Search Documents

By C. J. Thompson

This Bureau of Mines study describes the preparation of sulfur compound concentrates boiling from 225° to 400° C, and reports the sulfur types detected in these concentrates by low-voltage mass spectrometry (LVMS). Existing LVMS methods were extended; the procedures described should be generally applicable to high-boiling petroleum distillates and concentrates as a preliminary means of narrowing the number of factions to be considered for more detailed separation and identification studies. The following major sulfur compound constituents of petroleum are indicated by the data: benzothiophenes, dibenzothiophenes, naphthanothiophenes, naphthenobenzothiophenes, and homologs and isomers of these. Cyclic and chain sulfides comprise a significant portion of the gas-oil range sulfur compound types. The presence of some classes of sulfur compounds containing two sulfur atoms per molecule was indicated.

Jan 1, 1966

By Albert J. Forney

Extensive studies have been made of the various effluents found in the Synthane coal-to-gas process. Analyses have been made of the waters, gases, and trace elements present in some of the streams. Results of analyses show the water effluents are the area where extensive research is needed.

Jan 1, 1974

By John K. Alley

Fibrous silicon carbide was produced by thermal decomposition of certain silicates contained in graphite crucibles. Induction heating was used to produce the necessary temperature and thermal gradients. Both green and white fibers were mainly the beta modification even though each color grew within a different temperature zone. Alpha silicon carbide, present in insufficient amounts for X-ray detection, was identified by electron diffraction. The white fibers formed in a zone between 1,365° and 1,634° C (±50° C). The green fibers (less contaminated) formed in a much more narrow zone between 1,650° and 1,672° C (±50° C). The average lengths and widths of microscopic fibers grown by this method were 1.5 mm/0.002 mm (white) and 1.2 mm/0.0035 mm (green); however, same fibers observed by electron microscope had cross-sectional measurements of 150 to 300 A. Both differential thermal analysis and thermogravimetric analysis showed that silicon carbide fibers oxidized in air at temperatures above 500° C. Fibrous silicon carbide was indexed as a cubic cell with the dimensions a = 4.358 A. The density calculated from X-ray data was 3.217 g/cm3.

Jan 1, 1963

By Joe H. Skidmore

This paper, describing mining and milling methods and costs at the Gold Hill mine, is one of a series being published by the Bureau of Mines. Boise Basin, in which the geld Hill mine is located, is in the central part of Boise County, Idaho, about 30 miles by air line northeast of Boise. The mine, owned and operated by Talache Mines, Inc., is at the southern end of the town of Quartzburg. About 115 to 125 tons daily is mind by square-setting and is treated in an amalgamation plant.

Jan 1, 1938

By E. C. Perkins

The purpose of the research described in this report was to develop techniques for using ilmenite from domestic deposits for the production of titanium tetrachloride. The research was done by the Federal Bureau of Mines in cooperation with the General Services Administration under contract DMP-116, Utilization of Domestic Ilmenite. Bench-scale continuous chlorination of an Idaho ilmenite containing 27.9 percent titanium and 35.6 percent iron yielded a crude titanium tetrachloride suitable for purification and for the production of titanium metal and pigment. A summary of the results of 380 hours of operation showed that 82.4 percent of the titanium was chlorinated, with 92.5 percent utilization of chlorine. The construction- of a. quartz tube chlorinator 4-inches in diameter and 24 inches long is described with the necessary details of operation.

Jan 1, 1961

By David F. Smith

[The U. S. Bureau of Mines at its Pittsburgh Experiment Station is frequently called upon to determine by laboratory tests the explosibility of suspensions in air of various dusts encountered in mines and elsewhere. Not all dusts which are combustible or contain combustible material will form explosive mixtures with air under ordinary conditions of temperature and pressure. They may not be highly combustible enough. They may contain a considerable amount of inert or non-combustible material or, the dust particles may not, be fine enough to form explosive mixtures. A knowledge off the chemical composition of a dust together with a determination of the size of the particles often gives valuable indications. But in many cases actual explosibility tests are necessary. Such a case is evidently that of powdered soap, whose explosibility hazard the Bureau was recently called upon to determine, Although an explosion which occurred in a soap plant as early as 1890 was attributed4 to powdered soap, it is apparent, due to the great number of inquiries received by the Bureau, that the hazard presented by powdered soap has not been at all generally appreciated. To the writers' knowledge, no extensive investigation of the explosibility of powdered soaps has been made. It is only recently that pure powdered soap has been manufactured on a large scale. The familiar "soap powder" in the past was usually a mixture of soap with a relatively large quantity of sodium carbonate. Often it contained large amounts of moisture and abrasive material. Even a highly combustible dust when mixed with large quantities of inert dust will not form explosive mixtures with air. Pure powdered soap, however, presents a different aspect. Pure soap is formed by combination of alkali (incombustible material) with fatty acid (combustible material). Toilet soap fray also contain a certain amount of glycerin and essential oil winch, being combustible influence the explosibility]

Jan 1, 1928

By J. B. Zink, M. J. Peterson

A semiquantitative spectrochemical method was developed and applied to the analysis of ash of U.S. coals . A low- temperature ashing procedure was used to minimize the loss of volatile elements . The analytical procedure provides for the estimation of 68 elements including major , minor , and trace constituents . Standards for the trace elements were prepared in a synthetic base mixture that approximates the average composition of U.S. coal ashes . Excitation was achieved with a d- c arc , spectra were recorded photographically , and interpretation was made by visual comparison of spectra of unknowns with spectra of graded standards series . Thirty- six trace elements were found in the analysis of 900 samples . Details of the procedure are presented , including sample and standards preparation , excitation and exposure conditions , spectral lines used , and approximate limits of detectability .

Jan 1, 1964

By Don M. Coulter

"INTRODUCTION The district comprising Union, Lafayette, Pontotoc and Calhoun Counties, Miss. (fig. 1), was examined in October 1941 by R. W. Smith of the Bureau of Mines, accompanied by J. W. Adams of the Mississippi Bauxite Co. 3/ Subsequently, geologists of the Federal Geological Survey made a more detailed study of the area. 4/Bauxite had been reported as present in several localities in Pontot. County, and large deposits of kaolin are known in Pontotoc, Union, Calhoun, and Lafayette Counties. Many of the bauxite deposits, such as those on Big Hill, Second Hill, and Third Hill, in Pontotoc County, form the caps on hills and are outliers of Wilcox deposits on the Midway formation. Such deposits could have no extensions because of erosion and were not examined, as they were investigated by the Mississippi Geological Survey. 5/ Most of the bauxite was known to be low-grade, with a high iron content. However, Pontotoc County in particular presented possibilities of finding high-grade bauxite with a low iron content by drilling down the dip from the Wilcox-Midway contact. Consequently, with few exceptions the investigation was confined to drilling in this direction.Headquarters were established in Tupelo, Miss., on July 13, 1943, and mineral agreements were obtained covering 8,367 acres of land, with 62 land-owners in Pontotoc and Union Counties. Holes were drilled on properties of three of the landowners in Union County and 36 in Pontotoc County."

Apr 1, 1948

By John O. Atkins

[Experiments were conducted by the Bureau of Mines on five types of simuated lunar rock (dacite, tholeiitic basalt, vesicular basalt, pumice, and uluth Gabbro) to study the effects of various simulated lunar environments n their strength and deformational properties. Specimens were tested in an ltrahigh vacuum (UHV) system at pressures ranging from atmospheric down to 0-11 torr and at temperatures of -130°, 20°, and 135° C. All tests were onducted with a servocontrolled testing machine. Rock specimens tested at 0° C in UHV exhibited significantly higher compressive strength and Young's odulus than those tested at 20° C in atmospheric pressure. The magnitudes f increase are related to the porosities and permeabilities of the rock pecimens; high porosity and permeability allow better outgassing and thus nprove surface cleanliness in UHV. The compressive strength generally ncreases but Young's modulus decreases as test environments change from 20° C i UHV to 135° C in UHV. No significant difference was observed in the iysical properties measured at 20° C in LTV and -130° C in UHV. Anisotropy i strength and Young's modulus exist both in UHV and at atmospheric condi¬'.ons with the same symmetry pattern. The orientations of the principal axes iy, however, change from the atmospheric to UHV condition. The results idicate that rock fragmentation in lunar environment will require more ergy than that at 20° C in atomospheric pressure.]

Jan 1, 1974

By Robert C. Ellman

Stockpiles containing 2.3 million tons of lignite constructed in the period 1948-56 in conjunction with the construction of Garrison Dam on the Missouri River demonstrate successful stable long-term storage of lignite. Uniform and thorough compaction of each of the I-foot-thick layers by which the piles were constructed produced a bulk density of 70 Ib/cu ft. Air penetration into the stockpiles was restricted to a degree that prevents spontaneous heating or deterioration of the stored lignite, A continuing record of observations beginning with stockpiling operations in 1948 has been accumulated, This includes periodic fuel analysis, analysis of pile gases, and measurement of pile temperatures on the first large stock-pile, pile 5. This report describes the stockpiling method, the changes in heating value, pile gas composition, and pile temperature and summarizes observations from 1953 to 1964, Data accumulated attest to the stability of the stored lignite. The variation of the average heating value of periodic pile-depth samples is only 160 Btu/lb (11,990 to 11,830) on the moisture" and ash-free (maf) basis during almost 10 years of storage. Temperature levels of the pile interior are progressively decreasing. At pile surface, cyclic variations occur with the season. The only problem encountered with the large stockpiles is wind and water erosion of the pile surface. The partially successful control measures used are described.

Jan 1, 1967

By R. Barany

Thermodynamic calculations pertaining to the minerals gibbsite, kaolinite, halloysite, and dickite have been hampered by the lack of adequate heat and free energy of formation data. Previous data for gibbsite were highly uncertain, and there were no data for the other three substances. By use of hydrofluoric acid solution calorimetry, the Bureau of Mines derived heat of formation values from the elements and from the oxides for the four substances, and the data were combined with known entropy values to obtain the corresponding free energies of formation. The results show that gibbsite and halloysite are thermodynamically unstable with respect to the oxides (a- alumina, a- quartz, and liquid water) at 298.15° K,, while kaolinite and dickite are only moderately stable (to about the same degree), The instability of halloysite, in comparison with kaolinite and dickite, results in a 60°-lower equilibrium decomposition temperature.

Jan 1, 1961

By G. R. Hopkins

"The average heat requirement per barrel of crude refined in the United States rose from 579,000 B. t. u. in 1940 to 584,000 B. t. u. in 1941. This marked the second successive year in which there was an apparent loss in fuel efficiency at refineries. This ""loss"" took place despite an increase in crude runs, which used to be an invariable indicator of a lower average.Probably the chief factor in the increased heat requirement in 1941 was the gain in the over-all gasoline yield from 43.1 percent in 1940 to 44.2 percent in 1941. Possibly another important factor was the further use of obsolete equipment to increase throughput.The refiners used more of all kinds of fuel excapt coke in 1941 than in 1940. However, the only fuels which increased materially in relative importance were refinery gas, which contributed 51.6 percent of the total heat units in 1941 compared with 50.7 percent in 1940, and natural gas, the share of which rose from 17.1 percent in 1940 to 18.0 percent in 1941. The changes in the percentages for the other fuels were as follows: Oil decreased from 25.7 to 24.1 percent; acid sludge fell from 2.7 to 2.5; coal remained at 3.4 percent; and coke (including steam) fell from 0.5 to 0.4 percent.New records for fuel efficiency were set in all three of the districts east of the Mississippi, namely, East Coast, Appalachian, and Indiana, Illi¬nois, etc. All the ether districts reported higher average fuel requirements in 1941, except the Louisiana Gulf and Arkansas-Louisiana inland.Since the year of the first statistics, the refiners have steadily increased their purchases of electricity. In 1941 total purchases were 1,862,996,000 kilowatt-hours, or 11 percent more than in 1940."

Apr 1, 1943

By Michael S. Wieland

This report investigates whether it is tractable and thereupon reasonable to remove the booster influences when ranking the toxic fumes of non-cap-sensitive mining explosives. The hazard potential is represented by relative fume toxicity RFT, the resultant influence computed from a formulated rule with a restricted set (tally) of fume components and multiplying constants. The RFT result is compared to the rule criterion that represents the worst case tolerable toxicity stipulated by regulations or otherwise. The typical nonstoichiometric booster composition can render notable unwanted influence on the RFT ranking results. Historically, the remedy was to shoot the booster separately and reduce the trial concentrations by the relevant subtractions. Unreal negative concentration results were noted on rare occasions, revealing the faulty nature of the reduction procedure. With thermodynamic reaction chemistry codes TDRC, on the other hand, the booster ingredients can be retained in or removed from the reactant tabulation, yielding reduction factors taken as the concentration ratios for the two circumstances. The underlying presumption regarding reduction factors is that the ratios of component concentrations with and without the booster ingredients when resolved theoretically ought to equal those rendered experimentally, when tractable. Upon rearranging the presumed relationship, the unadjusted fume concentrations divided by theoretical reduction factors yield the wanted readjusted fume concentrations, thereby removing the booster influence without generating unreal negative concentrations. The work principle from thermodynamics restricted by the constraint of zero-net interaction loss is utilized in conjunction with the TDRC to resolve the wanted (Z-state) fume spectrum. This circumvents the recognized difficulty with traditional hydrodynamic detonation theory that is related to the nonideal reaction characteristics of typical mining explosives. The tacit characteristic of the Z-state resolved from the non-trajectory work principle is that it can not be remedied or tampered with, unlike the traditional trajectory techniques where the reaction products can be readjusted by changing formula representations, nullifying specific reactions or otherwise manipulating the thermodynamic trajectory process. Though the work principle theory is an unfinished formulation, the Z-state results prove worthy enough for rendering trends and comparisons and reaching otherwise useful conclusions. Further refinements should yield more reliable fume spectra and indicate explosive composition readjustments that would reduce toxic effects within underground mines and the wider world environment.

By G. M. Potter, J. B. Rosenbaum, Masami Hayashi

Most Japanese copper smelters are located in areas of concentrated industrial activity and high levels of atmospheric pollution. A review of unofficial sulfur dioxide emission control data from major Japanese smelters shows capture of 91 to 99.7 percent of the sulfur in the smelter feed. The bulk of Japanese smel ting capacity was constructed in the last 10 years. Six of the major sme lters use flash furnaces, and two use reverberatory furnaces. A prototype three-furnace continuous system is in use as a parallel train with reverberatory furnaces at one smelter. Most of the sulfur dioxide is manufactured into sulfuric acid. The remainder is captured by gas scrubbers that yield gypsum and sodium salts. Ready markets exist in Japan for the acid and other su lfur byproduc ts.

Jan 1, 1967

By F. D. DeVaney

[In the course of the investigation by the U. S. Bureau of Mines and the Missouri School of Mines and Metallurgy at the Mississippi Valley experiment Station at Rolla, Mo., on the beneficiation of the low-grade manganese ores of the country, some samples from the Cuyuna District, Minn., have been examined. The work was done under the direction of W. H. Coghill, supervising engineer of the Mississippi Valley Experiment Station. Josoph and Kinney5 in venting about the relative importance of Minnesota deposits of low-grade ore compared to the total reserves say:]

Jan 1, 1930

By R. E. Meaker

Electrical conductivities and densities of molten fluoride systems were measured as functions of the melt temperature and composition. For any given mixture, the two properties change linearly with temperature. Three alkali metal fluorides were selected as solvents for melts of the type LiF-, NaF-, and KF-MFx, where M is a metal selected from the alkali metal or alkaline earth groups, or from the lanthanide or actinide series of elements, and x = 1-4. Heats of activation for conductance were calculated from the experimental data and varied from 2.3 to 9.2 kcal/mole at 1,000° C. Some relation between position in the phase diagram and the conductivity changes was suggested.

Jan 1, 1971

By A. R. Mumford

During the course of an investigation conducted by the fuel section of the Bureau of Mines , on a hand- fired return- tubular boiler plant , it was found that the average cost of fuel to produce 1,000 lb. of steam was $ 0.5287 . Tests conducted after some simple changes had been made in the furnaces , and in the control of the boilers , showed the previous high cost of fuel per 1,000 lb. of steam could be reduced to the reasonable figure of $0.3540 , or the equivalent of over 30 per cent saving in fuel cost .

Mar 1, 1923

By I. L. Feld

This report describes an attrition-grinding process and equipment for grinding coarse kaolins to the 2-micron particle-size range. The research was undertaken by the Bureau of Mines to devise an acceptable method for converting coarse kaolins, such as paper-filler-grade clays, to paper-coating-grade clays, thereby increasing the value and extending the life of the southeastern paper-clay deposits. The attrition-grinding process is basically the intense agitation of a slurry composed of the material to be ground, a granular grinding medium, and a suspending fluid. This process gave better particle-size reduction than that obtained by several other grinding methods. Results of batch tests in 5-and 10-inch-diameter attrition grinders demonstrated that a coarse kaolin containing about 13 percent minus 2-micron, equivalent spherical diameter (e.s.d.) particles was readily ground to give a product with 88 percent minus 2-micron e.s.d. material. Power consumption was reasonable in view of the increased value of the ground material. Comparison of particle-size reduction with power-consumption data for the two units indicated that better performance was obtained with the larger machine.

Jan 1, 1960

By R. Karl Zipf

This report presents nearly all structural data available from explosion tests of 20-psi mine ventilation seals and concrete-block ventilation stoppings that were conducted by the National Institute for Occupational Safety and Health during 1997?2008. Although the seals tested were designed to meet the former federal 20-psi pressure design standard, the structural information contained herein on these seal tests will facilitate the analysis and design of coal mine seals that meet the new explosion pressure design criteria of 50 and 120 psi as set forth in the Mine Safety and Health Administration (MSHA)?s final rule on ?Sealing of Abandoned Areas.? The seal testing data are organized into six broad categories of seal structures based on the materials used and the construction method for those 20-psi seals: 1. Concretelike materials with steel reinforcement and reinforcement bar anchorage to rock 2. Pumpable cementitious materials of varying compressive strengths with no steel reinforcement and no hitching 3. Articulated structures such as solid-concrete-block seals and ventilation stoppings made of solid and hollow-core concrete blocks 4. Polymer and aggregate materials without hitching 5. Wood-crib-block seals with or without hitching 6. Articulated structures such as lightweight blocks with or without hitching This summary contains data on 52 different structures in the above categories?44 seals and 8 ventilation stoppings. The structural data sets include the applied loading on the tested seal represented by a pressure-time curve and, when available, the measured seal response represented by a displacement-time curve. The structural data sets enable the calibration and verification of numerical models of seal behavior at the 20-psi level, which may then facilitate future structural analyses of seal designs for the new 50- and 120-psi explosion pressure design criteria.

Aug 1, 2008

By E. C. Lane

The motor gasoline which is being marketed in the United States this summer is apparently more volatile than the gasoline sold a year ago. In fact the average volatility of this summer's gasoline is almost the same as the average volatility of the gasoline marketed last winter. During the past seven years the Bureau of Mines has made semi-annual surveys of the gasoline marketed in the United States, the survey just completed being the fourteenth in the series. The cities in which samples have been collected have been chosen as representative of the more important marketing territories as it is obviously impracticable to obtain a sample of every gasoline sold in the entire country.

Jan 1, 1926