Search Documents

By E. P. Youngman

The law of June 5, 1911, suplements and amends the Laws of April 21, 1810 (the basic law) and May 2, 1837. The Royal Decree of September 15, 1919, coordinates the provisions of the Law of June 5, 1911, with those of the Laws of April 21, 1810, of May 2, 1837, and of July 8, 1865, that have remained in force, as well as with certain articles of the Law of September 1, 1913, which revisad the system of taxation. The revised code has been brought together in one volume.3 All citations in this abstract refer to the coordinating Royal Decree of September 15, 1919, unless it is otherwise specifically indicated.

May 1, 1930

By M. J. Brevoort

Research work in the Bureau of Mines cryogenic laboratory requires the use of high-sensitivity galvanometers of the d'Arsonval type in a building that is subject to unusually severe vibrations. A modified form of the galvanometer suspension described by Julius3 has damped the vibrations so successfully that a short note concerning it is thought to be desirable, The laboratory is on the site of the Amarillo helium plant near a building that houses gas engines of from 180 to 250 hp., driving compressors and electric generators. The distances from the galvanometers to the individual engines range from about 80 to 180 feet. The subsoil, consisting of black clay loam, transmits the impulses without much damping. The usual methods of protecting galvanometers from vibration were tried and proved fruitless. A Julius suspension purchased on the market was carefully installed in the hope that it would overcome the difficulty, but the conditions were too severe even for this elaborate arrangement. Several mudifications of the original Julius suspension, which were then introduced, resulted in almost complete elimination of all vibrational effects.

Jan 1, 1931

By M. J. Brevoort

Research work in the Bureau of Mines cryogenic laboratory requires the use of high-sensitivity galvanometers of the d'Arsonval type in a building that is subject to unusually severe vibrations. A modified form of the galvanometer suspension described by Julius' has damped the vibrations so successfully that a short note concerning it is thought to be desirable. The laboratory is on the site of the Amarillo helium plant near a building that houses gas engines of from 180 to 250 hp driving compressors and electric generators. The distances from the galvanometers to the individual engines range from about 80 to 180 feet. The subsoil, consisting of black clay loam, transmits the impulses without much damping. The usual methods of protecting galvanometers from vibration were tried and proved fruitless. A Julius suspension purchased on the market was carefully installed in the hope that it would overcome the difficulty, but the conditions were too severe even for this elaborate arrangement. Several modifications of the original Julius suspension, which were then introduced, resulted in almost complete elimination of all vibrational effects. These modifications were suggested by careful study of the original idea embraced in the Julius construction. They were designed to give further constraint to motion in any direction other than that parallel to a line from the point of support through the center of gravity of the suspension, This was accomplished by making the suspended frame more rigid and by improving the means of adjusting each of the supporting wires to the same degree, thereby transmitting any impulse symmetrically through the three wires. The result was a suspension that is more effective, particularly for severe vibration, than the form described by Julius; also, it is believed to have advantages in stability, simplicity, and ease of adjustment over the few suspensions for this type of service that the author has found described in the literature.

Jan 1, 1931

By R. V. Ramani, V. T. Burgos, J. A. McClay

The data for Test I describes an underground bituminous coal mine operation in a 48 inch seam, with an estimated production rate of 1,056,000 tons per year. The system includes four continuous mining sections, conveyor belt haulage, and a rail network for supply and personnel transportation. This section illustrates the input data sequence and the various report formats which may be selected for the printing of results. As explained earlier, at the present time, the elements of the Cost Data Library must be read in with the regular data input. Thus, in the input data listing, immediately following the required user input, are cards which contain the inputs of the cost library. Examination of the cost reports indicate the absence of cost values for some categories for which the system would normally be expected to incur costs. This situation has arisen due to the format of the cost data provided in the U. S. Bureau of Mines reports. An example of this is the charge of $20/ton for brattice cloth while no charge is indicated for stoppings. The test report data provided a single figure for ventilation cost without a supplemental breakdown. Thus the cost indicated for brattice cloth is actually the total ventilation cost. These explanations hold true for the data input and output for Test II, Appendix III.

Jan 1, 1975

By James P. Rider, Jeanne A. Zimmer, Andrew B. Cecala, Robert J. Timko, Earle H. Andrews

Many different types of structures and materials have been used to build mineral processing facilities over the past few decades. Although the structure type and building material were not viewed as significant factors affecting the health of employees in these facilities when they were built, the National Institute for Occupational Safety and Health performed an evaluation to determine to what extent building types could impact respirable dust and noise levels. This report discusses the evaluation of three different types of product sizing silica sand structures: a masonry design, a steel-sided design, and an open structure design. The data obtained in this study indicate that the open structure design (no walls) was superior from both a dust and noise (health) standpoint compared to the other two structures. The open structure design should also be beneficial from a cost standpoint because of lower material and construction costs. Companies and design engineers should consider this open design when building new mineral processing facilities in climates where it could be applicable. Some companies may also want to consider modifying existing structures with a more open design to further reduce dust and noise levels. As the trend continues in lowering allowable dust levels for federal health standards in the U.S. mining industry, the open structure design may be an approach for some companies to consider for their operations.

Jan 11, 2006

By T. M. Klemetti, G. M. Molinda, D. M. Pappas

Some of the most difficult coal mine roof in the U.S. can be found in the Illinois Basin. Factors contributing to the high roof fall rate include: weak moisture-sensitive roof rock, high horizontal stress, and limited longwall mining. The depth of cover ranges from 90-1,000 ft and roof damage from horizontal stress can be severe. Moisture sensitive-roof rock is common above the Springfield-Harrisburg Herrin #5 and #6 seams in the Illinois Basin, and contributes to roof skin deterioration. The roof fall rate increases significantly in the humid summer months. The National Institute for Occupational Safety and Health (NIOSH) has shown, using lab and field studies, that highly moisture-sensitive roof rock can be directly correlated to poor roof conditions. Controlling the skin is the key to reducing rock fall injuries, and roof screening is, by far, the best remedy. Illinois Basin coal operators have been successful in reducing the number of rock fall injuries in recent years. NIOSH has documented best practices for screen installation which has resulted in safe, efficient operations. Other solutions to skin failure include: the use of denser five bolts per row patterns to reduce spans between bolts, systematic supplemental support in intersections, straps and large pans protecting operators, and air conditioning to remove moisture from the intake air.

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are tables that show the principal nonfuel mineral commodities exported from and imported into the United States, and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines. Because of inadequacies in the statistics available, some series deviate from the foregoing definition. For gold, silver, copper, lead, zinc, and tin, the quantities are recorded on a mine basis (as the recoverable content of ore sold or treated). However, the values assigned to these quantities are based on the average selling price of refined metal, not the mine value. Mercury is measured as recovered metal and valued at the average New York price for the metal.

Jan 1, 1981

By J. I. Paige

The Bureau of Mines, U.S. Department of the Interior, conducts research on methods to minimize the requirements for mineral raw materials through conservation, substitution, and increased minerals and metals recovery from primary and secondary domestic resources. To further this goal, prior Bureau research had devised a pyrometallurgical technique (RI 8211) to recover metallic iron and copper from molten copper smelting furnace slags by carbothermic reduction. As a continuation of this Bureau research on the carbon injection technique, reverberatory and electric furnace slags were treated in an 800-kva electric arc furnace by simultaneously top feeding the slag and injecting coke breeze into the bottom of the molten bath. Results of the tests show that 76 to 89 pct of the copper and up to 48 pct of the iron contained in the smelting furnace slag were recovered in a metallic phase, while 56 to 82 pct of the carbon injected into the sys-tem was utilized as the reductant. Laboratory evaluation has shown that the metal product, which contains 86.9 to 95.0 wt-pct iron and 1.3 to 4.1 wt-pct copper, will be a satisfactory medium for recovering copper by cementation. The expected energy consumption for the process is 110 kwhr per ton of molten slag treated and 520 kwhr per ton of solid material charged.

Jan 1, 1982

Provide coal mine shafts/slopes with an optimum coal mine shaft fire and smoke protection system composed of reasonably-priced, reliable hardware. Approach Accident and injury data indicate that a relatively low percentage (5%) of underground coal mine fires occur in shafts or slopes. Nevertheless, shaft or slope fires are extremely serious because they block critical escape routes for miners. That also can happen when combustion products resulting from fires in other mine areas contaminate shahs and slopes. Seeking the optimum configuration for a shaft/slope fire and smoke protection systems, the Bureau of Mines gathered data on the performance of existing fire detection devices and signal telemetry systems In several mines, and analyzed the generic protection needs of the U.S. underground coal mining industry. The optimum system developed by the Bureau provided an adequate number of detectors, a wide area of coverage, and an extensive data acquisition, analysis, display, and storage capability. This system. recommended for fabrication and in-mine testing, consisted of a microcomputer-controlled master panel located in the test mine's slope hoist room, and four remote units. Two of the remote units were placed on the surface atop upcast ventilation shafts, a third was situated underground near the slope bottom, and a fourth was installed at the slope top in intake air.

Jan 1, 1986

By Harry Dobroski, Larry G. Stolarczyk

Theoretical and experimental research sponsored by the U.S. Bureau of Mines shows that medium frequency (MF) electromagnetic (EM) signals propagate great distances in an underground environment such as a tunnel or mine. This propagation is enhanced by different mechanisms associated with the geology, and with the existence of metallic conductors in the entryways. In stratified geologies, a transverse electromagnetic (TEM) mode of signal propagation is possible if a low conducting layer is bounded above and below by higher conducting layers. In general, the difference in conductivities must be at least several orders of magnitude. Such geological waveguide conditions often exist in underground mines. Propagation via the waveguide effect is known as the "seam mode" of propagation. Another mode of propagation, the "tunnel mode," exists in underground entries with electrical conductors such as power cables, metal pipes, and phone lines. A monofilar mode of propagation exists when signals are impressed upon conductors and return via the surrounding rock. A bifilar mode of propagation exists when all signals exist only on local conductors. In a given location there is a combination of monofilar and bifilar modes that make possible an interaction between the conductors and a transmitting device in a tunnel or entryway. Signals can be impressed on or received from local conductors via magnetic dipole antennas (loops) or line couplers.

By Adam K. Smith

Over-exposure to noise remains a widespread, serious health hazard in the U.S. mining industry despite 25 years of regulation. Most other categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. In order to reduce cases of Noise Induced Hearing Loss (NIHL) in the mining industry, retrofit acoustic treatments and controls are being developed to subdue noise at the source. The Mine Safety and Health Administration (MSHA) coal noise sample data collected from 2000 to 2005 has determined that continuous mining machines rank first among all mining equipment whose operators exceed 100% noise dosage. The continuous mining machine conveyor, used to move coal from the cutting face to the rear of the machine, has been identified as a dominant noise source. A dual sprocket conveyor chain was tested as a potential solution. Sound power level measurements conducted at the Pittsburgh Research Laboratory (PRL) accredited reverberation chamber showed a 3 dB reduction in the A-weighted sound power level when the dual sprocket chain was implemented. Underground results show an 8-hour Time Weighted Average (TWA8 hrs) reduction a 3 dB for continuous mining machine operators. Utilizing this newly developed noise control, along with previously proven controls, provides continuous mining machine operators an opportunity to be within the MSHA-Permissible Exposure Limit (MSHA-PEL).

Jan 1, 2009

Provide the technology to remotely control a thin¬-seam continuous mining machine from a safe location hundreds of feet outby the working face in an underground room-and-pillar mine. Background and Approach Hard-wired or radio remote control of continuous mining machine has been commercially available since the early 1970's. This type of remote control, in low and high coal seams, situates the machine operator offboard, but within direct view of the underground coal face, Although positioned under supported roof, the operator can still be exposed to face area hazards that include roof-rib falls, dust, methane explosions, and equipment congestion. The U.S. Bureau of Mines approach has been to put the operator into a protected compartment at a location away from the working face. Since 1979, the Bureau has investigated innovative methods to better protect face area workers in under¬ground room-and-pillar mines. In 1989, the Bureau demonstrated an offboard, computer-based remote con¬trol system in a West Virginia highwall mining operation that stationed the operator hundreds of feet away from the working face. In late 1992, much of this technology, plus improvements, Was used to demonstrate, on the surface, how a thin-scam continuous mining machine could be remotely controlled 200 feet from the machine in a 36-inch working height.

Jan 1, 1992

By T. H. Jeffers

Significant amounts of cobalt, a strategic and critical metal, are present in readily accessible spent copper leach solutions. For example, recovery of cobalt at two major u.S. copper operations could produce about 1,300,000 lb Co annually, about 13 pct of domestic consumption. However, techniques such as solvent extraction and precipitation have not proven cost effective in separating and recovering the cobalt from these low-grade domestic sources. The Bureau of Mines has devised a procedure using a chelating ion-exchange resin to extract cobalt from a pH 3.0 copper leach solution containing 30 mg/L Co. Cyclic tests in 4-ft-high by 1-in-diam columns gave an average cobalt extraction of 95 pct when 65 bed volumes of solu-tion were processed at a flow rate of 4 gpm/ft2 of resin area. After an impurity scrub, eluates contained, in grams per liter, 0.4 Co, 0.2 Ni, <0.001 Cu, 1.3 Fe, 2.8 Zn, and 0.008 AI. Solvent extraction procedures to remove impurities, reject nickel, and concentrate cobalt produced a cobalt sulfate solution containing 80 g/L Co, 0.05 g/L Ni, and not more than 1 mg/L Cu, Fe, Zn, or AI. Based on data from commercial electro-winning operations, this solution appears suitable for production of metallic cobalt.

Jan 1, 1985

By E. J. Gleim

During the past 10 years the Bureau of Mines has had a broad experience in the tasting and inspection of electric motors for gaol-cutting machines, cowl drills, storage-battery locomotives and other equipment Which is used in mines where explosive mixtures of methane and air may be encountered. From this experience the Bureau&apos;s engineers have reached the conclusion that the most satisfactory method of protecting a motor so as to prevent any sparks resulting from rough commutator, loose contacts or short-circuits in it, from igniting he surrounding atmosphere, is to totally inclose the motor with a substantial casing; having flanged joints. These joints should be metal-to-metal contact so that the shortest path from the interior to the exterior Of the casing is not less than one inch in length. On account of this experience with mining machinery, the Bureau has been asked whether an equal or loss degree of protection would be sufficient for motors for service in or about places such as refineries, gasoline filling stations, cleaning establishments and pumping stations, or in any place where there is liklihood of explosive mixtures of gasoline or naphtha vapors and air accumulating.

Jan 1, 1922

Determine the appropriate spacing and alarm levels for carbon monoxide and smoke sensors used for fire detection in underground coal mine conveyor belt entries. Background Fire represents one of the most severe hazards in underground coal mines. Early-warning fire detection in underground coal mines is essential to successfully implement and execute evacuation and control measures. Both carbon monoxide (CO) and smoke sensors have the ability to provide reliable early-warning capability, provided that they are spaced properly and set at the appropriate alarm levels. The U.S. Bureau of Mines conducted a series of large-scale experiments where a small coal fire was used to ignite a conveyor belt at air velocities of 0.76 to 6.1 m/s. The test configuration was purposely designed to model a worst-case fire scenario for fires that develop within conveyor belt entries in underground coal mines. During the tests, CO and smoke levels were continuously measured to determine alarm times and alarm levels as the fire intensity progressed. The data from these tests indicated that for a given sensor spacing, the time to reach a preset alarm threshold depends upon the belt entry air velocity and cross-sectional area. Analysis of this data resulted in the equations and nomographs for CO and smoke sensor spacing, and alarm levels contained in Bureau of Mines RI 9380, "Fire Detection for Conveyor Belt Entries."

Jan 1, 1993

By Charles L. Kimbell

Tables 16 through 19 continue the series of providing the world merchant fleet distribution by type of vessel and the ranking of the major fleets by country of registry. Table 20 this year provides a summary of the world&apos;s liquid gas carrier fleet. These vessels are included in the totals given for the world&apos;s tanker fleet, but gives a breakdown demonstrating the growth of the importance of natural gas in the world&apos;s energy commodity consumption. Panama and Suez Canals Tables 21 and 22 provide the latest available information on the transit of mineral commodities through the Panama Canal, by number of vessels, direction, and the commodities transported. Although the number of vessels transiting the Panama Canal dropped slightly (0.5%) between 1989 and 1990, the total amount of cargo moved rose by 3.6% and the amount of mineral commodities moved rose by 7.2%.

Jan 1, 1993

By J. B. Gayle

Numerous investigators have studied the addition of inert4 substances to coking blends. Generally, the results have yielded trends applicable only to the particular coals and inerts studied. Recently, somewhat more general results were obtained for cokes produced from blends containing added inerts, using the sole-heated oven. The present investigation represents an extension of this work to include a wider range of inerts and to determine the applicability of the various conclusions to cokes produced with the Tuscaloosa oven. The results indicated that an increase in dry-coal charge density of 1 pound per cubic foot (p.c.f.) caused a corresponding change in the hardness (1/4-inch tumbler index) of Tuscaloosa oven cokes of 0.9 percentage points. This value compares favorably with the value of 0.7 determined previously for the sole-heated oven and Bureau of Mines-American Gas Association (BM-AGA) retort.

Jan 1, 1961

By Robert P. Vinson, Fred N. Kissell, Edward D. Thimons

The Bureau of Mines investigated the presence and extent of methane accumulations in mine roof cavities using a full-scale mine model. Methane was released at a constant rate into the roof of a cavity built onto a 700-ft wind tunnel. Two box-shaped roof cavities were used in the study: one had a volume of 114.7 cu ft; and the other had a volume of 57.3 cu ft. Methane concentration was measured at 28 sampling points in the cavities using 21 different combinations of gas emission rates and air velocities. Brattice hung in the cavity helped reduce methane concentrations without auxiliary ventilation. It was also found that the effective ventilation rate increased by a factor of 40 in the large cavity and by a factor of 20 in the small cavity when air velocity was increased from 100 to 600 fpm.

Jan 1, 1978

By D. J. Parker

The oft-repeated expression that the taproot of safety lies in the attitude of the management toward accident-prevention work is indisputable and has become almost an axiom. Trite and somewhat timeworn though the statement may be, it is nevertheless true that the supervisory force must earnestly support a policy of safety and maintain at all times a con¬ siderate regard for the welfare of the employee if that high degree of cooperation of the employee, so vital to the successful prosecution of any safety program, is to be expected. The responsibility for preventing accidents rests upon the management, and in the case of the Spring Canyon Coal Co. such responsibility is recognized and accepted with little or no reservation. This company, aside from the humanitarian aspects involved, believes that safety is good business and not a matter to be treated passively or in a perfunctory manner. The problems with respect to safety that have been met and wholly or partly solved can best be appreciated when some of the natural conditions, adverse and otherwise, existing at this operation are taken into consideration. Mine 1 is about 1 mile north of the town of Spring Canyon, Carbon County, Utah, and is served by both the Denver & Rio Grande Western and Utah Coal Route railways. During the year 1931 the mine produced 312,397 tons, approximately 10 per cent being derived from pillar workings. The normal daily output during the summer months is about 2,000 tons, and during the peak of production in the winter season the daily production varies from 2,500 to 3,000 tons. The number of miners varies from 87 in summer to 220 in winter, and the day men vary in number from 66 in the winter to 45 in the summer; 12 company men are employed the year around. The officers of the company are J. B. Smith, president, San Francisco, California; T. R. Stockett, general manager, Salt Lake City; and G. A. Murphy, superintendent, David Brown, assistant superintendent, and John Sullivan, mine foreman, all of Spring Canyon, Utah.

Dec 1, 1932

Montana&apos;s coal reserves are estimated to be more than 120 billion tons, 24.6 percent of U.S. reserves. Montana&apos;s reserves are the largest in the nation. Coal fields are located throughout the state, primarily east of the Continental Divide. Three of the state&apos;s 17 coal fields have producing mines. Coal resources range from lignite to high volatile bituminous; however, most of the coal currently mined is subbituminous. Although Lewis and Clark mentioned the presence of coal along the banks of the Missouri River in Montana in 1805, the first major mine was not opened until 1867, at Chestnut, Montana, near Bozeman. The mine at Chestnut served Fort Ellis until the mine was bought by the Northern Pacific Railroad in 1883. By 1900, underground coal mining had developed throughout the state, primarily to supply fuel to the railroads. In the 1920s, large-scale surface mining began in Colstrip to fuel railroad steam engines. Currently, all coal mined in the state is produced from surface mines. The Office of Surface Mining granted the Montana regulatory program conditional approval April 1, 1980, followed by final approval February 1 1,1982. Montana&apos;s Abandoned Mine Lands Program was approved November24,1980, and its emergency program was approved August 18, 1983. A Federal Lands Cooperative Agreement was approved May 8, 1981.

Jan 1, 1992