Search Documents

By J. Grumer

Nine dust and gaseous inhibitors of propagating coal dust-air flames (lean, stoichiometric, and rich) were evaluated in a newly developed 15-cm-id, 3.6-meter-long instrumented flame duct, under conditions such that wall quenching was virtually absent and the dust concentration was temporally and spacially uniform to within about t5 percent. Listed roughly in order of increasing efficiency, the inhibitors evaluated were rock dust (calcium carbonate), powdered oyster shells (calcium carbonate), Halon 1301 (trifluorobromomethane), Halon 1211 (difluorochlorobromomethane), sodium chloride, Super-K (potassium chloride), regular-grade fire extinguishant powder (sodium bicarbonate), Purple-K (potassium bicarbonate), and Monnex (potassium bicarbonate combined with urea). Experiments were extended to clouds containing 1 and 2 volume-percent of methane. The inhibition of lean, stoichiometric, and rich methane-air flames without coal dust was also examined in a few instances; results agreed with those obtained for coal dust-air flames.

Jan 1, 1971

By G. M. Molinda, J. P. Ulery

Since 1970, abnormally high methane emissions have been observed in eastern sections of the Federal No. 2 Mine operating in the Pittsburgh Coalbed in northern West Virginia. The nature and volume of these emissions indicate a source other than the coalbed. An investigation was undertaken to delineate probable methane sources. Gas well information and stratigraphic correlation of corehole data indicates that a sandstone directly above the main coalbed is an additional source of methane emissions. The sandstone body appears to be an ancient stream channel, infilled with fine-grained sand and organic matter. Coalification of the organic matter produced methane as a byproduct. Additional methane presumably migrated into the sandstone unit from the subjacent coalbeds. The methane became trapped in the porous clasticunit by the surrounding impermeable strata. Mine development near this unit creates a significant pressure gradient, triggering abnormal methane emissions into the mine along naturally occurring fractures. Pre-development methane drainage of the sandstone could be accomplished by completing vertical boreholes along its trend.

Jan 1, 1984

By Martin S. Oudenhoven

This report describes the results of a Bureau of Mines investigation in which the stress concentrations and distributions caused by inclusions in a strained elastic plate were determined, Finite element analyses were made for 168 models containing single inclusions of elliptical, ovaloidal, and rectangular shape. The variables studied included: horizontal-to-vertical loading ratios, (Sh/Sv) of 0,0.33,0.5, and 1.0; width-to-height ratios (w/h), of 0.25, 0.5, 2, and 4; and Young's modulus of inclusion to Young?s modulus of plate ratios (K ratios) of 0.33, 0.5, 2.0, and 5.0. The results show that the theory for elliptical inclusions can accurately predict the average stress along the x and y axes of symmetry for circular, ovaloidal, and rectangular inclusions from the width-to-height and K ratios. The actual inclusion shape was insignificant, suggesting that the average stresses in other inclusions of irregular shape (orebodies) can be estimated with the theory for an elliptical inclusion. An application of this technique to mining problems is presented. The stresses in the elliptical inclusions were uniform throughout the inclusion for all the models studied.

Jan 1, 1972

By Joseph Cervik, J. H. Perkins

The Bureau of Mines has conducted desorption work on fine coal particles at near atmospheric pressure. An apparatus has been developed that uses a capacitance manometer to measure desorption of methane from coal particles up to 2 inches in diameter and pressures up to 1,000 psi. This will make it possible to duplicate the desorption process as it occurs in its natural under- ground environment.

Aug 1, 1970

By R. E. Perry

In connection with a program of coal research at the Southern Experiment Station the Bureau of Mines, in cooperation with the University of Alabama and the various coal operators, conducts washability studies of coal from beds in Alabama and other Southern States in which commercially important deposits occur. One of the main objectives of a washability study is to obtain technically and commercially important data necessary for determining the best methods for preparing and utilizing the Nation's limited reserves of coking coal. Such information is important to conservation because it facilitates selection of preparation methods that will provide maximum yields of coal with low ash and sulfur contents.

Jan 1, 1958

By George R. Schottler

The Bureau of Mines investigated the distribution of uranium and various methods of ore sampling in a uranium deposit typical of those in the Morrison Formation sandstone of the Ambrosia Lake area, Grants mining district, north-western New Mexico. Chemical and radiometric assays of diamond-drill core samples are compared in detail by statistical techniques, and the assay data are correlated with the stratigraphy of the deposit. Conclusions applicable to ore-reserve estimation in geologically similar uranium deposits are drawn.

Jan 1, 1971

By Ann G. Kim

Hydrocarbon gases, primarily methane but also the Ca through Cs paraffins, the Ca and C3 olefins and possibly the C4 and Cs olefins, are byproducts of coal formation. Although it is generally believed that coal formation occurred at temperatures below 200° C, most experimental work on gas formation from coal has been performed at temperatures between 200° and 1,000°C. The objective of this Bureau of Mines experiment was to determine if observable changes in the gases from coal could be produced at temperatures below 200° C in relatively short periods of time. The experiment involved heating coal samples from six coalbeds at constant temperatures and analyzing evolved gases. The composition of the gases at three temperatures was compared. At 35° C, over 99 pet of the gas is methane; at 125° and 150°, methane constitutes approximately half of the hydrocarbon gas. Isobutane and pentane are the predominant higher hydrocarbons at temperatures between 100° and 150° C.

Jan 1, 1974

By Edmund S. Leaver

This information circular is written is response to the marry requests for information on the recovery, or reason for poor recovery, of fine gold by the amalgamation process. Checking Gold Content Experience has shown that in many cases error has been made because the true told content of a particular sample or deposit was not known. Fire assays of representative samples give accurate results and should be considered final in determining the gold content.

Jan 1, 1928

By Ted C. Briggs

Equations for the elastic pressure distortion of the volumes of a Burnett compressibility apparatus are developed and presented in this report for volumes under internal and external applied pressures. An experimental method for the determination of the external pressure distortion coefficients is presented. Young?s modulus and the internal-pressure distortion coefficients are computed from the experimentally determined external-pressure distortion coefficients. The temperature dependence of the pressure distortion coefficients and of Young's modulus is evaluated for the temperature range 0° to 80° C.

Jan 1, 1968

By Thomas J. Fisher, Christopher C. Jobes, Edward F. Fries

This report (Software Safety 2.2) is the third in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended or use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g] and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and non networked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety .• 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meets the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full lifecycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment.—The independent assessment of the Safety File is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • 5.0 Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be don and the guidance is the how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treaty of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. [ ]

Jan 9, 2001

By J. J. Henn

A process is evaluated for recovering metallurgical-grade manganese are from the low-grade manganiferous iron ores of the Cuyuna Range, Minnesota. The process, developed by the Bureau of Mines, employs high-temperature sulfatization of the are to form manganese sulfate and reduction of the are to convert the iron to a magnetic oxide. The roasted ore is water-leached to dissolve the manganese sulfate, which is then separated from the leach residue, is crystallized, and is calcined to produce the manganese product. Iron is recovered from the leach residue by magnetic separation, and is pelletized and calcined to produce byproduct iron ore pellets. The fixed capital cost for a plant yielding a product containing 100 tons of manganese per day is $19.6 million on a mid-1970 basis when the raw are contains 4.84 percent manganese. The estimated operating cost of the plant is $211 per ton of contained manganese. Graphs are included to show the effects of ore cost and varying manganese content of the raw ore on the estimated operating cost.

Jan 1, 1972

By Robert F. Chaiken

A novel approach to eliminating environmental and public safety hazards that are associated with fires in abandoned coal mines and waste banks involves the use of in situ combustion technology developed by the Federal Bureau of Mines to accelerate the burning of the wasted coals in place. This technology would be used under exhaust ventilation control conditions that would allow for total management of the hot gases produced. Combustion stoichiometries would be optimized to minimize unburnt combustibles and to maximize the heat content of the gas products, which will be exhausted at one or more fan locations. When necessary, scrubber systems would be employed to remove air pollutants, such as sulfur dioxide; heat utilization systems (process heat, steam, and electricity) would also be employed to offset operational costs. Ultimately, complete burnout would solve the fire and acid water formation problems of the abandoned coal mine or waste bank. Pertinent technical data for burnout control are derived and discussed in terms of the important material and operational parameters. In general, it is believed feasible to operate a burnout system in an existing abandoned mine or waste bank fire at thermal power levels in the range of 10 to 100 Mw, and at exhaust gas temperatures of 1,000° C (1,830° F).

Jan 1, 1980

By B. R. Mohal, F. F. Aplan, S. Chander

"Dust abatement by water sprays involves the subprocesses of 1) collision between dust particles and water droplets, 2) adhesion of particles to droplets, and 3) engulfment of particles by the droplets. A review of the fundamental aspects of these subprocesses shows that collisions between particles and droplets are determined by aerodynamics and the size and surface charge of the particles and of the droplets. However, the adhesion and engulfment subprocesses depend upon the wetting characteristics of the particles. Although wetting agents (also known as surfactants) have been used as dust suppressants in several investigations, conflicting results are available regarding their effectiveness. In this paper, we show that these results can be explained if the effects of coal rank on surfactant adsorption and wetting characteristics are taken into account.The influence of several nonionic surfactants containing polyethoxy adducts on the wetting behavior of coal is presented. The wetting was determined by a modified Walker Test method, and contact angle measurements. The results show that the wettability of coal depends upon coal rank, structure of the hydrocarbon chain of the surfactant, and the number of ethoxy groups in the molecule.IntroductionDue to the inherent nature of the mining process, a large number of particles are generated, a portion of which becomes airborne to create dust. Dust can be aesthetically and environmentally unacceptable and it can also be explosive. Fine particles in the respirable size range ( < 5 urn) are con-sidered to cause lung diseases, namely, silicosis, pneumoconiosis, etc.(1) Several approaches to reduce dust in mine environments are practiced throughout the mining industry. These include decrease in generation of dust through improvements in mine machinery, ventilation (in which lower dust levels are achieved by dilution of contaminated air with clean air), and dust removal methods. Water sprays are most commonly used to remove dust par-ticles. Recently, scrubbers are reported to have been installed on mining machines to remove dust,(2,3) which also make use of water sprays to reduce dust."

Mar 1, 1989

By M. L. Whisman

The Bureau of Mines developed a radiotracer method for detecting the contribution of selected components and additives to thermally induce deposits of turbine aircraft fuels. Fuels were examined before and after 52 weeks of storage at 130° F. Of particular concern was the influence of aromatic hydrocarbon fuel constituents on thermal-stability quality of jet fuels during storage. A microfuel coker test apparatus was used to thermally stress the test fuels and blends, and the resultant contribution to deposits of selected fuel components, labeled with carbon-14, was determined by radioactive-counting techniques. Ninety-one blends of five test fuels with carbon-14-labeled fuel additives or components were prepared, tested, stored for 52 weeks at 130° F, and reanalyzed for deposit-forming tendency. These additives included two anti-oxidants, a metal deactivator, and a corrosion inhibitor. Of the labeled hydrocarbon fuel systems studied, the greatest reaction was observed in blends containing methyl-and ethyl-substituted indenes. Other aromatic types also showed some contribution to the deposits. Three of the additives showed a marked tendency to degrade and react during storage and thermal stress. A cresol antioxidant, however, barely contributed to deposit formation. Oleic acid interacted with cadmium present in aircraft fuel systems and produced deleterious effects upon the thermal-stability quality of the fuel.

Jan 1, 1971

By Anthony T. Lannacchione, Donald G. Puglio

The Bureau of Mines developed data on the methane content of the Hartshorne coalbed, Haskell and Le Flore Counties, Okla. The methane content is calculated to be between 1.1 and 1.5 trillion cubic feet, based on an estimate of total coal in place of 2.4 to 3.2 billion short tons. Methane increases with depth, but the rate of increase decreases with greater depths. Degasification in advance of mining is recommended for all mines operating at depths greater than 500 feet to reduce hazards and methane explosions, decrease mine ventilation costs, and conserve the natural gas that would be otherwise wasted.

Jan 1, 1979

By Parviz F. Rad

The Bureau of Mines conducted rock-cutting experiments under constant normal force and constant penetration in an effort to correlate laboratory data with those obtained in the field. Both independent and interacting groove spacing regions were studied, and optimum and critical cutter spacings were determined. For the laboratory work, the effects of specific energy, muck weight, groove depth, cutting coefficient, and size distribution of the muck for both independent and interacting grooves were studied. For field operations, forward thrust, torque, advance rate, and muck size distribution were the parameters studied. Satisfactory correlation is obtained between laboratory cutting results and field performance data.

Jan 1, 1974

By G. T. Brow

An experimental method is described for testing diffusion of gases in crude oils at pressures and temperatures up to 3,000 psia and 200° F. A sampling technique was developed to withdraw by constant-pressure mercury displacement about 60 µl of oil from the diffusion cell through any of several 1/2-in vertically spaced capillary tubes and to trap about 4 µl of the oil in a specially designed microsampler. Oil trapped in the microsampler can be completely inserted in the sample inlet of a chromatograph. From analysis in a three-stage chromatograph (GLC), gas concentration in a sample is determined from the ratio of gas peak heights to area of peaks of reference components (hexanes or heptanes) in the oil. A diffusion coefficient is calculated from measured concentration profiles with known equations for diffusion in finite or semi-infinite systems, depending on whether the gas has or has not reached the end of the oil column. Results are given for a test of methane diffusing at 2,560 psia and 160° F in crude oil from the Weber Sandstone reservoir in the Rangely field, Colorado. A constant diffusion coefficient of 3.34 X 10-5 cm2 per sec was obtained which gives a good fit between calculated and experimental profiles determined at six times after start of diffusion. The maximum standard error of gas concentration determinations experienced with this method was ±0.88 ml per ml of gas-free oil.

Jan 1, 1970

By Albert E. Long

Diamond-bit performance and cost data accumulated in core-drilling sandstones reveal significant trends of economic interest. Large-size, AA-Grade drill bort suffered less diamond loss per foot drilled than any other size or grade of diamonds assessed. Detailed analyses of the factors that affect diamond-bit performances -diamond size, diamond quality, bit size, bit type, percentage of core recovered, and physical characteristics of bit matrices -are assessed in the tables, graphs, and discussion. INTRODUCTION Since 1945 the Bureau of Mines has been compiling detailed performance records on diamond bits used in core drilling throughout the United States and Alaska. Analytical reports covering bit performance in various rocks are issued as in-formation on a significant number of bits used in anyone type of rock is accumulated. The first three such reports analyzed bit performance in gneiss,2/ schist,3/ and lime-stone and dolomite.4/ This report evaluates diamond-bit performance in sandstone. Data obtained from 627 bits, which drilled 42,665 feet on 45 different projects, are presented. The geographical distribution of the projects is shown in figure 1.

Jan 1, 1958

By Richard E. Dawes

Physical variables, a principal factor in the economies of mineral production, affect both capital and direct operating costs. By using a revenue-cost system for the framework, the analyses of revenue and cost categories demonstrate the relative importance of groups of physical variables, whether explicitly defined or not, to a lead-zinc mining operation. Physical variables affecting the producer represent about 60 percent of the total system influence as expressed by cost ranking. Other physical variables affect the remaining costs as controlled by the smelter, the transporter, and the landowner. Such resource conservation aspects as mineral losses due to mining method and mineral processing constitute a portion of the total revenue effects of physical variables. The physical variable revenue-cost system presented in this report offers a framework for cost-benefit analysis of mineral related research.

Jan 1, 1969

By W. A. Cole

The sulfur shortage that existed during the Korean conflict stimulated interest in coal measures as possible sources of sulfur. One of the areas brought to the attention of the Bureau of Mines was in Marion County, Iowa, where comparatively high-sulfur coals and other marcasite-bearing strata were known to occur. A Bureau of Mines engineer inspected the marcasite occurrence on December 4, 1954; this prompted further work on the Iowa coals and associated formations as a source of iron sulfides. An investigation of the Iowa high-sulfur coals was undertaken including core drilling, field reconnaissance, and compilation of data pertinent to consideration of the following: 1. Upgrading Iowa coal by mechanical cleaning and the feasibility of recovering sulfur from coal brasses. 2. Possibility of processing the high-sulfur coals by adaptation of methods employed in processing industrial gases to produce sulfur and sulfur products. 3. Possibility of finding concentrations of iron sulfides in associated rock formations in sufficient quantity for economical recovery.

Jan 1, 1957