Search Documents

By Michael J. Friedel

As part of an investigation aimed at improving the health and safety and competitiveness of the mining industry, the U.S. Bureau of Mines evaluated the application of common offset radar profiling, using a 250-MHz ground-penetrating radar (GPR) system, for the detection of fractures in igneous rock. A series of radar reflection surveys were conducted to detect and delineate the extent of fracturing at various granodiorite and gabbro quarries and outcrops located in Minnesota. The application of radar profiling for detecting joints, sheeting fractures, shear zones, and depth to water table was demonstrated to be feasible with minimal processing. Radar reflection interpretations were verified by visual inspection of the rock mass and field mapping of local structure. The radar reflection section provides a simple, rapid, and cost-effective means for mapping of shallow (less than 10 m) small-scale fractures (greater than 0.25 cm) in igneous rock masses (characteristic of velocities between 0.061 m/ns for gabbro and 0.125 m/ns for granodiorite). Depth or distance estimates to fractures are within 10 pct of the actual, and time-shift compensation is necessary only when topographic irregularities exceed 30 cm.

Jan 1, 2010

By Ludwig Schmidt

The consumption of gasoline in the United States varies materially with the seasons; during some of the summer months it exceeds the rate of production and in the other seasons the production of gasoline exceeds the consumption, The usual practice of the larger refiners is to store surplus stocks during the winter season in order to meet the heavy demands during the summer months. The following table shows the stocks of gasoline at refineries on the last day of April for the past five years: 1919 593,616,170 gallons 1920 643,5526644 " 1921 747,222,900 " 1922 892,567,766 " 1923 1,336,417.871 "

Jan 1, 1923

By R. J. Heemstra

A continuous flowing paper electrophoresis cell was used to separate petroleum and petroleum extracts into characteristic patterns. The electrophoresis of Bachaquero, Lagunillas, Boscan, and Gibson petroleums in nitro-benzene and acetic acid-based electrolytes was investigated. The extent of separation in the patterns was studied by measuring the metal and porphyrin contents of the effluents. Qualitative separations were achieved in some systems, whereas either system demonstrated only a high degree of electrophoretic migration.

Jan 1, 1967

By E. P. Youngman

A new mining law for the Recublic of Polend was promulgated by presiden- tial decree dated November 29, 1930, published in the Journal of Lews (Dzienni stex) No. E, text 654, December E, 1530, and wes to become effective January 1, 1932, in all Polend except Silesie. Its adoption in Silesia wes dependent pon the action of the Silesian Diet. As the new law is considered an im- provement over the old Austrian Mining Lew, which is operative in the Silesian districts of Bielsk and Cieszyn, and the Prussian Kining Law, which is opera- tive in Upper Silesia, no delay in its adoption for Silesin was looked for. This new law codifies the various juridical regulations pertaining to ines existing in different parts of the Polish Republic but does not include legislation with respect to the extraction of minerel oil, especially crude oil. Petroleum legislation was postponed to a later date in order to facili- tate codification in other fields. Koreover, as the oil industry exists in Galicia elone, deley will not be detrimental.

May 1, 1932

By W. E. Wallace, C. A. Hill, M. J. Keane

"Diesel exhaust particulate material from exhaust pipe scrapings of two trucks, diluted automobile diesel exhaust particulate material collected on filters, and two oil shale ores were prepared for the Ames mutagenrcity assay by dichloromethane OOP ex¬traction, by dispersion into 0.85% saline, or by dispersion into dipalmitoyl lecithin (DPL) emulsion in saline. Salmonella typhimunum TA98 was used to detect frameshift mutagens in the samples. Samples of diesel soot gave positive mutagenic responses with both DCM extraction and DPL dispersion, with the DPL dispersion giving higher results in some cases. The results suggest that possible mutagens associated with inhaled particles may be dispersed or solubilized into the phospholipid component of pulmonary surfactant and become active in such a phase.INTRODUCTIONThe Ames Salmonella/microsome assay (Ames et al., 1975) has been shown to be a useful test for detecting genotoxic properties of various agents. Hundreds of specific chemicals have been screened (McCann et al., 1975), and the test has been applied for many types of environmental samples. Airborne mutagenic agents, for example, have been found in urban air (Chrisp and Fisher, 1980; Hughes et al., 1980; Ro· senkranz et al., 1978), in diesel engine exhausts (Huisingh et al., 1978), and in the by-products of coal combustion processes (Chrisp et al., 1978).Samples of airborne particles are typically collected on membrane filters, and undergo a rigorous extraction procedure with organic solvents and/or ultrasonic agitation (Clark and Hobbs, 1980). Often extracts are transferred to another solvent that is compatible with the assay system. These extraction procedures, while efficient from an analytical perspective, are not physiologically plausible. The questions that present themselves are whether a demonstrated mutagen can be taken up in vivo and whether the process is quantitatively or qualitatively different from the above laboratory procedure (Wallace et al., 1984).When a particle of respirable size is inhaled to the alveolar region of the lung, its first physiological contact is with pulmonary surfactant that lines the inner surfaces of the alveoli. This surfactant is an aqueous fluid containing proteins, phospholipids, and other components (R. J. King, 1982). The principal phospholipid constituent is L·alpha-phosphatidylcholine, beta,gamma-dipalmitoyl, or dipalmitoyl lecithin (OPL) (l. C. King et al., 1981)."

Jan 1, 1989

By E. Divers

This Bureau of Mines report presents results of an underground evaluation to determine the respirable dust and gas control effectiveness of a combined (push-pull) face ventilation system for coal mines. The system utilizes both blowing and exhaust curtain, continuous miners equipped with radio remote control, and flight conveyors. Bureau of Mines tests showed a 97% reduction in respirable dust concentrations from the usual cab position on the continuous miner to the remote control operator's position. This allowed the remote control operator to be well within, and the usual cab position to exceed, Federal respirable dust standards. Tests utilizing a safe tracer gas, sulfur hexafluoride (SF6), to determine the face ventilation effectiveness of the combined blowing and exhaust system showed that the system also has excellent methane dispersion capability. Where wide entries permit, this combined face ventilation system and use of remote control can be a very effective method for dust and gas control.

Jan 1, 1982

By Zsuzsanna Zborovszky

Experimental study directed toward gaining improved understanding of the exact mechanisms causing ignition in the PTB breakflash. Investigation and comparison of tungsten and copper wires as to their ability to cause hot wire ignition. Evaluation of the importance of discharge duration in the ignition process. Study of the parameters influencing the duration of a discharge (minimum discharge voltage, purity of electrode materials, purity and properties of the gaseous atmosphere contaminations, deposits on the electrode surface).

Jan 1, 1976

By J. B. Gayle

Coke-pushing difficulties have been the subject of much controversy but relatively little scientific investigation. Nevertheless, continuing pushing difficulties can greatly decrease the life of a coke oven and should therefore be considered in the selection of the blend and operating conditions used for coke production. The present Federal Bureau of Mines investigation was undertaken to correlate results of previous investigators and to supplement these results to the limited extent practical by us of an experimental slot-type oven. To this end, pushing pressures have been determined routinely for Tuscaloosa oven tests conducted during the past 10 years. Nevertheless, the accumulated information remains incomplete in many respects, and in view of the recognized inadequacies of the data, publication is now undertaken only because of the scarcity of published information on this important problem and the discontinuation of carbonization studies with this oven.

Jan 1, 1961

By Foster Fraas

Calculations based on data related to the electrostatic precipitator illustrate the variation in the electric forces on a particle with change in position in the ionized field. The feeble forces in some separators are explained by the low field intensity at midpoint locations between the electrodes. When the particles are in contact with the exterior surface of a rotating cylindrical electrode, a high field intensity at the electrode surface combined with the image charge results in large electric forces. The permissible feed velocity increases as the square root of the electrode diameter, providing high values in efficiency and feed rate capacity, particularly in surface-to-mass ratio separations such as are encountered in secondary materials recycling operations.

Jan 1, 1971

By I. AITKENS

Quartz maintains a rather conspicuous position among gem stones , despite its being the commonest and, in its natural form, the most easily recognized of mineral substances . This prominence is due primarily to the extensive use of amethyst , which provides stones of the finest violet color , and also to the wide employment of yellow quartz ( citrine ) which is called topaz by jewellers and vies with the true topaz in color and brilliance . Unlike many less costly gem materials quartz is hard and durable .

Mar 1, 1932

By D. A. Reynolds, L. P. Rockenbach

"The method of analyzing light oil for benzene is fully described by Fieldner and others 4/ and Kester and Kolmes 5/. In this procedure, benzene is determined by shaking 20 cc. of the 79º to 81º C. boiling point cut from the fractionation of the refined light oil with 3 volumes of 98—percent sulfuric acid in an A. S. T. M. separator funnel of the type used for determining water in bitumi¬nous materials. After the mixture has been shaken 5 minutes it is allowed to settle at least half an hour and the acid is drawn off; the residual oil is reported as paraffins and the decrease in volume as benzene. The method has been found satisfactory for light oils from coals carbonized at 5000, 600°, and 7000 C. but does not give accurate, reproducible results for oils from the 800° C. tests.The content of benzene of the 790 to 81° C. cut is high, 90 to 95 percent, for 800° C. light oils, whereas for lower—temperature light oils it is considerably less. Benzene is the most difficult of the aromatics to sulfonate, hence the acid concentration must be maintained above 95 percent to insure complete sulfonation. Sulfuric acid (98 percent) reacts with benzene, but its reaction with paraffins at ordinary temperatures is negligible; however, more concentrated acid will attack paraffins and give erroneous yields of benzene. The reaction between benzene and sulfuric acid forms water that will dilute the acid. The effect of this dilution may be overcome by increasing the acid-to-oil ratio or increasing the strength of the acid. The latter, however, must not be used, because the stronger acid reacts with paraffins."

Mar 1, 1942

By Daniel N. Tallman

To provide technology for achieving more efficient water filtration systems for the mineral industry, the Bureau of Mines performed demon-stration filtration tests at three iron ore mines and one steel mill. A comparison of equivalently sized magnesium oxide (MgO) and sand filters showed that MgO had a higher capacity and could operate at higher fil-tration rates than sand. In demonstration tests when alum (AlK(S04)2) was the coagulant, suspended solids breakthrough occurred even though the pressure across the filter (head loss) was 7 psig or less. Under these circumstances, the MgO demonstrated 20 to 100 pct greater filtra-tion capacity, defined in terms of the volume of water filtered before breakthrough. When an organic floccu1ant was used at one location, head loss was the run-limiting factor; the filters essentially plugged with-out any solids breakthrough.

Jan 1, 1985

By Vernon F. Swanson

Several laboratory flotation tests were conducted by the Bureau of Mines on a sample of unweathered diorite from the B. F. Camden property, Amherst County, Va. Results showed that an ilmenite concentrate analyzing 45.5 percent Ti02 (titania), 0.07 percent P205 (phosphorus pentoxide), and 2.21 percent Si02 (silicon dioxide) could be produced from a feed containing 7.72 percent Ti02 and 3.94 percent P205. Ti02 recovery in the concentrate was 47.6 percent in a batch test. The weathered saprolite material overlying the diorite required scrubbing and desliming to remove argillaceous material and preliminary flotation of apatite followed by flotation of ilmenite. The resulting concentrate analyzed 47.3 percent Ti02, 0.19 percent P205, and 0.99 percent Si02 from a starting feed of 8.99 percent Ti02 and 3.37 percent P205; TiO2 recovery was 54.5 percent.

Jan 1, 1963

By William J. Campbell

The purpose of this investigation was to develop a rapid, accurate method of analysis for small amounts of calcium in wolframite concentrates. This analysis is necessary to determine if the wolframite concentrates meet United States National Stockpile Specification P-57R2, which limits the calcium content to 0.2 percent. Because of the small depth of the sample analyzed in fluorescent X-ray spectrography, the calcium Kaline intensity was a function of the chemical composition of the calcium-bearing particle as well as the total matrix composition. This particle-composition effect was particularly important in this analysis, as the calcium may be present as a carbonate, tungstate, phosphate, etc. Three methods of preparing the sample eliminated the variation of calcium Ka intensity with mineralogical occurrence: (1) Reduction in particle size by extensive grinding, (2) chemical fusion with sodium carbonate, and (3) solution of the calcium by an acid attack.

Jan 1, 1958

By Robert L. Virta

The Bureau of Mines examined a fibrous talc sample from the Gouverneur talc district in New York by transmission electron microscopy (TEM) and polarized light microscopy to determine the mineralogical relationship of the fibrous talc to the amphiboles present in the sample. Two am-phiboles, anthophyllite and tremolite, were present in the sample. Tremolite occurred as a separate mineral phase, which was blocky in habit. Only a few composite tremolite-talc grains were observed. An-thophyllite, however, was present only in the fibrous talc grains. Mi-crodiffraction study of the fibrous talc grains containing anthophyllite showed that the anthophyllite was intermixed with the talc on a fine scale and that there was a crystallographic relationship between the talc and anthophyllite lattices in the fibrous talc grains. A mechanism similar to the process that forms biopyriboles could explain the structural defects, the fibrous habit of the talc, and the structural relationship between the talc and anthophyllite in the fibrous talc grains. Because of these characteristics, phase contrast microscopy and a provisional TEM technique for monitoring asbestos exposure would not distinguish between fibrous talc and fibrous amphiboles. TEM techniques employing electron diffraction and energy-dispersive X-ray analysis are recommended to positively identify the fibrous phases for regulatory purposes.

Jan 1, 1985

By Larry G. Stolarczyk

This report deals with the creation of an efficient method to determine if command, control, communication and monitoring (3cm) equipment in coal, metal and non-metal mines is susceptible to Radio Frequency Interference (RFI) from the Medium Frequency (MF) radio communications system. A qualitative and quantitative RFI test plan was developed for in-mine and laboratory evaluation of the equipment. The laboratory testing was accomplished using the TEM Test Chamber. Detailed information on the Test Plan and the TEM Test Chamber is included. During in-mine testing of the MF System some underground equipment malfunctioned when the transmitter's radiating antenna was in close proximity. Electromagnetic Compatibility (EMC) testing was done on three levels; Component (circuit or box), subsystems and system. Nine tables are included which show the results of testing various equipment for RFI.

Jan 1, 1986

By J. B. Gayle

Many investigators have reported studies of size distributions for particulate solids ; usually , these have involved the fitting of size distribution data to a particular mathematical function . Such studies are of unquestioned value and have contributed much worthwhile information regarding the breakage mechanisms for a variety of brittle materials . In connection with a Bureau of Mines study of the size distribution of coke , which has been subjected to the standard American Society for Testing Materials (ASTM) tumbler test , attention was focused on the relation between the 1 -inch tumbler index (usually considered to be indicative of the ability of coke to resist degradation by impact ) and the 1 /4 - inch tumbler index ( indicative of the ability to resist degradation by abrasion ) . Specifically , it was noted that for certain sets of data the correlation coefficients denoting the relation between these indexes were positive ; for other sets of data , these coefficients were negative . Preliminary consideration of this problem indicated that the usual interpretation placed on correlation coefficients was erroneous in this particular instance because the variables being correlated were necessarily related . The work described in this report was undertaken to clarify the interpretation of results of correlation studies for variables of this type .

Jul 1, 1960

This Bureau of Mines publication describes the plan used to instrument two longwall gateroads at the Powhatan No. 4 Mine of the Quarto Mining Co. Vibrating wire stressmeters, flat jack U-cells, multipoint extensometer stations, and convergence stations were installed in or on the coal pillars, roof bolts, and roof strata of the gateroad entries. The instruments measure pillar stresses, bolt loadings, and strata movements as the gateroad entries are developed and the longwall panel(s) is mined. The report details only the instrumentation plan of the longwall gateroads and not the evaluation of any subsequent data. This is because a complete analy-sis of the data cannot be made until extraction of the longwall panel(s) is complete.

Jan 1, 1982

By A. A. Sonnek

A simple, portable helium analyzer was developed primarily for field use. Its utility lies in making preliminary surveys before exact analyses are required. The analyzer is based upon chromatographic principles; that is, separation of gas mixtures resulting from variable retention times of the components with respect to a separation medium (column-packing material). It uses thermistors for sensing detectors, a dry battery as source of power, and a micro-ammeter for indicating helium concentration. The absolute accuracy of the instrument depends upon the recency and care with which the instrument is calibrated with a standard gas. The unknown gas should be analyzed immediately after calibration, and another calibration should be made before another unknown sample is analyzed. The instrument is simple to operate, requiring approximately 15 minutes, after calibration, to determine the helium content of a natural gas sample. Although developed primarily for helium determination, the analyzer possibly can be used for other analyses that can be performed at ambient temperatures.

Jan 1, 1965

By R. J. Marek

The number of persons fatally injured in the California petroleum industry in 1931 was 30, a decrease of 20 fatalities or 40 per cent from the number killed in 1930. As a result of the decrease in the number of fatalities for 1931, the fatality curve of the California petroleum industry reached its lowest point in nine years. Although reductions in personnel--which permitted the retention of a select and experienced class of workmen, decreased active field-development work, and curtailed production--undoubtedly have had a marked effect on reducing the number of fatalities in 1931, the decrease also has resulted from continued accident-prevention efforts. Statistics show that a direct relationship exists between development activity and the number of men accidentally killed in the drilling and producing division of the California petroleum industry. For example, when the average number of drilling wells in 1930 was 29 per cent less than in 1929, the number of men accidentally killed at drilling wells dropped 48 per cent; and when the average number of drilling wells in 1931 decreased 52 per cent from 1930, the number of fatalities at drilling wells decreased 58 per cent. The relationship between field-development work and fatality frequency is significant because each year at least 50 per cent of all the fatalities in the California petroleum industry occur in the drilling and producing division. This relationship should serve to guide the accident-prevention efforts of the industry, especially in the drilling and producing division, toward checking an increase in fatal accidents when development activity again takes an upward trend.

Jan 1, 1932