Search Documents

By S. W. Parr, T. E. Layng

There is presented below the results of experiments made on six samples of Utah coals furnished through the U. S. Bureau of Mines , under an agreement dated June 16th , 1920. The details of all values for all runs are tabulated and presented herewith . Clear The samples, consisting of approximately 150 pounds each, were received at the University of Illinois , on June 15 , 1920 , and are listed as follows : Creek , Wattis , Castle Gate , King , Standard , and Aberdeen . The proximate and ultimate, analyses of the various ccals from that region , representing all the types included in these samples , have already been made by the Bureau of Mines , and are available . * Similar determinations were also made on the particular samples forwarded for purposes of these experiments . The results obtained on the coal as received did . not very in any material feature from the values reported by the Bureau, they are shown in Table 1. It is of importance to note only that the oxygen content is uniformly high , namely approximately 9.5 to 11.5 per cent of the as- received coal , while the oxygen - hydrogen ratio is also high, being on the average approximately 2 ( oxygen) to 1 ( hydrogen) .

Sep 1, 1921

By L. B. Pankratz, R. Barany, W. W. Weller

Experimental determinations were made of the heats of formation at 298.15 ° K of cuprous ferrite and cupric ferrite ; the heat capacity of cuprous ferrite was measured over the temperature range from 50 ° to 298 ° K and the entropy at 298.15 ° K was evaluated ; the heat contents of cuprous ferrite and cupric ferrite above 298.15 ° K were measured to 1,500 ° K and 1,100 ° K , respectively . These thermodynamic values were combined with other pertinent data to obtain heat and free energy of formation values at high temperatures . The stability of the two ferrites with respect to their constituent oxides is discussed . Thermodynamic values are included for the decomposition of cupric ferrite to form cuprous ferrite , magnetite , and oxygen .

Jan 1, 1964

By Juel H. Stears

Research was done to determine if a hydraulically operated penetrometer developed by the Bureau of Mines could be used to estimate the roof-bolt anchorage capacity of mine roof rock. Tests were conducted both in the laboratory using cement cylinders and underground in shale rock. Hardness readings were measured by the penetrometer around the periphery of the bolt holes at the anchorage horizon. Roof bolts Nere then installed and subjected to an anchorage test. The results showed that the penetrometer readings could be used to determine the optimum stratum for roof-bolt anchorage but could not be used to make an accurate estimate of the anchorage capacity.

Jan 1, 1965

By Michael J. Klishis

It was the goal of this project to develop training materials specific to two areas of the mining industry: (1) safe use and care of the self-contained self-rescuers, and (2) awareness and avoidance of electrical hazards. This report describes the development of the following training material: Instructor's modules for the OCENCO EBA 6.5, CSE AU-9A1, and PASS 700E self-contained self-rescuers; and a textbook, slide tapes, and accident case study scenarios for mine electricity, and a computer based instructional package on mine electricity and electrical hazards. The report concludes that additional efforts are needed in mine training and four recommendations are made: (a) tailor existing materials to fit specific mine sites, (b) develop and evaluate computer based instructional material, (c) develop parallel training materials for metal and non-metal mines and, (d) develop additional training materials for preparation plants and surface areas of underground mines.

Jan 1, 1985

By L. B. Pankratz

High-temperature heat contents were measured for two praseodymium oxides and three terbium oxides. There were: Pr2O3 (298° to 1,600° K), PrO1.833 (298° to 1,050° K), Tb2O3 (298° to 1,600° K), TbO1.719 (298° to 880° K), and TbO1.812 (298° to 850° K). With the exception of PrOl.833, all results were regular. PrO1.833 had a small thermal anomaly at 760° K with an extra absorption of 380 cal/mole. The measured heat content values, tabulated smooth heat contents, and entropy increments are reported. Heat content equations were derived.

Jan 1, 1966

By T. A. Henrie, E. K. Kleespies

Carbon reduction of rutile and ilmenite in nitrogen and ammonia atmospheres was studied as a method of preparing titanium nitride . Ammonia was a better nitriding agent than nitrogen . The contact between the solid reactants , carbon and rutile , was a prime factor in nitrogen atmospheres and was of lesser import in dissociated ammonia . The reduction process for conversion of rutile to the nitride required carbon . The nitriding of ilmenite- carbon mixtures produced titanium nitride and elemental iron .

Jan 1, 1964

By R. V. Ramani, R. Bhaskar

"While the National Academy of Sciences has stated that gravimetric sampling technology for compliance purposes is adequate, research into various aspects of respirable dust control require data on many other parameters of airborne dust. These, in turn, have created the need to use many instruments, other than personal gravimetric samplers, in mi ne environments for dust measurement. There is a need to evaluate the performance of these instruments under conditions of potential use.As part of research in the Generic Technology Center for Respirable Dust, cascade impactors, gravimetric personal samplers and gravimetric samplers collecting dust using isokinetic sampling principles were employed for dust measurements under identical conditions in a mine airway. During the course of the experiments, 8-stage cascade impactors and gravimetric samplers drawing air isokinetically were located in the center of a mine airway at various stations. Two types of data were examined - concentration of dust and size distribution of the dust collected in the samplers. The data show that the amount of dust collected by an impactor is less than half the amount collected isokinetically. The size distributions of the dusts collected from the two instruments, though comparable, show a consistent difference in median diameters. The cause for this bias is examined.The paper presents and discusses the results of the tests, including the concentrations and size distributions obtained from the two instruments for different experimental conditions. There is a need to document the performance of various dust measuring devices in mine airflow conditions.INTRODUCTIONThe sampling of airborne dust in mines can be done for several purposes. Traditionally, dust sampling has been restricted to the gravimetric measurement of airborne respirable dust to comply with the regulations governing the mining industry. Instruments such as the MRE gravimetric sampler, and personal gravimetric samplers that have collection characteristics similar to the human respiratory system have been in use for the last two decades. Presently available instrumentation for the purpose of regulation have been considered adequate by the Committee on the Measurement and Control of Respirable Dust in Mines (National Academy of Sciences, 1980),"

Jan 1, 1989

By Peter K. Mathison

The U.S. Bureau of Mines has developed a hydrologic monitoring system for in situ leaching operations. This system records and displays flow and pressure information from sensors located in leachant injection and recovery wells. Continuous monitoring of hydrologic conditions is important during leaching operations because hydrologic factors such as aquifer permeability, solution injection rates, injection pressure, and solution recovery rates interact and change over time. This hydrologic monitoring system has been tested in an underground setting at the Cyprus Casa Grande copper mine. The system consists of hardware and computer software components and includes two Bureau-developed software applications. This publication describes the implementation of the hydrologic monitoring system and the software developed at the Bureau in support of in situ leaching research.

Jan 1, 1994

By J. H. Hild

The Shanton magnetite-ilmenite deposits lie on the east flank of the Laramie Mountains, 43 miles northeast of Laramie, Albany County, Wyo. (fig. 1). The Shanton and other similar deposits in the Laramie Mountains were examined by Bureau of Mines engineers during 1942, 1943, and 1945, and a report2/ describing the results of a dip-needle survey and surface sampling was published in 1946. The Shanton deposits occur in a relatively flat section of the range at altitudes varying from 7,500 to 1,650 feet (fig. la). Prevailing rocks in the Shanton area consist of anorthosite with intrusive dikes of gabbro differentiates and granite. Titaniferous magnetite outcrops in five masses, which are separated at the surface by overburden and anorthosite.

Jan 1, 1953

By L. A. Morley

Volume III of the final report examines the indication versus interruption procedures used on motion-drive power equipment, with emphasis on surface excavators. The report begins with a review of the electromechanical acid conversion used with the Ward-Leonard control system. Protection criteria for the drive-system components are then discussed. Fault sources and fault calculations for both the ac supply source and dc power loop are introduced to assist in discussing indication and interruption procedures. The subject is then expanded to examine the dynamic process of the machine and determine the effects of fault current and position of the machine to allow for an orderly shutdown. With this analysis, possible indication an interruption procedures are given for the four-quadrant duty cycle of excavators. The report concludes by introducing other mining operations that utilize similar motion-drive systems and also static (solid-state) drives and recommends further research in these areas, as well as a more detailed examination of the dynamic fault analysis for excavators.

Jan 1, 1982

By Nicholas Kyriazi

A joint effort by the U.S. Bureau of Mines (USBM) and the U.S. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CPR 75.1714), held up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSR's in the fourth phase of testing from 1989 to 1993. The SCSR's were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except units with manufacturing defects. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. In addition, some apparatus collected for this study had not been returned to the manufacturer in a recall effort for correction of a manufacturing defect. In both cases, the apparatus would have presented problems in emergency use. Recommendations include improved training in inspection procedures and better enforcement of recall notices.

Jan 1, 2010

By C. E. Wicks, J. E. Tress, F. E. Block

The Bureau of Mines investigated the effects of gamma radiation on materials and chemical reactions to obtain information that could be of value in modern metallurgical practices . Various combinations of metals and their ores and compounds were irradiated in attempts to effect reactions that might be applicable in the extraction and separation of metal values from minerals and The types of reactions studied included complexing of salts , decomposition of hydrated salts , metal chlorination reactions , leaching of ores and minerals , halogen exchange , and various reducing reactions . All irradiations were performed at the Materials Testing Reactor Gamma Facility of the U.S. Atomic Energy Commission at Idaho Falls , Idaho . Spent fuel elements were utilized as the source of the gamma radiation . Some irradiation - induced changes , ranging from mere color change to participation in chemical reactions , were noted . The greatest value of these investigations , however , was the experience acquired , which should be valuable in future explorations of similar nature .

Jan 1, 1964

By Foster Fraas

The Bureau of Mines investigated a method for calculating values of adsorption energy; the goal was to devise an equation consistent with experimental data accumulated in the investigation of adsorption as related to ore separation processes. Numerical identification of the constants of a previously formulated equation provided an equation by which values of adsorption energy could be calculated. Values thus calculated checked with those obtained by calorimetric measurement.

Jan 1, 1965

By Alan G. Mayton

The Bureau of Mines conducted a study to (1) determine from laboratory tests the feasibility of a photographic method for determining reflec-tances that may be applied to measuring in-mine mineral reflectances and (2) formulate a procedure for collecting and analyzing the data. The method uses a 35-mm camera with automatic flash and a gray-scale re-flectance standard to collect on film the reflectivity data in under-ground mineral mines. After the film is processed, the data on the photographic prints are analyzed in the laboratory with a photometer. Test results show the photographic method can provide values of reflec-tance to within ±5 pet of full scale (full scale = 100 pet). The method's usefulness for determining reflectivity values, within similar limits of absolute percent error at the lower end of the scale, however, has not been completely resolved by the study and consequently warrants further investigation. The method offers an acceptable means for collecting and analyzing reflectivity data for reflectivities at the higher end of the scale, i.e., 50 pet or above; it should be used with caution when reflectivity values are below 50 pet. Four films were evaluated; all gave relatively satisfactory results.

Jan 1, 1987

By W. J. Fene

Ventilation is undoubtedly the greatest single safety factor in the operation of a coal mine. Any condition or occurrence that interrupts the ventilating current or changes its normal course through the mine workings is a distinct hazard and should be considered as such by every coal-mine owner, operator, and worker. The hazard, of course, is much greater in a mine that is emitting gas, as an explosive mixture can accumulate in a very short period if the ventilating current is interrupted. It is common to find one or more entries producing 600 cubic feet or more of methane per hour. If the ventilating current were short-circuited from these entries for 15 minutes, there would be an accumulation of 150 cubic feet of methane, which, when mixed with enough air to dilute it to the lowest explosive point, would make about 3,000 cubic feet of explosive mixture; this gas could be ignited in almost any normally operated mine by a cutting machine or other electrical equipment. The ignition of this quantity of an explosive gas-air mixture can readily cause an explosion of coal dust that would completely wreck the underground workings and possibly some of the surface structures. In fact, the ignition of one-tenth of the above quantity of an explosive mixture of gas and air might readily start an explosion that would, extend through every part of a large mine. The possibility of occurrence of interruptions to the ventilating current has received comparatively little consideration from mine owners, operators, and workers in many parts of the United States. Such a possibility should be considered in connection with every mine that gives off explosive gas, and steps should be taken to prevent it.

Jan 1, 1943

By Fred C. Turin, William J. Wiehagen

This study examined musculoskeletal injury risk at four mining sites: underground coal, underground limestone, surface copper, and surface phosphate. Each site offered opportunities to investigate musculoskeletal disorder (MSD) injury risks and how those risks might be identified and categorized. The National Institute for Occupational Safety and Health (NIOSH) worked with these sites to (1) identify work activities that showed evidence of MSD injury risk, (2) examine physical risk factors that can lead to MSDs for a handful of work tasks at each site, and (3) develop a set of ideas for problem-solving to help reduce risk factors for examined work tasks. For each site, NIOSH implemented a plan that was refined over the time period of this study. The plan consisted of four steps. The first step was to use mine injury records, a musculoskeletal discomfort questionnaire, front-line supervisor interviews, and a list of management concerns to identify work groups and work activities that have significant evidence of MSD risk factors. The second step was to select work tasks for evaluation. The third step was to interview those who do the work and make observations to characterize the MSD risk factors and musculoskeletal symptoms that exist for target tasks. The final step was to conduct brainstorming sessions with workers who perform the work or have a stake in the production task. The brainstorming sessions served to identify general strategies (ideas) for reducing MSD risk factor exposures. A final report of findings was presented to mine management and workforce representatives at each site. The risk factors and ideas for improvement identified for each site were specific to the target tasks examined. These target tasks were diverse, but there were some key similarities. For instance, jobs were found at each site that required a significant amount of manual work involving the upper extremities and low back. Handling heavy and awkward objects, forceful arm and shoulder exertions, and working in awkward postures were common for a variety of jobs across the four sites.

Jan 8, 2004

By D. Montagna

The Kroll-Betterton process for debismuthizing lead is based on adding calcium and magnesium to impure molten bullion to form solid Ca-Mg-Bi inter-metallic compounds that float on the surface as drosses. Present practice in industry is to hand-skim off these drosses, often followed by hydraulic pressing to squeeze out some of the entrapped liquid lead. In an effort to develop an improved technique, the use of an argon-shrouded dipping centrifuge to perform the required phase separation was investigated. Centrifugation experiments demonstrated that the bismuth content of an impure bullion could be lowered from an initial 0.5 percent down to 0.03 percent with a lead recovery of 90 percent, which is comparable to lead recovery after hand skimming of drosses in commercial lead-debismuthizing operations. Centrifugation provides better control in removing drosses, faster operation with less oxidation and relatively little fuming, and recovery of a lead bullion that approaches commercial specifications.

Jan 1, 1972

By L. D. Tracy

For many yeirs natural gas has been the principal fuel used in the he·1 ting furnaces in those mills located in the. Pi t-c;s. b.urgh district· \7hich manufacture bolts ., nuts, rivets, pick$, mattocks and srr.&11 for6ine;s. For a nUI.1"'.::>er of years the steady supply of this fuel has been more or less interrupted owing to the increased4and f·or d9mes tic use and to the increasing difficulty in securing an ad.eq_ua te c.1mount of natural gas. This condition has led a number of the steel compa.nies to substitute -oulvsrized coal a.s a fuel for the.furnaces. Elaborate irista.llations have been made for pulverizing tne coal ar!d _ coriveyi16 i -c to the fur:waces. • Soon after the furnaces ·-:commenced .. to operate ·,Vi th :pulverized coal, large quanti ties O::f.' fine dust beg.::in to accumulate on the platforms over the fu:rna. ces, the. roof trusses, on the outside of the va.rious· pip·e ·line electric cables a.i.1.d even on the roofs of the buildings. Some of tha comi:,a.n:;.0s, becomin·g alarmed, requested the Bureau of ;Unes to rr.c1ke an investigation to ascertcliin the.· licibili ty of this dust to cause an explosion.· Nhi le conducting this inves ti ga ti on,· an explosion· occurr-2! d in a.nothe:2 nill ·,7hich caused he death of one man and severely burned t;io others. Eleven sc1nrcles of the dust (which for convenience has been termed "mill d.ust 11 ) from various locations in the different mill' buildings were taken and submitted to chemical analyses, microscopic examination and also to flame and explosion tests. From the chu,1ica.l analyses it was found that· the volatile matter in th..:: dusts xanged -from 6.3 per cent to 23,54 per cent, fixed carbon from 50.88 per cent to 67.08 per cent and ash from 32.29 per cent to 32.16 per centw

Dec 1, 1919

By Byron. O. Pickard

"An Arizona mining company recently demonstrated a new use for the geophone by successfully locating leaks in compressed-air lines which were buried under from 1-1/2 to 2-1/2 feet of fine rock fill. The following information is abstracted from data sent to the Bureau of Mines by the superintendent of the mine.The company has two parallel main compressed-air lines, about one and one-half miles long, buried under an average of two feet of fine rock fill. One of the lines is a four-inch high-pressure (1000 pounds) main, and the other line a ten-inch low pressure (90 pounds) main. The two mains are separated by a 10 to 3C foot interval, and run from the compressor plant to the No. 2 shaft, where they are taken underground. A pump line is also buried in the immediate vicinity.Several leaks, not audible enough to be located, were developed in the Alms. Various =Abode were suggested that did not seem practicable to the management. Finally, the company obtained a Bureau of Mines' geophone and experimented with it. The first test& were conducted while the pumps were running, and while there was noise on the concrete pavement, all of Which caused so much vibration in the geophone that it was impossible to detect the leaks.The second attempt was made at the close of the day shift when the compressors were not operating and when the pumps could be shut down. The valves in the far end of the surface lines were closed, and the lines were pumped to full pressure (90 and 1,000 pounds respectively).Geophone readings were then taken at 7 or 8 foot intervals directly see the lines. Several leaks some very large in the high-pressure line were audible with the geophone at distances varying from 15 to 30 feet. A con-le leak in the low-pressure line was found at a distance of 10 feet. detecting the leaks, no difficulty was found in locating them exactly. ""At this time"", laid the superintendent of the mine, are unable to large a leak must be in order to be located under two feet of loose geophone. The fill we worked over was quite loose and dry and unfavorable for the work in question. However, we have no that the instrument is a valuable adjunct to our business""."

Aug 1, 1922

By C. A. Komar

Renewed interest in the underground gasification of coal evolves from comprehensive studies of earth fracture systems that indicate that the movement of fluids can be controlled in the coalbed. In particular, directional property studies of natural microfissure occurrence, permeability, ultrasonic velocity, tensile strength, and orientation of intervals of inherent rock weakness, together with geologic structure setting and fracture trace analysis, can predict the gaseous flow paths in the coalbed. Having this information, the dominant direction in which gases generated and/or liberated by heat would move can be determined so that appropriate well patterns can be developed. Together with advances made in drilling technology that permit long horizontal holes to be drilled through the coal seams, tests can be conducted to determine whether directional control will permit devolatilization of the coalbed and gasification of the remaining hot coke in a systematic manner to produce a low-Btu gas suited for the generation of electricity.

Jan 1, 1973