Search Documents

By Thomas J. Peters

In 1988, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 34,310-acre Diablo Mountain (Additional) study area (OR-001-058), in order to evaluate its identified mineral resources and occurrences. The study area lies along the east shore of saline Summer Lake in Lake County, OR, about 145 miles southeast of Bend and 45 miles northwest of Lakeview. The climate is semiarid and temperate, and the study area is almost treeless. Geologically, the (Additional) study area is in a region of fault block-formed mountains and basins, characterized by interior drainage. The area is mainly underlain by unconsolidated Quaternary and Pleistocene lake and playa sediments, which may include subsurface evaporite mineral deposits and resources. Near the center of the eastern margin of the study area are an occurrence of dolomitic limestone of unknown extent, and an area of basalt outcrop totaling 1.5 square miles. A veneer of windblown sand covers about one-half the study area.

Jan 1, 1989

By M. R. Geer

The Bureau of Mines examined the washability data for 25 Appalachian coals requiring low-density washing to reduce sulfur content to 1 percent, using the distribution-curve method. The purpose was to estimate how closely theoretical sulfur values could be approached, what yields of washed coal could be expected, and the recovery efficiencies that might be achieved. Assuming that the run-of-mine coal would be crushed to 3/8 inch and cleaned in dense-medium cyclones, the calculations indicate that theoretical sulfur contents could be approached closely when cleaning at a specific gravity of separation as low as 1.30. With coals that have favorable specific gravity compositions the recovery efficiency anticipated for cleaning at 1.30 specific gravity is surprisingly high. Similar calculations for cleaning with concentrating tables at intermediate specific gravities indicated that theoretical sulfur contents at 1.50 specific gravity could be approached closely with some coals but not with others. The calculations suggest that operating a table at a specific gravity of separation much lower than about 1.50 probably would be unsatisfactory with most coals.

Jan 1, 1968

By N. Greninger

The Bureau of Mines examined the possibility of a seasonal variation of respirable dust concentration in U.S. coal mines. The first step was to review company and MSHA-inspector dust samples that had been collected during the past several years in 14 selected mines for compliance purposes. Results indicated severe scatter in data; most standard deviations of the dust concentrations measured in winter and summer months were comparable in magnitude with the mean values of dust concentrations for the seasons. Therefore, a detailed statistical analysis was conducted. At the 90% confidence level, the company samples of three mines had winter means 0.15 to 0.54 mg/m3 higher than the summer means; six mines had negligible seasonal variations; and five mines had winter means that ranged from higher to lower than the summer means. Inspector data, however, were too sparse for analysis. In view of both the low frequency of occurrence of a seasonal effect and its wide scatter in several of the mines, the study was ended with the conclusion that seasonal varia-tion in respirable dust levels, in general, is an insignificant factor.

Jan 1, 1986

By Paul M. Tyler

This paper is one of a series of digests of foreign mining legislation and court decisions prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Yugoslavia was prepared from information furnished by John Dyneley Prince, American Minis- ter at Belgrade, in response to a questionnaire submitted by the Bureau of Kinos and transmitted through the courtesy of the Department of State.

Oct 1, 1929

By J. P. Hansen

Reducibility tests were run by the Bureau of Mines on an open hearth lump ore and four groups of pellets whose smelting characteristics had been deter-mined previously in the Bureau's experimental blast furnace. When reduction data from various tests were plotted on specially prepared paper l-(l-percent reduction/100)1/3 against time, the plots were linear. The iron-wustite inter-face therefore advances at a constant rate. The rate of the interface advance in mm/min was used as a reducibility index. The reducibility index measured at 900° C, using 0.45 cu ft hydrogen per minute varied inversely with the surface area of the sample. Even with carefully controlled surface areas, how-ever, duplicate reducibility indices varied considerably. When enough tests were run to give a stable mean, the mean reducibility index did correlate with blast furnace production for the four pellet groups. Results indicated that if the interface speed itself were to be used for correlation with blast furnace production, a sample size of about 180 grams of minus 0.742-plus 0.525-inch particles should be used with a test temperature of 900° C and a flow of 0.45 cu ft hydrogen per minute.

Jan 1, 1966

By R. C. Anderberg, F. J. Caervenyak, F. J. Frattali, H. J. Kandiner, R. A. Brown

"INTRODUCTION Considerable interest was shown .prior to and during World War II in the winning of metallurgical-grade alumina from anorthosite, kaolin, siliceous bauxites, diasporic clays, and other aluminum-bearing ores. Laboratory and pilot-plant investigations were made on many of these ores by the Bureau of Mines, and a series of reports on them is being prepared. This report covers the tests made on the application of the lime-soda-sinter process to anorthosite, which is a mixture of albite, NaAlS1308, and anorthite, CaAl2Si208. Extensive deposits of anorthosite occur in the Laramie Range in Wyoming and extend into Colorado; other deposits are found in New York, with outcroppings appearing in Vermont, Maine, and Labrador.Anorthosito can not be treated by the Bayer process for the production of metallurgical-grade alumina, because excessive losses of soda and alumina occur from the formation of sodium-aluminum silicate due to the large amount (50 percent) of silica in the ore.RESULTS OF INVESTIGATIONSSmall-scale laboratory tests supplemented by pilot-plant runs have demonstrated that the alunina and soda occurring in the Wyoming anorthosite from the Laramie Range can be extracted and recovered satisfactorily by the lime-soda process. It has been shown that liquors containing approximately 95 gram of A1203 per liter can be consistently produced at Na20:A1203 ratios from 1.75 to 2.27, and that these liquors can readily be desilicated and carbonated to yield high-grade alumina trihydrate of quality comparable to that essential for cell-grade alumina. The optimum results were obtained with Na20:A1203 mol ratio of 1.03 and Ca0:Si02 ratio of 2.14 in the sinter when calcined at an average temperature of 2,444ºF. for 25 minutes."

Nov 1, 1947

By Alfred R. Powell

In another paper the writer has described an investigation in which the forms of sulphur in coke were determined and described. Coke was found to contain four characteristic forms of sulphur- namely, ferrous sulphide, sulphates, ad- sorbed free sulphur, and sulphur held in solid solution in the carbon. While the coke is still in the oven, only two forms of sulphur are present namely, the ferrous sulphide and the sulphur in solid solution in the carbon. During the quenching, however, the sulphur of the coke is subjected to considerable oxidation, a portion of the ferrous sulphide being oxidized to free sulphur and sulphates, while the solid solution form remains unchanged. The coke, however, loses no sulphur during this process, since the free sulphur which is formed ie retained by the coke in an adsorbed form. Since this oxidation of the ferrous sulphide took place so easily, an inves- tigation was undertaken to determine whether this property could not be taken ad- vantage of in some industrial process for the desulphurization of coke. Although it is true that such a roasting process would not touch the solid-solution form of sul- phur, still the removal of the ferrous sulphide sulphur would undoubtedly benefit the coke from the standpoint of the metallurgist. This improvement in the coke would result not only from the decrease in total sulphur, but also from the large decrease in the ferrous sulphide, which is responsible for the contamination of the iron in the upper part of the blast-furnace. The de sulphurization of coke by roasting in air it a new idea, but dates back to the earliest days of coke manufacture. In 1871, Philipparts published the results of some work done by him on the de sulphurization of coke by air, as well as a review of the results of earlier investigators. In the se earlier experiments, nothing was known of the forms in which the sulphur existed in the coke, while the temperature measurements were only approximate, so that altogether the results were not very conclusive nor complete. The de sulphurisation figures given by the se early investigators generally showed a low efficiency for the process, but some extraordinary results were claimed by certain inventors. In the light of our new knowledge concerning the coke sulphur, it seemed to be important enough to warrant investigation.

Apr 1, 1923

By J. P. Bennett

The Bureau of Mines is investigating the acid resistance of ceramic materials to identify construction materials for emerging technology in chemical and metallurgical processes. Eight commercial ceramic materials, including two red shale, two fireclay, a silica, a silicon carbide, a carbon, and a high-alumina brick, were evaluated. Samples were exposed to 40 wt pct HN03 at 70° and 90° C and 60 wt pct HN03 at 50°, 70°, and 90° C for time periods of 110 days. Statistically significant changes in cold crushing strength were generally small or not detected, except for a strength drop in the high-alumina brick, which decreased in strength when exposed to the chosen acid concentrations at 90° C. Vol-ume and weight changes were also measured. The leach rates of Al, Ca, Fe, K, Mg, Na, Si, and Ti were monitored. Increasing temperature or a decrease in the acid concentration resulted in an increased ion leach rate. Of the conditions tested, the most severe corrosion occurred at 90° C for a 40-wt-pct-HN03 solution. The silica brick had the best overall acid-resistant properties, followed by a red shale and a fire-clay brick. The carbon and silicon carbide bricks are not recommended for service.

Jan 1, 1984

By D. A. Hill

This volume contains a summary of the results of past analyses on U.S. Bureau of Mines Contract No. H0122061 which are relevant to electromagnetic location in mine rescue situations. The analytical results indicated that detection of a trapped miner equipped with a special transmitter is feasible in most situations. Location of the miner by surface measurements is also generally feasible within certain errors. The feasibility of miner detection and the accuracy of miner location have been examined theoretically for a wide variety of situations. Agreement with experimental results is generally good in cases where measurements are available.

By E. R. Cole

The Bureau of Mines developed a procedure that enables substitution of zinc cathodes for the aluminum cathodes normally used in commercial zinc electro-winning. Using zinc cathodes eliminates the necessity for stripping and makes it possible to electrowin zinc from solutions derived from material containing excessive amounts of soluble fluorides; for example, zinc concentrates obtained as a byproduct of fluorspar mining in Kentucky and Illinois. To demonstrate the viability of using zinc cathodes, fluoride-containing zinc concentrate was roasted, leached, and purified according to current commercial practice. Electrolysis was carried out in 0.8-, 1-, 5, and 10-liter cells at 35° to 40° C with a cathode-current density of 8 amp/dm2 in a solution containing 65 g/l Zn++ and 200 g/l H2S04 using PbO2 anodes. Zinc deposits were produced on zinc cathodes with good morphology and excellent current efficiency (90 to 94 pct) in solutions containing enough fluoride (~0.5 g/l, F+) to cause sticking of zinc to aluminum cathodes. The approach described has failed previously because of severe solution-level corrosion of the zinc cathodes. The present investigation found that the use of a simple mechanical barrier to prevent oxygen migration from the anode was sufficient to prevent solution-level corrosion of the zinc cathode starting sheet.

Jan 1, 1979

By J. R. Thoenen

During the year 1927 the Bureau of Mines, at the request of a number of quarry operators, undertook to make a study of quarry operating costs in order to determine average costs for certain operating conditions and to suggest a model cost accounting system for quarry operations. A detailed questionnaire was prepared and mailed by the bureau to all quarries on its records as employing ten or more men in 1926.

Jan 1, 1929

By Oliver Bowles

The exingencies of a world war have brought home to the American public, especially the people of the. Eastern States, the urgent need for conserving fuel. Transportation problems in the East have created an unprecedented situation wherein fuel-oil supplies are greatly restricted, and the consequent increase in demand for coal further complicates the problem of transporting and storing that commodity. People should awaken to the need for utilizing every possibly means of conserving to fuel, even to the extent of reducing the temperature in their homes.

Jan 1, 1942

By George S. Rice

"It is well known that the lost coal left in the ground in mining, under such conditions that recovery is practically impossible, constitutes a large proportion of the coal in the beds worked. A recent estimate, in a paper on ""The World's Fuel Supply"" presented by Prof. L. P. Breckinridge, of Yale University, before the Annual Meeting of the. American Society of Mechanical Engineers, places the average loss in bituminous coal mining as one-third left in the ground.The bald statement that there is a loss of one ton of coal for every two recovered may seem to those not familiar with coal mining to imply inexcusable and wanton waste. Perhaps a better way of expression is in terms of total recovery rather than in terms of losses. Many mine superintendents and mine owners will readily concede that their total recovery may be only 60 to 75 per cent, but to state that they are wasting 25 to 40 per cent arouses antagonism. The suggestion is of willful waste, whereas the majority of the operators try to the best of their ability to get a high recovery under the adverse and complex conditions that confront them. These involve natural, commercial, and labor conditions, and the requirement in many cases of boundary pillars under railroads and buildings, which may be called for in the deed or lease, or in the absence of specific exemption in the deed or lease, the common law requirement that a surface owner is entitled to the support of the surface."

Apr 1, 1921

By Alton B. Cook

Equipment has been designed and fabricated for study of the vaporization of oil during gas-cycling operations, A sand-packed steel tube, which can be rotated to minimize gravity drainage, is used as a model oil reservoir. A minute windowed cell at the discharge end of the tube through which the liquid-gas interface may be observed, makes possible the separate removal of produced free gas and gas-saturated oil. The operation of the model oil reservoir, and auxiliary equipment, are described by use of a schmatic flow diagram. Details of the specially designed equipment are illustrated by isometric and pictorial drawings, and a description of the experimental procedure is given.

Jan 1, 1959

By E. C. Baker

The capital investment and operating costs of two methane-control systems used during longwall mining operations are compared in this Bureau of Mines report. Costs are given for a surface gob hole drainage system and an underground cross-measure borehole drainage system to control methane gas in gobs in four coal mining areas--central Pennsylvania, northern West Virginia, southern Virginia, and northern Alabama. Present-worth analysis is used to determine the more cost-effective alternative in each location. The alternatives have equal lives and provide the same service based on a minimum rate of return of 15 pet. In central Pennsylvania and northern West Virginia, the gob hole system is more cost effective than the cross-measure system, by 10 and 18 pet, respectively. In southern Virginia and northern Alabama, the cross-measure system is more cost effective, by 29 and 38 pet., respecitively. Costs for other locations must be developed on a case-by-case basis.

Jan 1, 1988

By James A. Powell

The theory of electromagnetic fields indicates such fields could be used to detect and locate trapped miners. To be useful, the hardware of the system must meet a number of requirements, including small size, intrinsic safety, and rugged construction. Such hardware has been built, and the system has been tested by the Bureau of Mines and its contractors. These tests indicate that the electromagnetic method provides a practical means to locate miners in emergencies.

Jan 1, 1976

By Charles Seitz

The Bureau of Mines has modified its parts-per-billion helium-4 analyzer to improve the analytical capabilities of the instrument. The modifications resulted in the following improvements: (1) The analytical precision of the instrument for 10 consecutive analyses was improved to ±1 ppb at the 5,000-ppb helium-4 level, (2) the helium-4 sensitivity was increased almost tenfold, and (3) the minimum detectable limit for helium-4 was improved to 0.5 ppb. The modifications made to improve the instrument included replacing the ion-source control circuit with a direct-current solid-state design, controlling the temperature of the ion source, stabilizing and reducing the pumping rate of the vacuum system, and optimizing peak integration.

Jan 1, 1986

By Sidney Katell

The reaction of coal, oil, or natural gas with air and oxygen and/or steam yields a gas containing varying amounts of impurities. Depending on the raw material and the end use of the product, these impurities include solids, such as dust or slag, and gases, such as hydrogen sulfide, carbon dioxide, and nitrogen. Considerable effort has been expended in developing and operating purification systems, and the literature is replete with equipment data and operating results. The research problems, the design, and the operation of the various systems have been the subjects of patent applications, journal articles, and textbooks.

Jan 1, 1959

By Louis C. Brichta

The Rush Creek district of Marion County, Ark., has had a more or less continuous record of zinc production over the past 40 years. The ore has come from many small mines working on oxidized and semi-oxidized deposits found in the Everton formation where that formation forms the present surface rock. Prospecting has been restricted to the hillsides above the creek levels, the actual ore outcrops being the guides. Little attention has been paid the possible sulfide zones. In August 1942, the United States Geological Survey and the Bureau of Mines recommended exploration of the Powell and Cotter formations, which underlie the Everton, for which purpose the Survey had previously located 18 proposed drill-hole sites in geological structures that seemed favorable to are deposition.

Jan 1, 1949

By J. B. Littlefield

The Greenburg-Smith impinger was developed at the Bureau of Mines in cooperation with the United States Public Health Service in 1922 in the course of an investigation of dust-sampling instruments available at that time. Although it is not used extensively outside of the United States, it is now soused in this country to collect samples for the determination of any dustiness, and most of the information correlating degree of dustiness with physiological effect has been obtained by the impinger method. The chief disadvantages in the use of the regular impinger, especially in mines and other places accessible with difficulty, are its bulk weight, and power requirements. It requires a source either of electricity or of compressed air, which necessitates connections and extension of existing supply lines to each sampling point; the only alternative is the use of a relatively large pump hand-operated with considerable effort.

Jan 1, 1937