Search Documents

By H. Kenworthy

The objective of this investigation was to evaluate the technical feasibility of smelting certain low-grade domestic iron ores in an electric furnace. Laboratory-scale experiments showed that a high recovery of iron in the form of pig iron can be obtained from east Texas ores containing less than 25 percent iron. The pig iron was amenable to standard-or electric-furnace-refining methods for producing steel. Car-bon, silicon, and phosphorus were the primary impurities removed in refining. Overall recoveries of iron as pig iron exceeded 95 percent, in contrast with commercial mineral-dressing recoveries on these particular ores of 50 percent of the iron as a 45-to 50-percent iron concentrate.

Jan 1, 1958

The principal activities of the Bureau of Mines Explosives Research Center from July 1, 1963 to June 30, 1964 are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1964; in general; the research reported in these publications antedates the report period. Part 3 describes a short-term investigation into safety problems associated with shipping of molten sulfur; this investigation is not at present destined for publication elsewhere.

Jan 1, 1965

By R. O. Dannenberg

Applicability of the fluosilicate sintering process to recovering beryllium from beryl-spodumene concentrate analyzing 1.4 to 3.7 percent BeO (10 to 30 percent beryl) was investigated. The work was one phase of a Bureau of Mines research program undertaken to assess applicability of conventional processes and to devise new procedures for treating various potential beryllium feed materials. Beryllium recovery of about 70 percent in a product of 99-percent BeO grade was achieved in treating 3D-percent beryl concentrate. The process consisted of (1) sintering a briquetted charge of concentrate, soda ash, and sodium fluosilicate for 3 hours at 750° C.; (2) extracting the soluble beryllium by multiple stages of water leaching; (3) adding caustic to the leach solution and boiling to hydrolyze and precipitate crude beryllium hydroxide; (4) dissolving the crude beryllium hydroxide in sulfuric acid and separating the solution from undissolved silica; (5) sulfidizing the acid beryllium solution to precipitate heavy metal impurities; (6) adding ammonia to the clarified sulfate solution to precipitate beryllium hydroxide; and (7) converting the hydroxide to beryllium oxide (beryllia) by calcining at 900° C. About 60 percent more sodium fluoSilicate was required per unit of beryl than is used industrially in treating 10-to 12-percent BeO concentrate (80 to 90 percent beryl). Recovery decreased, and flux requirements increased, when treating concentrates containing less beryl.

Jan 1, 1963

By R. V. Mrazek

The heat of formation of vanadium trichloride was determined at 298.15° K. Measurements were made in a solution calorimeter in which an aqueous hydrochloric acid-potassium dichromate solvent was employed. Data are presented for the heats of solution of vanadium trichloride and the vanadium trioxide "backup" compound, and for appropriate dilution reactions needed to preserve stoichiometry. The resulting heat of formation of vanadium trichioride (VCI3) at 298.15° K was found to be ?H°298.15° K = -138.89 ±0.37 kcal/g mole.

Jan 1, 1968

By W. W. Weller

Heat capacities of ferrous molybdate (FeMoO4) and ferrous tungstate (FeWO4) were measured over the temperature range 51° to 298.15° K. Ferrous tungstate has a lambda type heat capacity anomaly at 74° K. The 298.15° K entropies are FeMoO4) 30.9 cal/deg mole and FeW04) 31.5 cal/deg mole.

Jan 1, 1966

This U.S. Bureau of Mines (USBM) report conveys the results of an economic analysis of minerals in the West Mojave Management Area (WMMA), including the Desert Tortoise Priority Habitat (DTPH), a proposed special land management area. Undiscovered mineral resources were estimated for the entire WMMA, which totals 8.7 million acres. Known mineral resources were studied for the DTPH, which is an area of 1.2 million acres contained within the WMMA. Federal lands within the WMMA are managed by the Bureau of Land Management (BLM). The WMMA includes Federal, State, and private lands in the western portion of San Bernardino County and the eastern portion of Kern County. The center of the study area is 20 miles northwest of Barstow, California (Figures 1 and 2).

Jan 1, 1993

By A. D. Hahn

This report describes reconnaissance by the Bureau of Mines of titanium-bearing beach sands on Ship Island in the Gulf of Mexico off the south coast of Harrison County, Miss. The purpose was to determine the ilmenite, rutile, and associated heavy-mineral content of black-sand-bearing beach sands. The investigation was part of a survey of titanium resources of the United States. Ilmenite (FeTi03), an iron-titanium oxide, is the major titanium-bearing mineral consumed in the titanium pigment industry. Rutile (TiO2), titanium dioxide, is used mainly as a constituent in welding-rod coatings and in producing titanium metal. The major fieldwork was conducted during the first half of February 1961. Nine holes, totaling 220 feet of bore, from which 110 samples Her taken, were drilled at widely spaced intervals on the island.

Jan 1, 1962

By H. B. Humphrey, F. E. Cash

The Birmingham coal-mining district of Alabama has many local physical conditions that contribute largely to the proble of preventing coalmine fatalities . Coal : nes of Alabama have been under the supervision of the State mine inspector since 1892 , and reports have been made with increasing completeness since that time . The U. S. Bureau of Mines has maintained a station of the safety division in the district since 1912 to cooperate with operators and the State in the advancement of safety in mining . A description of conditions in regard to fatal accidents as they have been and as they now are in Alabama , compared with the entire United States , will indicate the progress that has been made and that should still be made in reducing fatal mine accidents .

Sep 1, 1930

By M. R. Geer

The use of the cyclone as a dense-medium cleaning device was first described by Driessen6/ in 1945, after development of the process in the Netherlands during the German occupation of World War II. A pilot plant was built in the Netherlands soon thereafter, and the first commercial plant was built in 1948. By 1958, 18 plants were operating or under construction.7/ Thus, economic factors in Europe, where the high cost of coal places a premium on efficient cleaning, dictated rapid adoption of the cyclone. American reception of the process differed. The Bureau of Mines presented the results of its own small-scale cyclone experiments in 1946;8/ showing a sharp separation between coal and impurity; adoption by industry now is taking place. There is now much greater emphasis on the efficient cleaning of fine coal, and the first American cyclone plant has begun operating; others are planned or under construction. With the present interest in improved treatment of fine coal, the Bureau of Mines felt that additional performance data on the cyclone would be helpful to industry. Therefore, a complete, open-circuit pilot plant was built to make cleaning trials on American coals covering a wide range of washability characteristics. Five raw coals and one middling product were included in the investigation, and each was cleaned at several densities; 17 cleaning trials are reported.

Jan 1, 1961

By R. A. Guidotti

The Federal Bureau of Mines studied the thermal decomposition of the nitrides of the Group V A metals (CbN, Ta3N5, and VN) with the goal of preparing high-purity metals. Solid-state purification and arc and electron-beam melting were examined. Electron-beam melting proved to be the most efficient means of nitrogen and oxygen removal. Columbium and tantalum of 99.9-pct purity were prepared by this technique; in the case of vanadium, however, nitrogen could not be reduced below the solid-solution level.

Jan 1, 1976

By R. S. Warfield

Following World War II, the rapid increase in both military and civilian activity in the area served by the Alaska Railroad stimulated interest in the availability of local sources of nonmetallic minerals that might be used for building materials. Except for abundant sand and gravel and some pumice, the construction industry of the area depended entirely on high-cost imports for building materials of mineral origin. Because continued rapid growth was anticipated, development and use of local sources of such materials was advocated by both military and civil authorities to reduce the high costs of con¬struction and bolster the unstable economy of the area. The U.S. Department of the Interior began a program On included examining the numerous deposits of nonmetallic minerals accessible to the Alaska Railroad to determine their possible use as raw materials for the construction industry. Preliminary field investigations were made by the Geological Survey. The more promising deposits were subsequently examined and sampled by Bureau of Mines engineers, and the samples were subjected to the laboratory tests necessary to indicate the chemical and physical characteristics of the raw materials or their products. Such field and laboratory investigations were conducted on clay, shale, argillite, limestone, gypsum, and pumice taken from various parts of the area. In initial phasees of the work, done irate 1948 through 1952, many of the deposits examined were suitable for proctoring building materials. Results of the work completed during that period have been published in a Bureau of Mines report3 giving general information and detailed data on more than 35 deposits that were investigated.

Jan 1, 1962

By H. R. Appell

The Bureau of Mines studied the conversion of a variety of cellulosic wastes, for example, sawdust, bovine manure, sewage sludge, urban refuse (free of metal and ceramics), etc., to heavy oils. The objective of the investigation was to determine the scope of the reaction and elucidate the chemistry involved. The reactions took place in the presence of synthesis gas and water or carbon monoxide and water under conditions of elevated temperatures and pressures. Waste conversions above 90 pct, often near 99 pct, with oil yields in the range of 40 to 60 pct, were obtained in the temperature range of 250° to 425° C and pressure range of 1,500 to 4,000 psig. Because mild conditions were sought, most of the experiments were conducted at temperatures of 250° to 350° C and pressures of 1,500 to 3,000 psig. In general, lower viscosity products were obtained at higher reaction temperatures. Conversions and oil yields were significantly increased by operating in the presence of a high-boiling oil; either anthracene oil or oil recycled from the process was satisfactory. Synthesis gas containing 50 pct carbon monoxide gave satisfactory results as a replacement for carbon monoxide. Cobalt molybdate on alumina catalyst, used with sodium carbonate, gave a product of lower viscosity and lower oxygen content than sodium carbonate used as the sole catalyst. The waste-to-oil process has been successfully investigated in continuous flow equipment as well as in batch autoclaves.

Jan 1, 1975

By Phillip R. Moyle

In 1985 the U.S. Bureau of Mines evaluated the mineral resources of the Sheep Creek West Wilderness Study Area (ID-111-36A), Owyhee County, ID, for the U.S. Bureau of Land Management. The Wilderness Study Area consists of 11,680 acres centered approximately 20 miles south of Grasmere, 10. It contains no mines, claims, or prospects. No mineral resources were identified; however, a geode occurrence within and adjacent to the Wilderness Study Area, and minor amounts of placer gold along Sheep Creek, may be of interest to rorkhounds and recreational gold panners.

Jan 1, 1986

By G. E. McElroy

This report discusses the construction and use of an all-pressure psy- chrometric chart in which the requirements of simplicity of appearance and absolute accuracy have been waived, to a certain extent, to provide for the rapid determination of psychrometric data and for the rapid solution of air- conditioning problems of major interest to the mining industry. Many mines in which air-conditioning problems are important are situated at elevations far above sea level and embrace great differences in elevation - in excess of 8,000 feet in certain mines → throughout their airflow circuits. Under these conditions, the effects of variations in the pressure of the at- mosphere upon the physical properties of the mixture of air and water vapor of which it is composed are considerable and should be taken into account in the solution of problems. The simple types of psychrometric charts in common use, such as the Carrier, Bulkeley, Hill, and Goff (American Society of Heat- ing and Ventilating Engineers Guide), are not generally suitable, in that they are drawn for a single barometric pressure 29,92 inches mercury.

Dec 1, 1947

By M. J. Ankeny

Coal-mine haulage ranks second as a cause of coal-mine fatalities, and the prevention of such accidents will materially improve progress in safety in the coal-mining industry. Beginning March 1950, Federal coal-mine inspectors were made responsible for completely investigating all fatal accidents in and around coal mines. During these 10 months, Federal coal-mine inspectors investigated 447 fatal accidents. This is a study of 121 of the fatal haulage accidents investigated, which constituted 27 percent of fatalities from all causes. Haulage employees represent only 12 to 15 percent of mine personnel, but, on the basis of accident frequency, their work is the most hazardous in coal mines. Fatal haulage accidents occurred in 53 bituminous coal-producing counties representing 14 States and Alaska. The physical conditions represent a cross section of' producing coal beds. Mining and transportation methods vary, from those of small hand-loading mines to those of modern mechanized mines.

Jan 1, 1951

By Margaret R. Egan

The U.S. Bureau of Mines conducted experiments in the intermediate-scale fire tunnel to assess the influence of air velocity on the gas production and smoke characteristics during smoldering and flaming combustion of Pittsburgh seam coal and its impact on the detection of the combustion products. On-line determinations of mass and number of smoke particles, light transmission, and various gas concentrations were made. From these experimental values, generation rates, heat-release rates, production constants, particle sizes, obscuration rates, and optical densities were calculated. Ventilation has a direct effect on fire detection and development. The results indicate that, in general, increased air velocity lengthened the onset of smoke and flaming ignition, increased the fire intensity, but decreased the gas and smoke concentrations. Increased air velocity also lengthened the response times of all the fire sensors tested. Rapid and reliable detector response at this most crucial stage of fire development can increase the possibility that appropriate miner response (fire suppression tactics or evacuation) can be completed before toxic smoke spreads throughout the mine.

Jan 1, 2010

By M. A. Mahtab

This report describes the procedures used by the Bureau of Mines for obtaining attitudes of joints surveyed with a borescope in inclined boreholes. An algorithm for computing the dips and azimuths of the observed joints is presented. The algorithm is used to solve an example problem. A computer program based on the algorithm is listed. It is hoped that the procedures described here will be useful in treating large quantities of data obtained from comprehensive borehole surveys.

Jan 1, 1973

By Laxman S. Sundae

Laboratory tests were conducted at the U.S. Bureau of Mines to determine the effects of roof-bolt drilling parameters on penetration rate in sandstone using tungsten carbide alloy (WC-Co) and polycrystalline diamond compact (PDC) drill bits. During the tests, water pressure of 552 kPa was found to be adequate for removing the cuttings from the tops of drill holes. Test results show that for both types of bits, penetration rate increased when thrust was raised from 227 to 1,588 kg. When water pressure rose from 554± 120 to 1,344±350 kPa, the effect on penetration rate was not significantly different. Conventional WC-Co bits became dull when one or two holes were drilled, after which the penetration rate dropped dramatically. Microscopic examination shows that the cutting edges of PDC bits also become somewhat dull, but at a much lesser rate than WC-Co tips. Microscopic examination also reveals that the wear mechanism of WC-Co and PDC bits is quite different, which may explain the longer life of the PDC bits.

Jan 1, 2010

By D. K. Deardorff, Laurance L. Oden, H. Kato, M. I. Copeland

The equilibrium relationship of hafnium and tantalum was studied to facilitate alloy and property investigations . The data obtained are presented graphically as the equilibrium diagram . Alloys were prepared from high - purity components by nonconsumabletungsten- electrode arc melting . Data for the equilibrium diagram were obtained by optical pyrometry , metallography , X- ray diffraction of heat treated specimens , X- ray diffraction using a high- temperature camera , and differential thermal analysis . During the investigations , a casting apparatus was constructed , and the existing melting - point apparatus was improved . The bcc allotrope of hafnium forms a continuous series of solid solutions , called beta , with tantalum which exhibit a minimum melting point at 20 wt pct tantalum and 2,110 ° C. At 24 wt pct tantalum and 1,050 ° C , hafnium- rich beta decomposes in a monotectoid reaction to yield alpha and tantalum- rich beta . The monotectoid isotherm extends from 5.5 to 60 wt pct tantalum . The twophase region , in which hafnium- rich and tantalum- rich beta solid solutions are immiscible , rises to a maximum temperature of 1,265 ° C at 38 wt pct tantalum . The solubility of hafnium in tantalum decreases from 40 wt pct at the monotectoid temperature to 20 wt pct at 750 ° C.

Jan 1, 1964

By Albert W. Deurbrouck

The performance of four sand cones was evaluated by the Bureau of Mines in three preparation plants that utilized cones in various flow schemes. The cone at plant A was a simple two-product one that provided clean coal and refuse. Plant B had two cones; one cone made a primary separation and the other a secondary separation. The primary cone separated salable coal from heavy rejects. The secondary cone separated a low-ash metallurgical coal and an intermediate-ash product suitable for plant fuel or steam markets. In plant C the sand cone was equipped with a middlings draw Which continually removed an intermediate specific-gravity product below the surface of the cone. The three primary separations of raw coal effected between floats and sinks were excellent. The recovery efficiencies for the plus 1/4-inch material ranged from 99.8 to 97.6 percent, the error areas ranged from 19 to 23 square centimeters, and the probable errors in specific gravity ranged from 0.033 to 0.024. The performance data of the two secondary separations varied from excellent in plant B, where the separation was on a par with the primary separations, to somewhat inferior in plant C, where the secondary separation was effected at the middlings draw.

Jan 1, 1965