Search Documents

By Ronald D. Hill, Elmore C. Grim

The United States is richly endowed with mineral resources. However, mineral recovery by its very nature, involves a destructive process, Figures 1 and 2. In the past, mining practices were all too often conducted with the purpose of removing minerals by the simplest and cheapest method possible, without plans for the preservation of land, water, and air, and with too little consideration for the rights of others. A mining company is in business to make a profit, but every company, regardless of the nature of its business, has moral obligations to reduce its undesirable effects on the environment and to safeguard the rights of others. The problem of environmental degradation caused by surface mining is widespread and serious. Minerals in some form occur in each of the 50 States and several States are extensively mined. Data on the acreage disturbed in the United States, by commodity and State are presented in Table 1. Thirty-one States have laws regulating surface mining, (Table 2). Briefly reviewed in Appendix A-1 are the basic provisions of State laws governing surface mining. It can be seen that these laws vary considerably from State to State owing largely to the mining conditions within that State. Of the 24 coal-producing States, only three (Alaska, Arizona, and Utah) do not regulate strip mining. Even the states that are often cited as models of comprehensive regulations still have problems minimizing environmental damages. Uncontrolled surface mining presents a situation as critical to the well-being of the society as any it has ever faced. Many mining activities have imposed huge social costs on the public at large. These costs are long-range and are in the form of stream pollution, floods, landslides, loss of fish and wildlife habitats, unreclaimed land, erosion, and the impairment of natural beauty. In a 1965 Department of Interior study,(1)it was estimated that of the 25,000 miles (1+0,225 kilometers) of contour bench in Appalachia, approximately 1,700 miles (2735 kilometers) are affected by massive landslides. Additionally, 1+800 miles (7723 kilometers) of streams and 29,000 surface acres (11,716 hectares) of impoundments and reservoirs have been seriously affected by coal strip mining operations in the United States.

Jan 1, 1974

By Kenneth J. Miller

The Bureau of Mines conducted an investigation to improve the flotation response of coals that are difficult to wash by froth flotation. A literature survey and experimentation showed that, for the most part, refractory coals can be floated with oily collectors and frothers. Collector reagent consumption can be minimized and the selectivity of the flotation enhanced by assuring adequate, but not prolonged, reagent conditioning. Where flotation selectivity is especially poor, two-stage rougher-cleaner flotation is recommended. It was concluded that a major problem with refractory coals is predicting when they will appear in a flotation circuit so that supplementary flotation collectors can be added. Coal losses due to variation in the floatability of the feed might be reduced if a nonpolar collector such as kerosine or fuel oil is used along with a frother as general coal flotation practice.

Jan 1, 1977

By E. P. Youngman

The mining laws of Russia (Collection of Laws, vol. 7, 1912) are still in force in Latvia. The Free State of Latvia (declared independent on November 8, 1918) is composed chiefly of the Baltic Provinces of the former Russian Empire, which are ethnographically Lettish: The Province of Courland, four districts of the Province of Livonia, and three districts of the Province of Vitebsk. Since the establishment of its independence, Latvia has not felt the need of a special mining law, inasmuch as mining so far has not been found profitable in that country. A supplement to this paper, entitled "Mineral Resources," is a brief summary of the minerals found and utilized in latvia. RIGHTS OF FOREIGNERS A foreign individual is permitted to explore for minerals and to own and operate mines in Latvia on equal terms with Latvians. A foreign corporation is required to establish a branch in Latvia, which shall be subject to the corporation laws of the country. A certain number of the partners or incorporators must be citizens of Latvia.

Nov 1, 1931

By F. Garcia, J. Cervik

Recent advances in the commercial separation of gases using membranes have renewed interest in the possibility of applying this technology to the recovery of methane ( CH4 ) from mining operations . This Bureau of Mines report briefly reviews the history of the development of membranes for gas separation , the theory of how they work , and their application to the separation of methane from air and associated problems . However , methane -air mixtures are difficult to separate with membranes because the pertinent gas couples , 02 - N2 , 02 - CH4 , and N2 -CH4 , have poor separation characteristics , as indicated by their separation factors of about 3 or less . Even if these separation factors were substantially higher , there is doubt that methane could be recovered economically from the low concentrations in mine ventilation exhaust ( 2 vol pct or less ) . The exhaust pressures are not sufficient for adequate separation . The power cost of compressing the methane recovered . these mixtures would far exceed the value of New discoveries could make separation of gob hole methane - air mixtures practical . These mixtures have much higher concentrations of methane (from 30 to 100 vol pct ) ; however , for safety reasons , be limited to gob gas with 60 vol pct CH4 or more .

Jan 1, 1988

By M. R. Geer

The washability examination of a coal establishes the quality of the product that could be prepared by mechanical cleaning, shows how much impurity would have to be eliminated to attain a particular quality of product, indicates what type of cleaning process would be suitable, and tells whether the coal could be cleaned efficiently, The coal-preparation laboratories of the Bureau of Mines make washability examinations of coal for a variety of purposes. Sometimes these examinations are made as an integral part of research conducted on coal-washing problems. Occasionally they are made on coals mined on Government-owned land or on coals destined for use in Government installations. Often they are made on coals from new fields or new beds in existing fields to help establish the characteristics of the Nation's coal reserves. Whatever the original reason for doing the work, the results often are useful later in evaluating deposits or in the design of cleaning plants. Publication of the results of such studies provides for the widest possible usefulness. This report brings together the results of washability examinations made on 1 coal each from Oregon and Idaho, 2 from Wyoming, 5 from Utah, and 11 from Washington. Material of this nature is inherently difficult to summarize. Some of the coals are so clean} despite full-scam mechanical mining, that they could not be improved materially by washing; others present some of the most difficult preparation problems found in the country.

Jan 1, 1961

By McHenry Mosier

Although local conditions at each mining property affect the percentage of increase in drilling speed for a given reduction in gage of bit, the results of drilling tests conducted at the Mount Weather testing adit show such a large advantage in favor of the smaller gages that they should be indicative of the possibilities at most mines. GENERAL DISCUSSION Although it is common knowledge among miners that drilling speed increases with reduction in gage of bit, the large amount o this increase is not so universally realized, A recent Bureau of Mines4/ survey of drilling practices in 28 metal mines showed that the maximum gage of starters is 3 inches and that at 50 percent of the mines starters are 2-1/4 inches or larger, Because this size appears too large for conditions at most mines where abrasion is moderate and where powder distribution permits, the use of smaller bits presents a favorable opportunity for reducing drilling costs.

Jan 1, 1939

By McHenry Mosier

Although local conditions at each mining property affect the percentage of increase in drilling speed for a given reduction in gage of bit, the results of drilling tests conducted at the Mount Weather testing adit show such a large advantage in favor of the smaller gages that they should be indicative of the possibilities at most mines. GENERAL DISCUSSION Although it is common knowledge among miners that drilling speed ill- creases with reduction in gage of bit, the large amount o this increase is not so universally realized, A recent Bureau of Mines4/ survey of drilling practices in 28 metal mines showed that the maximum gage of starters is 3 inches and that at 50 percent of the mines starters are 2-1/4 inches or larger, Because this size appears too large for conditions at most' mines where abrasion is moderate and where powder distribution permits, the use of smaller bits presents a favorable opportunity for reducing drilling costs.

Jan 1, 1939

By Ann G. Kim

The Bureau of Mines investigated factors that influence the formation of methane and other hydrocarbon gases in coal, which is an integral part of the coalification process. Coalification begins with a biogenetic stage in which plant debris decomposes and peat is formed; methane and CO2 are the predominant gases produced during this stage. During the diagenetic stage of coalification hydrogen and the hydrocarbon gases methane, ethane, ethylene, propane, propylene, butene, iso-and normal butane, and pentane are formed by dissociation of the organic material. Methane may also be produced by a secondary reaction of hydrogen with unsaturates or by the reduction of CO2. The gas contained in coalbeds is a mixture of methane, C2 through C5 alkanes, CO2, O2, N2, H2, and He; its heating value is equivalent to that of natural gas. The gas content of coal depends on many variables, but an empirical relationship between adsorptive capacity, rank, and depth has been observed.

Jan 1, 1978

By Homer J. Ballinger

A multiple drill carriage or "jumbo," which is believed to be unique in both design and performance, was constructed and has been in use for the past year at the Bureau of Mines experimental oil-shale mine near Rifle, Colo. This jumbo mounts four long feed percussion drills and is so designed that two men can operate all four drills. Before the jumbo was placed in operation, a minimum of eight man-shifts was required to drill 72 fifteen-foot holes in headings 60 feet wide and 27 feet high. The sane round is now drilled by two men in about 6 hours. Over 500 feet of drilling per man shift is easily and consistently accomplished. Use of the jumbo has resulted in a 75 percent reduction in drilling labor and a substantially lower drilling cost.

Jan 1, 1950

By John Redington

This paper describing the milling practice at the Coniaurum Mine is one of a series of papers on milling methods, practice, and costs prepared in cooperation with an published by the United States Bureau of Mines. The 500-ton will of the Coniaurum Mines (Ltd.) is located at approximately the center of the company's property and a little more than a mile from the town of Schumacher, Ontario. The main shaft through which all the ore is heisted is adjacent to the mill so that the ore hoisted in a 3-ton skip is dumped directly into a 15-ton bin at the crusher.

Jan 1, 1931

By J. Hanslovan, R. H. King

An investigation of the feasibility of shielding low-voltage trailing cables in underground coal mines is described. Both laboratory and under¬ground installation results are presented. The main objective of shielding is to reduce the electrical shock hazard; however, several problems will be encountered by mine operators who install shielded cables. Parameters related to such items as purchasing, splicing, troubleshooting, safety, and reliability are discussed. Some of these problems can be minimized by changes in cable constructions and shuttle-car reeling-device components. Both SH-C and SH-D constructions are considered.

Jan 1, 1979

By Wilder D. Foster

In estimating the hazardous qualities of a dusty atmosphere it is frequently desirable to determine the composition of the air-borne dust. Samples collected from ledges or from the rock itself are likely to be unsatisfactory for this purpose owing to the possibilities of differential disintegration of the rock and of variations in settling rates of the different components of the minerals. It may be necessary, therefore, to collect samples of dust from the air. Samples collected from the air may be analyzed chemically, by X-ray diffraction, and by the petrogrephic microscope. Chemical methods are unsatisfactory owing to the small samples usually available and to the limitations and complexities of present methods. X-ray technique requires expensive apparatus not ordinarily available except in research laboratories. Owing to the simplicity and rapidity of petrographic examination of atmospheric mineral dusts, it was considered worthy of further study.

Jan 1, 1938

By Gerrit V. R. Goodman, Charles D. Taylor, Edward D. Thimons

Future coal mining systems will be able to cut from crosscut to crosscut where advances could exceed 100 ft. However, limitations arise when ventilating such mining systems. In deep advance mining, there would be no workers at the face to advance ventilation tubing or curtain manually. Traditional methods also provide no means for maintaining face ventilation after the miner backs away from the face. U.S. Bureau of Mines research is studying means to provide effective ventilation at cut depths beyond the current limit of 40 ft. Several innovative ventilation schemes are currently being considered. One such method is the use of a jet fan to ventilate a deep cut. A jet fan is simply a freestanding fan using little or no ducting to direct the ventilation flow. Jet fan testing in a 90-ft entry revealed that higher exit velocities and greater penetration depth occurred when various configurations were used to confine and direct the air flow. Additional testing also indicated that 2,200 cfm of fresh air was delivered to the face 90 ft distant when a check curtain was used to limit entrainment around the fan. Without this curtain, this quantity dropped to only 1,000 cfm This testing indicated that a jet fan was capable of providing ventilation to a distant face area. It also highlighted potential problems, such as recirculation at the fan and reentrainment in the jet flow. Despite these potential problems, jet fans may be adequate for ventilating cuts exceeding 40 ft.

Jan 1, 1992

By D. B. Dow

"In the natural-gas Gasoline industry, the methods used in determining the amount of gasoline in natural gas are many and varied; they include the specific-gravity test, laboratory tests involving absorption, charge in volume of the gas or in the absorption medium, absorption in charcoal with subsequent distillation, compression of the gas which results in the condensation of the gasoline, and the absorption of the gasoline vapors in an absorption oil, from which the gasoline is distilled and measured. Each of these various tests has advantages, and disadvantages. It is however, conceded in the industry that the tests in which the gasoline is obtained and measured as such are the more reliable.This paper deals with certain factors which should be considered in making absorption tests using ""mineral seal oil"" as an absorbent; this method of testing is widely used not only in the field, but in control work in absorption gasoline plants where the gasoline content of the intake and discharge gas is determined daily. In control work it is frequently found that the plant produces more gasoline than the tests show, which gives the plant the appearance of making more gasoline than is actually present in the gas treated, or in other words operating at more than one hundred per cent efficiency. Obviously then, the tests as made in these cases are in error, and in hope of correcting some of these variances, the following factors have been studied at the U. S. Bureau of Mines petroleum station at Bartlesville, Oklahoma."

Aug 1, 1920

As part of the U.S. Bureau of Mines (USBM) program to characterize subsidence this combination of software and hardware has been used to remotely monitor overburden response to longwall mining. Background The principle of time domain reflectometry (TDR) is being used by the USBM to monitor strata displacements induced by mining. This capability has been enhanced by the availability of cable testers with serial communication modules that allow users to get TDR records in digital form. Actual field installations involve coaxial cables that arc hundreds of meters long, and the many records obtained when monitoring such long cables on a daily basis motivated development of software to view interactively and compare waveforms and to analyze signature changes. Time domain reflectometry (TDR) was developed in the 1960's as a method to locate discontinuities in coaxial transmission cables. The concept has been extended to measurement of properties of materials into which probes are embedded, such as water content of soil, and evaluation of coaxial cable dielectric behavior. This technique was adapted by the USBM in 1975 for use in checking the movement of rock during underground mining. Coaxial cables are grouted into a rock mass that is expected to cave, and progressive rock movement causes the cable to deform. Consequently, there is a progressive change in cable electrical properties that produces changes in TDR pulse reflection signatures. TDR technology has been advanced by Northwestern University to the point where it is now possible to distinguish shear deformation from tensile deformation, and to quantify rock mass displacements, by analyzing these changes in TDR signatures.

Jan 1, 1993

By R. A. Beall

Homogeneous zirconium-alloy ingots have been cast on a production basis by the consumable-electrode arc-melting process at the Northwest Electrodevelopment Experiment Station, Bureau of Mines, Albany, Oreg. This paper describes the various methods used to introduce alloying materials into the ingot and evaluates 1 each method by the degree of homogeneity of resulting ingots, as determined in tests on sections cut from the ingots. As many as 30 or more ingots, each 6 to 10 inches in diameter and weighing 300 to 500 pounds, were melted, using each method; and, as most of them subsequently were fabricated to strip 0.1 inch thick, the test results are considered to be representative of production practice. Ingot homogeneity has been considered more difficult to achieve in arc-melting practice than by methods where the molten metal is poured into molds and the addition can be stirred into the total mass of metal before casting. Owing to the unique requirements of consumable-electrode arc melting the addition can be made only to that part of the total mass of the ingot that is molten at one time. Observation of the flowlines in 500-pound ingots produced at Albany indicates that the molten pool has a maximum depth about equal to the ingot diameter. The weight of metal molten at one time is, therefore, not over 100 pounds. Characteristically, the arc-melting process is conducive to segregation, which can be overcome, at least partly, by adding the alloy constituents almost continuously during casting.

Jan 1, 1956

By C. Özgen Karacan

Methane emissions from a longwall ventilation system are an important indicator of how much methane a particular mine is producing and how much air should be provided to keep the methane levels under statutory limits. Knowing the amount of ventilation methane emission is also important for environmental considerations and for identifying opportunities to capture and utilize the methane for energy production. Prediction of methane emissions before mining is difficult since it depends on a number of geological, geographical, and operational factors. This study proposes a principle component analysis (PCA) and artificial neural network (ANN)-based approach to predict the ventilation methane emission rates of U.S. longwall mines. Ventilation emission data obtained from 63 longwall mines in 10 states for the years between 1985 and 2005 were combined with corresponding coalbed properties, geographical information, and longwall operation parameters. The compiled database resulted in 17 parameters that potentially impacted emissions. PCA was used to determine those variables that most influenced ventilation emissions and were considered for further predictive modeling using ANN. Different combinations of variables in the data set and network structures were used for network training and testing to achieve minimum mean square errors and high correlations between measurements and predictions. The resultant ANN model using nine main input variables was superior to multilinear and second-order non-linear models for predicting the new data. The ANN model predicted methane emissions with high accuracy. It is concluded that the model can be used as a predictive tool since it includes those factors that influence longwall ventilation emission rates.

By D. J. Parker

Du.ring the past two years a number of oases of successful first-aid treatn . .)nt have been reported by or through the employees of the O. s. Bureau of -anes safety cars and stations. Among such cases are the following: At Benbush, w. Va., a boy or 16 years of age who ba.d just started to work in the mines was trained in first-aid by the crew of Bureau of Mines car 8. The local rr.ine superintendent afterwards reported tba.t a few dS¥s later this boy, Melvin Hollingsworht, found droming in a spring a. baby about three years old who bad wandered away fron.. har.e alone. The boy rescued the baby and perf'oxmed artificial re­suscitation upon it, thu.s saving the child's life. The Schaefer method of resuscitation bad bean ta"Ugbt the boy as a routine art of the regular first-aid course.

May 1, 1922

By T. Bieniawski

"INTRODUCTION The Congress theme ""Improvement of Mine Productivity and Overall Economics by Modern Technology"" is probably beat: addressed by the subtheme allocated to this Plenary Session. It is appropriate that .Theme 1 emphasizes the simple point that effective use of geotechnical information is the key to improving mine productivity. In essence, this means that: (1) geological and geomechanics, (rock mechanics) data must be collected in sufficient quantity and of high quality; (ii) data interpretation must be performed specifically for purposes of engineering design; (iii) innovative design approaches should be used to bring about Improvements in productivity and safety.While, each of these three aspects .may: seem obvious to any mining engineer it is a fact that the above sequence is seldom followed and as a result, mining engineering not infrequently lags, behind other branches of engineering when it comes to design creativity, efficiency and safety.. . After all, mining is still-one of the most hazardous occupations and we are gathered here to discuss, at the highest world professional forum, how to use more effectively the modern technology. This however, does not mean that mining engineers are less capable than other engineers or that their achievements are any lesser; far from it! Mining engineers are the cream of the engineering society on whose efforts depends the welfare of mankind. Moreover, they have produced minerals and coal evergrowing quantities against evergrowing difficulties. Yet, we must and can become even better because we are not making full use of the modern technology and rock mechanics knowledge already at our disposal, and. we are not being innovative enough to the full extent of .our capabilities."

Jan 1, 1989

By Gregory J. Chekan

As part of the initial investigation and validation of a new boundary-element formulation for stress modeling in coal mines, the underground stresses and displacements at two multiple-seam coal mines with unique stress problems were modeled and predicted. The new program, LAMODEL, calculates stresses and displacements at the seam level and at requested locations in the overburden or at the surface. Both linear elastic and nonlinear seam materials can be used, and surface effects, multiple seams, and multiple mining steps can be simulated. In order to most efficiently use LAMODEL for accurate stress prediction, the program is first calibrated to the site-specific geomechanics based on previously observed stress conditions at the mine. For this calibration process, a previously mined area is "stress mapped" by quantifying the observed pillar and strata behavior using a numerical rating system. Then, the site-specific mechanical properties in the model are adjusted to provide the best correlation between the predicted stresses and the observed underground stress rating. Once calibrated, the model is then used to predict future stress problems ahead of mining. At the two case study mines, the calibrated models showed good correlation with the observed stresses and also accurately predicted upcoming high stress areas for preventive action by the mines.

Jan 5, 1999