Search Documents

By Nicholas Kyriazi

A performance comparison of 14 rescue breathing apparatus was undertaken as an assessment of past and present worldwide technology. Rescue breathing apparatus are self-contained, closed-circuit breathing apparatus used for entry into areas having atmospheres that are immediately dangerous to life and health. Apparatus tested were the Biomarine BioPak 45, 60, and 240; the Draeger BG 4 and BG-174A; the Litton LITPAC II; the MSA Custom 4500 II Air Mask, Chemox, and McCaa; the Sabre Selected Elevated Flow Apparatus (SEFA); the Scott Rescue-Pak; the Siebe Gorman Aerorlox and Proto Ten; and the SurvivairLP-120. The apparatus were tested on an automated breathing and metabolic simulator at the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH). Physiological parameters monitored during the testing were average inhaled CO2 and O2, minimum inhaled CO2, inhaled wet-and dry-bulb temperatures, and peak inhalation and exhalation breathing pressures. The metabolic demand on the apparatus was 1.35 L O2/min for most of the test with two 5-min intervals of 2.5 L O2/min, the first beginning 10 min into the test and the second beginning 10 min before the end of the rated duration of the apparatus. Results presented include apparatus service life and test-averages of monitored physiological parameters. Schematic drawings and photographs of the apparatus are also included. The Draeger BG-174A and BG 4 had the highest durations—295 and 291 min, respectively. The BG 4 hadthe lowest minimum inhaled CO2 levels, attesting to the effectiveness of its CO2-absorbent canister. The SabreSEFA had the lowest average inhaled CO2 levels, due mostly to the apparently low-dead-space mask andnose cup. The MSA Air Mask, the only open-circuit device tested, had the lowest wet- and dry-bulb temperatures, with the liquid-O2-source Siebe Gorman Aerorlox having the next lowest temperatures. The only apparatus with a CO2-absorbent not in a packed-bed design, the BG-174A, had the lowest exhalation pressures. The BG 4 had the highest level of positive pressure, with the Biomarine BioPak 60, Survivair LP-120, SEFA, and Litton LITPAC II nearly as high. The BG 4 had the lowest pressure swing, with the SEFA a close second.

Jan 10, 1999

By Merle Randall

Application of a new chemical spray in a mercury mine in which ore rich in native metal was causing salivation among the miners has given such favorable results that it is believed the process will be useful in other mines and perhaps in some plants where similar conditions exist. The process was originated by Merle Randall, professor of chemistry at the University of California. GENERAL PROBLEM The presence of native quicksilver in mines from which the metal is produced has long been a source of trouble and danger to the workers. Men have been sickened and some of them have been disabled by exposure to the vapors present (even in workings that were well-ventilated by ordinary standards) and to contact with dust, dirt, and moisture with which the finely divided quicksilver was mixed. Where the ore was rich and this exposure was considerable men were able to work only a few days or weeks; where the exposure was less they were weakened and subject to ailments often attributed to other causes.

Jan 1, 1942

By D. Harrington

The desirability of efficient control of air currents, and the necessity of supplying metal-mine workers with better and safer working conditions, has created an active interest in metal-mine ventilation, especially in recent years. This paper discusses the subject both with regard to efficiency and economy, as well as safety and health. It is based on personal observations of the writer from over four year's study of metal mines in six States, in which more than 50 mines were visited. Many of these were studied in detail; in all several thousand working places were examined, and readings taken relative to ventilation run into the tens of thousands.Object of ventilating metal mines:Whereas in coal mines ventilation is generally regarded as essential, in many metal mines, especially shallow ones, the operators pay little attention to ventilation, or ignore it altogether. Recent shortage of labor, and numerous accidents to which State compensation laws have directed attention, are causing metal-mine operators to regard ventilation more seriously, especially in deep, large mines.There is, in fact, greater necessity for adequate ventilation of metal mines than of coal mines. The latter require air currents to remove explosive gases and the fumes of explosives, but metal mines, in addition to the need of removing fumes of explosives, and occasionally explosive gases, frequently have need of removing dusts dangerous to health, reduction of high temperatures and high humidity, and removal of inert but unhealthful gases like CO2 and nitrugen. The generally accepted superior healthfulness of coal miners as compared with metal miners, is probably due in large part to the better air circulation in working places of coal mines.

Jun 1, 1920

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States, and that compare world and U.S. mineral production. Except for the mineral fuel commodities, the detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. In October 1977, responsibility for the collection of data on mineral fuels-coal, petroleum, natural gas, and natural gas liquids-was transferred to the newly created Department of Energy. Although chapters covering these commodities will no longer appear in Volume I of the Minerals Yearbook, quantity and value data have been included in most of these summary tables to maintain statistical consistency in State and national value of overall crude mineral output. This shift in responsibility has also resulted in changes to the composition of the "Nonmetals? and "Mineral Fuels" groups in table 1 and table 2. The commodities-asphalt and related bitumens (natural), carbon dioxide (natural), helium, and peat-have been removed from the ?Mineral Fuels" group, and are now included under the "Nonmetals" group. There has been no change in the components of the "Metals" group.

Jan 1, 1981

By Timothy M. Barton

The U.S. Bureau of Mines is conducting research to assess the effectiveness of different chain pillar designs in maintaining gate entry stability. A particular concern is ground control for deep-cover 1ongwalls located at depths in excess of 1,000 ft. The study described in this report was performed in two experimental sections in one longwall headgate section which contained three different pillar designs. Two of the designs used conventional abutment pillars, while the third was a total-yielding pillar system. Both of the test areas were located under 1,800 ft of cover. The purpose of this study was to evaluate the effectiveness of these three pillar designs for gate road stability. As the longwall mined passed the test areas, Bureau engineers monitored entry convergence, roof sag, and changes in roof quality. The study indicated that the all-yield system performed nearly as well as the better of the two abutment pillar systems; but all of the three designs would have failed to provide acceptable stability for second panel mining without considerable artificial support.

Jan 1, 1989

By G. L. Oldright, Virgil Miller

"INTRODUCTION The first ten papers of the series on smelting in the lead blast furnace described the operation at the custom smelter of the International Smelting Co., Tooele, Utah, and at the plant of the Bunker Hill Smelting Co., Kellogg, Idaho, which handled a very rich lead concentrate. These previous papers may be considered a picture of the traditional lead smelter treating custom ores and of the smelter that will treat the type of product likely to be made in the future - lead concentrates of an increasingly rich grade.The great plant at Trail is of special interest to those smelting lead products containing much zinc and faced with the necessity of transforming all of their byproducts into commodities which may be sold profitably. The plant is equipped to produce electrolytic zinc, lead, copper, silver, bismuth, and cadmium. Part of the sulphur evolved from treating the ores is converted into sulphuric acid. Complete fertilizers for agricultural purposes are also produced.The smelter of lead ores has long considered that zinc is one of the most difficult ingredients that he has to handle. Even with the gretat improvement in flotation practice today, the residues from electrolytic zinc plants leaching zinc concentrates must still be smelted for their lead content. Of the total gangue material not separated from the lead concentrate sent to the smelter, zinc is still one of the most notable in percentage. The most successful way of coordinating the over-all operations of a concentrator, an electrolytic zinc plant, and a smelter provided with a plant for re-treating the blast-furnace slag for its lead and zinc content must be of interest to many treating complex ores.ACKNOWLEDGMENTThe data in this paper were collected in cooperation with the Consolidated Mining & Smelting Co. of Canada, Limited, and its entire technical staff. Detailed acknowledgments of assistance received are given in the papers from which this one is briefed."

Sep 1, 1934

By H. Dolezal

An investigation was made on the use of magnesium for the direct reduction of rutile to make low-cost, offgrade titanium which could be upgraded to an acceptable grade of metal by electrorefining. Reductions made with charges containing magnesium chloride under hydrogen yielded products with oxygen con-tests close to the theoretical equilibrium composition. Two reduction products were made from rutile for use in electrorefining amenability tests: (1) a product from reduction in an inert atmosphere which contained 88.9 percent titanium and 4.42 percent oxygen, and (2) a product from reduction in a hydro-gen atmosphere which contained 92.5 percent titanium and 2.40 percent oxygen. Reduction products obtained under both of these conditions were amenable to electrorefining.

Jan 1, 1965

By A. B. Hooker

All State mining laws require that flame safety lamps be used in gassy mines; the laws of some States require that safety lamps be kept for emergencies at every coal mine, whether gassy or nongassy. The use of the flame safety lamp has been widespread because it is the only defice readily available for detecting both the presence of methane and deficiency of oxygen. This paper reports the results of an investigation by the Electrical Section, in cooperation with the Gas Section, of the Pittsburgh Experiment Sta¬tion relative to the behavior of permissible flame safety lamps in mine atmospheres deficient in oxygen and the effects of methane5 on the detection of Oxygen deficiency.

Jan 1, 1937

By A. B. Hooker

All state mining laws require that flame safety lamps be used in gassy mines; the laws of some States require that safety lamps be kept for emergencies at every coal mine, whether gassy or nongassy. The use of the flame safety lamp has been widespread because it is the only defice readily available for detecting both the presence of methane and deficiency of oxygen. This paper reports the results of an investigation by the Electrical Section, in cooperation with the Gas Section, of the Pittsburgh Experiment station relative to the behavior of permissible flame Safety lamps in mine atmospheres deficient in oxygen and the effects of methan5/ on the detection of oxygen deficiency.

Jan 1, 1937

By ALBERT C. DURHAM

In anthracite mining , pumping is a problem of major importance , and water must be handled and rehandled in almost every mine whether the mine is in operation or idle . The motor - driven centrifugal pump is the most commonly used type of unit for the large pumping installations, and experience has . proved that fully automatic control has certain advantages over manual control . Some of these advantages are greater safety for maintenance personnel , continuous protection against faulty operation , which could cause damage to the Lumping apparatus , and lower pump -room operating costs .

Aug 1, 1948

By Richard H. Singleton

Native asphalt was produced in 1978-79 by six companies in four States. Leading States were Texas and Utah. Output in-creased 37% in 1978 to 1.7 million tons and decreased 5% in 1979 to 1.6 million tons while value increased 39% in 1978 to $19.3 million and 33% in 1979 to $25.6 million. Bituminous limestone was produced by Whites Uvalde Mines and by Uvalde Rock Asphalt Co. in Uvalde County, Tex.; by Southern Stone Co. in Colbert. Ala.; and by Barton County Rock Asphalt Co. in Barton County, Mo. The product was used mainly in street and road repair. Gilsonite was produced by American Gilsonite Co. in Uinta County, Utah, and by Ziegler Chemical and Mineral Corp. in Weber County, Utah. This material was used for purposes other than road repair.

Jan 1, 1980

By Charles F. Weber

Premature blasts of charges of explosives have caused many deaths in anthracite mines, and the causes of many of the blasts were not determined satisfactorily. Investigators often found fairly high potential differences between such metallic objects as rails, pipes, conveyor lines, or sheet-iron chutes in the working place where an accident had occurred. At one mine where a premature blast occurred in a rock tunnel, one workman was killed and two others were injured, and several days later a potential difference large enough to explode an electric squib was detected between the compressed-air pipe and the track rail; the voltage fluctuated and appeared to change with the movement of a locomotive. At another mine, a. workman was killed when a primed cartridge that he was about to load in a blast hole exploded in his hand. During the investigation, a potential difference was found between the conveyor line and the sheet-iron chute. During a 5-year Period, 61 fatalities and 771 nonfatal injuries were caused by explosives accidents in anthracite mines, and one of the chief causes of these accidents was premature blasts.

Jan 1, 1950

By Thomas Varley

Data on the consumption of reagents used in flotation during the years 1923 and 1924, in metallurgical plants in the Unites States, are presented in this paper. Two previous reports Lave been issued by the Bureau of Mines on consumption of oils and other reagents used to flotation - namely, "Statement of Flotation Oils," by O. C. Ralston, issued in 1913, and Serial No. 2203, "Consumption of Reagents Used in Flotation," by Thomas Varley, for the year 1919, issued in January, 1921.

Jan 1, 1925

In this Part, we have included copies of the flip charts and overhead projector viewgraphs used in the two briefings we conducted as part of this seismic detection and location task. The first one was an overview and problem definition briefing given to the seismic consultants on September 7, 1972. The second was a formal oral presentation of study results to technical staff members of the Pittsburgh Mining and Safety Research Center on November 21, 1972.

Jan 1, 1974

By D. R. Babich, E. R. Bauer

The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting a cross-sectional survey of equipment sound levels and worker noise exposures in the stone/aggregate mining industry. Six stone/aggregate mines (three surface and three underground) were recently surveyed, and the findings (ire presented here. The surveys consisted of sound-level measurements conducted around various equipment and machinery (including stone processing and crushing equipment) and full-shift dose measurements to determine worker noise exposures. The findings identify the equipment and machinery that are likely to cause worker overexposures and identify the workers found to he experiencing overexposures. In addition, the benefit of cabs in reducing mobile equipment operator noise exposure is discussed.

By E. Chin

The production of crude mineral commodities in Bangladesh was limited to natural gas, a small amount of construction materials, and clay for ceramics and bricks. No metallic minerals were mined. The only mineral commodity of economic significance was natural gas. Natural gas production has 'been climbing steadily and becoming an increasingly important source of energy for the country. Proved gas reserves were over 4.5 trillion cubic feet, but the amount has been increasing as exploration discovers large new deposits. Some sources quote reserves at over 10 trillion cubic feet.

Jan 1, 1984

By E. L. Litchfield

This report of work by the Federal Bureau of Mines has two primary objectives: A survey of the present status and usefulness of the minimum ignition-energy concept, and the presentation of recent data that are believed to bear on the safety problem associated with the ignition of combustible gases by electric discharges. The minimum ignition-energy concept has widespread applicability, especially to safety. The primary obstacle in making theoretical calculations of the requisite ignition energy is the lack of data on chemical kinetics and flame hydrodynamics. The new data on electrical ignition are representative of the great increase in knowledge that can be achieved by proper utilization of geometrical and electrical characteristics associated with the ignition source. CONCEPT OF MINIMUM IGNITION ENERGY The basic concept of a minimum ignition energy (the minimum amount of energy required to cause ignition) follows quite naturally from general physical principles and from the stability (lack of chemical reaction) of the gaseous mixture under the initial conditions. It also follows that if, as a first condition, lossless, instantaneous, and spatially localized energy can be injected and, as a second condition, the relaxation time for conversion of this type of energy to the type required for the reaction is short compared to some characteristic time scale of the ignition phenomenon, the energy requirements will be essentially independent of the type of energy source. Even if condition one cannot be fulfilled, it is sometimes possible to estimate the energy content of the gas required for ignition, and under these circumstances, condition one is fulfilled in effect. There are several instances where results can be interpreted for circumstances that effectively satisfy conditions one and two; these will be discussed later.

Jan 1, 1960

By Larry A. Haas

The U.S. Bureau of Mines investigated the use of organic binders as substitutes for bentonite in agglomerating iron ore concentrate. Over 30 organic binders were evaluated at several dosage levels in laboratory tests. The binder groups producing the greatest green pellet strengths were natural gums (guars carboxyl methyl celluloses) and gelled starches. The nongelled and alkalized starches, starch acrylic copolymers) wood-related products, and dairy products were less effective but better than bentonite. The highest wet pellet drop numbers were obtained with binders that had a medium plate water absorption value (>500 and <10)000) in distilled water and a high slurry viscosity (>75 cP) at 6 pet solids. The highest dry compressive strengths were obtained with binders that gave the highest adhesive tensile strength (>4 kg/ cm2) on iron oxide lap-joint substrates. Pellets with 0.1 pct organic binder had lower compressive strengths and reduction disintegration indices than those with 1 pct bentonite, but higher reduction rates. Pellets with carboxyl methyl cellulose and gelled starch had higher softening temperatures than those with bentonite. Overall, the most promising binder is gelled starch. Its price makes it more cost effective than carboxyl methyl cellulose, and its pellets have metallurgical properties superior to those of bentonite pellets.

Jan 1, 1989

By Charlie Wyche

The principal minerals produced in the Dominion of Fiji in 1982 were unrefined gold, silver, and tellurium. The combined value of these commodities was about $16 million,2 representing over 85% of the total value of mineral output. Cement, sand and gravel, and quarry products were the other minerals produced in Fiji. Despite the small part played by minerals in Fiji&apos;s economy, exploration on land and in the coastal areas was carried out by several international mining companies representing Australian, British, Canadian, West German, and U.S. interests. At the end of 1982, 30 prospecting licenses covering 2,300 square kilometers were issued. Most licenses were for copper, zinc, gold, and silver. Total expenditure on mineral exploration was $3.5 million.

Jan 1, 1984

By S. J. Schatzel, J. Cervik, A. A. Campoli

The cross-measure borehole technique is being studied by the Bureau of Mines as an alternative to the use of surface gob boreholes as a means of controlling methane in gobs during longwall mining. Small-diameter holes are drilled from underground locations into strata overlying the mined coalbed. When the roof strata are fractured by the mining opera- tion, a partial vacuum applied to the boreholes draws the methane out of the fractured strata and prevents it from entering the mine ventilation system. Tests in the Upper Kittanning Coalbed showed that 50 pct of the methane produced by the longwall mining operation was captured by the cross-measure boreholes. Borehole inclination and penetration into the gob are two important borehole parameters that affect the performance of the cross-measure borehole system.

Jan 1, 1983