Search Documents

By Michael Sokaski

A dense-medium cyclone pilot plant was built to clean 112-inch to 0 size coal. This pilot plant does not require the removal of the extremely fine material (usually minus 1/2-mm) from the feed, which is necessary in conventional dense-medium cyclone plants. The essential difference between conventional cyclone plants and the pilot plant is in the medium-recovery system. The latter uses a combination of sieve bend screens, classifying cones, and magnetic separators for medium recovery. Eight tests were run in the pilot plant at a feed rate of 5 tons per hour with four different raw coals and one crushed jig middling product. Sharp separations were obtained as indicated by an average error area of 27 and probable error of 0.047 for the 112-inch to 200-mesh size range. Magnetite loss averaged about 2.5 pounds per ton of feed. The influence of several factors on cleaning performance of the cyclone was investigated. The diameters of both the overflow and underflow orifices were found to be important for optimum cleaning performance, but these diameters could vary over a wide range without serious effect; however, if this range was exceeded, cleaning performance deteriorated. Better cleaning performance was obtained when the cyclone inlet pressure was increased from 9 psig to 13 psig. The size of the magnetite particles in the medium was found to have a substantial effect, and the best cleaning results were obtained with grade B magnetite. Demagnetizing the magnetite in an effort to decrease the effective particle size did not improve cyclone performance.

Jan 1, 1963

By K. C. Dean

The combination of flotation and chemical processing methods presented in this report of the Bureau of Mines enabled treatment of typical low-grade ferberite ores from the Boulder County, Colo. area, to produce specification-grade synthetic scheelite. The overall recovery from ore to synthetic scheelite was 87 percent, based on a flotation recovery of 93 percent and a similar recovery in chemical processing. Preliminary mineral dressing studies revealed that the physical and mineralogical nature of typical ferberite ores precluded high recovery of tungsten in plus 60-percent-W03-grade products by these methods. Therefore, the flotation research was focused on attaining plus 90-percent recovery in a concentrate containing 10 percent W03. Detailed studies were made (1) to establish optimum grinding conditions for obtaining adequate mineral liberation, (2) to develop collecting and modifying reagent combinations that would enable controllable selective flotation, and (3) to define the influence of different pulp solids, temperature, pH, and time for conditioning and for the rougher and cleaner flotation stages.

Jan 1, 1961

By E. A. Rowe, G. H. Keith, B. D. Jones

An evaluation of electrowon tungsten powder was made by comparing its characteristics with conventional hydrogen - reduced tungsten powder . Electrowon tungsten powder was investigated with respect to particle size and shape , apparent density , flow rate , compressibility , green strength , and sintering characteristics . In addition , its chemical purity , absolute density , and purification by melting were determined . Significant findings were higher flow rates and better compressibility than hydrogen - reduced tungsten powder . However , the large particle size peculiar to the electrowinning process effectively prevented conventional sintering to a high- density material . The possibility of producing high - density material , using a new technique of hot swaging sheathed sintered - tungsten compacts , was demonstrated by the achievement of densities of 92 percent of theoretical .

Jan 1, 1965

By J. D. Zetterstrom

This report supplements an earlier publication on lightweight aggregates of North and South Dakota.3/ The purpose of the investigation was (1) to study the expansion characteristics of large samples of Dakota clays and shales in a 12-inch by 15-foot rotary kiln; and (2) to improve the laboratory bloating test as a tool for predicting the suitability of samples for the rotary-kiln process. This was done by comparing results of the laboratory and kiln tests.

Jan 1, 1956

By J. J. Jakosky

"This report is the second of a series dealing with electrical methods of underground communication nd signalling, and is a discussion of some of the factors involved in -applying radio in mines.A previous report2 described the results obtained by the use of the ""T.P.S."" of ground-conduction method of signalling, and outlined in a general way the requirements for a practical mine communication apparatus.The popularity of radio, the development work on new apparatus, a desire to render humanitarian service to entombed miners, and an endeavor to find new uses and applications for radio stimulated many persons to attempt the application of radio to mine rescue purposes. A number of experiments on underground reception from surface broadcast stations have been conducted by different experimenters in various parts of the country and the widespread interest in the subject is shown by the fact that these tests have been con¬ducted in many States, The Bureau of Mines has received information regarding, underground tests in Illinois, Pennsylvania, Arizona, Utah, Idaho, Colorado, Michigan, Wyoming, Kentucky, New York, Connecticut, and in England, Germany, Italy, and Franc.From occasional press notices and illustrations in different papers it may appear that radio communication in mines and in tunnels being excavated is en established fact, and that the method is comparatively simple. As a matter of fact the reverse is the case."

Apr 1, 1924

By P. C. McWilliams

The Bureau of Mines investigated ground support problems in four major block-cave mines to assess the current "state-of-the-art" and to delineate areas for future research. The most significant problem is the inability of present support systems to hold moving ground. Further, as mining progresses to greater depth, this problem becomes more serious. Providing adequate temporary support capable of withstanding primary and secondary blasting is the next most significant problem. A detailed analysis of the effect of mining methods on support problems is also recommended for future research.

Jan 1, 1975

By Larry L. Anderson

Enormous quantities of organic wastes are produced each year in the United States. The total amount is in excess of 2 billion tons and at least 880 million tons of this is moisture- and ash-free organic material (dry organic solids), representing a potential energy source of significant magnitude that is not being utilized. Bureau of Mines scientists have developed methods for converting these wastes to convenient energy forms. This report itemizes and evaluates for the first time in detail the quantities and sources of moisture- and ash-free organic material contained in manure, urban refuse, industrial wastes, sewage solids, and agricultural wastes in the United States. Furthermore, estimates are presented for amounts of organic wastes collected or concentrated. The potential for fuel, either oil or gas, from both the total organic wastes generated and those collected or concentrated is also estimated.

Jan 1, 1972

By D. H. Desy

The Bureau of Mines studied the properties of copper that had been oxide dispersion-strengthened with 2 vol pct of either yttria or alumina. Compounds of copper and aluminum or yttrium, coprecipitated from aqueous solution, were converted to oxides; the copper was reduced, compacted, sintered, and extruded. For the resulting copper-dispersoid composites, room temperature tensile properties after annealing in hydrogen, elevated temperature tensile and stress-rupture properties, and electrical conductivity were determined. Compared with oxygen-free copper, copper-2 vol pct alumina or yttria had improved strength after annealing between 400° and 1,000° C, and improved elevated temperature strength, with little loss in electrical conductivity.

Jan 1, 1969

By A. J. Leighton

An improved mathematical model with the attendant computer program to calculate multiphase fluid flow in petroleum reservoirs is presented. The model is used to simulate the behavior when a fluid is used to displace hydro-carbon fluids in a reservoir. The method is an expansion of a previously published method, in Bureau of Mines RI 7011, but handles constant injection rate as an alternative to constant pressure. Program documentation is provided along with thorough explanations of the added program features. Using the program, the petroleum engineer can calculate oil recoveries for different flood patterns and operating conditions and select the conditions most likely to optimize recovery. Experience with the previous model demonstrated the need for the improvements in order to simulate reservoir behavior more accurately. The improved method will result in improved oil recovery. In this paper, the significant improvements are described in detail so that anyone interested can put the program to use.

Jan 1, 1975

By J. B. Salsman

As part of the research effort on investigating the effects of microwave energy on the chemical and physical properties of minerals and ores, the U.S. Bureau of Mines (USBM) Tuscaloosa Research Center has conducted research to measure the dielectric properties of these materials. The objective was to establish a reliable database for use in predicting the effects of microwave heating on a wide range of minerals. The dielectric constants and loss factors of minerals, commonly referred to as the dielectric properties, were determined utilizing the theory of microwave propagation through an open-ended, air-filled coaxial line that was terminated at its open end with the particular mineral under investigation. In this phase of microwave research, the USBM measured the dielectric properties of powdered minerals with medium to high electrical conductivities in the frequency range of 300 MHz to 3 GHz and as a function of temperature from 25 to 325 °C. Since the minerals were prepared as powders, techniques were used to relate the measured dielectric properties of the powdered minerals to the dielectric properties of the mineral at its theoretical or natural density.

Jan 1, 2010

By E. G. King

Strontium sulfide and barium sulfide occur as intermediates in commercial treatments of the impure natural sulfates to produce pure strontium and barium chemicals. Thermodynamic considerations involving these sulfides have been hampered by lack of basic data, such as the entropies at 298.15°K. This paper reports the results of heat capacity measurements of strontium sulfide and barium sulfide in the temperature range 50°-298°K. The entropies at 298.15°K. were derived from the heat capacity values. Free energies of formation at 298.15°k. were computed from the entropies and literature values of the heats of formation. Strontium sulfide and barium sulfide are thermo-dynamically less stable than calcium sulfide, but more stable than magnesium sulfide.

Jan 1, 1960

By P. E. King

The U.S. Bureau of Mines is conducting an ongoing research project to better understand the phenomena involved within electric arcs utilized in electric furnace steelmaking. With a better understanding of the physical and electrical characteristics involved, dynamic or predictive control of electric arc furnaces may be possible. A mathematical model is presented, but not solved, and the system of coupled equations is analyzed. Characteristic parameters are used to determine relative importance. In this manner, significant quantities are dermed. The parameters found to contribute little to the system of equations of motion are ignored. A resultant simplified system is identified, and directions for further study are indicated toward control of electric arc furnaces.

Jan 1, 1990

By L. H. Adami, E. G. King

The heats of formation of four sulfides --MnS ( alabandite ) , FeS ( hexagonal pyrrhotite ) , ZnS ( wurtzite ) , and CdS ( greenockite ) -- were determined by hydrochloric acid solution calorimetry . The heats of formation from the metals and rhombic sulfur at 298.15 ° K are , respectively , -51.01 ± 0.19 , -23.81 ± 0.24 , -45.86 ± 0.20 , and -35.70 ± 0.30 kcal /mole . The corresponding free energies of formation were calculated from the heats of formation and the pertinent entropy values .

Jan 1, 1964

By W. E. Wallace, S. -G. Xing, M. J. Keane, J. C. Harrison

"SummaryDiesel-exhaust particles from two sources were dispersed in aqueous mixtures of dipalmitoyl phosphatidyl choline, a major component of pulmonary surfactant, and were tested for genotoxicity. Diesel samples from the same sources were extracted with dichloromethane and transferred into dimethyl sulfoxide and subjected to the same assays. Both types of extractions yielded similar results in both the Salmonella mutagenicity assay and the sister-chromatid exchange assay using V79 cells. After separation of the samples into supernatant and sediment fractions, the activity of both diesel samples was shown to reside exclusively in the supernatant fraction for the solvent-extracted samples, and exclusively in the sedimented fraction for surfactant dispersed samples. These findings indicate that genotoxic activity associated with diesel particles inhaled into the lung may be made bioavailable by virtue of the solubilization / dispersion properties of pulmonary surfactant components.While diesel engine emissions are associated primarily with transportation, they are also very common in the workplace. Estimates for the U.S. are that as many as 1.35 million workers in as many as 80 000 workplaces are exposed to the combustion products of diesel engines (NIOSH, 1988). These occupations include, but are not limited to mining, agriculture, motor vehicle maintenance, fork lift truck driving, truck driving, and tunnel and bridge operation."

Mar 1, 1992

By O. P. Hood

The spontaneous combustion of coal lies at the bottom of the subject of storage. It is useless to store coal that is to be lost by fire from spontaneous combustion. Every engineer is familiar with the phenomena of the self-heating of coal, yet, for all that, spontaneous combustion is relatively rare. If we counted the times a portion of cod was stored where it would be undisturbed for a few weeks, the number of such storage operations in any one year would mount into the millions. Of these, a relatively small number show the phenomena of spontaneous combustion and time risk per ton is very small. It is extremely rare that in the smaller operations involving; only a few tons there is any heating. There is no spontaneous combustion of anthracite, and very rarely does the domestic consumer of bituminous coal find troublesome heating. The main interest in the subject lies in the large piles needed as reserves for public-service utilities, and the industries. Everyone desires to have directions for storage that are perfectly simple and yet will insure against loss. Unfortunately, the problem is too complicated for a simple solution. Many of the factors involved are difficult to determine, as we have no practical means of quantitative measurement. The factors involve chemistry, physics, and engineering, and the man who is

Jan 1, 1939

By A. Wahab Khair, Richard D. Begley

"This paper presents results of destructive tests performed on rectangular coal specimen under the influence of two vertical and simultaneous wedge indentation forces. Several wedge designs and spacings were utilized in compression tests. The objective of these experiments was to qualitatively monitor the effect of different wedge designs and spacings on the stress distribution within the coal specimen.Coal samples from the Waynesburg coal seam were cut and trimmed to cubical dimensions of approximately 5 X 10 X 20 cm. These specimen were subjected to parallel compressive forces through two vertically applied wedge indentors. Loading was achieved with a hydraulic hand pump in order to facilitate interferogram construction. The load increments were limited due to the sensitivity of the holographic interferometric technique (holometry) in measuring small displacements; therefore, interferograms were taken only during similar increments in order to allow for a qualitative comparison between different wedge design and spacings. In some cases, interferograms were taken immediately before and after failure of the specimen.Introduction Failure Modes Three distinct modes of failure occur when geologic materials are subjected to wedge indentation forces. As shown in Figure 1, a crushed zone is located immediately adjacent to the indentor while chipping can occur if the fractures initiated in the crushed zone extend upwards to the free surface.. The third failure mode is a zone of intricate frac¬tures located between the crushed zone and the chipping zone. Several experiments have been conducted over the years to better understand crater formation and stress distribution within geologic materials under the influence of an indentor. Generally speaking, crack initiation and propogation observed in these experi¬ments correlate fairly well with wedge indentation theory; however, the nature of the .fractures is greatly influenced by different material properties such as grain size and cleavage planes. In other words, a wide range of behavior has been found in different rocks subjected to wedge penetration. For example, it has been observed that some rocks are merely crushed and indented while others are more prone to cracking and chip formation. Therefore, the development or nondevelopment of chips depends mostly on wedge geometry, rock type and depth of penetration. This work is part of the study associated with opti¬mization of cutting parameters, which is best modeled by using brittle materials and subjecting them to rigid wedge penetration tests."

Jun 1, 1988

By F. P. Haver

Because State and Federal agencies have limited the amount of sulfur oxides that can be discharged to the atmosphere, most copper smelters plan to convert the S02 in offgases to sulfuric acid. In some cases, however, it might be preferable to use a nonsmelting method to fix the sulfur in the form of a discardable product. Research by the Federal Bureau of Mines has shown that sulfur in copper concentrate can be converted into insoluble anhydrite (CaS04) by roasting the concentrate with lime (CaO). After leaching the calcine to recover metal values, the residue may be discarded without harm to the environment. The process can use a rougher flotation product, thus reducing separation costs and saving valuable minerals (for example, molybdenite) that are now lost in making cleaner concentrate. In tests, rougher concentrate was pelletized with the theoretical amount of lime and roasted for 1 hour in a 6-1/2-inch-ID by 11-foot-long rotary kiln at 700° C. Sulfur retention was about 97 percent. Leaching the calcine with 20 percent RCI extracted approximately 99 percent of the copper, 73 percent of the iron, and 91 percent of the molybdenum. After the molybdenum was removed from the leach solution by adsorption on activated carbon, copper with a purity in excess of 99 percent was obtained by cementation on sponge iron. The strip solution then could be spray-roasted at 500° C to recover the RCI for recycle and obtain F2O3 as a byproduct.

Jan 1, 1975

The Bureau of Mines Minerals Information organization collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. This data collection activity was instituted by the 47th Congress in an appropriations act of August 7. 1882 (22 Stat. 329), to place the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines Minerals Information activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1985

By Arnold B. Hubbard

This report describes a method of concentrating the insoluble organic material (kerogen) in a rich Colorado oil shale without any apparent alteration of its original chemical form. The method involved treating finely pulverized shale with dilute acetic acid at room temperature to remove the carbonates, which act as a cementing agent for the shale, and cause the shale particles to partly disintegrate into the organic and inorganic components. The acid-treated shale then was centrifuged in different liquid mediums ranging from 1.4 to 1.15 gravity to effect a mechanical separation. From a Colorado oil shale containing 48.0 percent ash, kerogen concentrates containing 43.3 to 8.7 percent ash were obtained. The carbon:hydrogen ratios of the kerogen in the original shale and the different concentrates were essentially the same. The oil:kerogen ratios calculated from Fischer assays of the above samples were essentially the same, regardless of the organic or inorganic contents. This was also true of the assay water:kerogen ratios of the same samples. These data indicate that no significant change occurred in the kerogen during the concentration process.

Jan 1, 1952

By R. R. Brown

The solubility and the activity of aluminum chloride hexahydrate, A1C13?6H2O, in aqueous solutions were determined as a part of the Bureau of Mines, U.S. Department of the Interior, research to improve mineral processing technology for recovering alumina from low-grade domestic resources. The solubility of A1C13 in pure water was found to be 31.09 and 31.77 wt-pct at 25° and 85° C, respectively, and decreased drastically to 10 and 0.1 wt-pct when the respective amounts of 20.3 and 37 wt-pct hydrochloric acid (HCI) were added in solution. The equilibrium constant for the solubility of hexahydrate, activities, and activity coefficients of A1C13 and H2O were calculated and compared with the results from the available methods of estimation. The results were shown to be useful in leaching nonbauxitic ores for extraction of alumina by changing the solubilities of component salts upon addition of HC1. Simultaneous solubilities of A1C13, FeC13, KC1, and NaC1 in solutions of HC1-H2O were also determined and their effects on the purity of A1C13?6H20 crystallized from mixed salt solutions are briefly discussed.

Jan 1, 1979