachute stopping can be adjusted and then anchored at several points as necessary. This extra adjustment can also be done after the initial installation during mine rescue or mine recovery.

Jan 1, 1977

By Alla D. Mah

The heat of combustion of TaC0.996 was determined by oxygen bomb calorimetry to be -302.8 ±0.4 kcal/mole. The corresponding heat of formation of TaC0.996 is -35.4 ±0.5 kcal/mole, and the calculated heat of formation of TaC1.00 is -35.5 ±0.5 kcal/mole.

Jan 1, 1965

By Stephen A. Hare, O&apos

The melting, casting, and welding of the Raney nickel alloy (42 pct Ni-58 pct A1), a methanation catalyst useful in coal gasification, were investigated. Melting was done in graphite crucibles by heating aluminum and adding nickel using a cryolite slag cover. Casting conditions were found to be optimum when the melt temperature ranged from 1,125° to 1,200° C and the mold temperature ranged from ambient to 250° C. Suitable mold materials were found to be quartz, heat-resistant glassware, olivine, and zircon. Welding of the alloy can be accomplished using tungsten inert gas process. Tensile strength of the alloy, in the as-cast condition, was found to be 2,000 1b/sq in with an impact strength of less than 1 ft-1b. The coefficient of thermal expansion was determined to be 18.4 x 10-6/° C after heat treatment.

Jan 1, 1977

By J. E. Matta

The Bureau of Mines has developed a tracer gas method for measuring leak-age through permanent mine stoppings. In this method, a temporary brattice is erected in the same entry as the leaking permanent stopping. Leakage was evaluated from concentration measurements of a tracer gas introduced into the space between the stopping and brattice. Stopping leakages ranging from 15 cfm to 265 cfm were simulated in an underground coal mine. Leakage values determined by the new method were within 10 pct of the known values.

Jan 1, 1978

Provide sound battery safety guidelines for mine workers who maintain mobile surface mining equipment. Approach Battery-related accidents account for about 5 percent of all nonfatal disabling injuries in coal and metal nonmetal surface mines. These accidents occur despite the fact that appropriate battery safety technology (maintenance-free batteries, cable removers, fault detectors, hot-jumping systems, etc.) exists. Mine operators are not always aware of the safety measures that could be taken because this safety information is widely scattered in numerous unrelated technical reports, vendor brochures, and journal articles. A literature search of these reports and a review of relevant industry standards, handbooks, and references on battery safety, followed by discussions with mining company and MSHA personnel, provided the Bureau of Mines with the background necessary to develop procedures for proper and safe battery usage. These procedures were condensed and written in nontechnical language to serve as guidelines in assuring battery safety during maintenance of mining equipment.

Jan 1, 1986